USER`S MANUAL compact omnidirectional bar - Opticon-SHOP
Contents
1. that the product should not be thrown in the home waste bin The product must be recycled as an electronic product For proper treatment of end of life products consult the section for Environmental care on www opticon com 3 READING CODES Check the scanning engine m 15 the scanning engine on Is a red light beam visible If not press the triggerkey Approach m When holding the labeled product point the barcode label to the reading window of the scanner m When holding the scanner point the reading window of the scanner in the direction of the bar code label Attention m At least one laser beam of the laser pattern should cover the bar code label width from margin to margin Reading distances varies with the barcode label width m Check the data at the connected computer device A Good Read means that the scanner has effectively recognised and decoded the bar code In most cases the application program will provide an indicator signal or a buzzer signal to indicate a good read to the user When the read is incorrect you can try again paying attention to the instructions below V TROUBLE SHOOTING General checks m Make sure the scanner is installed properly m Check the power supply of all devices 5 the reading window of the scanner clean m Are the bar code labels damaged Scanner does not operate m Check if power supply is connected Check the triggerswitch2. a beep tone indicates when a bar code has been succesfully decoded 5 Cable with connector To connect the scanner to the computer equipment connection accessories as shown in the installation instructions might be required 6 Scanner label A label is affixed to scanner and or cable and contains the serial number Do not remove it 7 Stand optional The scanner can be mounted on a stand R HANDLING INSTRUCTIONS m A Temperature conditions 5 Use in area s between 0 and 40 Do not expose the scanner for a long time to direct sunlight or near direct heat For use under extreme conditions for example freezing area s or temperatures higher than 40 Ke please contact Opticon or your local dealer Avoid contact with water m B Shock Do not subject the scanner to strong impact do not throw or drop the scanner from great heights m Cleaning of the scanner Clean the reading window regularly to maintain optimum reading performance Clean the exterior of the scanner by wiping it with a soft lightly moist cloth Do not use a high pressure cleaning method If a cleaning liquid is needed only use one drop of a non abrasive household liquid D Maintenance There are no user serviceable parts inside the scanner So do not try to take it apart In case of serious malfunction please consult Opticon or your local dealer m E Recycling amp Disposal instructions The icon on the product or package indicates
3. 5724 omnidirectional bar code scanner USER S MANUAL Ee ur u e gt z n Ir Co e INSTALLATION INSTRUCTIONS LIMITED WARRANTY AND DISCLAIMERS FIRST STEP TURN POWER OFF Exercise caution at all times when working with AC and DC powered equipment m Turn off all your equipment before installation It is strongly recommended to use Opticon cables and power supplies NEXT STEPS CONNECT INTERFACE m Find your interface type in the corresponding diagram m Connect the scanner to the computer in accordance with the diagram and corresponding instructions Turn your computer equipment on DIAGRAM AND INSTRUCTIONS See diagram on the left side of this page RS 232 interface cable connection Plug DB9 or DB25 connector into computer terminal Connect external power adaptor USB cable Make sure your computer runs Windows 98 or higher Plug USB A connector of scanner into computer terminal Connect external power adaptor Keyboard wedge connection Disconnect the keyboard Plug the male side to compu
4. m Check if you connected the right interface Bar code label could not be read m Check that the width of the bar code label does not exceed the width of the light beam m Change the angle between the bar code and the scanner m Change the distance between the bar code and the scanner If you can not solve the problem Contact Opticon or your local dealer When the scanner needs to be repaired The label with serial number should be present If returning the scanner please use the original packaging to minimise the chance of damage More information The scanner is configured to default factory settings and is supplied with information that gives you a quick understanding of the product More product details additional support or configuration options to your own preferences by Opticonfigure will be updated at www opticon com OPERATION INSTRUCTIONS ENGLISH The Netherlands Hoofddorp France ISSY Les Moulineaux CEDEX Germany Dietzenbach Italy Castel Maggiore BO Spain Valencia Sweden Jarfalla United Kingdom Luton Bedfordshire U S A Orangeburg Japan Warabi City Taiwan Taipei P R China Shanghai Australia Kariong www opticon com OF TICON
5. ter terminal Plug the female side to keyboard Connect external power adaptor If you have any questions please contact your local dealer or Opticon CAUTION This user s manual may be revised or withdrawn at any time without prior notice Copyright 2005 Opticon Sensors Europe B V All rights reserved This manual may not in whole or in part be copied photocopied reproduced translated or converted to any electronic or machine readable form without prior written consent of Opticon Sensors Europe B V BY OPENING THE PACKAGE OF THIS PRODUCT YOU AGREE TO BECOME BOUND BY THE LIABILITY AND WARRANTY CONDITIONS IN ALL CIRCUMSTANCES THIS MANUAL SHOULD BE READ ATTENTIVELY BEFORE INSTALLING AND OR USING THE PRODUCT Serial number A serial number appears on all Opticon products This official registration number is strictly related to the device purchased Make sure that the serial number appearing on your Opticon device has not been removed Removing the serial number might affect the warranty conditions and liability disadvantageously so please be strict at maintaining the label with serial number on the Opticon product Warranty Warranty period Liability Unless otherwise agreed in a contract all Opticon products are warranted for the period of two years after purchase covering defects in material and workmanship Opticon will repair or at its opinion replace products that prove to be defective in material or
6. workmanship under proper use during the warranty period Opticon will not be liable in cases where modifications are made by the customer In such case the standard repair charge will be applicable The standard charge for repair will also be applicable in cases where no defect is found at all These rules also apply for products that are still under warranty Under no circumstance will Opticon Sensors Europe be liable for any direct indirect consequential or incidental damages arising out of use or inability to use both the hardware and software even if Opticon has been informed about the possibility of such damages Packaging The packing materials are not harmful for the environment We recommend that you save all packing material as it should be used whenever you need to transport your scanner eg for service Damage caused by improper repacking is not covered by the warranty Trademark Trademarks used are property of their respective owners version 02 2006 1 DETAILED VIEW 1 Reading window The scanning engine behind this window will read the bar codes Never obstruct this window 2 Trigger key If trigger function is enabled the trigger key must be pressed to activate the scanner to read bar codes 3 LED indicator If enabled read results of the scanner are indicated by a flashing LED for example when a bar code has been read 4 Buzzer Beeper If enabled
Download Pdf Manuals
Related Search