Dome Camera User Manual
Contents
1. crossed out wheeled bin mark symbolizes that within the European Union the product must be collected separately at the product end of life This applies to your product and any peripherals marked with this symbol Do not dispose of these products as unsorted municipal waste CE Mark This apparatus is manufactured to comply with the radio interference m The company does not warrant that this manual will be uninterrupted or error free We reserve the right to revise or remove any content in this manual at any time dg102_102a V1 0 FEATURES 1 1 2 7 CMOS Sensor 2 1080P video output 3 Low light sensitivity of 0 1 Lux F1 8 PACKAGE CONTENT gt IRcamera 1 gt User manual 1 DIMENSIONS S wT Dimensional Tolerance 5mm SPECIFICATIONS Pick up Element 1 2 7 CMOS image sensor Number of Pixels 1930 H x 1088 V Video Frame Rate 1080P 30fps 1080P 25fps Min Illumination 0 1 Lux F1 8 S N Ratio More than 48dB AGC OFF Shutter Speed 1 30 1 25 sec 1 720000 1 600000 sec Lens f3 6mm F1 8 Lens Angle 96 Horizontal 50 Vertical 116 Diagonal IRIS Mode AES White Balance AUTO USER PUSH 8000K 6000K 4200K 3200K AGC Auto Sharpness YES Flickerless 50HZ 60HZ OFF BLC YES Operating Temperature OC 40C Video Output 1 0 Vp p composite 750 Power Source 10 DC12V 0 5A Current Consumption 10 100mA Dimensions mm 100 x 60 H2. this unit 2 Video Output Connector VIDEO OUT Connect the camera video output to the video input of a DVR with 750 coaxial cable NOTE To ensure the camera has sufficient protection against moisture an extra waterproof measure such as by using an insulating tape must be used to cover the power and video connectors after connection CAMERA PARAMETERS This camera series has its own configuration menu and either of the two methods below is available to access the menu based on the camera model you have Method 1 On the DVR live view click the channel which connects this camera to display in the full screen mode and select to show the control panel and select to enter the camera menu u Method 2 On the DVR live view right click to show the DVR main menu and select ADVANCED CONFIG gt DCCS Then select the channel which connects this camera and click SETUP to enter the menu of camera parameters ADVANCED CONFIG CAMERA a fe os we DETECTION MENU SETUP ALERT NETWORK DISPLAY RECORD DEVICES DEVICE XXXXX NOTIFY CONNECTION OK EXIT NOTE The parameters available depend on the model you have
3. 684z lw CC TV Total Solution Dome Camera User Manual The product image shown above may differ from the actual product Please use this camera with a DVR which supports HD video recording Please read the instructions thoroughly before using the product CAUTION RISK OF ELECTRIC SHOCK CAUTION To reduce the risk of electric shock do not expose this apparatus to rain or moisture Only operate this apparatus from the type of power source indicated on the label The company shall not be liable for any damages arising out of any improper use even if we have been advised of the possibility of such damages The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons This exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance gt gt ROHS Announcement RoHS All lead free products offered by the company comply with the requirements of the European law on the Restriction of Hazardous Substances RoHS directive which means our manufacture processes and products are strictly lead free and without the hazardous substances cited in the directive conform The
4. The specifications are subject to change without notice INSTALLATION The product image may be different from the actual product 1 Turn Dome Cover as shown in Figure 1 counterclockwise to the end and take it off 2 Mark the positions of one power and video line hole and four screw holes on the ceiling as shown in Figure 2 amp Figure 3 Drill a hole on the proper position of the ceiling for the power and video line to pass through And then screw base to the ceiling Note Screws for installation are not supplied within the sales package Please prepare by yourself and use proper screws Suggestions a For safety please let the power and video line concealed behind the ceiling b If the installation spot doesn t allow the installation personnel to screw power and video line hole on the ceiling they could cut the concave edge of base to let the power and video line pass through Be sure to cover the line to prevent violent attack 3 Adjust the view angle of the lens as shown in Figure 3 Then put dome cover back to the base and turn clockwise m Figure 1 Figure 2 Figure 3 Figure 4 CONNECTION 1 DC12V Input Terminal Connect the power terminal of the camera to a DC 12V regulated power supply NOTE Please use the correct power adaptor DC12V regulated to operate this unit The power tolerance of this unit is DC12V 10 Over maximum DC 12V power input will damage
Download Pdf Manuals
Related Search