Contents
1. Limited Warranty SCOPE OF WARRANTY Next Technologies Inc NextDesk warrants to the original purchaser its new desks except for components not warranted under Exclusions manufactured by NextDesk to be free from defects in material and workmanship under normal use and service NextDesk s obligation under this warranty is limited to the repair or replacement at NextDesk s option of the parts or the products the defects of which are reported to NextDesk within the applicable warranty period and which upon examination by NextDesk prove to be defective APPLICABLE WARRANTY PERIOD The applicable warranty period measured from the date of delivery to the original user shall be three 3 years for all warranted desks EXCLUSIONS This warranty does not cover and NextDesk shall not be liable for the following 1 repairs and replacements because of misuse abuse negligence alteration accident freight damage or tampering 2 products which are not installed used and properly cleaned as required in the NextDesk Installation and or Installation Operation Manual for this applicable product 8 products considered to be of a consumable nature 4 Shipping to or from repair center 5 accessories or parts not manufactured by NextDesk 6 charges by anyone for adjustments repairs replacement parts installation or other work performed upon or in connection with such products which is not expressly au2. CONNECT CABLES Motor cables are pre mounted to desktop and pre wired to the control box Plug each motor cable into the cable leading to the control box IMPORTANT DO NOT plug desk into power outlet at this time 2 IMPORTANT Carefully turn desk upright on level floor Desk is NOT complete DO NOT put weight or load on desk Use proper lifting techniques when lifting Failure to do so could result in serious back injury INITIALIZE DESK A Connect power cord to standard wall outlet For desks with Power Management the power cord is factory attached For desks without Power Management plug power cord into the control box prior to connecting to wall outlet B Press and hold the button until the lifting columns have completely retracted and continue to hold for 5 seconds after all movement stops C Once the columns are completely retracted they will automatically run approximately 5 mm out again and then slowly run in again Do not release the button until 5 seconds after all movement has completely stopped Note Itis sometimes necessary to press the button twice to start initialization There may be a short delay before movement begins Note If the button is released before the sequence is complete then initialization is interrupted and the process must be started again from the beginning 2 CABLE MANAGEMENT Maintain the sleek lines of NextD
3. to the shipping company and fill out a concealed SS tea J damage report fu It is recommended to leave desktop in SS the original box for steps 1 6 to preserve the destop finish Remove all other parts from the box QUICK TIP INSTALLING SCREWS DO NOT over tighten screws during installation 2 EN v oe SYSTEM COMPONENTS LIST h h h 9 X Desktop control box cable controller mounting plate any accessories attached Lifting Column Bottom Support Footing 10 AC Chord o PARTS LIST P gt 4 M6 25mm Machine Screw Long 6 Lift Mounting Screws 10mm Short D 1 Allen Wrench Hex Key 5 32 A 1 Allen Wrench Hex Key 1 8 D 5 Adhesive Zip Ties 2 LA v o N COMPONENTS DIAGRAM Microprocessor Control Box Desktop reference detail below D Upper Support gt Lifting Column l Digital Controller Base Support Microprocessor Control Box Top View wed Anti Collision Dongle Controller Cable Lifting Column Connector Power Cable Le PA o dh CONNECT LIFTING COLUMN TO DESKTOP oe Hardware Required 6x 10mm Allen Screws IMPORTANT Cable must face back of desk 2 O QO oO D un O O l LL U LLJ Z Z O U TO COLUMN IMPORTANT Countersink holes should face up A D
4. AN next desk Solo Plus Assembly Instructions Preface We are delighted that you have chosen NextDesk Congratulations you have selected the most advanced and sophisticated power adjustable workstation available today Our bodies weren t meant to sit or stand for hours at a time Now you have the choice to sit or stand with the press of a button This user manual gives basic instructions for NextDesk Solo Plus model We are sure that your NextDesk will provide you with many years of enjoyment Should you ever experience a problem with any our products please contact us Thank you for choosing Nextdesk We hope you enjoy your NextDesk for many years NextDesk Team Preface AN Table of Contents Safety INStrUCHONS eerren ena aea aaRS Page 1 Unpacking Preparation Tools Needed Page 3 System Components List amp Parts List Page 4 Components DIAG ai Seine dass dossiers Page 5 Step 1 Connecting Lifting Columns to Desktop Page 6 Step 2 Connecting Floor Supports to Columns Page 7 Step 3 Connecting Cables sise intenses Page 8 Step Alain Pr ce ARR RE poensassiets Page 9 Step 5 Cable Management sisih cise tiederssaeeecss ceweriawaan Page 10 Operating C DONS a me rm Page 11 Anti Collision PSAUUlG icssccetradecectadde dasa dev dd uae du eau Page 12 Maintenance amp DESCG LION aietveieneduedesn sued ea duvedantaseeastenvonndve
5. RNING The NextDesk systems do not withstand oil Description of the NextDesk Each NextDesk actuator lifting column is equipped with a motor and synchronicity is ensured by means of software that also takes account of an oblique load on the desk Soft start and stop are also part of this software which ensures a soft start and stop when adjusting the desk Maximum Duty Cycle Irrespective of the load the duty cycle of 10 6 min hour or maximum 2 min at continuous use must NOT be exceeded as this will result in overheating of the motor and control box Exceeding the duty cycle will result in a dramatic reduction of the life of the system 15 Gy Troubleshooting and Repairs Error Codes Below are the possible error codes which may be displayed on the controller marso mes ur Lifting columns are in an Initialize or Reinitialize unknown position Refer to Page 10 Overload in upwards direction had occured Reduce the weight on NextDesk direction has occurred downward movement Release all buttons amp press a valid Mogi Kee aickbiessod button or button combination Overload in downwards Remove objects that prevent Repairs In order to avoid the risk of malfunction all NextDesk repairs must be carried out by authorized NextDesk repair centers as special tools and gaskets must be used WARNING If any of the NextDesk products are opened there will be a risk of subsequent malfunction gt 16
6. e has been removed Method of operation The control box monitors the electric consumption on each lifting column If the electric consumption on one channel is increased more than a predefined slope a collision is assumed All channels are stopped immediately and all desk legs will start to run in the opposite direction approximately 50 mm The anti collision sensitivity is different in upward and downward direction Upwards the force is approximately 20 kg Downwards the load will be approximately 40 kg the load on the desk lifting column the desk what is on top of the desk Situations where the anti collision does not work These situations are If the collision happens during the initialization phase e If the collision happens within the first 1000 milliseconds or after the control button has been released e If the collision happens between the floor and the table and the load on the desk plus the weight of the legs are lower than 40 kg e If the collision happens over too long of a time e g if the collision is with a soft object 14 gt Maintenance Clean dust and dirt on the outside of the NextDesk and other components at regular intervals and inspect them for damage and breaks Inspect the connections cables and plugs and check for correct functioning as well as the security of the connection points The cleaners and disinfectants must not be highly alkaline or acidic pH value 6 8 WA
7. esk Spend a few minutes to tidy up all visible cords and cables and then cover with NextFlex e Straighten and untangle cables Connect loose cables into a bundle e Group the main cables running to your desk into a bundle main power cable network cable printer cable e Group the cables between your PC and desktop into a bundle monitor speakers e Cover bundles with NextFlex expandable cable cover e Attach the self adhesive zip ties underneath NextDesk and secure cables and bundles e Consider the optional NextDesk Vanity Cover Cable Raceway for even easier cable management available in matching aluminum m Zi OPERATING CONTROLLER Display Adjust Up Adjust Down Memory 1 2 8 Store Memory Up and Down Press either the up or down button for parallel drive and the system will drive until the button is released again or the system reaches end position Programmable Memory The four small buttons are used for memory drive storing memory Store Memory Presets a Raise or lower the desk to the height you wish to store as a preset b Press and release the button c Within these two seconds press a memory button Q or fee or The panel will acknowledge by showing 1 2 or 3 in the display depending on chosen position Using Memory Presets Press one of the memory buttons and the system will start driving to the preprogrammed memory position Keep the button pre
8. on level floors If you determine that your floor is unlevel you may wish to order floor supports with leveling screw pads a J gt 4 N v SAFETY INSTRUCTIONS cont Children must remain under close supervision to ensure that they do not play with the product It is important for everyone who is installing or using the NextDesk to have the necessary information and access to this User Manual A If there is visible damage on the product it must not be installed The NextDesk is not intended for use by young children or for those persons who require supervision Children should be supervised to ensure that they do not tamper or play with the NextDesk Before Installation Reinstallation or Troubleshooting A Stop the NextDesk A Switch the power supply and pull out the main power supply plug AN Relieve the NextDesk of any loads which may be released when unexpected Before Start up ZA Make sure the NextDesk has been installed as specified in this manual AS System Connection the individual parts must be connected before the control box is connected to the main power supply If the control box makes unusual noises or has an odor switch off the main power supply immediately Zn Make sure the cables are not damaged 2 EN v UNPACKING Carefully remove the packaging from the NextDesk and then inspect all components for any shipping damage Report any damage
9. s Page 13 Troubleshooting amp Repair ssmscuserssseseastssnadersdawiesiaedderianaceuiees Page 14 Warner ibn oanr aan Page 15 Table of Contents a A SAFETY INSTRUCTIONS WARNING FAILURE TO COMPLY WITH OR OBSERVE ALL ASSEMBLY SAFETY AND OPERATING INSTRUCTIONS AND WARNING REGARDING THE USE OF THIS PRODUCT MAY RESULT IN SERIOUS BODILY INJURY The safety of NextDesk clients and users is our primary concern To ensure safe operation Read and understand this manual before attempting to install or operate the NextDesk Verify that everyone who uses the NextDesk is informed of the contents of this manual This is the responsibility of the purchaser Leave this manual near the NextDesk and if possible permanently affixed to the desk Safe use of the system is possible only when the operating instructions are read completely and the instructions contained are strictly observed Failure to comply with instructions marked with the NOTE symbol may result in serious damage to the system or one of its components Persons who do not have the necessary experience or knowledge of the NextDesk must not use the product Persons with reduced physical or mental abilities must not use the NextDesk unless they are under supervision or they have been thoroughly instructed in the use of the apparatus by a person who is responsible for the safety of these persons QUICK TIP IS YOUR FLOOR UNLEVEL NextDesk is intended for use
10. ssed until the position is reached Display Function Shows the actual height OPERATING CONTROLLER cont Other Functions Adjusting Initial Height It may be necessary to adjust the displayed height due to different thicknesses of desktops The control will display 24 5 inches as the default desk height Procedure a Press and Q keys at the same time and keep them pressed for 5 seconds This allows the initial height to be adjusted Until the initial height is adjusted the display will show three minuses Hereafter the display will revert to showing the height b The height can then be adjusted by either Q or until desired height has been reached The system will return to normal operation and give a short blink after 5 seconds of inactivity on the keys 13 ANTI COLLISION FEATURE NextDesk offers an anti collision feature that can limit material damages to a desk if a collision with a solid object should occur Enabling the anti collision To enable the anti collision function a dongle must be mounted on one of the two control ports of the control panel on the underside of NextDesk The function is only active when the dongle is mounted Anti Collision If you remove the dongle the anti collision function is disabled Dongle Inspect NextDesk prior to use to determine if the anti collision dongle is properly inserted Do not use NextDesk if the anti collision dongl
11. thorized in writing in advance by NextDesk 17 Gh EXCLUSIVE REMEDY NextDesk s only obligation under this warranty is the repair or replacement of defective parts NextDesk shall not be liable for any direct special indirect incidental exemplary or consequential damages or delay including but not limited to damages for loss of profits or loss of use NO AUTHORIZATION No person or firm is authorized to create for NextDesk any other obligation or liability in connection with the products THIS WARRANTY IS NEXTDESK S ONLY WARRANTY AND IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED NEXTDESK MAKES NO IMPLIED WARRANTIES OF ANY KIND INCLUDING ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS 18 gh
Download Pdf Manuals
Related Search
PDF pdf pdf editor pdffiller pdf to word pdf to jpg pdf merger pdf combiner pdf converter pdf editor free pdf reader pdfescape pdf to excel pdf24 pdf compressor pdf to png pdf to word converter pdf viewer pdf24 creator pdf-xchange editor pdf to jpeg pdf files pdf to excel converter pdf converter free pdf history pdf24 tools