USER`S MANUAL - X-Gloo
Contents
1. Creative Event Equipment USERS MANUAL _ WINDECKSTR 4 83250 MARQUARTSTEIN GERMANY a Tel 49 0 86 41 69 48 60 www x gloo com info x gloo com ia THANK YOU FOR YOUR TRUST GLO Skywalk GmbH amp Co KG congratulates you on the purchase of your X Gloo the modular lightweight tent system without compressors and poles In order to guarantee the perfect operation optimal function long product life and your personal safety and the safety of your guests please note the following Before you use your X Gloo for the first time read these operating instructions carefully and follow the safety indications If you loan your X Gloo Event Tent to another person please pass on these instructions and make sure that the person is fully advised regarding the technical aspects of the X Gloo Event Tent in order to avoid faulty operation All functions maintenance and repairs should only be carried out to the degree described in these operating instructions Please contact your X GLOO Team for repairs exceeding these instructions If you have any further questions we are always happy to assist you Service Hotline 49 0 8641 6948 60 Skywalk GmbH amp Co KG Windeckstrafe 4 83250 MARQUARTSTEIN GERMANY TABLE OF CONTENTS 4 5 6 8 1 Lay out the Matrix 8 2 Test the Valves cceeeeceeeeeee 8 3 Inflate ee eeeeeeeeeeeeees 8 9 Inflation with the H2. e If pressure loss still continues the quickest solution is to remove the Bladder and replace it as a damaged Bladder is likely the cause If the damage is visible on the Bladder and the damaged area is smaller than 1 cm gt Apply the Adhesive Repair Patch included in the Repair Kit If the damaged area cannot be found spray some soapy water onto the inflated Bladder surface so that the escaping air bubbles are visible and the damage can be located Then apply the Adhesive Repair Patch to repair the Bladder e Avoid pressure spots e g do not lean on the tent with your knees while folding the tent up e Store the X Gloo in a dry location and at temperatures not exceeding 40 celsius e Do not pack or store the X Gloo when damp or wet since this can cause the formation of mold spots and discoloration e At temperatures lower than 0 celsius folding can lead to damage of the components Take special care with the Window Walls in low temperatures and pack them carefully e Never store the X Gloo in an automobile in direct sunlight The intense heat can cause the Window Walls to stick together irreversibly or may cause permanent damage to the cloth A Important information for digitally printed parts Digital printed elements must be stored in dry condition CAUTION If the elements are stored while still damp the ink from the printed matenal can bleed and the printing can become permanently damaged We are unable t
3. 2 Step 3 Step 4 Step 5 Tel 49 0 86 41 69 48 60 www x gloo com info x gloo com Each Wall Ballast can be filled with water or sand gravel and then connected to the Wall using the provided toggle buttons 4 A PLEASE NOTE Inside of each ballast is a Water Bladder for use when filling the ballasts with water If you choose to fill the ballasts with sand or gravel you must first remove the Water Bladder from the ballast so it does not become damaged 1 If filling with water Included with each Wall Ballast are a hose and various faucet adapters Attach the hose to the faucet using the correct adapter 2 Open the velcro on the ballast cover and pull out the inner Water Bladder until the Fill Valve is visible Open the Fill Valve insert the other end of the hose and fill with water 3 Once full remove the hose from the Water Bladder and close the Fill Valve and the velcro on the ballast cover Using the four toggle buttons connect the Wall Ballast to the large grommets at the base of the Wall 4 When doing so be sure that the rubber coated side of the ballast is facing down Multiple Wall Ballasts are recommended for securing Walls on 5x5 6x6 and 8x8 model tents PLEASE NOTE The function of the Wall Ballasts is to reduce the risk of damage to the tent walls and zippers through exposure to high winds They are not intended to replace the Tube Ballasts Water Ballast Barrels or Anchoring Sets as
4. Bravo Turbo Max Connect the cable clamps to the respective connections of the battery red black and adjust the pressure control to 3 PSI Skywalk GmbH amp Co KG Windeckstrafe 4 83250 MARQUARTSTEIN GERMANY Step 4 Inflate two Tubes opposite one another 3 Step 1 Make sure that the pump hose is equipped with the correct adapter for the Valve Step 5 Inflate the third Tube so the tent will begin to rise Step 6 Using the Setup Support Bar to raise an 8x8 X Gloo the Tube intersection at the middle of the Roof and sets the fork of the Setup Support Bar directly under one of the Tubes in the area of the Tube intersection The second Step 2 Connect the hose to the pump and then connect the hose end with the adapter to the Valve on the X Gloo Tube Step 3 Now start the pump by turning the switch to ON Step 4 First inflate two Tubes opposite one another to form a 180 semicircle Step 5 Next inflate the Tube between those inflated in Step 4 The tent will begin to rise off of the ground Step 6 Now you can inflate the final Tube With the 8x8 it is recommended to work with two people One person lifts Step 2 Position two Tubes opposite one another in a half circle and then inflate with air 2 Inflate the remaining two Tubes as described in the regular setup process Follow these setup instructions if using our optional Protection Foil to help prevent soiling or damaging your X Gloo du
5. Connector and then remove the bolt and cap 5 The Tubes can then then be easily removed by sliding them out of the channels in the Tube Connector 6 For more information watch our how to video at gt GLOO Skywalk GmbH amp Co KG Windeckstrafe 4 83250 MARQUARTSTEIN GERMANY To reassemble the X Gloo Matrix simply reverse the disassembly process Starting near the Tube Connector attach each zipper on the roof to one of the four tubes 7 Next connect each toggle button on the roof to the corresponding loop on the tube ends 8 and then reconnect the velcro straps on the roof by first threading them through the buckles on the tube ends 9 For more information watch our how to video at Tel 49 0 86 41 69 48 60 www x gloo com info x gloo com TAKEDOWN CLEANING Make sure that all of the Tent Pegs are removed and all Anchoring Lines are released before deflating the Tubes on your X Gloo Step 1 Remove all elements e g Side Walls Canopy etc which are attached to the X Gloo Step 2 Next open the Overpressure Valve on each Tube 1 The air will completely escape within minutes Step 3 Then turn the X Gloo inside out so that the tube intersection loop is facing outwards 2 Step 4 Lay the Tubes on top of one another with the Valves facing upwards The Roof should be drawn outwards in large folds 3 Step 5 After the last of the air has escaped roll up the X Gloo
6. Covered area Hand Rumpor 15 min Covered area Hand Rumpa sa e sect cre 23 min without Side Walls 722 wie ECE Gy R 3 5 min without Side Walls Cc mioa Electric Pumpr eae 7 10 min with 4 Canopies ca 23m Operating pressure 0 2 bar 3 PSI with 4 Canopies ca 35 7 m Operating pressure 0 2 bar 3 PSI ca 42 kg ca 16 27 m2 car B0 Sme ca 51 34 m2 ca 1 82 Exterior side length ca 6m Tube diameter ca 37 cm Saree a teeereeeee ag ye m Weight without Walls ca 22 5 kg Exterior side length ca 7 85 m Weight without Walls ca 42 kg otal height ca 3 57 m Setup Entrance height ca 3 94 m Setup with Electric Pump 25 min Covered area TENG PAN leeer seer ener 30 min Total height ca 4 8 m without Side Walls 1627m aa Electric Ruins 10 15 min Operating i Covered area ca 30 3 m with 4 Canopies ca 51 34 m Operating pressure 0 35 bar 5 PSI pressure 0 18 bar 2 6 PSI Tube diameter ca 43 cm This data serves primarily as information since the operation of the Overpressure Valves is automatic gt _GLOO Skywalk GmbH amp Co KG WindeckstraBe 4 83250 MARQUARTSTEIN GERMANY STANDARD DELIVERY 4x4 5x5 AND 6x6 MODELS 1x X Gloo Multifunction Transport Bag 1 1x Hand Pump 2 1x Side Wall Bag 3 1x Anchoring Line Set 4 1x Manual and Quick User Gui
7. GLO ANCHORING Anchoring Lines Webbing inner Tube outer Tube O Walls The Anchoring Set consists of Anchoring Lines Anchoring Webbing for the 8x8 X Gloo Line Tensioner Tent Peg Puller for removing tent pegs stuck in hard or frozen ground 8x8 X Gloo only and assorted tent pegs packed in a Peg Bag 4 Anchoring Line Webbing Roof Zipper Rain Cover Wall 300 mm Long inner Tubes Anchoring Lines Walls 300 mm Long Walls inner Tube or Anchoring Lines 500 mm Long outer Tube inner Tube or Anchoring Lines rent peo Jovanmy Juss O OOOO Shoulder Loops 500 mm Long 14 mm Anchoring Webbing or Walls 500 mm Long 19 mm inner Tube Anchoring Webbing 800 mm Long outer Tube Using the Shoulder Loops Step 1 Push the loop end of one Anchoring Line Webbing through one of the Shoulder Loops on the tent 1 Step 2 Push the straight end of the Anchor Line through the loop end and pull it it through until the anchor line is tight around the Shoulder Loop of the tent 2 Step 3 Using a Line Tensioner secure the tent by connecting the Anchor Line to a tent peg positioned approximately 2 meters from the base of the Tube 3 Tighten the line using the Line Tensioner Step 4 Repeat on the other three Tubes gt GLOO Skywalk GmbH amp Co KG Windeckstra e 4 83250 MARQUARTSTEIN GERMANY Step 1 Step
8. a means to anchor the tent ELEMENTS The Side Walls are available in four variations as Standard Walls completely closed Window Walls Mesh Walls and Entrance Walls The zippers attach on the right and left of the Matrix and meet together at the top NOTE Side Walls can be installed with the side of your choice facing outward In this way it is possible to have the printed side of the wall facing the outside or inside of the tent 1 Attaching the Side Walls On the tube endings of the X Gloo you will find access to zippers to attach the Side Walls Connect the Side Wall to the X Gloo Matrix and close both zippers to the top of the wall 2 Closing the Side Walls with the Closing Rod For easier opening and closing of the Side Walls a Closing Rod is included in the delivery of the 5x5 6x6 and 8x8 X Gloo The hook at the end of the Closing Rod is connected to the Slider Puller and the Side Walls can be opened or closed 3 Standard Wall Window Wall Mesh Wall Entrance Wall gt GLOO Skywalk GmbH amp Co KG Windeckstrafe 4 83250 MARQUARTSTEIN GERMANY Opening and securing the Entrance Wall The Entrance Wall is zipped on as described above in Attaching the Side Walls To hold the Entrance Wall open open the zipper in the middle of the Wall and gather each side together On each side of the Entrance Wall you will find a toggle button on a length of cord Fasten each side by inserting
9. begins to compress When high wind force is expected gusts of more than 50 60 km h for the 4x4 5x5 or 6x6 and more than 40 km h for the 8x8 the tent must be secured and anchored A PLEASE NOTE If Side Walls are completely zipped in to a 6x6 tent a force of almost 500 kg is the result For this reason please pay special attention to the following points According to the ground surface you may require longer or additional stabilisation materials Additionally you must attach Anchoring Lines Webbing to all Shoulder Loops found on the outside of each Tube Our smaller Tube Ballasts ideal for use on hard ground Surfaces may not be sufficient for securing your tent against strong wind gusts Refer to our Wind Resistance Certificate to determine whether Water Ballast Barrels are required Winds stronger than 60 km h can lead to structural damage of the tent and this damage is no longer covered by the warranty If weather conditions deteriorate dramatically all Overpressure Valves should be opened immediately and the tent deflated Additionally the deflated tent should be weighted down In general the Protective Strips on the bottom of the Tubes are exposed to more wear and tear on rough surfaces due to the movement of the tent from wind Keep open fires and heat sources away from the X Gloo FIRE PROTECTION CLASSIFICATION e Description of Norms DIN 4102 B1 Abb B1 Controls testing and requirements on the
10. the toggle button through the loop of cord across from it 4 Folding over the Side Walls to make Half Walls 5 In order to secure the Side Wall in a horizontal half open folded position and prevent it from completely opening the zipper puller on each side of the wall should be fixed to the small velcro strips on the inside of the tent roof 6 amp 7 Preventing strain damage to the Side Wall zippers If the Side Walls are exposed to high pressure if the tent is set up in an area with high winds for example the zipper will bear the strain This is especially true for where the zippers are attached to the tube ends To relieve strain to the zippers and to avoid damage to the X Gloo or the Side Walls you will find straps and buckles lo cated at the base of each Side Wall Connect these to the webbing loops provided on the tube ends 8 Tighten each strap until the tension on the zipper is relieved 9 Tel 49 0 86 41 69 48 60 www x gloo com info x gloo com ELEMENTS The Tunnel Part makes it possible to connect one or more X Gloos It can be used to connect one size tent to a different size tent or to connect multiple tents of the same size The Tunnel Part is zipped on between the X Gloos instead of using a Side Wall 1 The Canopy can expanded the covered area of the X Gloo To attach it first prepare the two upper battens by connecting the two ends together 2 Insert the upper battens into the two sleeves
11. 10 Step 16 Push both valves through the corresponding holes in the Step 12 Gather the replacement Bladder in loose folds positioned above the opening in the upper Bladder Sack Img 11 Step 13 Now starting from the Bladder Sack at the opposite end thread the Tube completely onto your arm Grasp the end of the replacement Bladder through the upper Tube opening Img 12 Step 14 Pull the replacement Bladder carefully into the Tube Img 13 AX CAUTION Make sure that the replacement Bladder does not get twisted when pulling it in Try to enlist the help of a second person to help with the procedure Tel 49 0 86 41 69 48 60 www x gloo com info x gloo com For more information watch our how to video at Tube and press firmly to secure the velcro Make sure that no Tube material gets caught or pinched in the velcro Img 15 Step 17 Using the Fixing Element Tool included with in your repair kit or a loop of thin rope or cord pull each of the fixing elements through the corresponding holes in the Tube Img 16 RE PAI R A All functions maintenance and eventual repairs should only be carried out to the degree described in these operating instructions Please contact your X GLOO Team for repairs exceeding these instructions Step 18 To close the Tube ends fold over the corners of the Step 23 Make sure the entire Bladder Sack is back inside the Tube exposed Bladder so the outer most elongated holes in
12. 80L To give the barrel a cleaner appearance the remaining Space can be then filled with air using one of our Electric Pumps The hose provided with the Ballast Barrels is connected to the Pump in place of the Pump s yellow hose Step 3 Disconnect the hose from the barrel and make sure that both valves are tightly closed Step 4 With the help of an assistant carry the Ballast Barrel to your tent location by lifting it by the handles Or if you are on your own tip the barrel onto its edge and roll it Tel 49 0 86 41 69 48 60 www x gloo com info x gloo com Connecting to your X Gloo Ballast Barrels are connected to the X Gloo by use of an included shackel When connecting one or two Ballast Barrels to each Tube use the shackle to attach the eyelet at the base of each Ballast Barrel directly to the large gromet at the base of the Tube 2 When using three Ballast Barrels on each Tube the No Rub Mat should be used Connect the center eyelet on the No Rub Mat to the Tube grommet Then set the three barrels on the mat and connect each barrel to one of the three eyelets on the mat Digitally Printed Cover 3 The Ballast Barrels can be uniquely branded through the use of the Digitally Printed Cover Simply slip the cover over the barrel and close the zipper To Empty To empty the Ballast Barrel simply unscrew the lower valve cover and push open the check valve For more information watch our how to video at
13. and Pump 8 Inflation with the Electric Pump Bravo OV10 Bravo 2000 00 8 Inflation with the Bravo Turbo Max 12 V for car battery 8 Setup using the Protection Foil 9 10 Anchoring Tube Ballasts 10 Anchoring with Water Ballast Barrels 11 Anchoring with the Anchoring Set cccceeeeeneee 12 Securing Walls with Wall Ballasts 13 14 Side Walls sscsccctcecomssassadesncsdarulanetnswaces 14 Tunnel Part ccc cecceeseeeneeeeee 16 Canopy and Canopy Banner 16 Roof Banner ccc cccesceseeeeees 16 LED Lighting Kit 17 Removing the Roof 0006 18 Seperating the Tubes 0 18 Tel 49 0 86 41 69 48 60 www x gloo com info x gloo com Bladder Repair Replacement of the Protection Strip Bladder Replacement 20 20 21 21 21 22 25 TECHNICAL DATA w g e i ca 25 cm i N ca 13 3 kg x a C2 1 28 in Caselleseimnc 4M ca 23 m2 ca 35 7 m2 os Exterior side length ca 4m__ Tube diameter ca 25 cm Exterior side length ca 5m __ Tube diameter ca 31 cm Entrance height ca 2 0m Weight without Wallsca 13 3 kg Entrance height ca 2 5m Weight without Walls ca 18 8 kg Total height ca 2 3 m Total height ca 3 m Setup Setup
14. and Pump 1 min Diameter ca 42cm Operating pressure 0 2 bar 3 PSI Wedhi ccs cusssccccagtcrceve 2 5 kg Tel 49 0 86 41 69 48 60 www x gloo com info x gloo com
15. built into the Canopy 3 by first opening the Velcro found on one end of the sleeve Close the Velcro tab after each batten is installed After the upper battens are inserted attach the Canopy to the X Gloo making sure that the battens are facing downward Finally make sure the cover for the Overpressure Valve is firmly closed and then inflate the front tube While inflating lift the front tube to allow air to enter the full length of the tube A PLEASE NOTE The Overpressure Valve opens automatically as soon as maximal pressure is achieved The Canopy Banner 4 can now be attached if using using the zippers at the upper part of the Front Tube 5x5 and 6x6 models only The Roof Banner 5 also increases the covered area of the tent and it serves as a prominant branding surface To attach the Roof Banner simply connect it to the tent Matrix using the zippers Skywalk GmbH amp Co KG Windeckstra e 4 83250 MARQUARTSTEIN GERMANY LED LIGHTING KIT Hanging the LED Lighting Kit in your X Gloo Step 1 It is easiest to install the LED Lighting Kit during the setup of your X Gloo just after inflating three of the four tubes Take the long end of webbing connected to the LED light and loop it above the Tube intersection 6 Connect it to the buckle on the other side of the light Tighten the strap so the LED light is held snugly against the Tubes Step 2 Next extend the four toggles on the LED lighting mount and
16. cet using the correct adapter 3 Step 2 Open the velcro on the ballast cover and pull out the inner Water Bladder until the Fill Valve is visible 1 Step 3 Open the Fill Valve insert the other end of the hose and fill with water 4 Step 4 Once full remove the hose from the Water Bladder and close the Fill Valve and the velcro on the ballast cover Step 5 Connect the Tube Ballasts to the clips on the Tube endings 5 When doing so be sure that the rubber coated side of each ballast is facing down To secure your tent during stronger wind conditions multiple ballasts can be attached to each tube by connecting them to each other using the four toggle buttons on each ballast Ballasts can be connected side by side or on top of one another Step 6 Tighten the straps on the clips so that the ballasts prevent the tent from rising this provides the best stability gt GLOO Skywalk GmbH amp Co KG Windeckstrafe 4 83250 MARQUARTSTEIN GERMANY The Water Ballast Barrels can be used as anchors for your X Gloo as seating or as both Step 1 Open the two valve covers on the Ballast Barrel Make sure that the check valve at the bottom of the barrel is closed so that no water or air can escape when filling 1 Push open the check valve at the top of the barrel so that air can escape Step 2 Connect the included hose to the valve at the base of the barrel and fill with the desired amount of water up to
17. connect them to the loops on the inside of the X Gloo Tubes 7 Step 3 Tuck the cable underneath the roof so that it follows one Tube all the way to the ground 8 The fourth Tube can now be inflated Step 4 The transformer and dimmer controller can be safely stored on the ground Remove the LED Lighting Kit from your X Gloo using the steps above in reverse order Ensure that the LED light does not hit the ground when deflating your X Gloo For more information watch our how to video at www x gloo com en experience videos Tel 49 0 86 41 69 48 60 www x gloo com info x gloo com 17 ELEMENTS The X Gloo Matrix can be easily disassembled into individual parts Roof and Tubes Thanks to this feature the individual parts can be removed for repaired or replacement Re attaching the new or repaired part is just as easy Step 1 Beneath the Roof at each Tube end you will find two velcro straps fixing the tent Roof to the Tube Open both straps and disconnect them from the plastic buckles 1 Step 2 Remove the plastic toggle button from the loop which is located at the end of the zipper connecting the Roof to the Tube end 2 and then unzip the Roof from the Tube 3 Repeat Steps 1 and 2 on the remaining three Tubes The Roof can now be removed 4 Step 1 Remove the Roof as described above Step 2 Use an 8mm Allen key included in the Repair Kit to unscrew the bolt in the aluminum Tube
18. de 5 1x Closing Rod for X Gloo 5x5 6x6 6 1x X Gloo Repair Kit contents below 8x8 MODEL 1x Quick Pack Sack 7 1x Hand Pump 2 3x Side Wall Bag 3 1x Anchoring Webbing Set 8 1x Manual and Quick User Guide 5 1x Closing Rod 6 1x Setup Support Bar 9 1x X GLOO Repair Kit contents below 1x Replacement Protection Strip 11 1x Replacement Overpressure Valve 12 gt 1x Adhesive Repair Patches 13 1x Fixing Element Tool 14 1x Allen Wrench 15 a 1x Replacement Bladder 10 La 7 N Tel 49 0 86 41 69 48 60 www x gloo com info x gloo com SPECIAL INSTRUCTIONS e A transparent effect can occur especially with background light with different tent color combinations e g light Roof color and dark Tubes This should be taken into consideration by customers when designing the X Gloo If in doubt please consult your X GLOO professional Do not exceed the specified maximum air pressure The X Gloo is not intended for long term outdoor use and should be inspected for wear or damage after every event If small folds form inside the Tubes when inflating it is helpful with the larger tents to gently shake the Tube during the inflation process This will help keep the inner Bladder in the correct position assuring proper inflation The X Gloo should be deflated in winds exceeding 60 km h The first sign of overload is when the Roof
19. from the Roof to the Tube endings 4 Step 6 Now the X Gloo can be packed in the X GLOO Multifunction Transport Bag or Trolley Side Walls can be stored separately in the protective Side Wall Bag included in delivery For more information watch our how to video at Dirt and stains should be removed without the use of soap or A CAUTION Never use solvents detergent steam cleaning or water whenever possible We recommend using a soft dry brush or gasoline This destroys the cloth microfiber cloth If the stain cannot be brushed away then use a malk amaanco comaina soap with Wiser walk The X Gloo should be inspected visually and for functionality at least once a year by an expert This inspection includes inflating A Important information for digitally printed parts the X Gloo Tubes in order to check all pressure bearing parts for Digitally printed elements should NEVER be cleaned with soap tears punctures debonding heat or chemical damage and water Wetting these elements to clean them could result in the printing becoming permanently damaged In these cases X GLOO will not accept liability A All functions maintenance and eventual repairs should only be carried out to the degree described in these operating instructions Please contact your X GLOO Team for repairs exceeding these instructions gt GLOO Skywalk GmbH amp Co KG Windeckstrafe 4 83250 MARQUARTSTEIN GERMANY RE PAIR Z All functions mainte
20. nance and eventual repairs should only be carried out to the degree described in these operating instructions Please contact your X GLOO Team for repairs exceeding these instructions Our Adhesive Repair Patch 70 x 50 mm resists perforation is stretch durable and has been developed especially for repair of tears and holes in the Bladder e High adhesion guarantees impermeability e Resistant to UV exposure e Easy to trim e Resistant to moisture sand salt wind and high temperatures Step 1 Clean the dirt or oil from the area to be repaired using the Cleaning Cloth included 5 Step 2 Trim the Adhesive Repair Patch to the desired size and carefully remove the protective layer Try to avoid touching the sticky surface 6 Step 3 Press the Repair Patch onto the repair area and make sure that there is sufficient overlap of the repair area An overlap of at least 50 mm is recommended for larger tears or holes A PLEASE NOTE Press the Repair Patch uniformly and forcefully more pressure means that the tape will adhere more quickly Step 4 Allow the area to dry for several minutes 7 done Protection Strips are fitted with velcro to all four Tube endings of the X Gloo 8 as well as to the Tube endings of the optional Canopy To replace simply remove and attach the new one 9 Tel 49 0 86 41 69 48 60 www x gloo com info x gloo com RE PAI R A All functions maintenance and eventual repairs should o
21. nly be carried out to the degree described in these operating instructions Please contact your X GLOO Team for repairs exceeding these instructions Step 1 Lay out the tent neatly so that the damaged Tube is on Step 6 Unfold the Bladder Sack by pulling open a final velcro top and the service zipper is facing upwards strip Img 5 Step 2 Open the two velcro straps on the Tube end Img 1 Step 7 Pull the loose ends of the three velcro straps out of the Step 3 Open the service zipper on the Tube end Img 2 holes in the Bladder and Bladder Sack Img 6 Step 8 Open the Bladder Sack at the opposite Tube end using the Step 4 Pull the Bladder Sack out of the Tube Img 3 same method as d scribed inistens 2 6 Step 5 Open the 3 velcro straps which keep the Bladder Sack folded in half and pull them out of the plastic buckles Img 4 Step 9 Push pull both valves Img 7 and all of the small black fixing elements to the inside of the Tube Img 8 Both valves are secured inside the Tube with velcro Skywalk GmbH amp Co KG Windeckstra e 4 83250 MARQUARTSTEIN GERMANY Step 10 Pull the Bladder out of the Tube Img 9 Step 15 Feed the replacement Bladder completely through both Step 11 Lay the replacement Bladder parallel to the Tube valves should align with the corresponding holes in the Tube Tube ends making sure that the Bladder extends beyond the opening in each Bladder Sack Img 14 Img
22. o accept liability All kinds of repairs can be done in our workshop in Marquartstein or in the Service Center in Las Vegas Nevada We can also take care of special requests additional straps velcro strips etc at our facility e Maintenance and repair should be carried out only by X GLOO or by an authorized Service Center e The X Gloo should be periodically inspected for chafe marks and damage and promptly repaired e In order to avoid damage of the material coating first attempt to remove dirt and stains using a soft dry brush or microfiber cloth Only if necessary use a small amount of mild alkaline solution mixed with water Avoid the use of solvents washing machines or steam cleaning e Re waterproofing is not possible e Bleaching of the material is possible with extended UV exposure e g at high altitude or extended setup time White wall material tends to yellow from UV exposure and is easily stained when contacted with dust and dirt All of the materials currently implemented in the X Gloo have been subjected to extensive material testing It is practically impossible to state when exactly a color change could become visible since the influencing factors vary strongly However All cloths change in color with extensive UV exposure According to expert knowledge with proper care the X Gloo will show only minimal color change after many years of use The range of use will not be limited The materials used and the
23. reaction to fire of building materials German norm used in most European countries CPAI 84 95 Section 6 Specification of the American Association of Sailcloth Materials for the assessment of flame retardant materials used in event tents Due to the fact that the the X Gloo is in use worldwide at tradeshows as an innovative event tent we reserve the right not to certify the tent according to the national norms of each country The certification according to CPAI 84 fulfills the international requirements for flame resistance in tent products and includes similar test criteria like DIN 4102 B1 or NFP 92501 7M2 e When the tent is used in sandy terrain avoid getting sand grains in the Tubes or in the Pump e Keep the valves free of sand and dirt particles and clean them if necessary since this can cause faulty operation and pressure loss e The tent can be damaged by the penetration of sharp objects e g knives tools in the Tubes causing leakage and loss of pressure Handle the X Gloo with appropriate care e Avoid extreme variations in temperature day and night or long term use This can lead to loss of air pressure requiring reinflation of the tent gt GLOO Skywalk GmbH amp Co KG Windeckstrafe 4 83250 MARQUARTSTEIN GERMANY Procedure in the case of pressure loss e FIRST close all valves TIGHTLY e If pressure loss continues blow out the Overpressure Valves to remove all dust or dirt particles
24. refore the entire tent are waterproof Tel 49 0 86 41 69 48 60 www x gloo com info x gloo com 1 Spread the X Gloo Matrix out in the area intended for setup Try to make sure that the tube endings of the X Gloo are positioned approximately where you want them once the tent is inflated This way you can avoid having to reposition or handle the tent again 8x8 ONLY Zip in the Middle Wall Since the entrance height of an assembled X Gloo 8x8 is very high we recommend zipping in the Middle Wall before inflating the tent A PLEASE NOTE Only the outer side of the Middle Walls are equipped with a Zipper Rain Protector If you should choose to attach the Middle Wall with the outer side facing inwards so that a logo printed on the outside is be visible from the inside of the tent for example the waterproof quality of the tent in the area of the zipper can not be guaranteed 2 The Valve consists of the socket ring 1 attached to the Bladder and a screw on housing 2 with attached protective cap 3 The housing must be tightened securely to the socket ring before inflation 4 The Backstroke Valve in the housing prevents air from escaping In order to prevent dirt from entering the protective cap is screwed onto the housing after inflation is complete To deflate simply unscrew the housing from the socket ring AX PLEASE NOTE There is one red Overpressure Valve 5 on each Tube located beside the Valve The Ove
25. ring setup Step 1 Lay out the Protection Foil where you want to set up the tent and roll the Matrix out on top of it 1 Step 3 Position the Tube ends at the edges of the Foil so that grommets on the Tel 49 0 86 41 69 48 60 www x gloo com info x gloo com For more information watch our how to video at Step 4 person operates the pump moving it as necessary with the Tubes as they are inflated Step 7 Close the Valves after inflating the Tubes Step 8 If the Tubes have been inflated correctly the X Gloo will stand in a stable and wrinkle free position All four Tubes can now moved by hand to the final position ie inside of the Tube ends rest exactly over the grommets of the Protection Foil 3 Remove the Protection Foil and anchor the tent using one or more of the methods described on pages 10 13 ANCHORING Each Tube Ballast Set includes four ballasts The ballasts can be filled with water or sand gravel and then connected to the inside or the outside of the tent Tubes by using the two clips on each ballast AX PLEASE NOTE Inside of each ballast is a Water Bladder 1 for use when filling the ballasts with water If you choose to fill the ballasts with sand or gravel 2 you must first remove the Water Bladder from the ballast so it does not become damaged If filling with water Step 1 Included in the Tube Ballast Set are a hose and various faucet adapters Attach the hose to the fau
26. rpressure Valve opens automatically as soon as the Tubes reach the maximal pressure The function of each Overpressure Valve should be tested before inflation To do this unscrew the housing and make sure that the spring can be pushed in A PLEASE NOTE Sand and dirt can clog the spring and Overpressure Valve so that the function is negatively influenced Inflation with the Hand Pump The Hand Pump included in the standard delivery is equipped with different valve sockets and an air hose Do not kink or press down on the air hose to avoid air leakage or damage A PLEASE NOTE See the notation on the hose connection Inflate Deflate GLO Inflation with the Electric Pump Bravo 0V10 and Bravo 2000 Screw the hose included in delivery to the correct opening on the pump Ad PLEASE NOTE See the notation on the hose connection IN Inflate OUT Deflate Stick the plug into the outlet Please note that the Bravo 2000 has a booster which can be turned on with the switch Please read and folllow the operating instructions included with the Bravo OV10 and Bravo 2000 120V and 230V models available Inflation with the Bravo Turbo Max for 12V automobile battery The Bravo Turbo Max can be connected to a 12V automobile battery To avoid draining your battery make sure that it is fully charged or that the vehicle is running while operating the pump Please read and follow the operating instructions included with the
27. the and close the service zipper Img 26 Bladder line up on top of those just beside them The result should look like a row of three visible holes instead of five Img 17 Step 24 Close the Bladder Sack on the remaining Tube end using the same method Step 19 Thread the 3 long velcro straps through the corresponding holes in the Bladder and Bladder Sack Img 18 amp 19 Step 20 Fold the Bladder Sack in half pressing it firmly to close the long velcro strap in the middle Img 20 amp 21 Step 21 Loop the three velcro straps through the corresponding For more information watch our how to video at plastic buckles on the Bladder Sack and then press each one firmly to close it Img 22 amp 23 Step 22 Push the Bladder Sack back into the Tube and then thread the two velcro straps for connecting the Bladder Sack to the Tube end out through the provided holes Close them by pressing firmly Img 24 amp 25 X RELAX The core of the X Relax is a cylindrical Bladder similar to the Bladder construction of the X Gloo event tent To inflate Step 1 Remove the X Relax from the included bag Step 2 Locate and open the valve cover 1 to expose the valve 2 Step 3 Inflate using a Hand Pump done The X Relax design enables an inexpensive replacement of the outer Shell and therefore the option to change the design of the X Relax while retaining the existing Bladder Height ca 60cm Setup with H
Download Pdf Manuals
Related Search