User manual EN
Contents
1. If in the menu display settings display TC is set the continuous viewing of time code there will be displayed user bits while SET button is hold On the other hand if in the menu display settings display TC is set the continuous viewing of user bits there will be displayed time code while SET button is hold Fi This feature facilitates to display the user bits or time code without having to change the settings in the menu see chapter 8 5 Display TC Copyright BETSO ELECTRONICS Ltd User manual BETSO WTCS 9 3 Change of display brightness The slate allows you to adapt the brightness of the display to the actual light conditions There are ten levels of display brightness available The last setting Is automatically saved il Feature full brightness allows you to use lower brightness than would be ij necessary for a proper camera record under the actual light conditions See chapter 8 8 Full brightness 9 4 SMPTE TC signal frame rate information This feature displays the frame rate of the receiving SMPTE TC signal on the display of the slate In the case that it is used non integer frame rate 23 98 29 997 etc it will be displayed a rounded value 24 30 etc In the case of drop frame format there will be displayed dF characters after the frame rate information or ndF characters in the case of non drop frame format 9 5 Battery level display Displays a bar graph of battery level If the batteri2. User manual BETSO WTCS WTC S BETSO 16 channel wireless digital TC slate rs MOS SYNC EXT INT DAY NIGHT pare HBB l 1HB l PROD TITLE 8 sou SCENE TAKE J Copyright BETSO ELECTRONICS Ltd User manual BETSO WTCS Contents 1 Product GeSCriptlonissidceeccenchahieendcrexs nie nn nerve anses ane no a een vens 3 2 TON TE AUN es saone cns aides ones tion nee intet a nne ad uene 3 2 Control GIS VIN CS sense anis net ee dan ee che benne evene 4 4 Insertion of batteries accumulators ses 6 5 External power SPP nan a tn die nano n ee 6 Oy TUNING Oferon a E aa dde designers dau EEE E 7 Te Control of the Men nerea raa a a e aa e aaan E EE aaia DE 7 8 Settings of the SA Eisen eat one ne 7 8 1 Battery type setting of the type of the batteries 8 8 2 TC source setting of the source of TC Signal dineanenentenanerun 8 8 3 RF channel setting of RF channel for TC signal reception 8 8 4 RF type setting of RF mode used for TC signal transmission 9 8 5 display TC setting of displayed data during opened arm of the slate 9 8 6 TC hold setting of duration of displaying of TC after a clap 10 8 7 UB hold setting of duration of di
3. e advanced monitoring of batteries level with signalization of discharged batteries 3 Control elements Arm of the slate Button UP Button SET Button DOWN Power on indication LED Button ON OFF for power on of the slate Ooo PB ND Ha 7 Connector for connection of the external back light for writing sheet 8 Door of battery compartment 9 Antenna Copyright BETSO ELECTRONICS Ltd User manual BETSO WTCS ees MOS SYNC EXT INT DAY NIGHT pare RAREBRBARAaAL IS 1 0 ooo pie cam nou scene Taxe J o Q G o Sync high brightness LED for indication of clap or 00 frame Display Indication of displaying user bits of incoming TC signal Replaceable slate writing sheet Antenna RP SMA connector Fe ee DE Input connector jack Neutrik 6 3 mm for connection of cable with TC input Signal or external power supply Copyright BETSO ELECTRONICS Ltd User manual BETSO WTCS 4 Insertion of batteries accumulators To power TC slate insert 6 ce
4. to protect the device against direct contact with water es To clean the device use a dampened piece of cloth Never use any chemical solvents bee Copyright BETSO ELECTRONICS Ltd User manual BETSO WTCS 12 Technical specifications Dimensions w x h x d 270 x 207 x 30 mm with large writing sheet 225 x 150 x 30 mm with large writing sheet Weight approx 1130 g including battery Mechanic construction anodized aluminium alloy wood and ball bearings SMPTE TC signal 23 976 fps 30 fps including up to 2x speeded up Input sensitivity 0 2 10 V p p Powering 6x AA alkalic battery accumulator external powering 6 18 V via 6 3mm Jack connector RF output power 10mW 10dBm Number of channels 16 0 F Frequency range 433 15 434 65 MHz Channel bandwidth 100 kHz Frequency deviation 20 kHz Current consumption approx 0 3 8 W 30 900 mA approx 0 02 W 2 5 mA in stand by mode arms of the slate closed Battery life up to 64 hours with the lowest display brightness 13 Schematics of connectors Input connector Connector of LED backlight 1 GND 1 Unconnected 2 External power supply 6 18V DC 2 GND 3 SMPTE TC signal 3 5V DC Copyright BETSO ELECTRONICS Ltd User manual BETSO WTCS 14 EC Declaration of conformity BETSO ELECTRONICS s r o Elisky Premyslovny 1335 156 00 Praha 5 Zbraslav Reg number 28955706 declares that this device BETSO WTCS specification D
5. channel for TC signal reception menu RF channel With this feature you can set the RF channel on which the TC signal will be received Copyright BETSO ELECTRONICS Ltd User manual BETSO WTCS channel set 0 F setting of one of sixteen channels for SMPTE TC signal reception 0 1 9 A B C D E F You must set the same channel which is set on RF transceiver BETSO TCX il This feature allows that up to 16 independent systems slate transceiver or transceiver transceiver can be used on one place 8 4 RF type setting of RF mode used for TC signal transmission menu RF type With this feature you can choose the type of RF data transmission mode which is currently used by the transceiver Supports reception of TC signal in packet format of BETSO PACKET standard that was developed to significantly reduce the transmission failure by other RF systems or in the second case you can choose a standard mode of TC transmission which on the other hand allows the co operation with the system BETSO TCXS robust packet mode of TC transmission normal standard mode of TC transmission Default and recommended setting in the case that you don t need to use the ij slate with BETSO TCXS is robust 8 5 display TC setting of displayed data during opened arm of the slate menu display settings display TC This feature allows you to specify which data will be displayed on the display of the slate a
6. es are just before discharge and the last segment of the bar graph is already flashing immediately replace the batteries with the new ones Ci ot JL APP 1 Battery voltage in volts 2 The lower level segment indicates discharged batteries 3 The higher level segment indicates fully charged new batteries Copyright BETSO ELECTRONICS Ltd User manual BETSO WTCS 10 Recommended accessories Optional accessories include a compact front slate information area FD 1 or FD 2 receiver for the script BETSO WSR and various cables for the connection of the SMPTE TC signal and the external power supply For the latest information about our products BETSO please contact your local distributor or visit our website http www betso eu 11 Troubleshooting It is impossible to turn on the slate If you use an external power supply check if there are no batteries inserted and that the inversion of the polarity of the external power supply didn t occurre Otherwise make sure that there are inserted charged batteries or whether they are not inserted with the reversed polarity The slate doesn t receive SMPTE TC signal If it is used the wireless transmission Make sure that it is used the same RF channel as the transmitter is using see chapter 8 3 Than the function RF type see chapter 8 4 has to be set on the same mode of transmission as the transmitter is using Finally make sure that function TC source
7. f backlight of the slate information area menu board LED Feature Board LED activates the output which is ready for connection of e g LED backlight of the slate information area On Off this feature can be enabled and disabled Copyright BETSO ELECTRONICS Ltd User manual BETSO WTCS Schematic of connector for connecting of e g LED backlight of the slate information area is provided in the technical specifications at the end of this manual 8 12 Auto OFF setting of automatic turn off delay menu auto OFF This feature allows you to enable the automatic turn off of the slate if the slate is not used for a prolonged time Delay before the automatic turn off can be set to 1 2 or 3 hours Disabled automatic turn off feature is disabled 1 3h automatic turn off feature is enabled with delay of 1 2 or 3 hours Delay of the automatic turn off feature is measured from the time of the last pressed key or from the time of the last clap of the slate 8 13 script setting of RF channel for co operation with BETSO WSR product menu script This feature allows co operation with scripting device BETSO WSR To activate this feature you need to set the RF channel on which you wish to run this function If this channel is set and this feature is enabled then after each clap of the slate there will be transmitted the concrete SMPTE TC signal containing the time code and user bits of the frame in which the clap occurred by
8. fter the opening of the arm of the slate There is the possibility to display the sync time of TC or in the second case the user bits time code after the opening of the arm of the slate it will be continuously displayed incoming sync time of TC signal user bits after the opening of the arm of the slate it will be continuously displayed information stored on user bits positions within the incoming TC signal Copyright BETSO ELECTRONICS Ltd User manual BETSO WTCS 8 6 TC hold setting of duration of displaying of TC after a clap menu display settings TC hold This feature allows you to set the time during which there will be displayed time code on the display of the slate after the clap We can set the time of displaying in the number of frames on which we want to have a time code recorded 0 250 frames setting of duration of displaying of TC after the clap in frames After a clap it is always displayed first during TC hold time code and then ij during UB hold user bits of the frame in which the clap occurred 8 7 UB hold setting of duration of displaying of user bits after a clap menu display settings UB hold This feature allows you to set the time during which there will be displayed user bits on the display of the slate after the clap We can set the time of displaying in the number of frames on which we want to have user bits recorded 0 250 frames setting of duration of displaying of user bit
9. hat has important instruction character If you overlook this T information it may result in product damage Copyright BETSO ELECTRONICS Ltd User manual BETSO WTCS Thank you for purchasing BETSO product Please pay sufficient attention to the following user manual of your new product BETSO Following these instructions you will avoid the possible damages of your new device and at the same time they will be presented to you all the available features that allow you to take advantage of the potential of the product For the latest information about our products BETSO please contact your local distributor or visit our website http www betso eu 1 Product description The function of our wireless slate BETSO WTCS is to receive and display the time code TC Time Code signal of any frame rates including up to double speed up TC signal Supports reception of TC signal in BETSO PACKET standard that was developed to significantly reduce the transmission failure in the noisy RF radio environment Of course it s also possible to connect TC signal to the wireless slate BETSO WTCS through cable The settings of all special functions of our wireless slate BETSO WTCS is done via an intuitive menu The slate can be batteries powered as well as an external power source can be used 2 Top features e precise mechanic construction from anodized aluminium alloy and stiff wood e ball bearing utilized for gentle operation and long lifet
10. igital wireless time code slate frequency range 433 15 434 65 MHz radiated power 10 mW 10 dBm max duty cycle lt 10 RF channels 16 channel bandwidth 100kHz conform to the essential requirements of the R amp T TE Directive 1999 5 EC To demonstrate compliance with these requirements the following standards were consulted EN 300 220 Radio spectrum Matters ERM EN 301 489 Electromagnetic Compatibility EN 60065 2002 Safety of Electrical Equipment Conformity assessed via Annex III using a Technical Construction and Results of measurements August 2010 Ing Jan Zastera general manager E mail zastera betso eu Copyright BETSO ELECTRONICS Ltd
11. ime of the arm of the slate e easy recall the sync time of a last clap e optional displaying of synchronization time user bits e intelligent functions full brightness and led flash e 10 levels of display brightness e possibility of external back light of the slate information area e intuitive control with quick menu based setting of all advanced functions e auto off function e 16 RF channels in the band 433 15 434 65 MHz e possibility of reserve random RF channel for co operation with TC receiver for script BETSO WSR e packet mode of RF transmission according to BETSO PACKET standard minimizing the transmission failure in the interfering radio environment Copyright BETSO ELECTRONICS Ltd User manual BETSO WTCS e basic mode of RF transmission that allows reception of TC signal by other transceiver BETOS TCX e automatic choice between RF cable input of TC signal e wireless range of up to 450 m in packet and up to 350 m in standard mode in the conditions of direct visibility e supports 23 976 fps 30 fps drop frame and non drop frame SMPTE TC formats includes up to two times speeded up TC for use in video clips etc e low consumption allowing operating time up to 600 hours in standby closed arm of the slate and up to 60 hours in active mode operating time in active mode depends on the level of display brightness of the slate e variable power supply 6x AA batteries accu or external 6 18V DC power supply
12. is set to one of the options Auto or Radio see chapter 8 2 if the option Auto is selected make sure that the cable is not connected to the slate If it is used the transmission via cable Make sure that function TC source is set to one of the options Auto or Cable see chapter 8 2 and that the cable is connected to the slate The slate in the wireless mode receives a very noisy TC signal If you are not trying to use the slate away from the work range of the transmitter try to use an another RF channel see chapter 8 3 RF channel Than you can choose in the setting of function RF type see chapter 8 4 the option Robust make the same change of RF mode setting on your transmitter Copyright BETSO ELECTRONICS Ltd User manual BETSO WTCS The automatic choice between RF cable input doesn t work Use the manual setting of function TC source to Cable for reception via cable or to Radio for the wireless reception of the SMPTE TC signal see chapter 8 2 Safety instruction Never insert the batteries if you use the external power supply it can damage the Slate Never open an electrical device All reparations must be performed by an authorized service center In the case of opening of the device away from the authorized service center you will automatically loose the warranty of the device Do not use the electrical device in the places with high humidity especially take care
13. ll of alkaline batteries or accumulators of size AA UM3 to the attached battery pack After checking of the polarity of the inserted batteries accumulators insert the battery pack into the slate in the indicated way Lil The slate is protected against destruction by inserting battery pack with wrong polarity Warning Never insert the batteries if you use the external power supply It may result in the damage of the slate and rapid battery discharge 5 External power supply External power supply 6 18V DC is possible to connect using a special cable connected to the input jack connector which connection is shown below 1 GND 2 6 18V DC 3 TC SIGNAL p Warning Never insert the batteries if you use the external power supply It may result in the damage of the slate and rapid battery discharge Copyright BETSO ELECTRONICS Ltd User manual BETSO WTCS 6 Turning on Turning on ON long press ON OFF button Turning off OFF long press ON OFF button il After the turning the slate on it will show a welcome text BETSO After that the slate is immediately ready for use according to last saved settings 7 Control of the menu Start menu long press SET button during the off state of the slate End menu long press SET button in the main menu by opening of the arm of the slate Move up press UP button Move down press DOWN button Enter sub menu short press SET button Leave sub menu long press SET button E
14. nter setting short press SET button Change of parameter press UP DOWN buttons Save changes short press SET button You can rapidly leave the menu by opening of the arm of the slate 8 Settings of the slate Control of the menu is described in the previous chapter 7 Control of the menu Copyright BETSO ELECTRONICS Ltd User manual BETSO WTCS 8 1 Battery type setting of the type of the batteries menu battery type With this feature you can give the information about the type of the batteries used in the slate accu 1 2V 1 2V accumulators are used in the slate battery 1 5V 1 5V batteries are used in the slate Lil Setting of the type of the batteries affects some functions of the slate Low batteries indicator we recommend to actualize this setting when you change the type of the batteries 8 2 TC source setting of the source of TC signal menu TC source With this feature you can set whether you want to use wireless cable or automatic selection of input for the synchronization SMPTE TC signal By the automatic input selection it is preferred the cable one In other words if you connect the cable to the slate the RF input will be ignored even if the cable doesn t contain a valid SMPTE TC signal auto automatic selection between RF cable input cable preferred cable cable input selected radio radio input selected i Default and recommended setting is auto 8 3 RF channel setting of RF
15. s after the clap in frames After a clap it is always displayed first during TC hold time code and then ij during UB hold user bits of the frame in which the clap occurred 8 8 Full brightness feature of full brightness after a clap menu special functions full brightness Feature full brightness will increase the brightness of the display after the clap to maximum value during displaying time code and user bits TC hold UB hold Copyright BETSO ELECTRONICS Ltd User manual BETSO WTCS On Off this feature can be enabled and disabled Allows you to save the energy of the batteries by the setting the display brightness to a lower value than would be necessary for a proper camera record under the actual light conditions Thanks to this feature the data displayed by the slate after a clap will be always very well readable on the record made by camera under any light conditions 8 9 00 frame feature of flashing of sync LED in zero frames menu special functions LED flash 00 frame Function 00 frame will turn on the sync LED during each zero frame of each new second On Off this feature can be enabled and disabled 8 10 Clap feature of flashing of sync LED during a clap menu special functions LED flash clap Function clap will turn on the sync LED during the frame in which the clap will occur On Off this feature can be enabled and disabled 8 11 Board LED feature o
16. splaying of user bits after a clap 10 8 8 Full brightness feature of full brightness after a clap 10 8 9 00 frame feature of flashing of sync LED in zero frames 11 8 10 Clap feature of flashing of sync LED during a clap 11 8 11 Board LED feature of backlight of the slate information area 11 8 12 Auto OFF setting of automatic turn off delay s s s dune oasis 12 8 13 script setting of RF channel for co operation with BETSO WSR product 12 9 Control of the opened slate sisi 13 OU NG ea a dde cad sseameonetens 13 9 2 Switching between user bits time code 13 9 3 Change of display brightness 14 9 4 SMPTE TC Signal frame rate INTOMAUON 28848 ressens oett enipient 14 9 5 Battery level dla Aie anse rene nee tune 14 10 Recommended ACC SSOrIeS can enen rans acdnobaranmutnetinbaicddas Graniisandmanamanenetamiaonstiin 15 11 Troubleshooting s issus escusnsiiisnnanneniennnnnteesunrnd niennun ren nnussuut 15 12 Technical SD CIIOAMONMS ESS ne aan cn den een one tete tance 17 13 Schematics OF CONNE CTOPS none content ediento nb benonsaleeete 17 14 EC Declaration of COMONMIO Seed ren ae rene nne aaeesenes 18 Used symbols Lil Indicates text that has only informative character If you overlook this information it can t result in product damage by it s mishandling i Indicates text t
17. the slate This data will be transmitted in the packet mode of the BETSO PACKET standard transfer OFF script feature is disabled channel set 0 F after the setting of one of 16 channels 0 1 9 A B C D E F the script feature will be activated Copyright BETSO ELECTRONICS Ltd User manual BETSO WTCS 9 Control of the opened slate clap the clap of the arm of the slate displaying of user bits time code long press and subsequent hold of SET button change of display brightness press UP DOWN button show TC frame rate short press SET button battery power indication short press ON OFF button 9 1 Clap After the clap of the arm of the slate it will be stopped the displaying of currently running TC and on the display of the slate there will be temporally displayed time code during the TC hold time and after that user bits during the UB hold time Both informations displayed are those which have been received in the frame in which the clap occurred After these informations there can be displayed the low batteries power indication on the display If this warning accurs change the batteries immediately Whenever after the clap you can recall the time code and user bits of the frame in which the last clap occurred by short press SET button To switch between time code and the user bits of the frame in which the last clap occurred press UP DOWN button 9 2 Switching between user bits time code
Download Pdf Manuals
Related Search