User Manual
Contents
1. At this point do not yet insert the front element back to its place since it has to be unassembled while setting up the system Flip the lens back upright in a stand Your lens is now ready for the setting up Fig 3 T Setup Instructions Anamorphic Lens Setup Instructions Anamorphic Lens Setting up the system STEP 4 Make sure the projector is turned on Itis helpful to have a picture that fills the entire panel of 16 9 projector With a 2 40 1 source material the vertical expand is good to be performed to the picture at this step Fig 4 Now carefully adjust the focus of projector Also make sure the image is symmetrically in the center of the 2 40 1 screen STEP 5 First move the prisms to the out mode using the supplied remote controller until the prisms stop Carefully position the lens with a stand in front of the projector with the small opening closest to the projector lens and the large opening pointing towards the screen Now manually adjust the lens in a stand Make sure the entire beam fits centered within the two lenses Fig 5 Lower raise and tilt the lens until the desired height and angle is reached Make sure the image is now rectangular and still symmetrically in the center of the screen NOTE The optimum symmetry for the projected picture can only be found by tilting the lens to the direction of the beam front view rear view Fig 6 Fig 5 STEP2. 6 Using the remote control press in until the prisms stop again The tuning of picture width can be accomplished manually by adjusting the cap screws inside the lens to match your screen perfectly on both sides NOTE Tuning is done with the cap screws to where the prisms stop after turning the prisms to the in position Fig 6 front view Fig 7 STEP 7 rear view If the sides of picture are not opening closing synchronously to each other when switching the modes tune the terminal screws to where the prisms stop after pressing the out button Fig 7 Open the cap screw of the prism which had a shorter travel and close the cap screw of that prism which had a longer travel until both sides of picture are opening and closing synchronously to each other STEP 8 Take the front element remove the cover sheets and secure it to the lens body using the four screws Fig 8 You slightly have to zoom in the picture after front element installation Also now adjust the focus and picture in a in mode to achieve the optimum settings and note these settings as for future reference Fig 9 Maintenance Fig 8 STEP 9 In case the friction based lens height Fig 9 a or the tilt Fig 9 b adjusting mechanism become too loose it is possible to get them tightened with the set screws of stand drums on both sides of lens Use the L wrench 4 mm for tightening the screws You re done Enjoy y
3. Anamorphic Lens Anamorphic Lens Setup Instructions A Lecture La INSTALLATION INSTRUCTIONS Carefully remove and unwrap all the contents of box Referring to the parts list make sure you have everything needed to proceed with the installation of the lens If any parts are missing contact Prismasonic immediately Inspect the lens to make sure there are no shipping defects If you notice a problem with the lens itself or the lens mechanical system contact Prismasonic immediately Parts list E Lens Unit E Table Stand E Power Cord E Power Converter E Remote Controller E L Wrench 3 mm E L Wrench 4mm E Instruction Manual Bringing the lens into the use STEP 1 Lift the lens up and flip it upside down ina stand By using the L wrench 3 mm remove the delivery lock screws of prisms from bottom plate Fig 1 a After this carefully remove the front element by releasing the four cap screws Fig 1 b Put the front element in a safe place waiting for the further use After this remove the bottom plate of housing by releasing the four screws on the bottom plate Fig 1 c Fig 1 STEP 2 Now carefully take off the plastic cover sheets from both sides of both lenses Fig 2 Remove also the cover coats from both IR windows of motor box Fig 2 STEP 3 Insert the bottom plate back to the housing and prepare to affix the four screws Fig 3 with L wrench 3mm Tighten the screws securely
4. our new 2 40 1 picture Your Cinomorph lens was designed to require very minimal cleaning It is best to only wipe the lens housing with a clean damp soft cloth when needed Cleaning the optics Only use optically safe lens cleaning solutions and a clean lint free cloth certified for cleaning of lens materials In order to clean the optics from both sides the bottom plate can be temporarily removed
Download Pdf Manuals
Related Search