UCAT-1 - Geostick
Contents
1. ACH user manual 2 Thread the labels into the printer as required 3 The BRAKING Control Knob adjusts the amount of Frictionless Braking that will be applied to the label roll being unwound LABELMATE s Frictionless Braking is speed proportional This means that for large label rolls you will want the BRAKING Control Knob turned to a higher setting to provide braking for the slowly turning roll For small rolls you can use a lower braking force setting as the roll will be turning faster 4 Begin the printing or slitting operation and adjust the BRAKING Control to provide the least braking that will adequately tension the label roll LABEL UNWINDING FOR LABEL SLITTING The UCAT 1 Label Rewinder is ideal as part of a setup to slit labels If small labels are printed several up across and then slit to their desired width you realize much greater effective print speed and you also achieve much greater print head and ribbon efficiency LABELMATE offers three Label Slitters Models S 100 S 200 and S 100 SP that can be used with the UCAT 1 Slitting can take place either in line except with the S 100 SP directly after exiting the printer or off line where a roll of printed labels is unwound from a LABELMATE UCAT 1 Label Unwinder2. Core Holder option Skip to step 4 1 STANDARD AND 10 Identify the inner Label Flange Plate Slide the Flange Plate onto the hollow end of the Rewind Shaft For maximum width the Flange face should be flush with the end of the Shaft Tighten the screw in the Hub until it is snug Not too tight CHUCK Mount the inner Flange onto the Quick Chuck with two screws provided Slide the Shaft and Flange Assembly onto the UCAT 1 Motor Shaft allowing for clearance to the UCAT 1 Chassis and Motor Screws Tighten the Allen Screw onto the flat part of the Motor Shaft until it is tight ACH Slide the Hub of the ACH over the motor Shaft of the CAT 2 Position the Hub so there is a gap between the ACH Hub and the Rewinder Drive Unit case Tighten the Allen Screw onto the flat part of the Motor Shaft until it is tight Set the UCAT 1 in place near the label entrance path to the printer or LABELMATE Label Slitter depending on the job to be run CAUTION AVOID ACCIDENTS THE UCAT 1 WEIGHS OVER 10KG 22Lb SO CHOOSE ONLY A STURDY SURFACE ON WHICH TO SET THE UNIT A WARNING This Product is for indoor use only Not for use in wet locations LABEL UNWINDING FOR PRINTING The UCAT 1 is bi directional It can unwind labels in either direction 1 Slide the roll of labels to be unwound over the Quick Chuck or Vanes on the shaft until the core is against the inner Flange Plate On the Quick Chuck tighten the Lock Knob for an ACH see the
3. MAINTENANCE Your UCAT 1 requires no maintenance Product Limited Warranty All Labelmate Products are warranted to the original end user customer to be free from defects in materials and workmanship If it is determined by Labelmate that a product has failed under the terms of this warranty the product will be repaired or replaced at no charge to the customer Labelmate reserves all rights to determination of coverage and liability under this warranty The warranty period for all new Labelmate products is outlined below Warranty Period Products Covered Label Rewinders ayeas Label Unwinders Label Counters mechanical parts only Label Slitters mechanical parts only Label Dispensers Printer Mechanisms Power Supply Modules Counter modules Encoders Any products not specified above The warranty period for all products starts on the date purchased by the original end user customer Warranty coverage is not transferable with ownership and will terminate immediately upon rental resale or any other change in ownership This warranty does not cover repair to any product which is damaged has been modified is missing parts or has been opened or repaired by any unauthorised person Use of any unauthorised accessory or attachment will void coverage Purchase documentation should be retained for coverage verification In the event your product requires service please contact the distributor you bought the product from The cus
4. tomer assumes responsibility for all cost and risk incurred in transport for service Labelmate makes no other warranty of any kind expressed or implied or to suitability or fitness for a particular purpose No other person agent or reseller is authorised to give any warranties on behalf of Labelmate Any obligation to warranty other than that specifically addressed above is hereby disclaimed LABELMATE LLC 69 AVENUE ALPHONSE XIII 1180 BRUSSELS BELGIUM TEL 322 375 69 60 FAX 322 375 38 96 brussels labelmate com www labelmate com LABELMATE User_UCAT 1 02 07 UCAT Label Unwinder with Adjustable Braking e Variable Speed Controlled Braking e Choice of Core Holders e Non Powered Remove all parts from the shipping container and verify contents Package Contents e User Manual this document e UCAT 1 Unit e LABELMATE Quick Chuck Quick Locking Core Chuck or Standard Shaft with three 3 metal Vanes installed or Model 10 INCHES Shaft with six 6 metal Vanes installed or Model ACH Adjustable Core Holder e 300mm 12 Plastic Flange Plate Retain the Shipping Container and Packaging for Storage and Transport e KEEP MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE e SPECIFICATIONS Max Label Roll Weight Max Label Roll Size 7Kg 15 4Lb for Standard 15Kg 83Lb for QC 6Kg 13 2Lb for ACH 300mm 12 diameter 280mm 11 for ACH SET UP if you have the ACH Adjustable
Download Pdf Manuals
Related Search