The operation of the stair lift Konstanz
Contents
1. The control lamps on the loading device show the respective status of the loading device Thereby two different designs of the loading device must be distinguished A main feature is the number of light diodes Battery fully charged On On extinguishes briefly Off every 2 seconds Note If the Lift outside of the stopping point is not charged 30 seconds after the last motor motion an acoustical signal sounds Operator manual Konstanz STG ASA 11 20 Version 8 0 01 2010 4 5 Retrieving and sending of the platform standard design Make certain before every trip that the acoustical and if present the visual optional warning signals are functioning The platform lift Konstanz can be retrieved from every stopping point or sent to another stopping point For this the key switch at the corresponding stopping point should be inserted and turned in the corresponding direction and held firmly in this position The platform lift does not respond immediately but rather after a delay of around 2 seconds Comment The lift travels from the external control points only when folded together 1 e the floor of the platform must be folded up and the safety gates must be folded down Note An LED 1s attached to the transmitter for the retrieving and sending of the chair lift GREEN Batteries are in order ORANGE Battery power is decreasing replace batteries when convenient RED Battery power is very weak replace batteries immediat2. EA 17 5 OTOT EEA DDA E a S E EE S E N I ETE 18 5 1 PETG TO NIAS Sodien e E E ene ate 18 Ded PCCM TOSI Cy Call ireren steals and cnn Mog ise tative tiadav dels AE EER 18 5 3 Tie lateralriv GAUL dO sas eter eutehctan lati t hed G a kadeat a dada oleate th ia arts 18 IA INCOUSTIC O PMC Al 51 OMA ee E etude seeks 18 6 Wh n malfunctions OCCU sicisisecccsiceccscscdececesscsssdscsasescaccusssccscdesecesssossdccseoosceseeeess 19 7 ACOUSUC warnine sionals scssssisssiecssein eses nekain aiaa saaan aa aia asia 19 8 Services for your platform lift at a glanCe eecooosssssseccccccssssesecessssssesosoeo 20 Important Please read the operator manual before using the lift Make certain that every user of the lift has read and understood the operator manual The manufacturer assumes no liability for errors in the operator manual Operator manual Konstanz STG ASA 1 20 Version 8 0 01 2010 EL EU conformity declaration for machines EU guideline machines 2006 42 EG Herewith the manufacturer declares Lippe Lift and Anlagenbau GmbH WeststraBe 48 32657 Lemgo that the machine Stair inclined lift Platform lift Type Konstanz conforms to the stipulations of the aforementioned guideline conforms to the stipulations of the following additional guidelines EMV guideline 2004 108 EG Low voltage guideline 2006 95 EG following harmonized standards are applied or their protective goals were achieved E
3. N 81 40 2009 EN 349 2008 EN ISO 12100 1 2004 EN ISO 12100 2 2004 EN ISO 13850 2007 EN ISO 13857 2008 EN ISO 14121 1 2008 EN 60204 1 2007 following reported position TUeV AUSTRIA SERVICES GMBH ID Nr 0408 included was for EU model test Test report no TUeV A MHF MG 09 06960 Responsible for documentation Lippe Lift and Anlagenbau GmbH Documentation department Weststrabe 48 32657 Lemgo Lemgo 15 03 2010 F W Mueller Managing director Operator manual Konstanz STG ASA 2 20 Version 8 0 01 2010 1 General The nameplate reflects the most important information about the platform lift Machine type Type designatio Treppenschragaufzug EN81 40 Year of construction Typ Konstanz Baujahr 2010 biai b Fabriknr T 03000 abrication number Tragfahigkeit KG 300 Eigengewicht KG 185 as Load carrying capacity of the Lippe Lift und Anlagenbau GmbH platform Weststrake 48 pa ie ca Weight of the ax D 32657 Lemgo www lippelift de platform Manufacturer Field for the input of the importer specialized retailer Operator manual Konstanz STG ASA 3 20 Version 8 0 01 2010 The platform lift Konstanz 1s equipped with many sensitive surfaces Here an overview 1 Lies in the safety circuit when activated no further driving is possible 2 Direction oriented switch off it can be driven in the opposite direction 3 Lies in the safety circuit when activated no further
4. This is a translation of the original German operating instructions The operation of the stair lift Konstanz Contents Page 1 CSOT CH I E E E T T A O TE eS 1 1 TSC MINI AW HACE geass eia A A A A go 2 _OUTPOUNGING Conditions seresa E E O E E ERSS K CSP ODIO ALOIS sarin tad tina vaseiaciiaet S a 2 l tended PUD OSC iiceoe ease eE NESE EE eS 2 1 Conveyance PROLCS cis 2 sista het aeaa tg ine et rican arcitie contadcaa Sat ne ei tuluaes et atten doen tate 2D Zed MINIPTODER USAC e inns iseatauiias sues aden ee etnan erence cee 6 29 WISER GUANTICAMON ass E EEE TS 6 ZA PRODUCT GESCEIP OM a vssc cass e bared oE ea eTa A O A Tra OAN 6 2 5 Overview sketch of the platform UMftasmscisitreseana a E Sa et ed 3 Sal y asin drae a tiadusteerunaae 9 4 Operaio eanna a O A 11 4 1 EIMS WAN anane a a aae ae eee a Il 4 2 The deep unloading protection and loading cccssesseeseeseeeeecceeeeeeeeeeeeeaaaaas 11 43 21 66 lt 6 1 cal 07216 0 2a ne ee 11 Ad ENE TOA GINS deViCO inician ena E E ATEA ts Il 4 5 Gettine and sending OF the platlOrim seeren e EEO ots I2 5 4 OY A maie Daoa E a a ween SOOR 13 IHO Manual PIONIE oien a E E A E E AEA 13 a6 Drvna with he plac O ennnen a ATG 14 4 7 What do you do in the case of an unexpected Stoppage cccccsssssessseeeeeeees 14 TAOL Hand WHEE opera Onesia a a oa easitiese AN 15 T402 Evac aton metal COVEN hortara aaae E EAA EEEE 16 HAOS Evacuation Plastic COVEN espirais oiee ati E Lene E
5. ailable with seatbelt 11 Cover for motor controls 12 Rightascension flap S 13 Contactfloor S 14 Safetybar S 15 Side ascension flap Alternative to item 14 Emergency unlocking o o Emergency unlocking Pos fi 10 11 12 13 14 15 Operator manual Konstanz STG ASA 8 20 Version 8 0 01 2010 gt gt bP P PP PP PP PB Safety and special hints Caution Although your lift conforms to the latest safety directives absolutely observe the following safety hints Commission the lift only after reading the operator manual and comply with the operating instructions Never exceed the allowable load carrying capacity Residual hazard breakage failure of the breaks Only operate the lift when sitting see conveyance profile for exceptions Do not use the lift in case of fire Do not bring any loose or hanging pieces of clothing into the area of the track and platform when the lift is moving Residual hazard hanging from loose clothing etc Fold the lift together when not in use Residual hazard risk of tripping Never place your hands near the rails when the lift is moving Residual hazard risk of crushing Always face the track in the travel direction during travel Residual hazard risk of crushing Do not remove separate deform or forcefully operate and lift parts paneling parts or operator elements Do not operate the gates with force either during travel or when folding up o
6. and down electrically This occurs by means of an UP or DOWN command from see also item 4 5 or via the internal controls for special design 2 The command must be held down so called inching operation until the folding process is ended If a malfunction is present during the folding process then the platform must be folded together or unfolded manually see item 4 5 2 and customer service must be informed The manual platform The folding process on a step may only be carried out by an assistant In order to fold down the platform manually one should proceed as follows a Bring the safety gates into a horizontal position b Fold up the platform floors c Fold the safety gates downwards against the platform floor The respective gate on the lower floor is accordingly designed longer in order to enable safe operation In order to unfold the platform again one should proceed in reverse order and in conclusion fold up the safety gate of the desired access point to a completely upright vertical position Operator manual Konstanz STG ASA 13 20 Version 8 0 01 2010 4 6 4 7 Travel with the platform lift standard design Make certain before every trip that the acoustical and if present the visual option warning signals are functioning The following control elements are located on the platform a Key switch Function I and 0 S 7 8 item 2 b Control part Function UP and DOWN S 7 8 item1 c Push but
7. bed above in a to d however the hand wheel must first be turned to UP until the lift has moved approx 5 cm on the track then the hand wheel can be turned in the direction DOWN Operator manual Konstanz STG ASA 15 20 Version 8 0 01 2010 4 7 2 Evacuation only by technical personnel Version with metal cover In order to help the operator from the lift one should proceed as follows e Press the EMERGENCY OFF button on the platform S 7 S tem3 e Loosen the fastening screws on the cover Tools delivered in the envelope e The platform cover S 7 8 item5 must be folded up and secured against falling down by raising the lever to lock see sketch below e A red marked Bowden cable is found on the upper side which should be pulled in the direction of the operator In the process the upper safety gates can be folded up at the same time manually e Now the operator can be helped out of the lift on the upper side The platform should be folded up manually so that the lift does not block the stair access See 4 5 2 Lever Bowden cable marked in red Operator manual Konstanz STG ASA 16 20 Version 8 0 01 2010 4 7 3 Evacuation only by technical personnel Version with plastic cover In order to help the operator from the lift one should proceed as follows e Press the EMERGENCY OFF button on the platform S 7 8 tem3 e Remove the cover cap on the top side on the front paneling by means of a screw driver o
8. discharge protection and charging The platform lift Konstanz is equipped with automatic charging devices The charging occurs automatically when the platform lift drives to a charging station The batteries require no maintenance All platform lifts Konstanz are equipped with an acoustical total discharge protection This acoutistical signal device should protect the batteries against total discharge If the battery voltage falls below 22 V a beeping sound occurs in approx 5 sec intervals In this case you should drive immediately to the nearest if possible the lower charging station and charge the lift for several hours this occurs automatically at the charging site The beeping sound ceases after proper charging The sound can be stopped by pressing the emergency off switch This has no influence on the loading process Control of the loading The platform lift Konstanz is equipped with an overloading protection acoustically and optically For the metal cover the orange lamp is extinguished on the cover S 7 item L2 and for the plastic cover the background lighting is extinguished S 8 Pos In the case of overloading an additional continuous tone 1s transmitted by the internal beeper As a basis the entire loading process takes place in the middle of the platform floor If the overloading protection reacts reduce the weight Possibly positioning closer to the direction of the track is sufficient The loading device control lamps
9. driving is possible Operator manual Konstanz STG ASA 4 20 Version 8 0 01 2010 1 1 Technical data Allowable load carrying capacity max 300 Kg Continuous audio pressure level lt 70 dB A Vibrations lt 0 5 m s Measurement uncertainty 3 Speed ca 0 1 m s Platform voltage 24VDC Loading device voltage 230VAC 55W 1 2 Conditions of the surroundings Temperature range 20 C to 60 C Rel humidity max 100 1 3 Test obligations Whether the platform lift Konstanz is subject to an obligatory test depends on the respective national regulations and lies in the responsibility of the operator These must absolutely be checked and maintained In Germany a test obligation applies for systems with a conveyance height gt 3m In any case evidence must be provided and documented before the initial usage in accordance with EN81 40 The platform lift is subject to at least annual maintenance in accordance with the maintenance manual We recommend concluding a maintenance agreement with your specialized company 2 Intended purpose The platform lift 1s intended for the transport of wheel chair occupants or persons with restricted mobility The platform travels between specified access points on a firmly installed rail which is designed straightly The platform is guided by the rail over a stairway or an accessible inclined surface Only instructed persons may operate the system 2 1 Following conveyer profiles are pla
10. ely Retrieving and sending of the platform lift Special design 1 using the external control device only with key switch with 3 settings S 7 8 item 2 for travel with opened platform via the external control device This option must be activated by a technical specialist within the control system It must be ensured that no third person can land spring onto the travel route Condition Travel area is 100 visible The key switch S 7 8 item 2 must be set to position II otherwise as in 4 5 Retrieving and sending of the platform lift Special design 2 using the internal control only for key switch with 3 settings S 7 8 item 2 This option must be activated within the control system by a technical specialist Using the internal controls the platform can be driven into the folded down position For this the key switch S 7 8 item 2 must be set to position II Now the platform lift can be driven using the internal controls S 7 8 item 1 In the case of more than two stopping points The platform lift will stop automatically at each intermediate stopping point and possible fold out in the case of an automatic platform If this is not desired then a new travel command should be given and the platform lift drives on Operator manual Konstanz STG ASA 12 20 Version 8 0 01 2010 4 5 1 4 5 2 The automatic platform With the automatic platform the floor folds up or down electrically as well as the safety gates fold up
11. hereby the assistant gives the driving commands Furthermore the user must have read and understood the operator manual Production description Our products combine in a suitable manner the requirements of overcoming the stairs with the outstanding integration with one s usual environment On the one hand the upper track pipe can be used as a hand rail on the other hand the platform and track are painted to your desired color from an extensive RAL color pallet The track does not need to be lubricated whereby undesired contamination 1s excluded The allowable load carrying capacity is 300 Kg measuring point for this is the middle of the platform floor The continuous sound pressure level is below 70 dB A We recommend concluding a maintenance agreement This guarantees by means of routine maintenance the technically optimal condition of your stair lift Konstanz The maintenance interval is at least annually Operator manual Konstanz STG ASA 6 20 Version 8 0 01 2010 Platform lift with metal cover front paneling 3 7 Pos Designation S e 6 Main switch located inside 8 Emergencycall S 9 Leftsafety gates S Operator manual Konstanz STG ASA 7 20 Version 8 0 01 2010 Platform lift with plastic cover front paneling Control unit Key switch Control unit on the spiral cable Option 5 6 Main switch located inside S 7 Holdingrod S 8 Emergencycal o 9 Leftsafety gates S 10 Folding seat optionally av
12. l with the platform lift special design 2 The key switch S 7 8 item 2 should be set to I otherwise as described in the standard design What is to be done in the event of an unexpected downtime such as a power failure We recommend installing a functional cell phone for contacting rescue workers Operator manual Konstanz STG ASA 14 20 Version 8 0 01 2010 4 7 1 Manual operation operating with hand wheel The stair lift Konstanz can also be operated manually Manual operation should be carried out by technical specialists Here one should proceed as follows a Press the EMERGENCY OFF button on the platform S 7 S tem3 b The screwed connections on the motor cover should be loosened with an Allen wrench delivered in an envelope c The motor cover should be folded up see image below d The brake ventilation lever should be pressed forward or backwards and simultaneously the hand wheel must be rotated on the shaft end of the motor image below In the process the lower stopping point should always be driven up to less force expenditure when turning the hand wheel The respective rotational direction should be directly specified on the hand wheel Note In case the cause of the downtime is not clear one should assume that the safety catch was triggered and its safety switch has led to the deactivation of the lift The safety catch may only be reset by technical personnel In this case one should proceed as descri
13. nned 1 Transport of a person sitting in a wheel chair 2 Transport of a person sitting on a folding chair 3 Transport of a person standing on the platform insofar as sufficient head clearance exists the person has sufficient standing stability and can securely hold onto the hand rails Separate document set required upon request 4 Transport of an additional person insofar as there is sufficient space on the platform and the allowable load carrying capacity is not exceeded Operator manual Konstanz STG ASA 5 20 Version 8 0 01 2010 A usage profile of 10 start ups per hour is planned for travel distances of at least 15m per start up In the case of longer travel routes correspondingly linear fewer start ups The platform lift Konstanz may only be operated if a hazard due to falling objects e g flower pot is excluded 2 2 An improper usage must be excluded e g e Exclusive usage for loads if in rare cases loads such as groceries or beverage crates are transported stability must be ensured and the load carrying capacity not exceeded e Loads which protrude beyond the open floor may generally not be transported e g large pieces of furniture e The platform lift Konstanz is not a toy children e Operation in explosive atmospheres 2 3 User qualification 2 4 The user of the platform lift must possess unrestricted mental faculties Users with serious visual restriction may only be transported with an assistant w
14. nz STG ASA 20 20 Version 8 0 01 2010
15. overed surfaces The best emergency call is however made with a cell phone 5 3 The lateral drive up flap In some cases stairwells it is not possible by reason of the place in front of the first step to drive onto the platform via both standard drive up flaps In this case an additional drive up flap must be mounted on the longitudinal side of the platform S 7 8 tem 5 5 4 Optical warning signal For every motor motion of the stair lift an optical signal is activated Orange blinking light on the cover This increases the protection in publicly accessible areas The signal repeats every second Operator manual Konstanz STG ASA 18 20 Version 8 0 01 2010 6 When malfunctions occur Malfunction possible cause measure Is the key on the operator panel Switch the key switch set to I and for the others correctly see 4 5 or 4 6 to 0 or removed Are all EMERGENCY OFF Unlock the EMERGENCY OFF switches switch by unlocked turning or pulling depending on design Set to I see 4 1 discharged personnel Safety catch is engaged Inform a technical specialist The lift does Are the safety gates Activate the safety gates one more not start up time when the in a horizontal position possibly move them platform is folded down slightly up or down and occupied Are the drive up flaps and the Press the drive up flaps and the safety Safety bar if present Bar lightly outwards freely mobile Drive in the oppo
16. r down Residual hazard falling from the platform Stop travel command immediately if obstacles or objects are found in or on the track or platform or travel area Residual hazard risk of crushing Do not remove signs belonging to the lift Have repairs performed exclusively by technical specialists Operator manual Konstanz STG ASA 9 20 Version 8 0 01 2010 A Do not allow body parts wheel chair parts or loads to protrude beyond the platform floor A Do not make any unnecessary motions on the platform such as teetering or swinging Residual hazard falling from the platform For inside and outside systems a short term or permanent flooding of the lift is prohibited Clean dirt on the lift with somewhat polish and a damp cloth not with water spray A Load carrying equipment and track must be sufficiently illuminated either with sunlight or electrically The electric lighting must be independent of timers At least 50 Lux at the entry and exit points or corresponding to the national employee protection directives Operator manual Konstanz STG ASA 10 20 Version 8 0 01 2010 4 1 4 2 4 3 4 4 The main switch The main switch red key is located within the platform behind the covering S 7 8 item 6 Counterclockwise rotation allows the key to be removed and thus the power supply interrupted Opening of the covering see 4 7 2 or 4 7 3 The main switch should be operated by technical personnel Total
17. r similar e Press the visible bolts forwards In the process the upper safety gates can be folded up at the same time manually e Now the operator can be helped out of the lift on the upper side The platform should be folded up manually so that the lift does not block the stair access See 4 5 2 In order to reach the main switch with the plastic version the cover screws must be removed then the cover can be pulled up Operator manual Konstanz STG ASA 17 20 Version 8 0 01 2010 5 Options Extras As required the platform lift Konstanz is equipped with the following extras 5 The folding seat All of our platform lifts can optionally be equipped with a folding seat S 7 6 tem 10 or retrofitted The folding seat is for those not in a wheelchair who would like to your the platform lift as a sitting area In the folded up condition the seat does not take up much space on the platform wall The folding seat is equipped with a safety belt which must be worn during travel if the user is not able to hold firmly to the gate or the hand grip 5 2 The emergency call All platform lifts must be equipped with an emergency call system Besides the standard there are other variations A Gong which is controlled by radio The sender who is supplied with a separate battery is located on the platform cover and directs the emergency signal to the gong wireless The range is between 40m for roofed surfaces and at least 10 m for unc
18. site direction Load carrying capacity exceeded Reduce the weight Only for Are all key switches set Switch the key switch Automatic to 0 except on the control correctly see 4 5 or 4 6 system station Lift does not selected by you fold down Are the batteries in the sender in Replace batteries in the sender order for radio operated automatically control stations If you cannot rectify the malfunction yourself please contact your customer service 7 Acoustical warning signal Duration Pause Reason Rectification 0 1 5 0 Battery undervoltage Drive to the charging station and Also see 4 2 charge the batteries Acoustical travel warning 2x short 4 0 Excess temperature of Continued travel after about 5min motor electronics cooling time is possible for or fuse defective insufficient cooling extend the cooling time by an additional 5 min Operator manual Konstanz STG ASA 19 20 Version 8 0 01 2010 3x short Defect in motor electronics us tone beeper in the platform Reduce weight or bring the center of Or overloading gravity closer to the direction of the rail Continuo E Emergency call by means of the Release emergency button Note The acoustical warning signal can be suppressed by pressing the emergency off button the loading procedure remains intact exception continuous tone 8 Services to your stair lift Konstanz at a glance Installed by Accepted by TUV on Operator manual Konsta
19. ton EMERGENCY OFF red button S 7 8 item 3 After inspecting or accessing the platform insert the key and turn to position 1 In the case of the automatic platform the safety gates close electrically 1f the pivoted lever or button is pressed and held in the travel direction The platform lift begins moving after the gates are closed In the case of a manual platform first close the safety gates manually horizontal position then press and hold the pivoted lever or button in the desired travel direction gt Upon reaching the target stopping point The platform lift stops automatically the respective position is set during assembly For the automatic platform hold down the pivoted lever or the button until the safety gates have opened For the manual platform release the pivoted lever or button and open the safety gates upward by hand Travel with the platform lift Special design 1 using the external control device with key switch with 3 settings S 7 8 item 2 for travel with opened platform via the external control device This option must be activated by a technical specialist within the control system It must be ensured that no third person can land spring in the travel route Condition Travel area is 100 visible The key switch S 7 8 item 2 should be set to position II otherwise as described in the standard design with the difference that here only the external control device is used Trave
Download Pdf Manuals
Related Search