Installing the Gigaset HC450 door intercom - Home
Contents
1. Door opene Labelling nameplates Label the enclosed nameplates using a waterproof pen Insert them in the recesses in the doorbell keys Position the doorbell key cover on the doorbell key from above and then apply gentle pressure at the top and bottom Replacing nameplates Insert a small screwdriver at an angle in the narrow notch on either side of the doorbell key cover Carefully lever off the cover Remove the nameplate Mounting the HC 450 control unit Requirements The following requirements for mounting must be fulfilled The HC450 control unit contains a DECT radio module This module must be mounted within the base station s radio range typically around 30 m indoors Check the range using the handset before fixing the control unit If a connection from a DECT handset to the DECT base station is possible at the designated location field strength dis play shows at least one bar or a call of long duration is possible with satisfac tory quality you can mount the con trol unit here If there is no connection to the base station at the designated mounting location the range can be extended by means of a repeater placed between the base station and control unit Mount the HC450 control unit at a suit able location along the junction wire between the bell button and bell It is recommended that you mount the unit near the bell transformer This is normally located in t2. 230 V mains Entry lighting 11 Setting up the Gigaset HC450 door intercom system Setting up the Gigaset HC450 door intercom system Once you have installed your HC450 door intercom system you can set up the door intercom at your convenience using a compatible handset Before you can do this however you must register the door intercom system with the base station Registering with the base station Make sure that the control unit is con nected to a power supply If the LED on the HC450 control unit is flashing it means that it is not yet connected with the base station Set the 4 digit system PIN of your base station to 0000 if necessary refer to the manual for your telephone Press the registration paging key on the base station for approx 3 seconds The registration paging key is located on the right beside the charging cradle Go to the control unit and press the pushbutton see illustration on p 10 there within 20 seconds The LED on the control unit will light up continu ously once it has been registered the LED will return to flashing when a call is underway between the door intercom and base station If registration does not take place despite a number of attempts reduce the distance between the base station and control unit the base station can be disconnected from the telephone network to do this and or briefly disconnect the control unit from the power supply befo
3. 24 Guarantee Certificate Ireland sedare aie Sede fracd aries es 25 Technical Data 0 26 IND OX oerien enir ceris a arse tale 27 Safety precautions Safety precautions Caution Read the safety precautions and the manual before use Explain their contents to your children as well as the potential hazards associated with using the telephone Only use the mains adapter supplied as indicated on the underside of the control unit This adapter is only intended for use on the Gigaset HC450 and must not be con nected to other devices Make sure that the mains adapter is accessible at all times Do not continue to use broken plugs or plug in power supply units with broken hous ings as they pose a risk of electric shock Have these parts replaced with genuine spare parts without delay The housing of the HC450 control unit and door intercom must not be opened Unau thorised opening of the housing and improper repairs may endanger the user and will invalidate the warranty The control unit is designed for indoor operation only Lay the cables so that nobody can walk on or trip over them The control unit includes a radio module in accordance with the DECT standard The operation of medical appliances may be affected Be aware of the technical conditions in your respective environment e g doctor s surgery The module must not be installed during a thunderstorm nor should any cable conne
4. 15 External loudspeaker 16 F Frame for surface mounting 8 G GAP ss ee nerd oot wane hans ecole Peat 1 Gigaset Home Control 1 Guarantee Certificate 24 27 Index H Handset operating the door intercom 17 Home Control 22 1 l Incoming call from the door intercom 17 Installation 7 Internal and external call time 15 Internal conversation 17 Internal user Intercom 17 L Labelling nameplates 9 LE a a AEE paity aoe ee 12 LAGI bed aa r veut ates 11 Lights key a eas hoe ee ees 2 M Mains adapter 5 Medical appliances 5 Menu OVEN VIQW naana annann dudsteenaied atau 20 Mounting the control unit 9 Mounting the door intercom 7 N New cabling 10 P Pack contents 4 7 PIN Swit a Saree ie e aA T E gaten 18 system PIN a ae a 12 Power supply unit 11 Q Questions and answers 22 R Radio range 2222005 9 Range of applications 2 Registration paging key 12 Repeater 0 002 005 5 9 28 S Safety precautions 5 Second doorcall 13 SENICE inae erect ee ate 23 Setting the bottom key 13 Shortcuts oke eode eee eas 20 Starting programming 12 Status WaVe ra Bet Che T 18
5. Brief overview Gigaset Home Control Gigaset Home Control is a standard that allows you to control household appliances lights and blinds alarm systems heating and air conditioning systems and door intercoms such as the Gigaset HC450 from a Siemens Gigaset cordless telephone The full functionality of the HC450 door intercom opening the door from the handset forwarding calls to an external number and configuring the system is available in conjunction with Gigaset cord less telephones that support Gigaset Home Control A list of all compatible devices can be found in the Appendix If you operate the HC450 door intercom using a standard DECT cordless telephone DECT technical standard for cordless telephones that does not support the GAP standard only the two way speech function will be available GAP cordless telephones that have been developed in accordance with the GAP standard are compatible with each other This means that handsets from one manufacturer can be operated on a base station from another manufacturer In this case however operation is restricted to the telephones basic functions Brief overview In common with the HC450 door inter com all other products certified for Gigaset Home Control can be easily installed without additional cables and networked with the Gigaset cordless tele phone at the push of a button Gigaset Home Control thus grows with your ne
6. LED flashing gt Register the control unit 2 Control unit has been registered but is dropping the connection LED flashing gt Reduce the distance between the base station and the control unit Install a repeater if necessary Bell not signalling at the mobile phones even through the control unit has a connection to the base station cont rol unit LED lighting up continuously 1 no int Ringing is set gt Select a value between 10 and 60 seconds 2 Call forwarding activated display showing line in use gt Select Status Home 3 Handsets outside of range or switched off specifically set handset deregistered or switched off gt Bring the handsets within the base sta tion s range switch on or charge the handsets gt Select another handset for signalling or switch over to Signal to All Handsets Contact your dealer if the problem persists Gigaset cordless telephones compatible with the HC450 Compatible base stations Gigaset SX440 SX445isdn Gigaset SX450 SX450isdn Gigaset E450 E455 Gigaset E450 SIM E455 SIM Gigaset 440 S445 Gigaset 450 S455 Gigaset S450 SIM S455 SIM Gigaset S450 IP Gigaset S645 Gigaset SL440 Gigaset SL550 SL555 Gigaset SL560 SL565 Compatible high feature handsets Gigaset E45 Gigaset 1 S1 colour Gigaset S44 Gigaset S45 Gigaset SL1 SL1 colour Gigaset SL55 Gigaset SL56 Gigaset SL74 These devices support t
7. cap before mount ing Apply firm pressure to the terminal cap with both thumbs and slide it in the direction of the arrow Installing the Gigaset HC 450 door intercom system The terminal cap will then spring out of the two detent clips Mark the distance between the two drill holes on the wall Drill two holes for 6 mm plugs and fix the control unit using the enclosed screws and plugs For laying the cables a multi core com munications cable is recommended with a wire profile of 0 6 mm After Before Doorbell Control unit i Actua Light tor ETS io Connecting the HC450 control unit Using existing cables Disconnect the existing connection between the doorbell and the bell trans former bell at an appropriate location if possible near where the control unit is mounted see next diagram on left Connect the open ends for the bell transformer bell with the Actuator ter minals in the control unit polarity is not relevant Connect the open ends for the doorbell with the ETS terminals in the control unit polarity is not relevant Caution Cables must not be connected or disconnected during a thunderstorm New cabling Connect the 2 core cable of the door inter com to the terminals marked ETS in the control unit see illustration below Con nect the bell transformer bell to the Actu ator terminals in the control unit Door intercom optional Bell
8. pre vent potential negative consequences for the environment and human health It is a precondition for reuse and recycling of used electrical and electronic equipment For more detailed information about disposal of your old appliance please con tact your city office waste disposal service or the shop where you purchased the product Note Not all of the functions described in this manual are available in all countries Installing the Gigaset HC450 door intercom system Installation of the HC450 door intercom system does not require additional cables to be laid if a doorbell with sound effect is already present You replace the existing doorbell key in this case Begin by checking that you have all the components required for mounting Please read the entire chapter on instal lation carefully before you commence Pack contents 1 control unit with cover 4 plugs and mounting screws for fixing the control unit and door intercom 1 HC450 door intercom 1 frame for surface mounting 1 plug in power supply unit 2 hexagon socket screws for fixing the door intercom to the frame 1 Allen key for the hexagon socket screws 2 clamping plugs for connecting the cables to the door intercom 2 doorbell key covers and nameplates 2 thermal shrinkage tubes Installing the Gigaset HC450 door intercom system Mounting the HC450 door intercom The HC450 door intercom generally replaces the existing doo
9. status Changing the PIN of the door intercom The door intercom allows you to assign a custom PIN to protect its settings against unauthorised access You can change the 4 digit PIN delivery version 0000 to a 4 digit PIN known only to you Call up the menu for the settings see p 12 gt Door PIN gt ed ig Enter a 4 digit PIN and press oq The entry is saved Press and hold return to idle status Note To prevent misuse we recommend assigning a separate PIN each for the door intercom and the base station The door can only be opened from an external telephone see p 19 by entering a separate PIN other than 0000 for the door intercom Making settings for the top doorbell key You can set a specific internal call destina tion handset and ringer tone for the top doorbell key of the door intercom You can also set the doorbell key to call all reg istered handsets Setting up the Gigaset HC450 door intercom system Setting an internal call destination and ringer tone Call up the menu for the settings see p 12 gt Upper Door Key gt A alternatively gt Internal Dest gt A A list is displayed It contains the entry Call All and the internal names of all reg istered handsets The current setting is displayed Select an internal user e g Anna and confirm gt Anna gt D4 If Call All is set an incoming call from the door intercom will be forwa
10. time and thereby frees the line again 19 Menu tree Menu tree Instead of scrolling to locate a menu function you can select a menu function faster by opening the menu see p 12 and keying in the digit combination shortcut Example ME for Language English In the Settings menu of the Gigaset HC450 1 Connect to Door p 17 2 Diversion No p 14 3 Diversion p 14 4 Volume Volume 1 p 16 Volume 9 5 Upper Door Key 5 1 Internal Dest 5 1 1 Call All p 13 5 1 2 INT1 p 12 5 1 6 INT6 5 2 Ringer Tone Melody 1 p 13 Melody 10 GHC Melody 6 Lower Door Key No Function p 13 As Upper Key Second Door Call Light 7 Low Key Setting 7 1 Internal Dest 7 1 1 Call All p 13 7 1 2 INT1 p 12 7 1 6 INT6 7 2 Ringer Tone Melody 1 p 13 Melody 10 GHC Melody 8 Language 8 1 Deutsch p 12 8 2 English 8 3 Francais 8 4 Italiano 8 5 Nederlands 20 Menu tree 9 Timer 9 1 Door Light impulse lsecond 90 second p 15 9 2 Door Bell impulse lsecond 3 second p 15 9 3 Int Door Call no int Ringing 10 second 60 second p 15 9 4 Ext Door Call 30 second 120 second p 15 9 5 Ext Call Dur 30 second 120 second p 15 This setting will only appear if the Second Door Call settin
11. transformer Bell trans l supply unit E Control unit Door opener Bell transformer 10 Connecting entry lighting Installing the Gigaset HC450 door intercom system If you want to use the bottom doorbell key to switch on the entry lighting the light source must be connected to the control unit using two cores see illustration below The entry lighting can also be switched on off by means of a switch con nected in parallel see sketch e g motion detector Alternatively a sensor input from a timing circuit can also be connected Caution The entry light may only be installed by a qualified electrician Installation work on the control unit must only be carried out after the current carry ing devices have been disconnected from the 230 V mains Please ensure that the mains voltage is not switched on again until the installation work has been com pleted Stranded conductors must not be used for the connection and the insulation on the eads must not be stripped by more than 6 mm The shrinkage tubes supplied must be pulled over the two wires see diagram 56mm Thermal shrinkage tubes Connection with the power supply unit Connect the mains adapter with the plug on the right hand side of the control unit and insert the plug in power supply unit into a socket ie Control unit i ETS Light Pushbutton AFN LID KOKO O pea Actuator e
12. 2 222 9 Customer Care 0 23 D DECT h a aa bobs wes Pius BN 2 oa 1 9 DECT radio module 9 Diversion destination 14 Door intercom 12 17 acceptingacall 18 bottom doorbell key 13 calling internally 17 changing the display language 12 changing the PIN 13 clamping plug 04 8 diversion destination 14 duration of the bell 15 external call duration 15 for automatic call diversion USING ia ia aia ae eee 18 incoming call from the door intercom 17 labelling nameplates 9 MOUALING xa tected toe eaten ak bee 7 operating using the handset 17 range of applications 2 registering with the base station 12 second door call 13 setting the call time 15 setting up a call diversion to an external number 14 supplied items 7 surface mounting 8 system PIN 2 00005 12 top doorbell key 13 volume of the external loudspeaker 16 Doorlight 0000000 15 Door opener 20 65 3 Door opener voltage 3 Doorbell ose hae pe be es 7 Doorbell key 2 9 13 Duration of the bell 15 Duration of the door light 15 E Entry lighting 000 2 External call duration
13. NOME aina ma an eae aE tat 18 Supplied items 7 Surface mounting 8 System PIN 22 00008 12 T Technical data 2 26 Terminal cap eee eee eee 9 Top doorbell key 13 Transformer 1 2 2 0 eee ee eee 10 Troubleshooting 22 V Volume of the external loudspeaker 16 A31008 M1799 R101 1 7619
14. Version 12 02 2007 english A31008 M1799 R101 1 7619 Issued by Siemens Home and Office Communication Devices GmbH amp Co KG Schlavenhorst 66 D 46395 Bocholt Siemens Home and Office Communication Devices GmbH amp Co KG 2007 All rights reserved Subject to availability Right of modification reserved www siemens com gigaset Brief overview With the Gigaset HC450 the door inter com becomes an integral component of the cordless telephone system It supports two way speech using any registered cordless telephone which means that the house telephone no longer has to be per manently located in the entrance area The Gigaset HC450 door intercom is suita ble for practically all single family resi dences including those that only have a bell Main features Two way speech with callers to the door using the cordless telephone including handsfree Intuitive operation via the handset s softkeys open door activate entry light Easy configuration using the menu on the handset Forwarding to external numbers Ease of installation and registration with the Gigaset system Replacement of the old bell button with the door intercom the existing cabling is generally adequate for installation Support for existing bell and standard door openers Configuration options for the second bell key separate door call to specific handset activation of entry lighting same function as first bell key
15. act 230 V 10 A must be undertaken by a qualified elec trician The illustration below shows the cabling with an existing doorbell before and the cabling following installation of the HC450 door intercom and HC450 control unit after Door intercom ETS amp E Control unit l supply unit Door opener Bell transformer Contents Contents Brief overview 1 Gigaset Home Control 1 Range of applications 2 Safety precautions 5 Installing the Gigaset HC450 door intercom system 7 Pack contents 0 7 Mounting the HC450 door intercom 7 Mounting the HC450 control unit 9 Connecting the HC450 control unit 10 Setting up the Gigaset HC450 door intercom system 12 Registering with the base station 12 Setting functions 12 Operating the Gigaset HC450 door intercom using the handset 17 Incoming call from the door intercom 17 Calling the door intercom from an internal user 17 Operation with automatic call diversion 0 00085 18 Menu tree 000 20 Appendix se eeo ceeds wae eo es 22 Clea MING ne ais ee nee eas 22 Questions and answers 22 Gigaset cordless telephones compatible with the HC450 23 Service Customer Care 23 Authorisation 00005 24 Guarantee Certificate United Kingdom
16. be called first If no one answers the call will then be diverted If Status Away is set the door call will immediately be forwarded to an external number Example In the Smith family s house handset no 1 rings when the top doorbell key labelled Smith family is pressed Handset no 2 belonging to the son will only ring when the bottom doorbell key labelled Mat thew Smith is pressed The Smith family has activated call diversion If no one from the family is at home then the call will be forwarded to the father s mobile phone Door opener bell and entry lighting The following devices which are not among the items supplied can be con nected to the HC450 and operated Door opener Bell Before Bell transformer The door can be opened from the Gigaset handset or in the case of a forwarded call from a remote location To do this a standard door opener must be connected not supplied The voltage pulse 12 Valternating voltage for opening the door is supplied by the HC450 An existing bell will be con nected to the HC450 After Doorbell Light optional Control unit Actua PLL Ol rower Bell trans Brief overview Door light A light circuit e g the entry lighting can be switched on from the handset and if appli cable via the bottom bell key for between 1 and 90 seconds or also operated in pulse mode The connection to the floating cont
17. c tions be plugged in or unplugged as to do so would expose you to the risk of electric shock Do not allow fluids to penetrate the HC450 control unit and door intercom as this could result in electric shocks or short circuits Do not use your telephone in environments with a potential explosion hazard e g auto paint shops If you give your Gigaset HC450 door intercom to someone else make sure you also give them the manual Mounting installation and startup may only be undertaken by a qualified electrician Please observe the respective national regulations for the installation of electrical and telecommunications systems Installation work on the control unit must only be carried out after the current carrying devices have been disconnected from the 230 V mains Please ensure that the mains voltage is not switched on again until the installation work has been completed Only equipment supplying safety extra low voltage SELV and complying with EN 60950 may be connected to the control unit actuator output Safety precautions All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities This crossed out wheeled bin symbol on the product means the product is cov ered by the European Directive 2002 96 EC The correct disposal and separate collection of your old appliance will help
18. e switched off Activating deactivating automatic call diversion to an external number You can only activate the Automatic Call Diversion function if you have previously entered a diversion destination see p 14 Call up the menu for the settings see p 12 gt Diversion gt od The current setting is displayed Activate or deactivate auto matic call diversion Press the display key continue with Press and hold return to idle status Setting the duration of the door light The following settings can be selected Pulse 1 2 3 10 20 30 40 50 60 70 80 and 90 seconds Call up the menu for the settings see p 12 gt Timer gt I gt Door Light gt A The current setting is displayed Select the desired duration pulse 1s 2s 3s 10s 90 5 Save Press the display key continue with Press and hold return to idle status Setting the duration of the bell You can set how long the bell at the door intercom should sound when the doorbell key is pressed The following settings can be selected pulse 1 2 or 3 seconds Call up the menu for the settings see p 12 gt Timer gt I gt Door Bell gt A The current setting is displayed Select the desired duration pulse 1 2 or 3s Save Press the display key continue with Press and hold return to idle status Setting the internal and external call time for incoming calls from the do
19. eds All compatible devices fea N ture the Gigaset Home Control logo making them very easy to identify Gigaset Home Control You will find more detailed and up to date information together with sources of sup ply for compatible products on the Inter net at the following link www gigaset home control com Range of applications Assigning the two doorbell keys The HC450 door intercom has two door bell keys each of which can be assigned different settings Top doorbell key The top doorbell key activates a connected external bell At the same time an internal call is initiated to a specific or to all hand sets Bottom doorbell key The bottom doorbell key can initiate another internal call other handset or other ringer tone in addition to the external bell Its function can also be set identically to the top key or The entry lighting can be activated when the key is pressed This requires the lighting system to be connected to the HC450 control unit If the bottom doorbell key is being used as a lights key it cannot function as a doorbell key Call diversion If call diversion is activated for the door intercom the door call will then be diverted to the external number The call diversion relates to the top doorbell key The call diversion can be controlled in dif ferent ways If the occupier is at home he she sets Status Home which means that the internal handset will
20. g is activated in the Upper Door Key menu 21 Appendix Appendix Cleaning gt Wipe the HC450 door intercom with a damp cloth do not use solvent or an antistatic cloth Never use a dry cloth This can cause static Questions and answers If you have any queries about the use of your HC450 door intercom contact us at www siemens com gigasetcustomercare 24 7 The table below contains a list of common problems and possible solutions Control unit No function No power supply Check the power supply Door opener not working no switching noise Door opener is not correctly connected or does not conform to the specifications gt Check the installation Check whether the door opener is within the supported speci fication Door opener not working switching noise but door not opening Door opener is not within the specification or not correctly installed mechanically gt Check whether the door opener is within the supported specification or check the installation of the door opener if necessary adjust 22 HC450 door intercom No function no keys lighting up No operating current gt Check the installation check whether the connections at the terminals are in the cor rect connection sequence Door intercom working bell working but not signalling at the mobile phones 1 Control unit is not registered with the base station control unit
21. he entry lighting Press the end call key Note The caller to the door can switch on the entry lighting if set using the bottom door key see p 11 The following features are not available for an incoming call from the door intercom Conducting a conversation Calling back from a conversation with the door intercom Toggling a caller at the door intercom Conducting a conference call with a user at the door intercom Diverting or forwarding an incoming call from the door intercom Calling the door intercom from an internal user You can call the door intercom internally and operate it even if the bell did not ring first To do this you must first select the internal user Intercom at the handset Select the internal user Intercom Open the list of internal users gt Intercom gt G BE Press the display key gt Connectto Door gt A alternatively Press the display key to acti vate the door opener The door opener is activated Or Light Press the display key to switch on the entry lighting Or Press the end call key 17 Operating the Gigaset HC450 door intercom using the handset Operation with automatic call diversion Switching between Status Home and Status Away If you have entered an external number for call forwarding you can switch between Status Home and Status Away The call diversion only ever relates to the top doorbe
22. he full Gigaset Home Control functionality and are marked with the Gigaset Home Control logo notin all countries Appendix Service Customer Care We offer you support that is fast and tai lored to your specific needs Our Online Support on the Internet can be reached any time from anywhere http www siemens com qiqasetcustom ercare It provides you with 24 7 support for all our products It also provides interactive troubleshooting a list of FAQs and answers plus user guides and current soft ware updates if available for the product for you to download You will also find frequently asked ques tions and answers in the appendix of this user guide Personal advice on our range of products is available on our Premium Hotline United Kingdom 0 90 69 50 04 30 You can talk to qualified technicians who will guide you expertly through product information and installation For fast and dependable assistance with any repairs or guarantee warranty claims contact our Service Centres United Kingdom 0 84 53 67 08 12 Please have your proof of purchase ready when calling Replacement or repair services are not offered in countries where our product is not sold by authorised dealers 23 Appendix Authorisation This device is intended for use within the European Economic Area and Switzerland If used in other countries it must first be approved nationally in the country in question Country specific
23. he fuse box Any adjustment required to the fuse box must be undertaken by a qualified electrician Installing the Gigaset HC450 door intercom system To ensure that a suitable mounting location is selected familiarise yourself with the location of the cabling before hand Watch out for the cabling between the bell button the bell trans former and the bell Lay the cables so that nobody can walk on or trip over them Before finally mounting the control unit check the placement of the unit with temporary cabling by per forming a function test control unit can register with the base station sta ble operation possible with adequate connection quality from the handset to the HC450 door intercom You should also refer to the mounting instructions for the HC450 door inter com see p 7 The control unit must not be installed in a fuse box or metal housing The control unit must not be installed near air conditioning systems in areas with strong sunlight or in dusty environments The control unit must be protected from the direct influence of water and chemicals Areas with strong magnetic fields transformers electric motors high voltage lines must be avoided Cables must not be connected or dis connected or the HC450 control unit installed during a thunderstorm Watch out for electrical water or gas lines in the wall if mounting the control unit on the wall Mounting Remove the terminal
24. le to you if there is a door opener connected to your door intercom 9 woe Press the 9 key to open the door taa Enter the 4 digit PIN Caution It is only possible to open the door from an external telephone if a separate PIN other than 0000 has been set up beforehand for the door intercom see p 13 If you enter the PIN correctly you will hear a recorded announcement and the door will be opened The voice connection will still be active you can terminate it by pressing the hash key F If you did not enter the PIN correctly you will hear a recorded announcement Enter PIN You can then either re enter the PIN or re establish the voice connec tion with the caller by pressing the star key Ge To terminate the voice connec tion press the hash key E If the conversation lasts longer than the set external call duration a recorded announcement will sound 10 seconds before the connection is due to be termi nated You can prolong the connection by pressing the key Operating the Gigaset HC450 door intercom using the handset If the set external call duration is exceeded once more a recorded announcement will sound again 10 seconds before the con nection is due to be terminated The con nection will be automatically terminated if you do not press the key with approx 5 seconds Terminating the process Press the hash key Note The door intercom automatically disconnects the line after the set
25. ll key With Status Home the defined inter nal user will be called when a call comes in from the door intercom If the Automatic Call Diversion function is activated and the internal user does not answer the incoming call within the set time see Setting the internal and external call time for incoming calls from the door intercom p 15 the incoming call will be diverted to the defined external number With Status Away the call coming in from the door intercom will be diverted to the defined external number Calling the door intercom internally Initiate an internal call and select the internal user Intercom ED Press the display key if neces sary to change the mode Press and hold return to idle status Note The incoming call cannot be diverted to a fur ther telephone if the external number is engaged when the call comes in from the door intercom or if an answering machine answers The door intercom will not however be con nected with the trunk line in this case 18 Answering a diverted call at an external telephone When you answer the call you will hear a recorded announcement that is repeated at regular intervals You now have the option of accepting the call or terminating the process Press the 1 key to accept the call Press the hash key to end the call The recorded announcement does not offer the option to open the door how ever this option will be availab
26. ll up the menu for the settings see p 12 gt Volume gt Gg Select the desired volume for the external loudspeaker 1 9 Save Press the display key continue with Press and hold return to idle status Note The voice connection between the handset and door intercom is activated during the set ting process This allows you to check the vol ume of the external loudspeaker directly 16 Operating the Gigaset HC 450 door intercom using the handset Operating the Gigaset HC450 door intercom using the handset Operation of the HC450 door intercom is largely identical for all handsets It is described in this manual using the Gigaset S45 high feature handset Some aspects of operation will differ between the stand ard handset and the high feature handset Incoming call from the door intercom When a call comes in from the door inter com the bell will ring either all handsets or just a specific handset will be called depending on the setting If a call diver sion from the door intercom is set up to an external number the call will be diverted to the set number Press the end call key to reject the call Or GA Press the talk or loudspeaker key You are connected with the door inter com Intercom appears in the display alternatively Press the display key to acti vate the door opener The door opener is activated or Light Press the display key to switch on t
27. or intercom You can set how long the handset should ring for an incoming call from the door intercom to an internal user and for a call diversion to an external user The follow ing settings can be selected no int Ringing 10 20 30 or 60 seconds Setting up the Gigaset HC450 door intercom system Call up the menu for the settings see p 12 gt Timer gt fg alternatively gt Int Door Call gt Or gt Ext Door Call gt A The current setting is displayed Select the desired time no int Ringing 10 20 30 or 60s Press the display key continue with Press and hold return to idle status Setting the external call duration for an incoming call from the door intercom If a call diversion is set up to an external user you can restrict the call duration for an incoming call from the door intercom You can define how long a connection can last The following settings can be selected 30 60 90 or 120 seconds Call up the menu for the settings see p 12 gt Timer gt DA gt Ext Call Dur gt Gy The current setting is displayed Select the desired time 30 60 90 or 120s Press the display key continue with Press and hold return to idle status 15 Setting up the Gigaset HC450 door intercom system Setting the volume of the external loudspeaker You can set the volume of the external loudspeaker at the door intercom to nine different levels Ca
28. rage power per channel LED colour Yellow s of the keys Operating 0 C to 40 C temperature Operating 230 V 10 50 Hz voltage Nominal power max 17 VA Output 12VAC 1A voltages 24VAC 0 2A Cable length 1 5m System Power In idle state consumption approx 4 5 W During operation approx 7 W Index A PACU ATON ariei aaia 10 Authorisation 0 005 24 B Base station 00 12 Belles see erence ean 3 7 9 10 15 Bell transformer 9 10 Bottom doorbell key 13 C Call diversion 2 14 17 18 activating deactivating 14 diversion destination 14 operating the door intercom 18 setting up to an external number 14 Statusa aks amp Mowe ee cel ecw can 18 Call time cadet ti awaits 15 Calling the door intercom from an internal user 17 CE symbol sc pee eae hy eet Shs 23 Changing the display language 12 Changing the PIN 13 Clamping plug 055 8 Cleaning as Wi ews 22 Compatible Gigaset cordless telephones 23 Connecting entry lighting 11 Control unit a oa auauua aana ana 7 12 connecting 000eeeeeee 10 connecting entry lighting 11 LE De ics Beat Bitte d Pate eee 12 light kri nr eae hee aches 11 mounting 00ee eee 9 radio range e eee eee 9 terminal cap
29. rbell It is suitable for mounting outdoors and features weatherproof protection Loudspeaker Top key ni Bottom key m Microphone Make sure that there are no power sup ply lines cables or the like near the mounting location Select the attachment and mounting location so that there is a minimum dis tance of 10 cm between the micro phone and the closest wall surface min 10 cm min 10 cm Installing the Gigaset HC 450 door intercom system Surface mounting Remove the bell button if there is one and unscrew the cables Fit the frame over the cable outlet Next screw one of the enclosed green clamping plugs to the existing 2 core bell cable polar ity is not relevant here and insert it in the jack with the ETS symbol green jack Caution If you are using the existing bell cable the doorbell system must be set to zero potential prior to installation Caution Cables must not be connected or disconnected during a thunderstorm Hang the door intercom at the top of the frame 45 degree angle see illus tration on right and lower it against Connecting a door opener optional the wall Fix the door intercom using 7 the two enclosed hexagon socket The door opener is connected to the STANE appropriate jack of the door intercom using a 2 core cable and the blue clamping plug Door intercom Control unit Light Actuator ETS oaoa io Re A
30. rded to all internal users or gt Ringer Tone gt A The current setting is displayed Select the desired ringer tone call melody 1 10 or special GHC melody Press the display key continue with Press and hold return to idle status Note If Call All is set and different handset types are being used the call melodies of the individual handsets can differ Making settings for the bottom doorbell key You have four options here 1 As Upper Key setting as for first door call The function of the two keys is then identical 2 Second Door Call You can select an other internal user and different tone dialling if necessary 13 Setting up the Gigaset HC450 door intercom system 3 Light You can use the doorbell key to control the entry lighting as an alterna tive to the Door Call The lighting sys tem must be connected to the control unit for this purpose 4 No Function Call up the menu for the settings see p 12 gt Lower Door Key gt id The current setting is displayed Select the mode for the bottom key Second Door Call Light or No Function EA Press the display key continue with Press and hold return to idle status Proceed as described in the section Making settings for the top doorbell key see p 13 to set the internal call destination and ringer tone The only difference is In the menu for the door intercom se
31. re com mencing registration Following successful registration Intercom will appear in the list of inter nal users This preset name can be changed via the handsets refer to the user guide for the handset 12 Note Change the system PIN of the base station once more refer to the manual for your tele phone This ensures among other things that only designated handsets can be regis tered with the base station Setting functions Starting programming Call up the menu for the door intercom settings This initial programming step is always the same for all functions to be set Note The menu for changing the display language is called up automatically during startup see p 12 Initiate an internal call and select the internal user Intercom Tas Press the talk key BME Press the display key Enter the 4 digit system PIN of the door intercom if the PIN has been changed from the delivery version 0000 and press o You are now in the menu in which you can make settings for the door intercom Changing the display language You can view the display texts in different languages The languages available include English German Italian Dutch and French Call up the menu for the settings see p 12 gt Language gt Gd The current setting is displayed English Select the desired language for example English and press od Press and hold return to idle
32. requirements have been taken into consideration We Siemens Home and Office Communication Devices GmbH amp Co KG declare that this device meets the essential requirements and other relevant regulations laid down in Directive 1999 5 EC A copy of the 1999 5 EC Declaration of Conformity is available at this Internet address http www siemens com gigasetdocs C 0682 Guarantee Certificate United Kingdom Without prejudice to any claim the user customer may have in relation to the dealer or retailer the customer shall be granted a manufacturer s Guarantee under the conditions set out below In the case of new devices and their components exhibiting defects result ing from manufacturing and or mate rial faults within 24 months of pur chase Siemens shall at its own option and free of charge either replace the device with another device reflecting the current state of the art or repair the said device In respect of parts subject to wear and tear including but not lim ited to batteries keypads casing this warranty shall be valid for six months from the date of purchase This Guarantee shall be invalid if the device defect is attributable to improper treatment and or failure to 24 comply with information contained in the user guides This Guarantee shall not apply to or extend to services performed by the authorised dealer or the customer themselves e g installation configu ration sof
33. stomer Devices fitted with accessories not authorised by Siemens To invoke this Guarantee please contact the Siemens helpdesk on 1850 777 277 This number is also to be found in the accompanying user guide 25 Appendix Technical Data HC450 control unit RF standard DECT HC450 door intercom Operating temperature 20 C to 55 C Storage tempera ture 25 C to 70 C Storage tempera ture 25 C to 70 C Dimensions of the housing for surface mounting 185 x 150 x 30 mm LxWxD Weight 1 1 kg with mains adapter Protection class to DIN IP40 Loading capacity of Actuator the switching con max 30 V 1 A 30 VA tacts relays Light 230V max 5A Maximum conduc 15 m tor length between control unit and door intercom Colour Grey 26 Mains adapter Range Up to 300 m outdoors Transport 25 C to 55 C Up to 50 m indoors temperature Number of 60 duplex channels Dimensions Door station cover channels 215 x 98 x 30 mm LxWxD Radio frequency 1880 1900 MHz Frame for surface range mounting 210 x 93 mm LxW Duplex procedure Time multiplex 10 ms frame length Weignt 3609 Channel spacing 1728 kHz Molete protec yeas Bit rate 1152 kbps Output 12VAG 1A Modulation GFSK voltage door opener Voice coding 32 kbps B Colour Silver Transmit power 10 mW ave
34. tee shall not apply to or extend to services performed by the authorised dealer or the customer themselves e g installation configu ration software downloads User manuals and any software supplied on a separate data medium shall be excluded from the Guarantee The purchase receipt together with the date of purchase shall be required as evidence for invoking the Guarantee Claims under the Guarantee must be submitted within two months of the Guarantee default becoming evident Ownership of devices or components replaced by and returned to Siemens shall vest in Siemens This Guarantee shall apply to new devices purchased in the European Union For Products sold in the Republic of Ireland the Guarantee is issued by Siemens Home and Office Communica tion Devices GmbH amp Co KG Schlaven horst 66 D 46395 Bocholt Germany Any other claims resulting out of or in connection with the device shall be excluded from this Guarantee Nothing in this Guarantee shall attempt to limit or exclude a Customers Statutory Rights nor the manufacturer s liability for death or personal injury resulting from its negligence The duration of the Guarantee shall not be extended by services rendered under the terms of the Guarantee Insofar as no Guarantee default exists Siemens reserves the right to charge the customer for replacement or repair The above provisions does not imply a change in the burden of proof to the detriment of the cu
35. ttings select the entry Low Key Setting instead of Upper Door Key Setting up a call diversion to an external number You can set up the call diversion using the following programming steps Caution Note that you can very easily activate or deac tivate the call diversion from your handset When you are at home set the door intercom to Status Home The incoming calls from the door intercom will then be sent to your inter nal handset When you are leaving the house set the door intercom to Status Away The incoming calls will then immediately be routed to your external diversion destination Refer to the chapter Operation with automatic call diversion p 18 to find out how to make the switch The external call diversion destination relates only to the top doorbell key 14 Setting the destination for automatic call diversion to an external number You can divert incoming calls from the door intercom to an external number To do this you must first enter the destina tion number Call up the menu for the settings see p 12 gt Diversion No gt A Si Enter the number max 20 characters for the external call diversion and press fe The setting is saved Press and hold return to idle status Caution Don t forget the zero for a trunk line if applica ble If you do not enter a number for the external call forwarding automatic call diversion to an external number will b
36. tware downloads User guides and any software supplied ona separate data medium shall be excluded from the Guarantee The purchase receipt together with the date of purchase shall be required as evidence for invoking the Guarantee Claims under the Guarantee must be submitted within two months of the Guarantee default becoming evident Ownership of devices or components replaced by and returned to Siemens shall vest in Siemens This Guarantee shall apply to new devices purchased in the European Union For Products sold in the United Kingdom the Guarantee is issued by Siemens Home and Office Communica tion Devices GmbH amp Co KG Schlaven horst 66 D 46395 Bocholt Germany Any other claims resulting out of or in connection with the device shall be excluded from this Guarantee Nothing in this Guarantee shall attempt to limit or exclude a Customers Statutory Rights nor the manufacturer s liability for death or personal injury resulting from its negligence The duration of the Guarantee shall not be extended by services rendered under the terms of the Guarantee Insofar as no Guarantee default exists Siemens reserves the right to charge the customer for replacement or repair The above provisions does not imply a change in the burden of proof to the detriment of the customer To invoke this Guarantee please contact the Siemens telephone service The rele vant number is to be found in the accom pan
37. ying user guide Guarantee Certificate Ireland Without prejudice to any claim the user customer may have in relation to the dealer or retailer the customer shall be granted a manufacturer s Guarantee under the conditions set out below In the case of new devices and their components exhibiting defects result ing from manufacturing and or mate rial faults within 24 months of pur chase Siemens shall at its own option and free of charge either replace the device with another device reflecting the current state of the art or repair the said device In respect of parts subject to wear and tear including but not lim ited to batteries keypads casing this warranty shall be valid for six months from the date of purchase This Guarantee shall be invalid if the device defect is attributable to improper care or use and or failure to comply with information contained in the user manuals In particular claims under the Guarantee cannot be made if The device is opened this is classed as third party intervention Repairs or other work done by persons not authorised by Siemens Components on the printed circuit board are manipulated The software is manipulated Defects or damage caused by dropping breaking lightning or ingress of mois ture This also applies if defects or dam age was caused by mechanical chemi cal radio interference or thermal fac tors e g microwave sauna etc Appendix This Guaran
Download Pdf Manuals
Related Search