Product User Manual
Contents
1. Electronic Central MC8 Electronic central for the automation of awnings with option to connect a tuned courtesy light operating via Radio commander and Wireless Sensor Sun Wind Rain ECHNICAL CHARACTERISTICS Supply Exit motor Exit Courtesy light 230V 50 60Hz 1100W max 230V 500W Max 230V 500W Max Working temperature 10 55 C Radio receiver 433 92 MHz Compatible radio commanders 12 18 Bit Rolling Code Nr memorisable Radio commanders 7 Max Number memorisable Wireless Sensors 1 Max Dimensions 110 x 55 x 25 mm ONNECTIONS TERMINAL Box CN1 Input connection Aarding Input line 230V Phase Input line 230V Neutral Exit Motor Up Exit Motor General Exit Motor Down Exit Courtesy light 230V Neutral Exit Courtesy light 230V Phase CONDUBWNE ONNECTIONS TERMINAL Box CN2 l Input mass antenna 2 Input pole antenna NITIAL OPERATING MopeE The device is operational only in combination with one or more radio commanders upon switching on the central for the First time not a single radio commander code is stored in the 3 D 3 OPERATING AWNING WITH SEVERAL RADIO COMMANDERS IT is possible to program several models of radio commanders by saving one code 1 key a cyclic operating Step Step is obtained Up Stop Down by saving two different codes 2 keys two different commandos are set up the first for Up and the s2. off option not saved Led blinking option selected Led Off No code No code Time motor 3 min E MO a Code Pgm Code Courtesy light Pgm Time Motor Pgm Reference 1 CODE 2 CODE LAMP 3 T MOT 1 CODE Programming radio commander for operating the Awning and Wireless Sensor Programming radio commander 1 or 2 Keys and Wireless Sensor Programming codes for transmission of the radio commander is executed as follows press the key SEL LED CODE starts blinking at the same moment send the previously chosen code with the radio commander of your choice the LED CODE starts blinking very quickly send the second code to be saved LED CODE remains on and programming is completed If the second code is not sent within 10 seconds the central will quit programming mode and selects operating the Awning with one single key of the radio commander If all 7 codes have been saved in case of a successive programming the signalling LEDs start blinking very quickly to indicate that further saving is no longer possible Programming Wireless Sensor Sun Wind Rain Rev 1 1 05 07 10 For saving a Wireless Sensor proceed as described above for programming a radio commander with 1 single key Maximal memorisable number of Wireless Sensors The central allows saving one single Wireless Sensor if the programming is repeated for a new Wireless Sensor the previously saved old code gets lost irreversibly Signal no commun
3. amming Radio control and Wireless Sensor from a distance The central allows programming a Radio commander or Wireless Sensor without interfering directly on the key SEL of the central by executing the operation from a distance Programming a code Radio commander or Wireless Sensor from a distance is done as follows send the previously saved code of the radio commander continuously for over 10 seconds at the same time the central goes into programming indicated by blinking of the lamp send the code of the radio commander that has to be saved or the Wireless Sensor by means of the key provided inside the Sensor a confirmation of being programmed is indicated again by blinking of the lamp Repeat the operation if other devices have to be saved in the memory The central has been equipped by the constructor for programming a transmission code from a distance standard activated if you want to deactivate this function you need to proceed as follows reassure the extended menu 1 has been activated indicated by the alternating blinker of the Led CODE LAMP and Led T MOT go with the key SEL to the blinker of the LED CODE then press the key SET at the same time the LED CODE will switch on permanently and programming is completed Repeat the operation if you want to restore the previous configuration RESET If you should restore the standard configurations of the central press the keys SEL and SET simultaneously so as to have
4. econd one for Down Operating Awning with radio commander 1 Key By operating the radio commander with one single key the functioning is executed as follows the first impulse activates the movement Up until timeout of the motor The second impulse activates the movement Down of the guiding systems if this impulse is made before the timeout of the motor the central will stop the guiding system a next impulse has the motor restart in the opposite direction Operating Awning with radio commander 2 Keys By operating the radio commander by means of 2 keys the functioning is executed as follows the first key Up associated with the movement up operates Up until timeout motor and the second key Down associated with the movement Down operates the movement Down of the guiding system If a new command occurs during the movement Up the central will proceed with the movement Up whereas if a commando Down occurs the central will stop the movement The same principle applies to the phase Down INVERSION OF THE ROTATION MOVEMENT Whenever it occurs during the commando Up of the radio commander the central associates the movement down instead of up for the guiding system one simply needs to repeat the programming procedure by pressing the key Down instead of Up or by inverting the cables Up and Down at the motor CENTRALIZING A GROUP OR GENERAL Centralizing via radio by means of radio commanding Cen
5. ication Sensor If there is no communication any more between the Wireless Sensor and the central pulling up the guiding system will be activated automatically after 20 minutes for security reasons If communication is not restored further commands and in any case the central will be brought into security mode Delete To delete all saved codes for operating the Awning Radio commanders and Wireless Sensors proceed as follows press the key SEL LED CODE starts blinking then press the key SET LED CODE goes out and the procedure is completed 2 CODE LAMP Programming radio commander for Operating the Courtesy light Programming radio commander Programming codes for transmission for radio commanding is done as follows press the key SEL LED CODE LAMP starts blinking send at the same time the previously chosen code with the radio commander of your choice LED CODE LAMP remains on and programming is completed If all 7 codes have been saved in case of a successive programming the signalling LEDs start blinking very quickly to indicate that further saving is no longer possible Delete To delete all saved codes for operating the Courtesy light proceed as follows press the key SEL go to the blinking lamp of the LED CODE LAMP then press SET LED CODE LAMP goes out and the procedure is completed 3 T MOT Programming Time Motor max 4 minutes The central is equipped with a timer to supply the motor equal to three mi
6. ntee a correct functioning of the radio receiver in case two or more centrals are used it is recommended to install them at a distance of at least 3 meters from each other In case as mentioned above two or more centrals are being used it is recommended to use only one Sensor type STATHUROE SHORES SMETEN HES BUT Wireless in order to avoid interfering icine Ni laser ei ks All operations requiring opening the casing connecting the cables programming etc have to be executed during installation by specialised staff only Contact the technical assistance whenever the casing should be opened again afterwards for reprogramming repair or modifications of the installation Stateurop declares that the product MC8 complies with the Directives R amp TTE 99 5 EC EMC 2004 108 EC LVD 2006 95 EC oO m O as en O D w ts J pon D oO oO IMPORTANT NOTICE FOR THE USER The device should not be used by children or psychophysical disabled people without supervising or without explanation on the functioning and instructions for use Children should not be allowed to play with the device and all radio commanders have to be kept away from them ATTENTION this manual with instructions has to be preserved and the important safety prescriptions have to be complied with Not observing the prescriptions can lead to damage and severe accidents The system has to be inspected regularly to detect even
7. nutes LED T MOT OFF Programming time motor has to be done with guiding system down as follows Proceed with the key SEL towards the blinker LED T MOT and press the key SET continuously the guiding system starts going up upon reaching the intended position release the key SET at the same time saving time motor is stopped and the LED T MOT remains on If an automation with control stop is used we advise to set up a time reaching some seconds later than the moment the guiding system attains the control stop If an infinite time motor is needed proceed in the same way as above but press the key SET less than two seconds continuously the LED T MOT remains on and programming an infinite time is completed It is possible to repeat the Operation in case there is an error at programming EXTENDED MENU The central has been provided by the constructor with the option to choose the functions of the main menu only If you want to activate the functions described in the extended menu proceed as follows press the key SET continuously for 5 seconds the blinker Led CODE LAMP and Led T MOT Light up alternated in this way you have 30 seconds to select the functions of the extended menu using the keys SEL and SET after 30 seconds the central returns to the initial mode Reference Led Led Out Led On PGM from distance ON PGM from distance OFF Blinking ON OFF Blinking ON OFF A CODE B CODE LAMP C T MOT A CODE Progr
8. the signal LEDs switched on both immediately afterwards they go out Rev 1 1 05 07 10 IMPORTANT NOTICE FOR THE INSTALLER De central is conceived by the constructor so to allow the Attention automation of the guiding system in order to comply with the prescriptions of the regulations in force The effective compliance to the obligations and observing the minimal safety requirements however should be taken care of by the installer It is recommended to execute the installation according to the directives EN 60335 2 97 Safety of devices for domestic use and similar part 2 Specific regulations for motors for movement of roller blinds parries awnings and similar roller devices The central should be connected permanently onto the power network and doesn t contain any type of line interrupting device for the electrical line 230 Vac as a consequence the installer should provide a line interrupting device for the unit An omnipolar switch of category III should be installed as well The latter has to be positioned so as to be protected against involuntarily disconnections It is recommended to use flexible wires for the connections supplies exit motors stored in an insulating sleeve of polychloropreen of an adjusted type HO5RN F with a tube diameter of at least equal to 0 75 mm The connecting wires have to be assembled fixed into cable seals provided inside the product In order to guara
9. tralizing one or more centrals via radio allows you moving Up or Down simultaneously several Awnings Centralizing is done by the input of the same codes of a radio commander keys at all of the centrals or a Group located at a distance of maximum 20 meters away from the commanding point so as to become a general or partial movement of several automations In order to obtain a satisfying result of the centralization the place where to install should be chosen with utmost care The range not only depends on the technical characteristics of the device but varies also according to the radio electrical conditions of the location FUNCTIONING COURTESY LIGHT BY RADIO COMMANDER It is also possible to programme an additional code 1 key for radio commanding to operate from a distance switching of a lamp 230Vac connected to the terminal box 8 9 CN1 on and off Important each time the awning has been pulled up completely the central will always switch off the courtesy light ROGRAMME KEYS AND SIGNALLING LED S Key SEL select the type of function to be saved the choice is indicated by a blinking Led By pressing several times on the key the function of your choice can be selected The selection remains active for 15 seconds indicated by a blinking LED where after the central returns to the initial mode Key SET executes programming the function selected with the key SEL Signalling Led s Led on option saved Led
10. tual signs of damage The device should not be used if reparation is needed T MOT CODE LAMP CODE e le SEL SET ANTENNA 3 Rev 1 1 05 07 10
Download Pdf Manuals
Related Search