Manual - Microh
Contents
1. Fixture One Power Cord One Bracket Set One User Manual One 2 Safety Instructions CAUTION ELECTRIC SHOCK WARNINGI USE EXTREME CAUTION WHEN HANDLING WIRES This device has left the factory in perfect condition In order to maintain this condition and to ensure safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems If the device has been exposed to temperature changes do not switch it on immediately The arising condensation could damage the device Leave the device switched off until it has reached room temperature and is dry This device falls under protection class therefore it is essential that the device be grounded The electrical connection must be carried out by a qualified technician The device should only be used with rate voltage and frequency Make sure that the available voltage is not higher than 120V as stated at the end of this manual Make sure the power cord is never crimped or damaged in any way as this could cause shock and damage If your power chord is damaged in any way please purchase a new cable from your local MICROH dealer Always disconnect power when the device is not in use or before cleaning it Never pull out the plug by tugging2. 35 C VOLTAGE 120VAC 60Hz 60W 0 5A FUSE 120VAC 1A DIMENSIONS 9 01 x 6 97 x 3 54 230 x 177 x 90 mm BOX DIMENSIONS 13 98 x 8 46 x 6 42 355 x 215 x 163 mm NET WEIGHT 5 95 Ibs 2 7 kgs GROSS WEIGHT 8 75 Ibs 3 97 kgs WARRANTY 2 Year Limited Warranty The Laser diodes are covered under a 6 month replacement warranty 5 71 145 mm 3 15 80 mm SPITFIRE RGY 3 54 90 mm 6 97 177 mm 9 01 230mm 9 MAINTENANCE AND CLEANING The following points have to be considered during the inspection 1 All screws for installing the device or parts of the device must be tightly connected and must not be corroded 2 There must not be any deformations on the housing colour lenses fixations or installation spots ceiling suspension trussing 3 Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances 4 The electric power supply cables must not show any damage material fatigue or sediments Further instructions depending on the installation spot and usage must be handled by a skilled installer or technician Any safety issues must be resolved CAUTION DISCONNECT POWER BEFORE SERVICING In order to keep the fixture in good condition and extend the life we suggest regular cleaning to the fixture 1 Clean the inside and outside lens each week to avoid the light output from darkening due to accumulation of dust dirt etc 2 Clean the fan each week
3. IVIC ARCI PROFESSIONAL PRODUCTS Www mICronpro com m a a USER MANUAL SPITFIRE RGY Keep this manual for future reference TABLE OF CONTENTS 1 INTRODUCTION AND UNPACKING 1 2 SAFTEY INSTRUCTIONS 1 2 3 OPERATION INSTRUCTIONS 2 3 4 MOUNTING AND INSTALLATION 3 4 5 DMX 512 CONTROL CONNECTIONS 5 6 DMX CHANNELS 6 7 KEY FEATURES 7 8 TECHNICAL SPECIFICATIONS 7 9 MAINTENANCE AND CLEANING 8 1 INTRODUCTION AND UNPACKING Thank you for purchasing the MICROH SPITFIRE RGY laser system For your own safety and knowledge please read this manual before installing or operating the device This manual covers the important information on installation and applications Please install and operate the fixture according to instructions Meanwhile please keep this manual for future reference The MICROH SPITFIRE RGY laser is made of a new type of high temperature cast aluminum casing The fixture is designed and manufactured strictly following CE standards complying with international standard DMX512 protocol This fixture is applicable but not limited to large scale live performances theater studio nightclubs and discos The MICROH SPITFIRE RGY laser system uses 2 coloured laser diodes that are carefully aligned with the internal scan mirrors Please carefully unpack it when you receive the fixture and check if it was damaged during the transportation And please check whether the following items are included inside the box
4. 3 A detailed electrical check by approved technician every three months is advised Ensure the circuit contacts are in good condition and prevent from overheating We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents There are no serviceable parts inside the device Please refer to the instructions under Installation instructions Should you need any spare parts please order genuine MICROH parts from your local dealer IF YOU SHOULD EXPERIENCE ANY PROBLEMS OR ISSUES PLEASE CONTACT MICROH PROFESSIONAL PRODUCTS BY EMAIL AT info microhpro com In the event that your unit is defective in any way please contact your local dealer to obtain an RA number for service repair DISCLAIMER MICROH believes that the information contained within this user manual is accurate However Microh is not responsible for any error or addendums to this manual If you have any comments or general suggestions on how this manual can be improved please contact info microhpro com Thank you PROFESSIONAL PRODUCTS www microhpro com
5. ach the safety chain and ensure the screws are properly screwed in when installing the fixture Make sure the lens is in good condition It is recommended to replace the unit if there are any damages or severe scratches Make sure the fixture is operated and installed by qualified personnel Keep the original packaging in case of defective product Any non manufacturer additions modifications or changes in any way will void all warranty Please do not attempt to open unit It is only to be serviced by an authorized technician If this occurs or is apparent the warranty will be voided The fixture s warranty will be voided if there are any malfunctions from not following the user manual or any illegal operation shock short circuit electronic shock lamp broke etc DIPSWITCH CHART DIP SWITCH CHART X ani on came FUNCTION SET DMX ADDRESS FOR DMX MODE DIP SWITCH 1 9 m DMX Slave DMX MODE Before using the DMX512 controller the channel address should be set It can be set 001 511 Every binary address switch has a digital number Please refer to chart below ILDA PC CONTROL MODE To run the SPITFIRE RGY in IDLA mode or PC CONTROL MODE simply connect your ILDA signal cable to the DB25 jack located on the rear of the unit and the unit will automatically recognize NOTE when ILDA is connected it supersedes all modes 4 MOUNTING AND INSTALLATION Caution For added protection mount the fixtures in a
6. e fixture provides a built in rigging point for a safety cable on the hanging bracket as illustrated above Be sure to only use the designated rigging point for the safety cable and never secure a safety cable to a carrying handle Please see picture below 5 DMX 512 CONTROL CONNECTIONS This fixture complies with international USITT DMX standards and can be used with either a 3 pin or 5 pin DMX connector Plug in the provided 3 pin XLR cable to the female 3 pin XLR output of your controller and the other side to the male 3 pin XLR input of the MICROH SPITFIRE RGY To connect the units to DMX you must daisy chain the fixtures together as referred in the diagram below Always end your DMX 512 connection with a DMX terminator DMX OUTPUT CONTROLLER FIXTURE 1 FIXTURE 2 FIXTURE 3 _ X x X X X X UPTO 30 UNITSIN MASTER SLAVE MODE S NS SS SS x R LALLA LA 7 XLR CABLE XLR CABLE XLR CABLE DMX Output DMX Input 3 Pin XLR Socket 3 Pin XLR Socket COMMON K meas DMX512 OUT o me DMX512 IN 3 Data SPIN XLR 3 PIN XLR For installations where the DMX cable has to run a long distance or is in an electrically noisy environment it is recommended to use a DMX terminator This helps in preventing corruption of the digital control signal by electrical noise The DMX terminator is simply an XLR plug with a 120 Q resistor connected between pins 2 and 3 which is then plugged into the output XLR socket of the last fixture i
7. n the chain Please see illustrations below 1202 2 1 PIN3 PIN 2 6 DMX CHANNELS me omen 70 139 Sound Active Control Channel 1 Control mode 0 33 Static Pattern Channel 2 Pattern Selection 34 255 Dynamic Geometric pattern Channel 4 Spot amp Line 0 255 Line to Spot Effect Horizontal 161 190 Left to Right Movement Channel 5 Movement 191 220 Right to Left Movement 221 255 Right and Left In phase Movement 461 190 Down to Up Movement Slow to Ch 16 Vertical Fast anne Movement Up to Down Movement Slow to 191 220 Fast 221 255 Up and Down In phase Movement Channel 7 Loom Tanem 0 255 Pattern Size Change Zoom in or out Size Channel 8 Colour Selection 0 255 Red Green Yellow When the value is set between 200 Channel 9 Motor Reset 0 255 255 the motors will reset Channel 10 Gradually Paint 0 255 Gradually Paint 7 KEY FEATURES RGY Colour Mixing DPSS Diodes Red 650nm Green 532nm Pre Programmed Beam Shows and Animations 64 Laser Patterns Controllable via DMX 3 Pin XLR 200 mW Total Laser Output Green 50mW Red 150mW DMX Sound Active Auto Master Slave Run Modes 10 DMX Channels 8 TECHNICAL SPECIFICATIONS MODEL SPITFIRE RGY LASER DIODE DPSS Green 532nm Red 650nm SCANNER 1 8 High Precision Stepper Motor SCANNING ANGLE 30 COOLING SYSTEM Fan MAX RUN TIME Approximately 4 Hours WARM UP TIME lt 15 Minutes WORKING TEMPERATURE 10
8. reas outside walking paths seating areas or in areas were the fixture might be reached by unauthorized personnel Before mounting the fixture to any surface make sure that the installation area can hold a minimum point load of 10 times the device s weight Fixture installation must always be secured with a secondary safety attachment such as an appropriate safety cable Never stand directly below the device when mounting removing or servicing the fixture Whether installing inverted on a truss or ceiling or set on a flat level surface see illustration below Be sure this fixture is kept at least 0 5m 1 5 ft away from any flammable materials decoration etc Always use and install the supplied safety cable as a safety measure to prevent accidental damage and or injury in the event the clamp fails Mounting Points Overhead mounting requires extensive experience including calculating working load limits A knowledge of the installation material being used and periodic safety inspection of all installation material and the fixture are all imperative and should only be performed by a qualified technician Improper installation can result in bodily injury and damage Be sure to complete all rigging and installation procedures before connecting the main power cord to the appropriate wall outlet Regardless of the rigging option you choose for your MICROH SPITFIRE RGY laser fixture always be sure to secure your fixture with a safety cable Th
9. the power cord During initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective It should decrease gradually Please do not project the beam onto combustible substances Fixtures cannot be installed on or near combustible substances Keep more than 50cm distance from wall for proper ventilation and air flow If your fixture is or has become damaged in any way it shall be exclusively replaced or repaired by the manufacturer to avoid any hazard CAUTION Never touch the device during operation The housing may heat up CAUTION Never look directly into the light source as sensitive persons may suffer an epileptic shock CAUTION The electric connection must only be carried out by a qualified electrician A Class 3B laser is hazardous to eyes if exposed directly Diffused reflections such as from paper or other matte surfaces are not as harmful 3 OPERATION INSTRUCTIONS Do not turn on the fixture if it has been through severe temperature differences Damage may occur to the fixture Wait until unit is at room temperature to operate The unit should be protected from any tremor or agitation during transport Do not expose the fixture in any excessive heat moisture or any environment with too much dust when installing Do not lay any power cables on the floor It may cause electronic shock or damage to persons or equipment Make sure to att
Download Pdf Manuals
Related Search