DrawerVault Biometric Model GVB 3000 User Manual
Contents
1. DrawerVault Biometric Model GVB 3000 User Manual Patented Rev 1 10 11 Firearm Safety WARNING The DrawerVault Biometric safe or any other firearm storage device cannot take the place of other safety procedures including advising children of the dangers of firearms WARNING The manufacturers and distributors of the DrawerVault Biometric safe do not recommend suggest advise promote or otherwise condone the ownership or use of firearms We at GunVault Inc believe the decision to own or use a firearm is a serious decision that should only be made by an adult who has carefully considered the risks and benefits of such a decision WARNING The keypad and push buttons on the control panel are electronic They have a certain feel to them and may seem different to different people It is important for you to become accustomed through practice as to how the DrawerVault Biometric safe responds to your own personal touch WARNING Never mix alcohol or drugs with firearms or the DrawerVault Biometric safe Alcohol and other substances likely to impair normal mental or physical functions should not be used before shooting or handling firearms or the DrawerVault Biometric safe WARNING Never grab your firearm by the trigger when removing or placing into the DrawerVault Biometric safe Make sure your firearm s safety mechanism is on WARNING Always point your firearm in a safe direction Common sense should dictate which directio2. the LED will flash green two times and you will hear two beeps then the unit is open If the unit doesn t detect a match the LED will flash green and red you will be denied access If an enrolled user is denied access please try again If the problem persists please delete all users and re enroll again Key Access NOTE Key Access is intended for backup use only Insert the key into the front of the unit Turn clockwise to unlock the unit Lift the top of the DrawerVault Biometric to open To remove the key close the DrawerVault Biometric turn the key counterclockwise DELETING USERS RESETTING THE UNIT NOTE Individual users cannot be deleted from the DrawerVault Biometric All users will be deleted together e To delete all fingerprints currently stored on the DrawerVault Biometric press and hold the Delete Button the LED will turn red and then press the Start Button e The unit will beep twice and the LED will flash green twice indicating all users fingerprints are deleted If no fingerprints are stored the red led will flash once and beep once Replacing the Battery NOTE Low Battery Warning When the unit is powered on if the LED flashes red and the unit beeps 3 times this indicates a low battery e Pull open the battery cover e Pull out the battery holder by gently pulling on the ribbon a Remove old battery b Insert new 9v battery following the Positive and Negative guides on the hold
3. ance policy The Company is not responsible for damage to or theft of the Purchaser s DrawerVault Biometric safe or its contents 8 We recommend that the enclosed warranty card be completed in full and returned to the Company within ten 10 days of the original date of purchase to validate this warranty 9 Any implied warranties which the purchaser may have are limited to the duration of the warranties described above There are no further warranties which extend or apply beyond the face hereof and the company expressly disclaims and excludes any and all warranties of merchant ability or fitness for a particular purpose Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you 10 Repair or replacement shall be the sole remedy for the purchaser under this warranty The Company shall not be liable for any direct indirect incidental or consequential damages losses or expense arising from the use or misuse of the DrawerVault Biometric safe Some states do not allow the exclusion or limitations of incidental or consequential damages so the limitation may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state 4 10 Inquiries or questions regarding the DrawerVault Biometric should be directed to GunVault Inc Technical Support 800 222 1055 Protected by United States Patent Numb
4. e device In addition it is recommended that you practice the authentication process several time in order to become comfortable with the process About DrawerVault Biometric DrawerVault Biometric is the ultimate solution to complete access control Invented and developed by GunVault DrawerVault Biometric provides safe storage and easily controlled access for handguns weapons ammunition jewelry and other valuable items including pharmaceuticals coins stamps stocks bonds critical data and personal documents DrawerVault Biometric requires no external computer or power to function Flash memory retains fingerprint data even during complete battery or electrical failure Shipped with your DrawerVault Biometric are the following items e DrawerVault Biometric e Two backup keys e Instruction Manual GETTING STARTED NOTE Set your keys to the side Don t lock them inside the safe Make sure to remove the backup key from the DrawerVault Biometric before use and secure them The key is for emergency use only to unlock the case in the event of fingerprint failure lf the key is used to access the DrawerVault Biometric it can only be removed from the lock cylinder by returning the key back to its original locked position Please do not try to remove the key in any other position or this may cause damage Do not try to use the fingerprint scanner and electronic locking system while the key is in the unit ee ED Batter
5. er e Reinsert the battery holder and snap the battery cover back into place Installation of Optional Security Hint A pair of needle nosed pliers will be useful for installing the hitch pin Cut outs are provided on both sides of the Drawer Vault to permit attachment of the Security Cable a First loop the end of the security cable through the eye and around a stationary object b Then insert the threaded mount through the hole in the safe c Hold the mount in place while you slide the star washer over the threaded end inside the safe d Spin on the nut and tighten finger tight e Insert the Hitch Pin through the hole in the threaded mount to ensure that the nut cannot come off Safe Mall t diia Hitch Pin Star Washer Technical Support If you have followed the above steps carefully and still have a problem operating your DrawerVault Biometric phone GunVault Technical Support Almost all problems can be solved within minutes over the telephone 800 222 1055 Requirements for Return amp Repair If possible do not return your DrawerVault Biometric safe to your dealer Instead call GunVault Technical Service Department GunVault product delivered without a pre arranged Return Authorization Number may be returned unopened at owner expense and fees may accrue Tr Limited Warranty 1 GunVault the Company warrants to the original consumer the Purchaser that the D
6. ers 5 161 396 and 5 549 337 11
7. green indicating the enrollment procedure has started Swipe the administrator fingerprint from Position 1 to Position 2 Figure C and you will hear two beeps indicating the additional fingerprint is ready for enrollment Place the new finger to enroll over the scanner with the tip of your finger at the top of the finger guide as shown in Figure B Make sure you have good flat contact with the scanner Begin to swipe the new finger from Position 1 to Position 2 Figure C taking 1 to 2 seconds to complete the swipe Try to get your entire fingerprint to cross the scanner Once the swipe is completed you will hear a beep Repeat Step 3 one more time After swiping your finger 2 times the unit will beep twice this indicates a successful enrollment If the swipe fails the LED will flash red and the unit will wait for another swipe ACCESSING THE UNIT NOTE The DrawerVault Biometric can be accessed either by valid fingerprint or via the keys provided Fingerprint Access Press and release the Start Button the green LED flashes two times and the unit beeps once Place your finger over the scanner with the tip of your finger at the top of the finger guide as shown in Figure B Make sure you have good flat contact with the scanner Begin to swipe your finger from Position 1 to Position 2 Figure C it will take 1 to 2 seconds to complete the swipe Try to get your entire fingerprint to cross the scanner lf the unit detects a match
8. n is the safest WARNING Always follow the firearm safety rules set out by the firearm s manufacturer WARNING Be familiar with how firearms work GunVault recommends that you obtain as much information as possible on firearm safety WARNING Always handle firearms as if they are loaded and ready to fire Always assume that a firearm is loaded WARNING In order to enjoy the maximum security benefits of the DrawerVault Biometric safe product it must be mounted in place using the equipment provided with the product according to the instructions provided herein Use of this product as a storage receptacle without mounting according to the instructions provided herein may compromise security of the DrawerVault Biometric Safe Understanding Biometrics Biometrics are methods of authenticating the identity of a person based on physiological or behavioral characteristics Biometric fingerprint authentication refers to technology that measure and analyzes human physical characteristics for identification and authentication purposes Everyone is known to have their own unique individual fingerprints The individuality of each fingerprint can be determined by the pattern of ridges and furrows on the surface of the finger as well as by the minutiae points Minutiae points are local ridge characteristics that occur at either a ridge bifurcation or a ridge ending The biometric scanner is a sensitive device that requires care not to damage th
9. rawerVault Biometric safe will be free from defects in workmanship and materials for a period of one 1 year from the date of purchase These warranties are not assignable or transferable to any other person 2 Any damage to the DrawerVault Biometric safe as a result of misuse tampering abuse neglect accident improper installation modification unauthorized service destruction or the alteration of the serial number or use violation of the instructions furnished by the Company will void this warranty 3 The sole responsibility of the Company shall be limited to the repair or replacement in its sole discretion of any component of DrawerVault Biometric safe which fails to conform to this warranty at no cost to the purchaser for a period of one 1 year from the date of original purchase 4 Contact the Company directly to obtain service under this warranty If it becomes necessary to send a defective product to the Company a Return Authorization Number must first be obtained from the company 5 Products shipped without prior Return Authorization and Return Authorization Number may not be accepted and the Company will not be responsible for their disposition and or cost of return to the owner 6 The Company will not assume any responsibility for any loss or damage incurred in shipping All return authorized products should include a copy of the original invoice in order that this warranty may be honored 7 This warranty is not an insur
10. y Ag eee ea Button ny Delete Button ENROLLMENT OF THE ADMINISTRATOR FINGERPRINTS Figure B NOTE The unit can store 120 fingerprints with the first two enrolled fingerprints assigned as administrators If the Learn Button is pressed and the LED flashes red once and the unit beeps once the unit has reached its120 fingerprints maximum NOTE The unit requires the first or the second administrator s fingerprint to be enrolled before adding additional fingerprints Register the first two fingerprints as the administrator Press the Learn Button You will hear one beep and the LED will flash green indicating the enrollment procedure has started Place your finger over the scanner with the tip of your finger at the top of the finger guide as shown in Figure B Make sure you have good flat contact with the scanner Begin to swipe your finger from Position 1 to Position 2 Figure C taking 1 to 2 seconds to complete the swipe Try to get your entire fingerprint to cross the scanner Once the swipe is completed you will hear a beep Repeat Step 3 one more time After swiping your finger 2 times the unit will beep twice this indicates a successful enrollment If the swipe fails the LED will flash red and the unit will wait for another swipe Repeat steps 1 through 5 to add the second administrator ENROLLING ADDITIONAL USERS Press the Learn Button You will hear one beep and the LED will turn
Download Pdf Manuals
Related Search