“Regular” BLUE STREAK Jack Handle
Contents
1. Regular BLUE STREAK ROLLER Rig ht End Blue Streak Roller used at right end if End Caps are attached Connecting Brace Regular BLUE STREAK Jack Handle Left End BLUE STREAK Jack Handle If End Caps are attached Pull Chain Gondola Train User s Manual Before amp During the Move Gondola Train User s Manual DAYS BEFORE MOVE BEGINS Prepare a Detailed Fixture and Floor Plan numbering gondolas on new layout design Analyze the positioning of the present gondolas and write a plan that will be the most efficient sequence of movements of the gondolas to their final position This will be extremely helpful in reducing double or triple moving of the gondolas 3 Place a temporary mark and number on gondolas that correspond to the numbers on your new floor plan This will provide everyone involved the easiest way to locate the final position of any gondola Remove solid panel or open kickplates Sweep amp Clean under gondolas and all open floor space Remove secure high or easily tip able items De merchandise shelves as necessary to be in accordance with load chart below This chart established a maximum load per side per gondola section as a function of deck depth Load applies to the sum total weight of all merchandise on all shelves on one side within a 4 section of gondola If de merchandising is required begin removing merchandise from the top shelves first This will lowe2. ach S HOOK onto main upright post as low on fixture as possible Pull the Pull Chain PC with a smooth even force to initiate movement Continue using PC guiding the fixture is better to grab fixture and guide with hands when pushing place hands on bottom halt of fixture Pushing from the too half will cause additional stress on fixture while moving fixtures Do not leave the Gondola Rollers under the gondolas for any extended length of time Rollers should be removed immediately after gondola has been moved Lower gondolas into position and replace base fronts if they were removed THE GONDOLAS ARE MOVED MOVE A DEPARTMENT AFTER SHELVING IS MOVED Set up an empty 8 or 12 gondola on Gondola Rollers Move the empty gondola to an area that needs to be relocated Place the merchandise onto the empty movable gondola in the exact position as it was on the original gondola counter balance the empty side of movable gondola with weight that is equivalent to the weight of merchandise being relocated 5 gal 4 paint cases of oil detergent etc Roll this gondola to the new location If there is product in the location place these items in the exact order on the backside of the movable gondola remove the counter balance weight items Rotate the gondola and place the merchandise onto its new location Replace counter balance weight and move to the area that the merchandise on the reverse side will be placed Continue
3. dola when you are unable to install the roller from the right side of the foot bracket Use with the standard Blue Jack Handle With the rollers Out to the front of fixture Connect ALL rollers by installing the Connecting Brace BSBC Insert the round pins on Connecting Brace into the square brace pockets on the roller Installing of Connecting Braces will keep rollers in place and help maintain rigidity in the base brackets and entire fixture during the move Failure to do this could cause failure of the Gondola components merchandise damage or injury to persons a Make sure retaining angles on the end of the Connecting Brace are positioned to lock roller onto fixture leg Once an individual section of gondola has been lifted Rollers installed amp Connecting Brace is properly installed we suggest turning the wheels in the direction of your initial movement of shelves This will help in making the initial push easier On new tile place a piece of carpet or cardboard under the handle floor pivot point and keep wheels clean to prevent marking of the new tile LIFT HEAVY SIDE UP FIRST SET HEAVY SIDE DOWN LAST one person per handle HOW TO NO READY TO MOVE Length and weight of gondola will determine the quantity of people needed to move the Unle Roll gondola to holding area or to its final location as designated on your Detailed floor plan Using the Pull Chain PC is the easiest way to initiate movement of fixture Att
4. ed Failure to comply with these warnings could cause personal injury and or property damage Place Blue Streak Rollers BSR amp Braces BSCB in front of each section of the first gondolas to be moved a Be sure to verify compliance with load chart Failure to do so may damage the base brackets and could result in shelving collapse merchandise damage or injury Lift gondolas with the Gondola Handle BSH Place tip of handle behind the perpendicular base foot apply even downward pressure on handle a Always lift heavy side first when raising the gondola Lower the heavy side tast b Lift only as high as needed to place Blue Streak Roller BSR under shelf unit Ge Never Lift higher than 1 172 oneness The Lime Green tipped Jack Handle BSECH is to be used when an End Cap is attached on the left end of the gondola when you are unable to access the foot bracket with the standard Blue Jack Handle Use with the standard Blue Streak Roller Install the regular Blue Streak Rollers BSR from the right side of the foot bracket Move roller under the foots horizontal beam until the vertical stop on top of roller abuts the Horizontal beam of foot Slide roller out to front of fixture until the 2 square Connecting Brace pocket brackets on roller are positioned on the Sides of the perpendicular foot beam and flush with the front of the fixtures foot The Red Roller BSECR is used when an End Cap is attached on the right end of the gon
5. r the center of gravity and make the gondolas more stable during the move Gondola Load Chart Deck Depth Maximum Section Load 13 1400 lbs per side per section 16 1000 lbs 19 800 lbs 22 700 lbs 25 600 lbs 28 500 lbs 31 400 lbs Caution When a gondola has unequal deck depths on each side use the load limit on the deepest deck for both sides 8 You are now prepared to start moving your gondolas MOVING DAY WARNINGS Do not attempt to move shelving that does not have feet on both sides wall units Island shelving can be moved with the Gondola Train system Do not attempt to move shelving that is heavily weighted on one side and little or no weight on the other side Do not move if the height to foot ratio is more than 6 to 1 When de merchandising shelving to comply with load chart begin removing product from the top shelves first When placing Gondola Roller under gondolas Place hand fingers on the side behind the vertical stop opposite side of angle on top of roller Since the gondola will tip slightly during the lifting no one should stand on opposite side of gondola side being lifted Always lift the heavy side of gondola first to prevent potential instability during lifting Only one person should lift the gondola at a time Do not leave the Gondola Rollers under the gondolas for an extended length of time Rollers should be removed immediately after the gondola is relocat
6. this process until all merchandise is in its proper place reduces broken items damaged packages lost bin tags and is positioned merchandise THIS ENABLES ANY EMPLOYEE TO PROPERLY RESTOCK AND MERCHANDISE DURING THIS BUSY TIME EMPLOYEE AND MANAGEMENT S MORALE WILL REMAIN HIGH
Download Pdf Manuals
Related Search