panda easyfit
Contents
1. INSTALLATION Only dealers in the rehabilitation industry and specialist car adaptation companies are allowed to integrate the Panda Easyfit into vehicles In order to avoid incorrect installation this manual must be followed step by step Incorrect installation can cause dangerous and life threatening situations If you have any doubts regarding the integration of the Panda Easyfit into your vehicle you should contact your local dealer or the importer or manufacturer The shape of the frame and the method of installation may leave marks in the upholstery over time To avoid this you may want to place protection pads or positioning pads available throughout your dealer on your seat and back Also in some cases the guide plate may have to be shortened in order to close the rear door properly IMPORTANT It is very important to choose a Panda seat in the right size to suit your child If in doubt contact your local dealer Always keep the Panda Easyfit secure using the vehicle s three point seat belt even when the child is not using the car seat so it can not be flung through the vehicle in case of a collision The Evo bracing strap or Easyfit mounting system alone is not enough It is not allowed to modify the Panda Easyfit Any modification will lead to the Panda Easyfit losing its ECE 44 04 certificate Should any modification be necessary in con nection with the particular handicap of your child please su2. ges only Furthermore R82 offers a warranty against defects in manufacturing and materials according to the national rules and regulations or as Stated in the sales and delivery terms from the dealer where the product is purchased These could include the fact that the warranty could be affected by the customers responsibility of servicing and maintaining the product according to the intervals prescribed in the manual The warranty can only be sustained if the R82 product is in use in the same country where it was purchased and if the product can be identi fied by the serial number and also that all condi tions of customer responsibility have been met The warranty does not cover accidental damage including damage caused by misuse or neglect The warranty does not extend to non durable parts which are subject to normal wear and tear and need periodic replacement The warranty is null and void if non original R82 parts acces sories are used or if the product is repaired or changed by anyone other than an authorized R82 representative R82 reserve the right to inspect the product being claimed for and the relevant documenta tion before agreeing the warranty claim The warranty is given by the R82 dealer or sub sequently an R82 representative MAINTENANCE The metal parts of the Panda Easyfit can best be cleaned with a moist cloth The upholstery of the Panda seat can be washed in accordance with the instructions on the sewn in la
3. Check if the Panda Easyfit is in horizontal position If not repeat steps 4 5 and 6 Check if the Panda Easyfit works properly and if it locks both in swing out position and in its starting position in the vehicle You should hear a clear click Removal from the vehicle 1 Dismount the Panda Easyfit by pulling back wards the two horizontal orange triggers E on the catch arms C This will unlock the Easyfit mounting system from the Isofix an chorage points of the car Take out carefully the Panda Easyfit and place itin a safe place with the positioning pads between the seat and the frame The wedge pad should be under the seat PANDA EASYFIT WITH EVO BRACING STRAP Installation in the vehicle with straps 1 Mount the two bracing strap holders F on 8 Loosen the Allen screws of the adjustment legs of the Panda Easyfit The legs will slide the Easyfit frame for the right position of the Evo bracing strap 2 Remove the rear seat from the vehicle or fold it forward to access the seat belt mounting points On the right side or depending on the model on the left side disassemble the two fixing plates of the 3 point seat belt that are fixed to the bottom of the car down to the bottom of the car When both legs are completely down tighten the Allen screws again Lead the bracing strap over the tube frame in front of the bracing strap holder F and insert it into the adjustment bu
4. The straps must be mounted through the back cushion at the correct shoulder height B led backwards over the hips C and then be fixed 1 Place your child against the back of the car seat Loosen the shoulder straps completely by pushing in the white buttons D on the rolling mechanisms and moving these me chanisms forward This allows your child to move his or her arms underneath the shoulder straps more easily 2 Take the plastic crotch strap buckle E and push the lap strap tongue plates into the buck le Now push in the white buttons of the rol ling mechanisms so that the shoulder straps roll up and are tightened Check whether the 5 point fixation belt fits your child well 3 Now place the vehicle s 3 point seat belt F across your child and lock it Make sure that the lap and diagonal straps are correctly po sitioned The left and right rolling mechanisms D are deliberately positioned at different heights to ensure that the diagonal strap can be led between them Make sure that the diagonal strap does not run over either of the rolling mechanisms If any other fixation system is used in the Panda Easyfit this will lead to the ECE 44 04 certificate being lost PRODUCT IDENTIFICATION A CE mark Product identification B Manufacturer this label is attached to the inside of the lower frame C Serial number this label is attached to the inside of the lower frame D Class and approval number t
5. model It is not possible to rebuild the Easyfit frame from left to right swing out The Panda Easyfit is approved according to the most recent European ECE 44 04 requirements and is side Impact tested to the ISO DIS 14646 norm ABOUT ISOFIX The Panda Easyfit with the Easyfit mounting sy stem makes use of the ISOFIX anchorage points in the vehicle and the child needs to be securely strapped in the 3 point safety belt of the vehicle In this way you can count on the optimum force distribution during a collision also sideways Due to the optimum place of the 3 point safety belt that will protect the child together with the Side Impact headrest ISOFIX is a firm way of fixation with regulated anchorage points for safe and easy mounting of car seats in vehicles It has become the inter national standard for all car manufacturers and car seat producers This way of anchoring the car seat with catch arms A minimizes mistakes when mounting the car seat on the rear seat of the car It also optimizes the protection by the fixed way of mounting between the car seat and the vehicle The adjustment legs of the Easyfit frame B will help to keep it fixed in the right position also during a collision According to the European regulations since February 2006 new car models should be equipped with ISOFIX on at least two rear seats And from February 2011 all new cars should be equipped with ISOFIX on the two outer rear seats
6. Rac panda easufiF English user manual 2010 R82 A S All rights reserved The R82 logo is registered trademark of R82 A S 02 2011 CONTENTS lg ecc deme m 3 PDOBEISOIDG ic 4 lieta Miss cress acr aad Ct o 5 a TNR AA 6 SAO eee O E ri MV MANY ERR EET eee ia 8 Mainlenatice iaa 8 Panda Easyfit with Easyfit mounting system 9 Panda Easyfit with Evo bracing strap 10 Using the Panda Easyfit sind 11 gis T I 12 Other size of Panda seat for Panda Easyfit 13 as AA o S 14 Product Identification a 15 Description of Panda Easyfit parts 16 Measurement nenne nee 17 Technical Ataca 17 RA AC UNG Tirana ii ai c 17 PANDA EASYFIT The Panda Easyfit is a car seat designed for children with a body weight of 9 to 36 kg The Panda seat 4 sizes on the Easyfit frame can be turned and slid partly out of the car This to make it easier to transfer physically and or mentally challenged children into and out of the vehicle The Panda seat on the Easyfit frame has a tilt in space between 15 30 degrees The Panda Easyfit is available with two different mounting systems EasyFit mounting system for rear seats in a 4 door vehicle with a Isofix anchorage system on the outer rear seats or e Evo bracing strap system for cars without the Isofix system Both systems are available in a right or left swing out
7. bel Do not use any cleaning materials con taining chlorine or methylated spirit or any abrasive products Adjustments which are not described in this manual may only be made by authorized R82 personnel PANDA EASYFIT WITH EASYFIT MOUNTING SYSTEM Installation in the vehicle with Isofix il Mount the Easyfit system on the Easyfit frame with the 4 screws A Before mounting the Panda Easyfit it is ne eded to extend the Easyfit mounting system F towards the frame of the Panda Easyfit G as much as possible Pull the central orange knob B up and pull out the Easyfit system Cover the seat of the car with the protection pad to prevent pressure spots on the seat Place the Panda Easyfit on the seat of the car and slide both catch arms C of the Easyfit mounting system onto the Isofix anchorage points till both catch arms are locked with a clear click Pull the central orange knob B up and move the Panda Easyfit simultaneous to the back of the car seat Let the central orange knob B loose when the shortest position is reached of the positioning tube H This length will vary depending on the length of the seat of the car With this action you will position the Panda Easyfit in your car Loosen the Allen bolts of the adjustment legs D of the Panda Easyfit The legs will slide down to the bottom of the car When both legs are completely down tighten the Allen bolts again
8. bmit a request for dispensa tion to the appropriate competent authority Never leave your child alone or unattended in your vehicle Lead the three point seat belt correctly across the child s shoulder and hips Make sure that the lap section does not run across the child s stomach Make sure that the straps run tightly across the child s body The Panda Easyfit has to be turned back in and locked during transport and strapped with the 3 point belt from the vehicle Ensure that no parts of the Panda Easyfit are damaged during use Have the Panda Easyfit checked if it does not perform properly The metal parts of the Panda Easyfit may become hot in the sun Therefore contact between skin and the metal parts has to be avoided as it may cause blisters After an accident the Panda Easyfit may be damaged even if not visible Have the Panda Easyfit frame car seat and bracing strap checked and replace it if necessary The Panda Easyfit may be fitted with original accessories and parts only otherwise the certificate will be void There are several accessories available such as a 5 point fixation belt thickened side cushions protection pads positioning pads multiple headrests and a footrest Standard Panda accessories must not be used because the certificate would then be lost Luggage has to be properly stored and secu red during transport as it may be flung across the vehicle during a sudden stop and cause serious
9. ck the 3 point seat belt D Lead the diagonal strap through either the lower or the higher strap guide depending on the height of your child s shoulder Ensure that the strap does not run too closely to the neck nor too low below the shoulder see drawing For extra comfort you may want to provide the diagonal strap with a protective cover at neck level or the low side of the guidance holder depending on how it fits the child s shoulder see drawing FOOTREST Slide the footrest into the holder on the lower front frame tube of the Panda Easyfit Fasten the footrest with the handle The footrest can fold up and its angle can be adjusted using the turning knob in the front The height can be adjusted by loosening the hexagon head bolt sliding the footrest to the desired height and bolting it down again If the footrest is positioned too high the turning section will touch on the footrest So in such a position the footrest cannot be used OTHER SIZE OF PANDA SEAT FOR PANDA EASYFIT If you change the size of the seat you also need to change the adapter Please follow instructions below Unscrew the Italian handle 37 totally Pull the front mounting rod 36 totally out of the adapter tube take care that the metal washers and plastic bearing bushes stay together Remove the plastic covers from the nuts on the rear mounting rod 35 Lossen the nut and remove the rear mounting r
10. ckle D inside out Pull until the tensioning element the ratchet C has enough room to be tensioned 10 Check if the Panda Easyfit is in horizontal position If not repeat steps 7 8 and 9 3 With front seat installation disassemble the two fixing points of the lap belt section that are fixed to the car s floor or to the front pas senger seat If in doubt as to whether these points are suitable for fixing the Panda Easy fit please contact the car dealer or importer distributor Removal from the vehicle 1 Dismount the Panda Easyfit by unlocking the adjustment buckle D so the bracing strap can be released After this the tensioning element ratchet C can be opened and the bracing strap can be pulled out 2 Take out carefully the Panda Easyfit and place it in a safe place 4 Mount the fixing plates A and B of the Evo bracing strap E underneath the existing fixing plates of the 3 point seat belt Ensure that the tensioning element the ratchet C is located to the right with right hand instal lation or to the left with left hand installation so that the Panda Easyfit when turned out ward will not touch the ratchet C When tighting the bolts to the chassis of the vehicle normally a torque wrench is needed please find the correct moment of force in the instruction manual from the car or ask at the local garage After mounting the fixing pla tes of the bracing strap the effective thread len
11. gths of the strap fixing bolts must be at least 1 5 times the length that goes through the nut Now tighten these bolts with the appropriate torque to prevent them from being loosened by vibration 7 Position the Panda Easyfit on the seat e g USING THE PANDA EASYFIT Pull the handle until it is released and pull the Panda Easyfit slightly outward Turn the Panda seat outwards by 90 and pull the Panda Easy fit further until it locks into position with a clear click Place your child firmly against the back of the Panda Easyfit You may want to give your child extra support with a 5 point fixation belt acces sory Unlock the Panda Easyfit by pulling the handle again and slide and turn the seat with your child in it into the car returning it to its original position with a clear click Before the Panda Easyfit locks turn it back into the forward facing position and push it further inwards until it clicks into its locked position The following instructions must be strictly fol lowed Place the child firmly against the back of the car seat so you can lead the 3 point seat belt across the front of your child properly The 5 point fixation belt must have been fixed correctly Lead the diagonal strap through the strap guide B across the shoulder of your child Lay the lap strap over your child s hips in between the back and the seat C Now push the tongue plate into the buckle to lo
12. his label is at tached to the outside of the seat under the seat belt guide PEEREBOOM Spieringweg 931 2136 LK Zwaanshoek The Netherlands T 31 0 23 561 73 19 F 31 0 23 563 94 99 E info peereboom com A CE id I www peereboom com OD MAX 9 36 KG X 31 0 23 561 73 19 Type PSOS Version ECE R44 04 SN xxxxxxxx E 10 06 2006 Parallelvej 3 DK 8751 Gedved Date 31 01 02 Load 36 kg Serial number XX X rti cle number XXXXXX 5707292 134158 EASYFIT EN BASIC ECE R44 04 SPECIAL NEEDS 9 36 KG 044436095 000002 DESCRIPTION OF PANDA EASYFIT PARTS 1 Car Seat Easyfit frame left or right 3 Adapter Easyfit 4 sizes 7 Side Impact headrest 8 Cover for side Impact headrest 9 Panda Car Seat 4 sizes 13 Strap guide left or right 16 Easyfit headrest fixing plate 17 Evo bracing strap holder only with Evo bracing strap 35 Mounting rod back 36 Mounting rod front 38 Adjustment legs L 13 eh A u 7 MEASUREMENTS Seat Width A Seat depth B Back height C Tilt in space D Total width G Total length H Seat height back Total height I Panda 2 8 7 24 cm 17 cm 914 6 39 cm 15 20 35 15 30 45 cm 17 58 cm 22 16 cm 6 Total weight 85 cm 33 Min load 18 kg 39 Ib Max load 9 kg 1924 Ib 36 kg 79 Ib Frame Steel powder coated Shell ABS Foam Fire resis
13. injury to the vehicle s occupants SAFETY The Panda Easyfit has the CE mark and is ECE 44 04 certified This means that this product meets all relevant European safety require ments This car seat belongs to the category Special Needs Restraints for groups 1 2 and 3 9 36kg The Panda Easyfit is approved for use in the rear seat and the front passenger seat of ve hicles These seats have to be equipped with ECE approved 3 point lap and diagonal seat belts The safest place for installing the Panda Easyfit is the left hand rear seat of the vehicle pavement side If installation in the front pas senger seat is chosen the airbag if any must be deactivated This is to be done by an official car dealer After installing and tightening the bracing strap do not move the front passenger seat any more otherwise the bracing strap will not be positioned correctly No alterations may be made to the Panda Easyfit as these would lead to the ECE 44 04 certificate being void Should any modification be necessary in connection with the particular handicap of your child the parents should sub mit a request for dispensation to the competent authority and the orange ECE sticker must be removed Never leave your child unattended in this product Ensure permanent supervision by an adult Make sure that all fixations are fitted cor rectly and checked frequently WARRANTY R82 offers a 5 year warranty on frame breaka
14. od 35 totally take care that the plastic washers and plastic bearing bushes stay together The adapter 3 with the Panda seat unit is separated now and can be removed Place the new adapter with the other size Panda seat unit between the Easyfit frame and place the rear mounting rod 35 through the adapter tube take care that the plastic bearing bushes and washers are in the right position again Mount the nut on the rear mounting rod 35 and do not tighten this nut too much adapter 3 should move freely through the slots Place the two plastic caps on the nuts Place the front mounting rod 36 in the adapter tube and tighten the Italian handle take care that the plastic bearing bushes and washers are in the right position again IMPORTANT The plastic washers should be mounted on the rear mounting rod 35 and the thick metal washers should be mounted on the front mounting rod 36 5 POINT FIXATION BELT The 5 point fixation system is specially designed for the Panda Easyfit being the only additional fixation that is allowed for this car seat The 5 point fixation belt is NOT a safety belt it is merely intended to support your child in the right position in the car seat ALWAYS use the vehicle s 3 point lap and diagonal seat belt even when the child is not in the car seat The 5 point fixation belt is mounted in the car seat with 6 fixlock clips that are slid across the straps
15. tant polyurethane Fabric Fire resistant Trevira CS Panda 275 2 Panda East cm PandePEday ft cm 9 814 28 cm 24 cm 11 9 41 cm 16 20 35 15 30 45 cm 17 58 cm 22 16 cm 6 85 cm 33 19 kg 41 Ib 9 kg 19 Ib 36 kg 79 Ib Panda 3 2 Panas Edeym 11 9 31 cm 27 cm 12 10 44 cm 17 20 35 15 30 45 cm 17 58 cm 22 16 cm 6 85 cm 33 19 kg 41 Ib 9 kg 19 Ib 36 kg 79 Ib Panda 4 2 PAR t 1292 445 36 cm 31 cm 14 127 52 cm 20 20 35 15 30 45 cm 17 58 cm 22 16 cm 6 85 cm 33 20 kg 44 Ib 9 kg 19 Ib 36 kg 79 Ib MANUFACTURER R82 A S Parallelvej 3 DK 8751 Gedved 17
Download Pdf Manuals
Related Search