STEINER Military 5-25 × 56 mm
Contents
1. and take a quick glance through the scope If the reticle appears sharp and black no further adjustment is necessary PA lf not use quick glances through the scope while rotating the focus ring until the reticle pattern is sharp and clear NOTE Do not look through the eyepiece as you turn the focus ring Your eyes will adjust to the out of focus condition PARALLAX FOCUS ADJUSTMENT Parallax is the apparent movement of the reticle in relation to the target when the eye is not directly in line behind the center of the scope Images from different distances focus in front of or behind the scope s reticle Parallax is more noticeable with higher magnification scopes and scopes with a larger objective lens To use the parallax focus adjustment ro tate the knob on the left side of the adjustment turret until the numeral corresponding to the known target distance lines up with the refer ence mark If the distance is unknown rotate the adjustment knob until the target image is sharply focused When the scope is set parallax free for the distance you are viewing you should be able to move your eye side to side or up and down without seeing the reticle move appreciably in relation to the target WINDAGE ELEVATION ADJUSTMENT The windage and elevation knobs are de signed for precise adjustment The dials are calibrated so that 1 click 0 1 MRAD The windage knob located on the right side of the tube is calibrat2. be retracted Reinstall the knob and keep in mind to po sition the two screws at 3 and 6 o clock Press the knob firmly against the air resis tance on the scope and tighten the screws again ILLUMINATED RETICLE ADJUSTMENT The STEINER Military Riflescope fea tures an illuminated reticle that makes it easier to see the reticle in low light condi tions The intensity of the illumination is controlled by the rotary illumination switch located on the left side of the adjustment tur ret The switch has 11 intensity levels and a battery saver position in between each level that turns off the illumination The Off positions at the minimum and maximum ranges turn the circuit off com pletely and should be used when the scope is not in use Each level also has a detent to prevent unintended changes during use Positions 8 11 are for daylight opera tions Positions 1 7 are used during night time operations Positions 1 4 are suitable when utilizing night vision devices The reticle is powered by a 3 volt lithium cell battery CR2450 To install a new bat tery simply unscrew the battery cap on the rotary switch and install the new battery flat side up It is advisable to remove the bat tery for long term storage over a month MOUNTING THE SCOPE The riflescope requires 34 mm rings STEINER recommends using high quality solid steel rings and bases Quality compo nents ensure that your scope
3. will remain securely mounted and will provide the maxi mum accuracy Steiner recommends the use of a 45MOA 13 1 mRAD mount if shooting at extremely long range where the maximum elevation of 26 mRAD is required Read the manufacturer s directions regarding the in stallation of mounts and rings ACCESSORIES STEINER offers a range of accessories for this scope The objective lens is designed to accommodate standard anti reflective de vices sunshades filters and other accesso ries that fit a 58x0 75mm objective CARE amp MAINTENANCE This STEINER Military riflescope is fully waterproof and fogproof To protect the ob jective and ocular lenses it comes equipped with flip up scope caps In the event that the lenses are subjected to dust dirt or mud fol low these steps to clean and protect the lens surface Failure to remove grit before cleaning will damage the lens surface Coarse dirt debris must be removed from the lens surface Position the scope so par ticles will fall away from the lens and then use a soft brush to gently whisk away the de bris while blowing on the lens to dislodge the particles For heavy dirt like dried mud use a spray of clean water or lens cleaning fluid to remove the dirt Your STEINER riflescope will provide reli able performance given reasonable care and treatment All moving assemblies are perma nently lubricated Only occasional cleaning of the outside of the scope and the exteri
4. STEINER ERM AN Y STEINER Military 5 25x56 mm USER S MANUAL 2 2 3 3 6 7 7 7 8 7 0 1 CONTENTS Introduction Eyepiece Focusing Parallax Adjustment Windage Elevation Adjustment Illuminated Reticle Adjustment Mounting the Scope Accessories Care amp Maintenance Reticle Reticle Subtensions Specifications Scope Dimensions INTRODUCTION STEINER is one of the largest manu facturers of high quality optics in the world STEINER products represent the highest level of precision and technology STEINER Military Scopes were espe cially developed in close cooperation with in ternational weaponry experts for the tough requirements of military missions around the world They are field tested and combat proven by special forces and and successfully withstand the harshest conditions STEINER Military Riflescopes represent a new class in terms of performance quality and reliability They are ideally suited for tactical military and law enforcement operations This manual outlines the basic operation and maintenance of the scope Elevation Adjustment Knob ens a Rotary Illumination Dial Eyepiece Focus Ring Windage Adjustment Knob Power Ring EYEPIECE FOCUSING The eyepiece can be focused so that the reticle appears sharp and black to your eyes Adjusting the focus is quick and easy to do Just follow this procedure El Point the scope at the sky or a plain wall
5. ed for up to 6 mRAD of adjustment left and right Adjustments are indicated by detents and audible clicks Hard stops at both ends of the adjustment range prevent shooters from getting lost on the dial For shooting at extreme distances the elevation knob offers up to 26 mRAD and two full revo lutions of ad justment The indication occurs through a patented double scale The first revolution of 149 clicks are indicated on a rotating scale When turning past 149 clicks the scale disappears to the top and a second scale ranging from 150 to 260 klicks appears from below This riflescope is shipped from the factory with the op tical center knob at 0 position set below center With out tapered bases a 4 the initial sight in or bore sighting will likely produce an initial point of im pact considerably high Because of the Zero Stop feature as shipped from the UP 4 factory the scope has ln no immediate capa zz 4 bility for downward point of impact ad justment STEINER offers this riflescope with a choice of windage el evation knobs that offer both Clockwise and Counterclockwise adjustment Use the fol lowing procedure whenever you need down ward point of impact adjustment up wt teeta x El Turn the elevation adjustment knob clock wise to 0 Steps 2 5 below are for scopes with clockwise windage elevation adjustment For counter clockwise knobs ju
6. or lens es is required Never disassemble your scope Disas sembly by anyone other than the manufacturer will void the warranty If you have any other problems with the STEINER riflescope return it to the factory for repair For further information please visit our web site at www steiner military com G2B MIL DOT ILLUMINATED RETICLE G2B MIL DOT RETICLE SUBTENSIONS pas MSR RETICLE MSR RETICLE SUBTENSIONS Je ER BES Eee Pa SPECIFICATIONS MILITARY 5 25x56 mm O bj e Dlze m BERATEN Change FOV 100m gt 7 23 1 43 m Tg Factor Tube Diameter 34 mm Reticle G2B Mil Dot MSR Cs ee Water Pressure Proof upto 10m 100 Fog Proof Inside yes nitrogen filled Storao je T emperature 35 C 70 C Weight with caps without caps lt 1030 g 1000 g Inzramn ni ICFEMent ER Range 60 cm 6 0 mrad 10 SCOPE DIMENSIONS EEE CC LT A Optimum Eye RENE High Low 90 5 T z 62 2 44 17 E Scope Dimension 22 16 61 ScopeDimensin e 1 24 I Scope Dimension 99 J Scope Dimension 6 46 Bm Bu a I o gt pe 11 STEINER OPTIK GmbH Dr Hans Frisch Str 9 95448 Bayreuth GERMANY Phone 49 921 7879 0 Fax 49 921 7879 88 E Mail military steiner de Item N
7. st reverse the indicated direction EJ Use the hex wrench supplied with the scope to loosen the set screw half turn only on the elevation adjustment knob located just below the top of the knob EJ Pull up slightly on the adjustment knob to the second white hash mark on the turret Turn the knob clockwise slightly more than the number of mils needed to achieve zero A Retighten the set screws Adjust the eleva tion down the required amount EJ Once the elevation adjustment is complete once again loosen the two set screws and reset the knob to 0 With the screws loose push down firmly on the knob until it is fully seated on the turret base and then retighten the set screws NOTE When retightening set screws on eleva tion knob maintain pressure on the top of cap to ensure proper seating of adjustment dial ATTENTION It is recommended not to remove the elevation adjustment knob If the knob is removed it is possible to rotate the Rotation Indicator actuator which controls the eleva tion rotation indicator pin to a position which will prevent full rotation of the knob when reinstalled Ifthe knob locks up in the middle of the two turns the Rotation Indi cator actuator is out of position When this occurs return the knob to 260 loosen the set screws and remove the cap exposing the actuator Rotate the ac tuator fully counter clockwise until it stops against the adjacent plate The Rotation Indi cator pin will
8. umber V0000266 www steiner military com BERETTA DEFENSE TECHNOLOGIES Your First Line of Defense f DD iit DBERETTA Benelli sako STEINERMA GERMANY www berettadefensetechnologies com
Download Pdf Manuals
Related Search