PCI8250 User`s Manual
Contents
1. Check the shipping carton for any damage If the shipping carton and contents are damaged notify the local dealer or sales for a replacement Retain the shipping carton and packing material for inspection by the dealer Check for the following items in the package If there are any missing items contact your local dealer or sales gt PCI8250 Data Acquisition Board ART Disk a user s manual pdf b drive c catalog Warranty Card FEATURES Analog Output Output Range 0 5V default 0 10V 2 5V 5V 10V 16 bit resolution Update Rate 100 KHz single channel Set up Time 600nS 0 01 Channel No 8 channel isolated sync output Isolated voltage 2500Vrms 1 min Input impedance 50Q Sync Source software hardware Trigger Dir rising edge trigger falling edge trigger Data transmission mode program mode VV VV VV VV Y ON WV Support multi card synchronization at most 4 cards Other features Board Clock Oscillation 40M Hz PCI8250 Data Acquisition Chapter 2 Components Layout Diagram and a Brief Description 2 1 The Main Component Layout Diagram RP3 RP5 RP7 RP9 p RP RPI1 RP13 RP2 RP4 RP6 RPS RP10 RP12 JTTTJT33TTT L l GN L aa ay m rig gx Th rl o LI 31 m 4HHIHHOHHH Hf REWRRWRRARRRTARARRRREM Lia e Kf sess H e CNI c OL MTM o trn xc p sans m tee IIZIIIITITIIIIT i i t A 7 TL Hu NU HTTHHTHTHT FR far 0 mu 4 P2 TE 4 P32. nmm ntt TRUTH et Fai gods cs aft qo ml IFFEEEEHTEEHEEEHEEEEEEE bear Mm am 134444 TF 41 P4 U al 8 d Q n To gt B 2 2 The Function Description for the Main Component 2 2 1 Signal Input and Output Connectors CNI Analog signal output connector P1 Sync pulse signal input external trigger P2 P4 Sync pulse signal output 2 2 2 Potentiometer RP11 AOO analog output full scale adjustment potentiometer RP12 AOI analog output full scale adjustment potentiometer RP7 AO2 analog output full scale adjustment potentiometer RP8 AO3 analog output full scale adjustment potentiometer RP5 AO4 analog output full scale adjustment potentiometer RP6 AOS analog output full scale adjustment potentiometer RP2 AO6 analog output full scale adjustment potentiometer PRI AO7 analog output full scale adjustment potentiometer PR10 AOO AOI analog output zero point adjustment potentiometer PR9 AO2 AO3 analog output zero point adjustment potentiometer PR4 AO4 AOS5 analog output zero point adjustment potentiometer BUY ONLINE at art control com englishs or CALL 86 10 51289836 CN 4 PCI8250 Data Acquisition PR3 AO6 AO7 analog output zero point adjustment potentiometer RP13 analog output signal 5V reference voltage adjustment 2 2 3 Physical ID of DIP Switch DIDI Set physical ID number When the PC is installed more than one PCI8250 you can use the DIP switch to set a physical ID number fo
3. and Warranty Policy occcccccccccccccccccseseeeeeeeeeeeeeee cece cence ett hee nenne eese sssssss nni rrr n FD DL e esses snas nnns 10 SS III 10 6 2 Analog Signal Outp t Calibration RE se CN FF FY FN FN FRON NON NN NON 10 G S Ward ge Pole i a a a i YNN NN 10 Products Rapid Installation and Self check iui iie eeeeseseseeesee enhn etu AEN rara AE A EA sopore 11 jo a a aaO ee ee ne ee ee ee ee ee ee ee ee eee ee ee NDE 11 Ro iL 6 E RE RE RE N FEN FERN FEN FN FF RR NF FD AEE NAE N 11 Delete WIGHP Inst ol AE LG O YR CO NO RO NO ea er eet tpe HA 11 PCI8250 Data Acquisition Chapter I Overview In the fields of Real time Signal Processing Digital Image Processing and others high speed and high precision data acquisition modules are demanded ART PCI8250 data acquisition module which brings in advantages of similar products that produced in china and other countries is convenient for use high cost and stable performance ART PCI8250 is an analog output module based on PCI bus It can be directly inserted into IBM PC AT or a computer which is compatible with PCI8250 to constitute the laboratory product quality testing center and systems for different areas of data acquisition waveform analysis and processing It may also constitute the monitoring system for industrial production process Unpacking Checklist
4. 250 Data Acquisition Chapter 3 Signal Connectors 3 1 The Definition of Signal Input and Output Connectors 62 core plug on the CNI pin definition 19 AOO AGND 37 __ 18 AO AGND 36 17 AO2 AGND 9 16 AO3 AGND 34 15 AO4 AGND 33 14 AO5 AGND 32 JU AO6 AGND 3l m AO7 AGND 30 J 11 NC AGND 29 9i AGND 28 E G NC AGND 27 l u NC AGND 26 o 7 NC AGND 25 si 6 NC AGND 24 5 NC AGND 23 z 4 NC AGND 22 a 3 NC NC 2 J E P NC NC 20 gt l NC Pin definition AO0 AO7 Analog signal output pins the reference ground is AGND AGND Analog signal ground NC Notcomnected o O PCI8250 Data Acquisition Chapter 4 Connection Wavs for Each Signal 4 1 Analog Output AOO analog signal AOI C3 e AO7 device device AGND NW Figure 4 3 analog signal output connection 4 2 Sync pulse Trigger Signal Input 4 3 Sync pulse signal output CLKOUTI gt CLKOUT2 CLKOUT3 nn 716 T DGND L PCI8250 Data Acquisition 4 4 Methods of Realizing the Multi card Svnchronization Three methods can realize the synchronization for the PCI8250 the first method is using the cascade master slave card the second one is using the common external trigger When using master slave cascade card programs the master card generally uses the internal clock source model while the slave card uses the exter
5. PCI8250 User s Manual O Beijing ART Technology Development Co Ltd PCI8250 Data Acquisition Contents CONCETTA d POT E R f PM 2 o aa a VEIT L 3 Chapter 2 Components Layout Diagram and a Brief Description ssssssesnnnnnznnnnnnnnnnzznnnnnnznznnzzzzzzntenznznnzzzznnannnnznnnznana 4 2 1 The Main Component Layout Diagram l nnns asas NEEE 4 2 2 The Function Description for the Main Component eeesesseeeeseseeeeeeee eniin ananas 4 2 2 1 Signal Input and Output Connectors ccc cccceessssseseeeeseeseeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 4 ED EEO BU OD A 4 22 Pi e il TU uod 0 GRH NO NC Y eee 5 CHODI O O U NC OC OY is ii A RD i CR Y YT FE DON WT DEN a di DON 6 3 1 The Definition of Signal Input and Output Connectors s e eeeeeeennnnnnnznzznzznznznnzznnzzzzznnnnnnnanazzzanzznnnnzanazznnnzannnzza 6 Chapter 4 Connection Ways Jor Each SIBNA isssssezsiarizniitaikiisiee kabina ki l g b a Tie 1 a PHM FOUN l a A M E NN NR 7 4 2 Syne pulse d Ba or ded Ue l DROITE 7 4 5 SVM plc simal DEDE EST FFY FF HF 8 00 6 7 4 4 Methods of Realizing the Multi card Synchronization sess III LIII 1000 8 Chapter 2 The Instruction of Trigger P WICHlQni aeacautenscoxesie ee ti iksi i eue e aei ubupe a eu eun ulpa eus eu sube pe pue eade rea bp Nas 9 Chapter 6 Notes Calibration
6. dard testing procedure Based on the specification of Pin definition connect the signal acquisition data and test whether AD is normal or not Connect the input pins to the corresponding output pins and use the testing procedure to test whether the switch 1s normal or not Delete Wrong Installation When you select the wrong drive or viruses lead to driver error you can carry out the following operations In Resource Explorer open CD ROM drive run Others SUPPORT gt PCI bat procedures and delete the hardware information that relevant to our boards and then carry out the process of section I all over again we can complete the new installation
7. ea APPETT X MA IEC T ICT TE TOTO TIT T OTT HR The first falling edge after the the D A started is invalid i D A started is valid Figure5 1 Falling edge trigger When ADPara TriggerDir PCI8250 TRIGDIR POSITIVE we can achieve rising edge trigger Whenever a rising edge occurs on CLKIN the D A begins to work The following CLKIN has no effect on analog output PCI8250 Data Acquisition Chapter 6 Notes Calibration and Warranty Policy 6 1 Notes In our products packing user can find a user manual a PCI8250 module and a quality guarantee card Users must keep quality guarantee card carefully if the products have some problems and need repairing please send products together with quality guarantee card to ART we will provide good after sale service and solve the problem as quickly as we can When using PCI8250 in order to prevent the IC chip from electrostatic harm please do not touch IC chip in the front panel of PCI8250 module 6 2 Analog Signal Output Calibration In the manual we introduce how to calibrate PCI8250 in 10V calibrations of other output ranges are similar 1 Zero adjustment Select AOO connect a DC voltage source with value equal to OV to AOO Adjust RP10 until the actual output value 0 000V 2 Full scale adjustment Select AO0 connect a DC voltage source with value equal to 10000mV to AIO Adjust RP5 until the input value 9999 69mV 3 Repeat steps above until meet the requirement 6 3 Wa
8. nal clock source mode After the master card and the slave card are initialized according to the corresponding clock source mode At first start all the slave cards as the main card has not been activated and there is no output clock signal so the slave card enters the wait state until the main card was activated At this moment the multi card synchronization has been realized When you need to sample more than channels of a card you could consider using the multi card cascaded model to expand the number of channels Master Card CLKIN gt Slave Card 1 Slave Card 2 When using the common external trigger please make sure all parameters of different PCI8250 are the same input triggering signal from CLKIN pin then click Start button at this time PCI8250 does not output any signal but waits CLKOUT for external trigger signal When all modules are waiting for external trigger signal use the common external trigger signal to startup modules See the following figure External Trigger signal rem OR PCI 8250 CLKIN gt PCI 8250 Y__CLKIN PCI 8250 PCI8250 Data Acquisition Chapter 5 The Instruction of Trigger Function When ADPara TriggerDir PCIS250 TRIGDIR NEGATIVE we can achieve falling edge trigger Whenever a falling edge occurs on CLKIN the D A begins to work The following CLKIN has no effect on analog output D A Start Pulse CLKIN trigger signal Qessteesss ese o oss t
9. not entitled to our service 4 Customers are responsible for shipping costs to transport damaged products to our company or sales office 5 To ensure the speed and guality of product repair please download an RMA application form from our company website BUY ONLINE at art control com englishs or CALL 64861583 CN 10 PCI8250 Data Acquisition Products Rapid Installation and Self check Rapid Installation Product driven procedure is the operating system adaptive installation mode After inserting the disc you can select the appropriate board type on the pop up interface click the button driver installation or select CD ROM drive in Resource Explorer locate the product catalog and enter into the APP folder and implement Setup exe file After the installation pop up CD ROM shut off your computer insert the PCI card If it is a USB product it can be directly inserted into the device When the system prompts that it finds a new hardware you do not specify a drive path the operating system can automatically look up it from the system directory and then you can complete the installation Self check At this moment there should be installation information of the installed device in the Device Manager when the device does not work you can check this item Open Start gt Programs gt ART Demonstration Monitoring and Control System gt Corresponding Board 7 Advanced Testing Presentation System the program is a stan
10. r each board which makes it very convenient for users to distinguish and visit each board in the progress of the hardware configuration and software programming The following four bits numbers are expressed by the binary system When DIP switch points to ON that means 1 and when it points to the other side that means 0 As they are shown in the following diagrams ID3 is the high bit IDO is the low bit and the black part in the diagram represents the location of the switch Test softwares of the company often use the logic ID management equipments and at this moment the physical ID DIP switch is invalid If you want to use more than one kind of the equipments in one and the same system at the same time please use the physical ID as much as possible ID3 ID2 IDI IDO ID3 ID2 IDI IDO ID3 ID2 IDI IDO on ON an ON T _ n omi 1 2 3 4 i 2 3 4 The above chart shows 1111 so it means that the physical ID is 15 The above chart shows 0111 so it means that the physical ID is 7 The above chart shows 0101 so it means that the physical ID is 5 lor or or or 0 90 Forma oru ori ona 1 i Forma oru ona orol 2 2 Forma oru ovp Tow 3 3 Form ona or for 4 4 Forma ona or ona s s Forma Pow o or 6 e Fon ore ori forr s as To ori or ona 9 Pon or Pow ovip B uu Fomm few for wa p un PCI8
11. rranty Policy Thank you for choosing ART To understand your rights and enjoy all the after sales services we offer please read the following carefully 1 Before using ART s products please read the user manual and follow the instructions exactly When sending in damaged products for repair please attach an RMA application form which can be downloaded from www art control com 2 All ART products come with a limited two year warranty The warranty period starts on the day the product is shipped from ART s factory For products containing storage devices hard drives flash cards etc please back up your data before sending them for repair ART is not responsible for any loss of data Please ensure the use of properly licensed software with our systems ART does not condone the use of pirated software and will not service systems using such software ART will not be held legally responsible for products shipped with unlicensed software installed by the user 3 Our repair service is not covered by ART s guarantee in the following situations Damage caused by not following instructions in the User s Manual Damage caused by carelessness on the user s part during product transportation Damage caused by unsuitable storage environments 1 e high temperatures high humidity or volatile chemicals V Y V VY Damage from improper repair by unauthorized ART technicians gt Products with altered and or damaged serial numbers are
Download Pdf Manuals
Related Search