MIC-3021/8 6U/7U CompactPCI ® Industrial Computer
Contents
1. 2 3 4 Replacing the Fan Tray and Air Filter 22 Preface and Table of Contents Figure 1 1 Figure 2 1 Figure 2 2 Figure 2 3 Figure 2 4 Figure 2 5 Figure 2 6 Figures MIC 3021 8 dimensions seseeeenee 11 Front view of MIC 3021 8 res 15 Rear view of MIC 3021 8 rennes 16 Installing a card into the chassis c sccscsseees 18 Install a device on the top tray eesssvvessvvensvevssveeeee 20 Attaching the mounting brackets to a 5 25 device cicca 21 Attaching mounting brackets to a half height device for mounting in device space next to the fan tray mod le jeierenseseserenserensesrdrsenensesenasanevrespesennnaessnnenes 22 MIC 3021 8 User s Manual CHAPTER 1 General Information 1 1 Introduction The MIC 3021 8 is an 8 slot 6U 7U sized CompactPCI enclosure for rack or panel mounting It has eight 6U card slots and has a device bay which can accommodate devices and peripherals such as floppy disk drives and hard disk drives Its rugged construction and flexible modular design allows users to configure it to meet the requirements of individual applications The MIC 3021 8 comes in two versions 6U high without a fan tray or 7U high with a fan tray The 1U high fan module provides forced air cooling in the system Two 88 CFM high speed fans are mounted in a hot swappable tray directly underneath the card slots The fan s tachometer output enables the alarm module to monitor the speed of2. CHAPTER 2 1 Initial inspection We have carefully inspected the MIC 3021 8 mechanically and electrically before shipping It should be free of marks and scratches and in perfect working order upon receipt As you unpack the MIC 3021 8 check it for signs of shipping damage damaged box scratches dents etc If it is damaged or if it fails to meet specifications notify our service department or your local representative immediately Also notify the carrier Retain the shipping carton and packing material for inspection by the carrier After inspec tion we will make arrangements to repair or replace the unit Warning We strongly recommend that only qualified experi enced personnel install or remove components and that they practice extreme caution when doing so 14 MIC 3021 8 User s Manual 2 2 The MIC 3021 8 Chassis The MIC 3021 8 is designed to be installed and maitained easily The following illustrations show the components on the front and rear side of the enclosure Optional system alarm System slot and monitor module Power on off rennais miami switch Device protection Fan tray door Device trays Figure 2 1 Front view of MIC 3021 8 Chapter 2 Installation 15 16 Optional system alarm and monitor module 1 0 Power supply switch Figure 2 2 Rear view of MIC 3021 8 MIC 3021 8 User s Manual 2 3 Installation Procedures 2 3 1 Card Installation and Rem
3. MIC 3021 8 6U 7U CompactPCI Industrial Computer for Rackmounting Copyright Notice This document is copyrighted 1999 All rights are reserved The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice No part of this manual may be reproduced copied translated or transmitted in any form or by any means without the prior written permission of the original manufacturer Information provided in this manual is intended to be accurate and reliable However the original manufacturer assumes no responsibility for its use nor for any infringements upon the rights of third parties which may result from its use Acknowledgements PICMG CompactPCI and the PICMG CompactPCI logos are trademarks of the PCI Industrial Computers Manufacturers Group All other product names or trademarks are properties of their respective owners Part No 2003302100 Ist Edition Printed in Taiwan April 1999 MIC 3021 8 User s Manual Product warranty Advantech warrants to you the original purchaser that each of its products will be free from defects in materials and workmanship for one year from the date of purchase This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech or which have been subject to misuse abuse accident or improper installation Advantech assumes no liabil
4. ace 48 TE incl 7 CompactPCI slots and one system slot Hot swappable platform complies with PICMG 2 1 R 1 0 Hot Swap Specification Dimensions W x H x D mounting flanges not included 7U 440 x 311 x 254mm 17 3 x 12 25 x 10 6U 440 x 267 x 254 mm 17 3 x 10 5 x 10 Weight 12 kg Operating temperature 0 50 C 32 122 F Storage temperature 20 C 70 C 4 158 F Relative humidity 10 95 40 C non condensing Operating altitude 0 to 10 000 feet 3048 meters Chapter 1 General Information Storage transit altitude 0 to 40 000 feet 12 190 meters Shock 10 G operating 30 G storage transit e Random vibration 1 Grms operating 1 3 2 Fan Tray Module Air flow Two 88 CFM fans providing 176 CFM in total e Power Consumption 0 37 A 12 V per fan 0 74 A total e Rated fan speed 2200 rpm Life expectancy 50 000 hours 25 C 1 3 3 ATX Power Supply e Input 90 135 or 180 265 V lt 47 63 Hz switchable e Output 3 3 V 15 A 5 V 26 A 12 V 9 A 12 V 0 8 A e Minumum load 3 3 V 0 3 A 5V 2A 12V 1A e Max output 250 W total 170 W for 5 V and 3 3 V e MTBF 50 000 hours 70 load Safety UL CUL CE 10 MIC 3021 8 User s Manual 1 4 Dimensions Figure 1 1 MIC 3021 8 dimensions Chapter 1 General Information 11 12 MIC 3021 8 User s Manual Installation
5. er Preface and Table of Contents Packing List Before installing your board ensure that the following materials have been received 1 MIC 3021 8 Compact PCI enclosure with backplane e 1 box of accessories warranty certificate This user s manual If any of these items are missing or damaged contact your distributor or sales representative immediately Technical Support and Sales Assistance If you have any technical questions about the MIC 3021 8 or any other Advantech products please visit our support website at http support advantech com tw For more information about Advantech s products and sales informa tion please visit http www advantech com MIC 3021 8 User s Manual Contents Chapter 1 General Information ernnnnnnnnneren 7 1 1 Introduction seseneevoennnenneenneennvennresnneennvennnennnennnenenennneennee 8 1 2 Features eennesnrennrennrennrennnenneenvennrennnennsennnennnenneennnenenennseenee 9 1 3 Specifications svccccccccccssessesconsvebesscssasenascooessoutsevenasdeecserasess 9 1 4 Dimensions seoerervvenveennnennvennvennrennsennnennnenneennnennnennnennnennsee 11 Chapter 2 Installation cccceeceeeeeeeeeeeees 13 2 1 Initial inspection 14 2 2 The MIC 3021 8 Chassis rennes 15 2 3 Installation Procedures ses 17 2 3 1 Card Installation and Removal sesesssvvvevsvevesesee 17 2 3 2 Before Operating the System se 19 2 3 3 Installing Peripherals ss 20
6. he back cover of the chassis and connect cables to the installed device and to the backplane 6 Reattach the back cover One device space is available next to the fan tray module in the 7U high version of the MIC 3021 8 which can be used for installing a 5 25 device One pair of mounting brackets without guiding flange are included for mounting the device Since the brackets are not guided we recommend that users install only a half height device such as a CD ROM or a removable drive mount Chapter 2 Installation 21 22 Figure 2 6 Attaching mounting brackets to a half height device for mounting in device space next to the fan tray module 2 3 4 Replacing the Fan Tray and Air Filter The fan tray module of MIC 3021 8 is designed to be hot swappable 1 e users can remove and install the fan tray without turning off the system power Follow the steps below to replace a fan tray 1 Unfasten the fan tray 2 Slide the fan tray out 3 Insert a new fan tray 4 Fasten the new fan tray The air filter can become dirty after a period of use Follow the steps below to replace a filter 1 Remove the filter cover 2 Replace the dirty filter by a clean one 3 Reattach the filter cover Repeat steps 1 to 3 to replace the other filter MIC 3021 8 User s Manual
7. ity under the terms of this warranty as a consequence of such events Because of Advantech s high quality control standards and rigorous testing most of our customers never need to use our repair service If an Advantech product is defective it will be repaired or replaced at no charge during the warranty period For out of warranty repairs you will be billed according to the cost of replacement materials service time and freight Please consult your dealer for more details If you think you have a defective product follow these steps 1 Collect all the information about the problem encountered For example CPU speed Advantech products used other hardware and software used etc Note anything abnormal and list any on screen messages you get when the problem occurs 2 Call your dealer and describe the problem Please have your manual product and any helpful information readily available 3 If your product is diagnosed as defective obtain an RMA return merchandize authorization number from your dealer This allows us to process your return more quickly 4 Carefully pack the defective product a fully completed Repair and Replacement Order Card and a photocopy proof of purchase date such as your sales receipt in a shippable container A product returned without proof of the purchase date is not eligible for warranty service 5 Write the RMA number visibly on the outside of the package and ship it prepaid to your deal
8. ndles meet the rectangular holes of the cross rails Chapter 2 Installation 17 Note If the card is correctly positioned and has been slid all the way into the chassis the handles should match the rectangular holes If not remove the card from the card guide and repeat step 3 again Do not try to install a card by forcing it into the chassis 5 Pull the upper handle down and lift the lower handle up to push the card into place 6 Secure the card by locking the handles in place Keep your fingers away from this area Fig 2 3 Installing a card into the chassis 18 MIC 3021 8 User s Manual To remove a card 1 Unscrew the screws on the card front panel Release the locking latches on the handles 2 Lift the upper handle up and press the lower handle down to release the card from the backplane 3 Slide the card out 2 3 2 Before Operating the System Before operating your system first check your power supply source Adjust the switch on the power supply to the correct voltage Two mounting flanges are included for users who would like to install the MIC 3021 8 on a 19 rack or on a panel These flanges can be installed on the front side for rack mounting or on the rear side for panel mounting Four rubber stands can be attached to the bottom of the chassis for desktop operation They are not required for rack operation There are ventilation holes on the top and bottom of the chassis for cooling We advise you
9. not to block these holes when installing the chassis on a rack or placing it on a desktop Chapter 2 Installation 19 20 2 3 3 Installing Peripherals The device bay of the MIC 3021 8 accepts up to five devices Howev er the actual available space depends on the system configuration The top tray is designed to accomodate an alarm module the MIC 3921 and or an internal device See figure 2 4 to install a device on the top tray Figure 2 4 Install a device on the top tray The lower two trays are occupied by an ATX power supply therefore they are available only when the system uses an external power supply or plug in power modules The mounting brackets shipped with the chassis are designed for mounting 5 25 devices For mounting 3 5 devices extension brackets are required These extension brackets are available in PC shops or you can contact an Advantech distributor to order them MIC 3021 8 User s Manual Figure 2 5 Attaching the mounting brackets to a 5 25 device Follow the procedures below to install a device 1 Fasten one pair of mounting brackets to both sides of a 5 25 device or a 3 5 device with extension brackets Note that the guide edge of the mounting brackets should be at the lower side 2 Unfasten and remove the cover plate of the device tray 3 Insert the device into the device tray 4 Fasten the mounting brackets then fasten the cover plate for internal devices only 5 Remove t
10. oval The CompactPCI connectors are firm and rigid and require careful handling while plugging and unplugging Improper installation of a card can easily damage the backplane of the chassis The system card can be installed only in the system slot The CompactPCI specification allows the system slot to be at any position in the backplane Do not insert the system card into any other slot or insert a peripheral card into the system slot The MIC 3021 8 may accept different backplanes thus the location of the system slot may vary The system slot is marked by a triangle enclosing the slot number Please refer to the backplane user s manual The inject eject handles on CompactPCI cards help you to install and remove the cards easily and safely Follow the procedures below to install a card into a chassis To install a card 1 Hold the card vertically Be sure that the card is pointing in the correct direction The components of the card should be pointing to the right hand side 2 Be sure that the handles of the card are not latched Release the handles if they are latched Handles from different vendors may have different latch designs Caution Keep your fingers away from the latch hinges to prevent your fingers from getting pinched 3 Insert the card into the chassis by sliding the upper and lower edges of the card into the card guides 4 Push the card into the slot gently by sliding the card along the card guide until the ha
11. the fans Tachometer signals are transmitted to the system through a 6 pin connector on the fan backplane A protective circuit has been designed into the fan backplane to reduce electrical spikes and noise while hot swapping This design allows users to replace fans safely without turning the system off The 7U high design also provides an additional space beneath the device bay to install a 5 25 device The device bay itself accommodates up to five 5 25 or 3 5 devices or three devices when an ATX power supply unit is installed It accepts standard HDDs and FDDs there is no need for expensive special devices Devices can be removed through the device bay front without the need for disassembling the enclosure providing the shortest MTTR for device replacement A lockable door prevents unauthorized access to the devices and to the power on off switch 8 MIC 3021 8 User s Manual 1 2 Features Eight 6U card slots Easy rackmount or panelmount installation Accepts an ATX power supply or two CompactPCI plug in power modules optional Device bay accommodates up to 5 devices secured by a lockable door Front removable devices Hot swappable fan tray Optional fault detection and alarm module 1 3 Specifications 1 3 1 General Construction Aluminum frame and galvanized sheet steel Device bay Accommodates up to five 5 25 or 3 5 devices or three devices when an ATX power supply is installed front removable 12 slot sp
Download Pdf Manuals
Related Search