English - Shopify
Contents
1. lt Ouick Lock TV bracket R y A 2 KU Screws A thru G Washer H used Quick Lock TV bracket R with screws A thru D Spacer J if necessary for curved TVs Diagram A WARNING AN Never over tighten a screw into the back of your flat panel TV Do not lay the TV face down on its glass front Use a wall or a TV stand Step 2 Mount Wall Plate Wood Stud Wall The Wall Plate can be mounted to three wood studs with 16 centers or to two wood studs with 24 centers Use a stud sensor to locate the studs clearly marking the outer edges of the studs Use a long level to ensure the holes are level at the desired height Pre drill the upper holes in the center of your studs and attach the Wall Plate to the wall using Lag Bolts K and Lag Bolt Washers I see Diagram B for three stud installation we recommend you center the plate if you have two 24 studs Do not over tighten lag bolts K Make sure the Wall Plate is flat against the wall surface Using the Wall Plate as template pre drill the bottom holes and secure using Lag Bolts K and Lag Bolt Washers I taking care not to over tighten Wood Brick or Concrete Wall Using the Wall Plate as a template mark six holes four toward the outer edge of the Wall Plate and two near the center at your desired height see Diagram C Adjust the Wall Plate position to be clear of mortar joints keeping in mind that2. the mount provides minor horizontal shift along the length of the Wall Plate Use a long level to ensure the six holes are level and at the desired height Pre drill six holes and insert a Concrete Anchor L into each of the holes flush with the concrete wall surface and not flush with the surface covering such as drywall Attach the Wall Plate using 6 Lag Bolts K and Lag Bolt Washers I see Diagram C Make sure the Wall Plate is flat against the wall surface Do not over tighten Lag Bolts K Concrete 3 75mm 3 75mm EM 7 16 11mm N a en y y o o L CA s Diagram B F l k w 7 7 Diagram C CAUTION CAUTION Make sure the supporting surface will support the load limits outlined in the Caution at bottom of page two Tighten Lag Bolts until the Wall Plate is snug flat against the wall Do not over tighten Lag Bolts K Each Lag Bolt must be located in the center of a wood stud Make sure the concrete or brick wall is at least 3 5 thick Make sure the anchor is seated completely flush with the concrete surface even if there is another layer of material such as drywall If drywall is over 5 8 thick custom lag bolts must be used Concrete must be a minimum of 2000psi in density Supporting your digital lifestyle CAUTION Read this section carefully prior to insta
3. which are expressly disclaimed The information in the owner s manual has been carefully checked and is believed to be accurate However Kanto assumes no responsibility for any inaccuracies that may be contained in the manual In no event will Kanto be liable for direct indirect special incidental or conseguential damages resulting from any defect or omission in this manual even if advised of the possibility of such damages www kantoav com sales kantoav com Tel 604 231 9574 Fax 604 231 9535
4. 35mm Screw Screw Screw Screw H Washer Lag Bolt Washer J Plastic Spacer K Lag Bolt R Quick Lock L Concrete Anchor TV Bracket Required Tools e 3 16 wood drill bit e hammer for concrete installs e 7 16 masonry bit for concrete installs e carpenter s level e Socket set e stud finder e Phillips screwdriver TM Supporting your digital lifestyle Step 1 Attach TV Brackets There are a wide variety of TVs available offering an assortment of screw sizes We provide a selection of mounting screws to fit most TVs If you have any concerns about this mounting hardware or installation call us direct at 1 888 848 2643 or email at support kantoav com Step 1 1 Select the correct size of bolt Step 1 2 Attach TV bracket arms to the back of the TV Kanto provides 3 bolt diameters Metric sizes M5 M and Now that you have selected the correct bolt length it s M8 in various lengths time to attach the arms to the TV as shown in Diagram Part items A B C D E F or G A Use the washer H for bolts A D sizes M5 and M6 The Select the correct diameter screw and hand screw into washer will work for both screw sizes the back of the TV to determine the correct length Use the longest available bolt without reaching the bottom of Please note The washer is not reguired for M8 size bolts the TV threads E F amp G If your TV has a curved back you can use the spacers J
5. English User Manual F6080 TV Mount FIXED FLAT PANEL TV MOUNT 400 x 400 1100 x 600 200 Ibs VERRE ni 91 kg Supporting your digital lifestyle Table of Contents Table of Contents Introduction 2 Setup Steps 3 to 4 6 Supplied Parts amp Hardware 3 Other Kanto Produtt amp va vse eee ees 7 Setup Step ass tee tea cena wiw Ra a 4 Ynn Y te ao a aes an 8 Setup Step 2n ea WYW YY Y YA Y Y WR 5 Introduction Thank you for choosing a Kanto AV Systems wall mount The F6080 is designed to mount flat panel televisions weighing up to 200 lbs 91 kg within 1 of your wall Read these instructions fully before installation of this mount If you do not understand these directions or have any doubts about the safety of the installation please consult a qualified installation contractor to install this mount Make sure there are no defective or missing parts Do not use defective parts If you are uncertain whether the part is defective call Kanto AV Systems directly at 1 888 848 2643 or support amp kantoav com Kanto AV Systems can not be liable for property damage or injury caused by incorrect mounting incorrect assembly lifting or incorrect use of this product This product should not be m
6. ll Step 3 Attach TV to Wall Plate With the TV brackets firmly secured to the TV use two For minor level adjustment you can adjust the two top people to lift the TV into position and hook the TV brackets screws using a Phillips screwdriver to ensure the TV hangs onto the wall plate as shown in Diagram D The two spring loaded Ouick Lock brackets will snap into place as you lower the bottom of the TV onto the plate level as shown in Diagram E If you need to release pressure on the screws pull down slightly on the Ouick Release cords as shown in Diagram F N h Wes Level es Loosen lt Hook x i i U UJ Pull Cord to Release Diagram D Diagram E Diagram F Step 4 Release the TV Because the TV sits so close to your wall the Quick Lock TV brackets are equipped with quick release cords Loosen the top levelling screws slightly to release tension then simply pull to release both Quick Locks as shown in Diagram F and pull the bottom of the TV away from the wall Then using two people lift the TV up and away from the wall plate WARNING Use two people to lift and position the TV onto the Wall Plate Kanto as Check out more great products from Kanto Kanto YARO Speaker System Our stunning new audio system designed for Apple TV e Utilizing audio technology by Bang amp Olufsen ICEpower 100 watts of pure clean sound Optional 200 watt s
7. ounted on steel stud walls or cinder block walls Consult a qualified installation contractor if you are unsure about the type of wall you may have We make every effort to ensure all necessary hardware is included If there is hardware missing please call Kanto AV Systems directly at 1 888 848 2643 or support kantoav com See installation video online at www kantoav com pages video f6080 CAUTION The maximum loading weight is 200 Ibs 91 kg This wall mount is intended for use only within the maximum weight restrictions indicated Use with products heavier than the maximum weights indicated may result in instability causing possible injury Recommended TV Size 60 inch to 80 inch CAUTION The wall you plan to affix the Kanto mount to must be able to support more than 5 times the weight of the television and the wall mount combined Do not use this product for any purpose other than to mount a flat panel TV on a vertical surface as outlined in this manual Improper installation may cause damage to your TV or serious injury This product should not be mounted to steel stud walls cinder block or old concrete walls Consult a gualified installation contractor if you are unsure about the type of wall you may have Supplied Parts and Hardware Wall Plate B x4 x4 7 x4 A M5 x 15mm B M5 x 25mm C M6 x 15mm Screw Screw Screw GE x4 7 x4 x4 D M6 x 25mm E M8 x 15mm F M8 x 25mm G M8 x
8. ub woofer Visit kantospeakers com for more Kanto Infinity Series Cables 3D and 1080p HD Full Colour Capabilities e 24 kt gold plated contacts Metal head connectors with flex relief and grip e HDMI Ethernet Channel For more TV and desktop mounts along with our other products please visit kantoav com LIKE Kanto on Facebook to receive upcoming news and special product offers Supporting your digital lifestyle Warranty Limited Warranty To Original Purchaser Kanto AV Systems Kanto warrants the equipment it manufactures to be free from defects in material and workmanship for the following limited warranty period of 24 months parts and labour If equipment fails because of such defects and Kanto or an authorized dealer is notified within 24 months from the date of shipment with proof of original invoice Kanto will at its option repair or replace the eguipment provided that the eguipment has not been subjected to mechanical electrical or other abuse or modifications Eguipment that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the repair Such repairs are warranted for 90 days from the day of reshipment to the original purchaser This warranty is in lieu of all other warranties expressed or implied including without limitation any implied warranty or merchantability or fitness for any particular purpose all of
Download Pdf Manuals
Related Search