SHS-3320 Full Guide
Contents
1. Note Only for SHS 3320 Door Preparation Lock Installation e 2 1 8 54mm hole saw Main Hole e 2 Phillips screwdriver e 1 25mm hole saw Dead bolt hole e Pincers Cut the tailpiece e 1 8 2 5mm drill bit Dead bolt screw hole e Chisel and hammer e Drill poortock SHS 3320 3321 Door Preparation Step 1 Check the Door Status 1 This lock supports door thickness of 1 3 8 to 2 5 32 35 to 55mm 2 Using the provided lock template ensure that there are no obstructions that would prevent installing the lock properly 3 Take note of which orientation the deadbolt will need to be installed left hand or right hand Left handed Door Right handed Door When viewed from the When viewed from the Outside Outside the hinge is on the the hinge is on the right left d gt Min 50mm Please be aware of that there has be more than 50mm gap between the door frame and the external power contact to place the 9V battery for temporary access Step 2 Mark on the Door Check the location and direction of the deadbolt attach the drilling template page 27 on the side of the door and mark on it with a pen 1 Align the horizontal line across the door 2 Align the vertical line over the door 3 Mark the centers of the holes with the drilling template 4 Mark the centerline of the deadbolt by aligning it with the vertical line2. CAUTION In case of right handed door insert the tailpiece horizontally In case of left handed door insert the tailpiece vertically pocrtek SHS 3320 3321 3 Installing the Mounting Plate A Left handed Right handed Detach the Interior Mounting Plate from the interior unit According to the right or left handed door adjust the link and attach the mounting plate Fasten the interior mounting plate with three TH M5x40 H2 90 of the way Align the Exterior Unit with the Interior Mounting Plate and then tighten the screws Cover the rubber pad on the Interior Mounting plate CAUTION Do not over tighten and check the movement of dead bolt by the mechani cal key 4 Installing the Magnetic Sensor Install the door side magnetic sensor It should be installed in right way of the door CAUTION The gap of the magnet sensors between the door side and the door frame should be within 3 4 20mm If the gap is to wide pull out the door side magnetic sensor to adjust the gap enough to detect Connect the cable from the exterior unit to the interior unit 2 After connecting the cable push the cable into the hole of the door poorbok SHS 3320 3321 6 Fix Screw for the Interior Unit 1 Before installing the interior unit check the direction of the thumb turn whil
3. A poortock SHS 3320 3321 Step 3 Drilling 1 Drill a 2 1 8 54 mm diameter hole through the door as indicated on the template using a hole saw 2 Drill a 1 25 mm mortise hole using a hole saw 3 Drill strike plate holes using a drill bit 1 8 2 5 mm es 54mm 2 5mm Step 4 Strike Plate Installation 1 Using the template locate the center horizontal line for the deadbolt hole which lines up with the center of the 2 1 8 hole and draw a horizontal line on the door frame to mark where you will make the deadbolt mortise hole 2 Measure half the thickness of the door Now measure that distance from where the door stops at the frame when the door is closed toward the door jamb and mark a straight vertical line the length of the door strike plate Draw a horizontal line from the mark you made in Step 1 toward the vertical line Where both lines cross make a 1 25 mm diameter hole 1 2 13 mm in depth FH T4 x 19 3 Align the holes of the strike plate with the vertical line Trace the outline of the strike plate and mortise with a 1 16 1 6 mm indentation Attach the strike plate with the 2 screws provided pocrtek SHS 3320 3321 Preparing the parts 1 Adjusting the length of the dead bolt O Turn the body of the dead bolt to adjust the length of the dead bolt It can be 60mm 2 3 8 or 70mm 2 3 4 2 Changing the faceplate of the
4. poortock SHS 3320 3321 Setting the Out of Home Security Function A When the door is closed Press the button within 6 of the touchscreen will 3 seconds light up Ding dong dang _ Setting Double locking J Releasing Double locking r ne Press the OPEN ER Press the OPEN CLOSE button for 5 CLOSE button or turn seconds while the door the Thumbturn lever is locked s amp Ding dong dang Ding dong ding dong B Additional Functions EB ED lt ee E A poortock OHS 3320 3321 Miscellaneous Reset to Factory Default A Resetting the lock will delete all registered information Note After Reset let the sensor detect the magnet to set the hand type again All registered Master and user data will be deleted and the lock will be reset to default settings Refer to the Program section on Page 15 for default values Press the Registration button for 10 sec Enter the current Master PIN Code and press onds the 4 button Successful Ding dong Ding ding Successful Ding dong dang Ding ding Failed Ding dong ding dong 9V Battery Emergency Power Note Please be aware of that there has be more than 50mm gap between the door frame and the external power contact to place the 9V battery for temporary access j Continuing to use the lock without replacing the batteries when requir
5. Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is con nected Consult the dealer or an experienced radio TV technician for help CAUTION Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user s authority to operate the equipment poortock SHS 3320 3321 LIMITED PRODUCT WARRANTY Installation of the product is considered acceptance of warranty conditions SAMSUNG SDS CO LTD SAMSUNG SDS warrants its products to be free from manufactur ing defects in materials and workmanship for 12 months from the date of purchase SAMSUNG SDS will within said period at its option repair or replace any product failing to operate correctly without charge to the original purchaser or user This warranty shall not apply to any equipment or any part thereof which has been repaired by others improperly installed improperly used abused altered damaged subjected to acts of God or on which any serial numbers have been altered defaced or removed SAMSUNG SDS does not warrant the performance or sale conditions of the seller installer There are no warranties express or implied which extend beyond the description on the face hereof There is no express or implied warranty of merchantability of a warranty of fitness for a particular purpose Additionally this warranty is in lieu
6. SSD samsunc sos SMART porok Samsung Smart Door Lock User Guide SHS 3320 3321 Please review all included documentation and use the product as intended Safety precautions must be followed to avoid personal injury or property damage vet SHS 3320 3321 Introduction amp Helpful Tips Installation Components amp Tools Door Preparation Preparing the parts Installing Lock Setting of Right Handed Left Handed Programming Basic Lock Operation Overview Programming Features amp Definitions Programming User PIN Codes amp User Cards Security Functions Miscellaneous Miscellaneous Information Troubleshooting User Registration Table Product Specifications Warranty Drilling Template Tailpiece Setting Introduction Congratulations on the purchase of your Samsung Smart Door Lock Your lock has a touch sensitive number display pad and optionally a 13 56MHz Card reader Up to 70 users can be registered to gain access with unique Codes or Access Cards supports ISO14443A type The touchscreen makes it convenient to enter the code and the Randomizer function helps prevent lockpicking using fingerprint traces on the touchscreen Other convenient functions such as Automatic Locking Sound Setting Out of Home Security etc provide advanced security and peace of mind You can unlock the door using video intercom s monitor after connecting a Samsung video intercom Refer to page 9 for conne
7. 1234 OPEN CLOSE Button A one touch button to open the locked door It is also used to lock the door from inside in the Manual locking mode Out of Home Security Function This function prevents intrusions from outside when no one is home Pressing the OPEN CLOSE button while the Out of Home function is enabled sounds an alarm You can enable this function by touch of a certain button poortock SHS 3320 3321 Random Security Function This mode prevents the disclosure of the PIN Code by enter ing the PIN Code after authenticating 2 arbitrarily selected numbers When the buttons for 2 arbitrarily selected numbers are illuminated pressing the 2 illuminated buttons illuminates the whole touchscreen You can enable or disable the Random Security function This function is enabled by default Registration Button This button is used to change Master PIN Code User PIN Codes User Cards or the lock settings It is found below the battery cover of the Interior Unit The length of time the Registration button is pressed varies depending on the function Resetting Deletes all registered information and restores the factory default After resetting change the Master PIN Code for security Restart Button This button resets the lock when the lock stops functioning Registered infor mation is not deleted Sound Setting The volume during the input of numbers and opening or locking of the door can be set from Level 0 Level 3 Th
8. User PIN Code must be 4 12 digits Enter another Number or press the Registration button to quit User E 0 EDO H 0 16 A Registering a User Card Smart Door Lock Open the battery cover of the Interior Unit and press the Registra tion button briefly Ding dong 1 4 7 When the touchscreen is il luminated enter the current Master PIN Code default is 1234 and press the 5 button Successful Ding dong Failed nf Ding dong ding dong Enter a User Number 1 70 to register the User Card code and press the x button Choose a User Number that has not already been used Successful 1 Ding dong Failed Ding dong ding dong with the Card to regis ter Ding dong dang Enter another User Number or press the Registration button to quit of 00 gt 0 8 Deleting User PIN Code User Card Open the battery cover of the Interior Unit and press and hold the Registra tion button for 5 seconds Ding dong Ding ding a 4 7 Enter the Master PIN Code and press the x button Successful 11 Ding dong Failed nf Ding dong ding dong o ow No e E SHS 3320 3321 Enter the User Number 1 to 70 of the User PIN Code or Card to be deleted and press the x button Successful 1 Ding dong dang Failed Ding dong ding dong
9. and re register e Ensure that the User PIN Code is 4 12 digits long can t register the User Card e The User Number has already been used Delete the de sired User Number and re register e Ensure that the card is touched to the card reader within 10 seconds of entering the User Number entered the PIN Code and pressed the x button but the door won t open e Check that the registered PIN Code was entered cor rectly e If the touchscreen illumination turns off while entering the PIN Code the button input was not registered Touch the Touchscreen to illuminate the touchscreen and enter the PIN Code again from the beginning The touchscreen illumination is turned off automatically if there is no input within 5 seconds can t unlock the door with my Card e The Card is either unregistered or unrecognized e The Card must touch the Card reader correctly can t unlock the door with my PIN Code or Card Check if the Double locking function has been enabled When this function is enabled the lock will not open with a PIN Code or Card Touch the Touchscreen when the Double locking function is enabled causes the lock to emit a Too t too t sound poortock SHS 3320 3321 My PIN Code or Card is authenti cated but the door won t open The lock may be malfunctioning Please contact service center The door won t lock automatically when close it e
10. dead bolt Change the faceplate of the dead bolt following the size of a strike hole 71 O Rectangle Strike hole Round Strike hole Q l 1 No need to change Remove the strike faceplate with a screw driver Turn the inner faceplate to take out it Insert the round faceplate 3 Adjusting the length of the tailpiece Tailpiece drawing How to cut 1 Press the V cut line with pincers to make more cut line Hold the end of the tailpiece with pincers Bend it up and down until it is separated For more information refer to page 31 35140 45 50 55 poortock OHS 3320 3321 Outside Inside 1 Installing the Dead Bolt E 1 Before installation 1 Check the faceplate type of your door 2 Make sure the deabolt directon as shown before inserting it into a door side 2 Insert the deadbolt from the side of the door 3 Fix the deadbolt using two FH T4X19 screws If there is round strike hole change the faceplate and insert the deadbolt following right side drawing Left handed Right handed 1 Ensure the Exterior Unit is aligned with the center hole of the deadbolt and the tailpiece is already cut 2 Attach the exterior unit 3 Insert the tailpiece to the exterior unit through the dead bolt The dead bolt must be in a retracted position
11. of all other obligations or liabilities on the part of SAMSUNG SDS Any action for breach of warranty including but not limited to any implied warranty of merchant ability must be brought within the six months following the end of the warranty period In no case shall SAMSUNG SDS be liable to anyone for any consequential or incidental damages for breach or this or any other warranty express or implied even if the loss or damage is caused by the seller s own negligence or fault SAMSUNG SDS shall have no obligation under this warranty or otherwise if the product has been repaired by others improperly installed improperly used abused altered damaged sub jected to accident nuisance flood fire or acts of God or on which any serial numbers have been altered defaced or removed SAMSUNG SDS and its distributor will not be responsible for any dismantling reassembly or reinstallation charges This warranty contains the entire warranty It is the sole warranty and any prior agreements or representations whether oral or written are either merged herein or are expressly cancelled SAMSUNG SDS neither assumes nor authorizes any other person purporting to act on its behalf to modify to change or to assume for it any other warranty or liability concerning its products In no event shall SAMSUNG SDS be liable for an amount in excess of SAMSUNG SDS s original selling price of the product for any loss or damage whether direct indirect incidenta
12. up and down until it is separated 32 Smart Door Lock SHS 3320 3321 poortock SHS 3320 3321 MEMO 33 pocrtek SHS 3320 3321 MEMO 34 35 Smart Door Lock SHS 3320 3321 poortock SHS 3320 3321 Product information and customer service contact SAMSUNG SDS SAMSUNG SDS Co Ltd reserves the right to change availability of any item in this catalog its design construction and or its materials Copyright 2011 SAMSUNG SDS Co Ltd All right reserved Reproduction in whole or in part without the express written permission of SAMSUNG SDS is prohibited GC68 01765A ED 04
13. with a PIN Code Smart Door Lock SHS 3320 3321 Touch the Touchscreen x NR The touchscreen will illu minate If the Random Se curity function is enabled press the 2 illuminated x N BR Enter the PIN Code and press the x button Successful Ding dong dang dong The door opens within one second Failed Ding dong ding dong numbers ke Opening the Door with a Card Touch the Card reader with an Access Card Touch the Touch screen The door opens within one second Successful Ding dong dang dong Failed Ding dong ding dong Ei Ne Opening the Door in Double Authentication Mode gt The touchscreen will Enter the PIN Code and press the x button Successful Ding dong Failed mt Ding dong ding dong 2 5 8 0 NA XN BR A Ua Touch the Card reader with an Access Card Successful Ding dong dang dong Failed mt Ding dong ding dong Touch the The door opens Touch screen illuminate within one If the Random Security second function is enabled press the 2 illuminated numbers pocrtek SHS 3320 3321 Programming Features Outside SAMSUNG Touchscreen Open Close Button Card Reader Thumbturn Lever Emergency Cylinder SHS 3321 does not sup
14. 22 not included Source attery not included Operation Method Electronic Control Method PIN Code entry or Card reading Weight 1 8Kg including both inside and Exterior Unit 68 0 mm W x 180 0 mm H x 36 5 mm D 2 11 16 inch W x 7 3 32 inch H x 1 7 16 inch D Product Dimensions Exterior Unit 68 0 mm W x 180 0 mm H x 38 3 mm D 2 11 16 inch W x 7 3 32 inch H x 1 1 2 inch D Interior Unit The content of this manual is subject to change without prior notice to the user in order to enhance the performance of the product FCC NOTICE NOTE This equipment has been tested and found to comply with the limits for a Class B digital de vice pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna
15. Check if Auto Locking is set When Manual Locking is set touching the Touchscreen locks the door e f the door doesn t lock automatically when Auto Locking is set then the lock has been installed incorrectly e The Auto Locking function is not activated when the bat teries are completely discharged Check if the batteries are discharged hear the Too t too t warning sound when touch the Touch screen When the Double Locking function is enabled touching the Touchscreen issues this warning sound Check if Double locking is enabled disable the function and try again The lock issues a different melody Fur Elise when activate it The sound indicates that it is time to replace the batteries Replace with new batteries within a week There is no response when touch the Touch screen e Use a pin to press the hole on the right of the external power contact of the Exterior Unit e If doing the above does nothing contact the service cen ter pocrtek SHS 3320 3321 User Registration Table Management No PIN CODE CARD User Name Management No PIN CODE CARD User Name poortock SHS 3320 3321 Product Specifications Item Specifications Voltage 4 AA Alkaline 1 5V Batteries LR6 6V Emergency Power 9V Battery 6LF
16. ction diagram to a video intercom Helpful Tips Do not attempt to repair the product yourself Change your codes regularly to ensure the security of your codes Minimize the lock s exposure to moisture including wet hands and direct contact with liquids Do not exert excessive force or use sharp instrument on the touchscreen Insert the batteries according to correct polarity When the low battery warning sounds replace all batteries immediately Do not mix old batteries with new batteries Use soft dry cloth to clean the lock and avoid cleaning with water alcohol or other chemicals poorbok SHS 3320 3321 Installation Components and Drawing Exterior Unit B Interior Unit Interior Rubber Pad Interior Mounting SHS 3320 SHS 3321 With key hole Without key hole Adjustable Deadbolt Strike Parts Magnetic Sensor Dom Alternate Faceplate Strike Dust Box Door Side Doorframe Side For round strike Screw for Strike and H2 Screw for H3 Screw for Tailpiece Dead bolt mounting plate Interior unit DD Daun sels Dea mano en 7 Rania 7 Oasen Li Duw Extra Parts y Spec FH T4x19 Spec TH M4x40 Spec FH M4x8 Mechanical Keys Batteries User Manual T JUU U
17. e sound is muted at Level 0 and is at maximum volume at Level 3 The registration mode operates at Level 2 regardless of the sound setting User Card You can register up to 70 User Cards including the User PIN Codes You can open the door with a User Card User Management Number It is the same number as the registered user s address and can be set from 1 to 70 The User Number should be managed with caution as it is used to register or delete User PIN Codes Cards User PIN Code You can register up to 70 User PIN Codes 4 12 digits including the User Cards You can open the door with a User PIN Code Scope of Master User Settings 5 Factory Default Settings Master User Function Factory Default Master PIN Code 1234 Opening the Door Volume Level 2 Setting Up the Sound User PIN Code Card None Changing Master PIN Code Locking Mode Auto Registering User PIN Code Card Out of home Security Deletion of User PIN Code Card Function Disabled Setting the Locking Mode Double locking Disabled Setting Out of home Security Random Security Enabled Setting Double locking Double Authentication Mode Disabled Setting Random Security Factory Reset Setting the Volume Setting the Double Authenti cation Mode Smart Door Lock SHS 3320 3321 Programming User PIN Codes amp User Cards Note Pressing the Registration button is only availabl
18. e the dead bolt is in the OPEN POSITION 2 Open the battery cover 3 Align the Interior Unit on to the Interior Mounting ft handed Right handed Plate and attach it with 4 screws CAUTION Check the movement of the dead bolt by the thumb turn a J S Install 4 batteries A Melody will sound when all 4 batteries are installed correctly Close the door to detect the magnetic sensor You can hear the beep sound when the magnetic sensor detects After that press OPEN CLOSE button to check whether the dead bolt works properly Stick the magnetic sensor with attention on the distance CAUTION The gap between the door side and the door frame magnetic sensors should be close enough to be detected Dry Contact Connect the cable of video intercom to the Interior Unit SHS 3320 3321 receives 1 second of dry contact signal to open the door remotely It is normally compatible with SHT 3006 and other Samsung Video Intercom systems pocrtek SHS 3320 3321 Setting of Right Handed Left Handed All status should be checked while the dead bolt is in OPEN POSITION Left handed Right handed Magnet sensor Tailpiece Tailpiece Link Thumb turn Programming Opening the Door
19. e while the door is open Deadbolt must be unlocked Maximum number of user registration is 70 User PIN Codes User Cards Key Fobs Ed Changing the Master PIN Code Open the battery cover of the Interior Unit and press the Registration button briefly 1 3 4 6 7 8 9 0 O When the touchscreen is illuminat ed enter the current Master PIN Code default is 1234 and press Ding dong the x button Successful 14 Ding dong Failed Ding dong ding dong 7 x 4 12 digits 2 5 8 0 Enter the new Master PIN Code and press the button Successful Ding dong dang Failed 4 Ding dong ding dong Note Master PIN Code must be 3 6 9 A Old New 0 00 00 Registering a User PIN Code Open the bat tery cover of the Interior Unit and press the Reg istration button briefly Ding dong When the screen is illumi nated the current Master PIN Code default is 41234 and press the gt button Successful Ding dong Failed 10 Ding dong ding dong touch enter o o w Enter a User Number 1 70 to register the User PIN Code and press the button Choose a User Number that has not already been used Successful Ding dong Failed 4 Ding dong ding dong S Enter a new User PIN Code and press button Successful Ding dong dang Failed Ding dong ding dong Note
20. ed will lead to lock malfunction Touching a 9V DC battery to the external power contacts on the under side of the Exterior Unit will allow for temporary access continue touching the battery to the contacts until the lock is open Restart Function Note Restarting does not delete registered information If there is no response after touching the Touchscreen use a pin to press the Restart button on the left of the external power contact of the Exterior Unit poortock SHS 3320 3321 Troubleshooting When the lock doesn t function correctly please check the items below If you can t resolve the problem please contact the nearest service center Problem Resolution Reference There is no power e Check if the batteries are inserted in the correct polarity e Check that the batteries have a full charge e Check that the Exterior Unit cable has not come loose can t change the Master PIN Code e There was a delay while changing the PIN Code The touchscreen must be illuminated when changing the PIN Code Also after entering the first digit the next digit must be entered within 10 seconds e Replace the batteries if they are discharged e Refer to the Changing the Master PIN Code section in the user manual and try again Ensure that the Master PIN Code is 4 12 digits long can t register the User PIN Code e The User Number has already been used Delete the de sired User Number
21. l consequential or otherwise arising out of any failure of the product Seller s warranty as hereinabove set forth shall not be enlarged diminished or affected by and no obligation or liability shall arise or grow out of Seller s rendering of technical advice or service in connection with Buyer s order of the goods furnished hereunder SAMSUNG SDS recommends that the entire system be completely tested weekly Warning Despite frequent testing and due to but not limited to any or all of the following criminal tampering electrical or communications disruption it is possible for the system to fail to perform as expected SAMSUNG SDS does not represent that the product system may not be compromised or circumvented or that the product or system will prevent any personal injury or property loss by burglary robbery fire or otherwise nor that the product or system will in all cases provide adequate warning or protection A properly installed and maintained alarm may only reduce risk of burglary robbery fire or otherwise but it is not insurance or a guarantee that these events will not occur poortock SHS 3320 3321 Consequently seller shall have no liability for any personal injury property damage or other loss based on a claim the product failed to give warning Therefore the installer should in turn advise the consumer to take any and all precautions for his or her safety including but not limited to fleeing the premises and calling
22. o t Double locking sound pocrtek SHS 3320 3321 Double Authentication Mode This mode requires both User Card and PIN Code to open the door ensuring more security However Master PIN Code can open the door regardless of mode To enable this mode more than 1 User Card and PIN Code must be registered This mode is disabled by default Double locking Double locking prevents the lock from being unlocked from the outside You can enable it by using the OPEN CLOSE button Emergency Power Contact Continuing to use the lock without replacing batteries when required will lead to the batteries discharging and cause the lock to malfunction You can open the door by touching the external power contacts on the Exterior Unit with a 9V battery and then touching with the Card or entering the PIN Code Indicator Lamp Indicates the operational status when the Card is being read or the lock is in operation Intrusion Detection Function When the Interior Unit is forcibly detached while the door is locked it is detected by the magnetic sensor and an alarm is sounded The function is not activated when the magnet is not used The Intrusion Detection function is a basic function and cannot be enabled or disabled Locking Mode Auto Manual You can enable or disable the function for locking the door automatically when it is closed The factory default is Auto mode Auto The door is locked automatically 2 seconds after it is closed H
23. owever it does not function if the magnet is not used or the batteries are completely discharged Manual When the door does not lock automatically when it is closed touch the Touchscreen or the OPEN CLOSE button on the Interior Unit will lock the door Low Voltage Indicator Refers to the state when the operating voltage of the lock is lower than the standard voltage and activates the Low Voltage Alarm Fur Elise to indicate that the batteries need to be replaced Use the Emergency Power when the batteries are completely discharged Magnetic Sensor Detects the opening and closing of the door Malfunction Prevention Function Mischief Prevention Function When more than 5 failed authentication attempts with unregistered PIN Codes Cards occur a warning sounds for 10 seconds and the lock stops operating for 3 minutes While lock operation is stopped a beep is sounded every 10 seconds and the lock is activated again automatically after 3 minutes The Malfunction Prevention function is a basic function and cannot be enabled or disabled Thumbturn Lever When the batteries are completely discharged this device is used to me chanically lock or unlock the door from inside Master PIN Code You can enter only one Master PIN 4 12 digits Code You can register the User PIN Codes Cards after authenticating with the Master PIN 4 12 digits Code You can open the door with the Master PIN Code and the factory default is
24. police or fire depart ment in order to mitigate the possibilities of harm and or damage SAMSUNG SDS is not an insurer of either the property or safety of the user s family or employees and limits its liability for any loss or damage including incidental or consequential damages to SAMSUNG SDS s original selling price of the product regardless of the cause of such loss or damage Some states do not allow limitations on how long an implied warranty lasts or do not allow the exclusion or limitation of incidental or consequential damages or differentiate in their treatment of limitations of liability for ordinary or gross negligence so the above limitations or exclusions may not apply to you This Warranty gives you specific legal rights and you may also have other rights which vary from state to state In case of the product defect contact our authorized Customer Service Center In order to exer cise the warranty you must contact our authorized Customer Service Center and obtain a proper RMA the product must be returned to our authorized Customer Service Center at user s ship ping expense and the replacement product will be shipped back at our expense For product service the product in all cases must be accompanied by below warranty form Cus tomer must ask the reseller or installer to fill out the warranty form indicated below otherwise the product warranty may be considered void Visit our website at www sds samsung com and go to Sup
25. port Restart Button External Power Contact Inside Registration Button Magnetic Sensor Battery Cover Description Symbols Description Touch the Touchscreen Press the x button It is used to complete number entry Press the Registration button It is used to change the PIN Code or set other functions R Press the Registration button briefly 1 second R5 Press the Registration button for 5 seconds R10 Press the Registration button for 10 seconds Enter the Master PIN Code 4 12 digits Factory Default 1234 Press the Number buttons poortock SHS 3320 3321 Symbols Description Description Enter the User PIN Code 4 12 Repeat the process inside digits the rectangle Touch the Card reader with the Press the OPEN CLOSE User Card button Enter the User Management Number Can be set from 1 Sound Icon Display to 70 Sound Indicators Sound Description Fur Elise Low voltage warning sound accompanied with OPEN CLOSE button flashing red Ding Button input sound Ding dong ding dong Error sound Ding dong dang Success sound Ding dong Input standby sound Toot toot 10 seconds Malfunction prevention warning Ti ti ti ti 5 minutes Intrusion Detection Out of home Security warning Too t to
26. port menu to find the contact informa tion of our worldwide distributors Date of Purchase or Installation MM DD YY Name telephone and full address of purchaser Stamp or Signature of authorized reseller installer Product Code and Serial Number 26 Smart Door Lock SHS 3320 3321 mat SHS 3320 Fold along this line gt Folding Line and align it to the corner edge of the door 5 32 Deep E O2 1 8 Bore 1 DIA Latch Hole 27 28 Smart Door Lock SHS 3320 3321 mat SHS 3320 70mm Backset r p 7 1 Fold along this line gt and align it to the corner edge of the door y 2 1 8 Bore 1 DIA Latch Hole 29 30 Smart Door Lock SHS 3320 3321 poortock SHS 3320 3321 Tailpiece Settino Tailpiece drawing 1 Check the thickness of your door with our tailpiece drawing or a ruler 2 According to your door thickness cut and adjust the tailpiece as following way ex1 Thickness 40mm 35 40 45 50 55 cutting point ex2 Thickness 53mm 35 40 45 50 55 Fold along this line gt Folding Line and align it to the corner edge of the 35mm door How to cut 1 Press the V cut line with pincers to make more cut line 2 Hold the the end of the tailpiece with pincers 3 Bend it
Download Pdf Manuals
Related Search