NA788 ENG IM Y 130819
Contents
1. s negative terminal and make all electrical connections before installing the unit X Insulate unconnected wires with vinyl tape or other similar material To prevent a short circuit do not remove the caps on the ends of the unconnected wires orthe terminals X Be sure to ground this unit to the car s chassis again after installation X If the power is not turned ON the speaker wire may have a short circuit or touched the chassis of the vehicle and the protection function may have been activated Therefore the speaker wire should be checked Wiring Connection Caution X If your car s ignition does not have an ACC position connect the ignition wires to a power source that can be turned on and off with the ignition key If you connect the ignition wire to a power source with a constant voltage supply as with battery wires the battery may die X Install this unit in the console of your vehicle Make sure the faceplate will not hit the lid of the console if any when closing and opening X After the unit is installed check whether the brake lamps blinkers wipers etc on the car are working properly X Mount the unit so that the mounting angle is 30 or less H Ifthe fuse blows first make sure the wires are not touching to cause a short circuit then replace the old fuse with one that has the same rating X Connect the speaker wires correctly to the terminals to which they correspond The unit may be damaged or fail to wo2. DRAMA CULTURE SCIENCE VARIED WEATHER FINANCE CHILDREN SOCIAL RELIGION PHONE IN TRAVEL LEISURE DOCUMENT m ON The unit will be searches for another station with stronger signal but with the same program AF identificati h A icall Alternate Frequencies identification as the current station automatically m OFF Cancel m ON When there is traffic announcement the unit switches to the tuner mode regardless of the TA current mode and begins to broadcast the announcemet on traffic conditions When the Traffic Announcement trafficannouncement is over it returns to the previous mode m OFF Traffic announcement does not cut in RDS On Off Turn On or Off the RDS function Select suitable country region of the radio USA LATIN EUROPE RUSSIA Oirt M EAST ASIA JAPAN AREA AUST Australia LOCALSEEK su more radio stations or only stations with strong signal you can adjust the radio 8 EN Listening to a Disc USB SD device D Press to pause Press again to resume playback 3 Oei Ta ckarrichi Ol m Press to repeat one track press again to repeat all tracks FME PS sw w e2230 T m Press and hold repeat a folder E l u H Hi H M IL H l 6 _ Press to start random play press again to cancel random play T 5 6 m Press and hold random a folder
3. J R Jo 3 5 mm Cable not included 1 Pressthe SRC to select AUX IN mode 2 Turn on the external componentand start playing EN 9 Listening to the iPod iPhone b Bluetooth PlaNakamichi O FRc um 02 38 a e MOL amt rut 5 INIIATIILIIILE gt g pres lt s gt AUX Press to pause Press again to resume playback m Press to repeat one track press again to repeat all tracks A m Press and hold repeat a folder AI m Press to start random play press again to cancel random play m Press and hold random a folder Press to move next previous folder m Press to select a track file Press into search mode m Press and hold for fast forward backward Playing a iPod iPhone 1 Openthecovermarked lt gt onthefrontpanel 2 Insertthe USB adaptoron one endofiPod iPhone cable into the USB socket 3 Press the SRC button to select the USB iPod iPhone mode to start playing iPod iPhone Cable not included Search for music on unit 1 Press A to browse iPod iPhone menu 2 Roate Encoder Volume knob to select the Artist search mode and press OK Mute to confirm 3 Press to search alphabetically 4Roate Encoder Volume knob to select the Album then press OK Mute to confirm 5 Roate Encoder Volume knob to select desire
4. ne Press to move next previous folder m Press to select a track file Press into search mode m Press and hold for fast forward backward Playing a disc USB Smart Phone 1A charging Insert the discinto the Disc Slot with label side facing up 1 Open the covermarked Aes on the front panel Press the SRC button to elect the Disc mode to start playing 2 InserttheiPhone Smart Phone device into the USB socket 3 Once the iPhone Smart Phone is connected and recognized Playing a USB device theiPhone Smart Phone begins to charge 1 Openthecovermarked e lt gt onthefrontpanel 2 Insertthe USB device into the USB socket 3 Press the SRC button to select the USB mode to start playing O L J OH This USB only can charge Phones but cannot play or decode music files Remark This USB is compatible with iPhone iPod USB stick and play the songs in some Hand phone amp recharge them Subject to the brand amp modelarthe Hand oi i i Listening to the other external components Playing a SD memory card _ 1 PressthePanel Release button 2 Pushthe left side ofthe panel rightward 3 Insertthe card into the card slot ai i 4 Close the front panel DA 5 Press the SRC button to select the SD mode to start playing
5. or auto antenna Grey Grey Black relaycontrol terminal Max 150MA 12VDO A7 Red Ignition ACC B5 B6 White White Black Left front speaker A8 Black Ground B7 B8 Green Green Blak Left rear speaker EN 3 Installing the unit Installation with the half sleeve After inserting the half sleeve into the dashboard select the appropriate tab according to the thickness of the dashboard material and bend them inwards to secure the holder in place Bend the appropriate tabs to hold the sleeve a gt firmly in place NN Control panel Installation using the screw holes on the side of the unit Select a position where the screw holes of the bracket and the screw holes of the main unit become aligned are fitted and tighten the screws at 2 places on each side P A Allthe mounting sleeve amp screw are not included in this packing 4 EN Basic Operation Ejects the disc Detaches the control panel D Bluetooth F BNakamichi mz O n E El e2236 R FIS DIL Capa T C La T 3 G INIMINILLIILE ae o ge TT ce EE Z a _ OK Mute Open the cover Encoder Volume Knob Aux In jack When you press or hold the following button s Main unit General operation ZONE Switch mu
6. rear to 12F full front SUBWOOFER ADJUST SUBWOOFER LEVEL Adjust the level 0 to 12 SUBWOOFER LPF Subwoofer low pass filter range 80 120 160 RESUME Resume the preset EQ value to factory default value MENU Item Selectable Setting CLOCK CLOCK SET Adjust the Hours and Minutes CLOCK FORMAT Select the time format 12H or 24H BEEP TONE Turn On or Off this beep sound DEMO To automatically demo this unit s major features cyclic on LCD display SWC SET j Ifyou caris equipped with the steering wheel remote controller you can operate this unit using the controller m Press the OK Mute to access into SWC SET mode m Rotate encoder volume knob to select the function you want the steering remote to learn then press and hold the same function button on the steering wheel remote until SUCCEED is displayed RGB COLOR This unit is equipped with variable color display Once into the RGB COLOR mode rotating encoder volue knob to selected the LCD color m COLOR SCAN default setting WHITE GREEN 1 GREEN 2 GREEN 3 AMBER PINK 1 PINK 2 PURPLE 1 PURPLE 2 BLUE 1 BLUE 2 ORANGE USER COLOR SCAN ZONE This innovative Zone technology enables driver or passengers to enjoy music with the best speakers balance and experience a more vivid spacial effect as the artist is intended to create User can switch the music listening zone from driver to passengers for the best speaker sound settings in car 1 Press the ZONE button The curr
7. 7 BNokamichi NA788 Car Audio System Player INSTRUCTION MANUAL CD MP3 WMA USB SD AUX IN BT iPod iPhone USB 1A Smart Phone Battery Charge Safety WARNING Stop the car before operating the unit Important to know X To prevent a short circuit never put or leave any metallic objects such as coins or metal tools inside the unit Caution Adjust the volume so that you can hear sounds outside the car Driving with the volume too high may cause an accident Condensation When the car is air conditioned moisture may collect on the laser lens This may cause disc read errors In this case remove the disc and wait for the moisture to evaporate X The illustrations in this manual are examples used to explain more clearly how the controls are used Therefore what appears on the illustrations may differ from what appears on the actual equipment X If you experience problems during installation consult your Nakamichi dealer X When you purchase external components check with your Nakamichi dealer to make sure that they work with your model and inyourarea Maintenance Cleaning the unit Wipe off the dirt on the panel with a dry silicon or soft cloth Failure to observe this precaution may result in damage to the monitor or unit Cleaning the connector Wipe off dirt on the connector of the unit and faceplate Use a cotton swab or cloth Preparation How to attach detach the faceplate Attach i Detach X
8. Do not expose the faceplate to direct sunlight excessive heat or humidity Also avoid places with too much dust or the possibility of water splashing Keep the faceplate in its casing while detached X The faceplate is a precision piece of equipment and can be damaged by shocks orjolts 2 EN X To prevent deterioration do not touch the terminals of the unit and faceplate with your fingers How to reset your unit X If this unit fails to operate properly press the reset button X The unit returns to factory settings when the reset button is pressed What s in the box Check and identify the contents of your package Main unit with sleeve Front panel Trim plate Remote ISO male Screw x 4pcs control connector P E Hexagon head Rubber cushion User manual screw _ Installation Connection Basic Procedure 1 Remove the key from the ignition switch then disconnect the terminal of the car battery 2 Make proper input and output wire connections 3 Install the unit to your car 4 Reconnect the terminal of the car battery 5 Reset the unit Warning The DI only be installed in a car with a 12 V DC power supply negative ground X Ifyou connect the ignition wire red and the battery wire yellow to the car chassis ground you may cause a short circuit that in turn may start a fire Always connect those wires to the power source running through the fuse box Disconnect the battery
9. ard Support type of memory card SD SDHC 12 EN Bluetooth Output power Class 2 Frequency band 2 4000GHz 2 4835GHz ISM Band Range 3 meters free space Standard Bluetooth 2 0 specification About Audio file USB or memory file system FAT16 FAT32 MP3 WMA bit rate 32 320kbps and varible bit rate MP3 sampling frequencies 8 48kHz WMA sampling frequencies 32kHz 44 1kHz 48kHz D3 tag v1 0 or later USB Smart Phone 1A charging Output Voltage 5 V DC Output Current 1000 mA 1A A 7 BNokamichi www nakamichicaraudio com gt
10. d song in the current album press OK Mute to confirm start play Remark To go back to upper level of a folder press 10 EN Search for music on iPod iPhone 1 Press H onfront panel to switch the iPod iPhoe control mode 2 Use the iPod iPhone to search operates music control Remark Please make sure the iPod iPhone cable is connected correctly And please only use original iPod iPhone cable not supplied Compatible iPod iPhone Apple iPod and iPhone models with a 30 pin dock connector iPod nano 2nd generation iPod nano 3rd generation 4GB only iPod nano 3rd generation 8GB only iPod nano 4th generation iPod nano 5th generation iPod classic 1st generation iPod classic 2nd generation iPod touch 1st generation iPod touch 2nd generation iPod touch 3rd generation iPod video 30GB 80GB only iPhone iPhone 3G iPhone 3GS IPhone 4 iPhone 4S iPhone 5 TL Operation of Bluetooth Hands Free amp D Bluetooth FBNokamichi O lt H From pE 38 oS NCL Capa TO LA T 3 3 INT IMI LL 6 ap oop eos i vi m Press to answer accept the call i m Press and hold to transfer the call 2 Press to reject end the call Press to change to BT AUDIO mode To redial numbe
11. ent setting is displayed 2 Press the ZONE repeatedly to select one of the below setting FRONT ALL All FRONT LEFT Left FRONT RIGHT Right ZONE OFF Off EN 7 Listening to the Radio m Hold for about 2 seconds to memorize the current station m Press briefly to recall memorized station In receive tracffic press to cancel receive the current traffic 1 Press A repeatedly to a band FM1 FM2 FM3 3 Press O repeatedly to view RDS received information AM1 MW1 or AM2 MW2 2 Press I44 bbI tosearchforastation Adjust MENU mode settings While listening to the radio e MENU 1 Pressandhold J toenterinto the MENU mode 2 Press I4d lt bDI repeatedly toselecttheitem to be adjusted 3 Turn theencodervolume knob toselecta value option Item Selectable Setting AUTO STORE 1 Press the OK Mute to access into Auto Store mode the six strongest stations of the selected band are saved in preset channel automatically FM1 FM2 FM3 1 6 AM1 AM2 Once into the PTY mode press the OK Mute get into program type item and rotating encoder volume knob to selected category PTY Available Program Type p 7 POP M ROCK M EASY M LIGHT M CLASSICS OTHER M JAZZ M COUNTRY NATION M OLDIES M Program Type FOLK M A TEST ALARM NEWS AFFAIRS INFO SPORT EDUCATE
12. etting mode 1 gt i Pause resume playback of a Disc USB SD device iPod iPhone EN 5 _ Remote Control Operation PBNokamichi When you press or hold the following button s Main unit General operation nk Turn mute or restore volume O Press turn the unit on or off w Press increase the volume VOL Press decrease the volume Under Radio mode to enter into the Auto Seek mode press and hold to enter into the Manual Seek mode 144 gt gt Under Media playback mode to skip track file press and hold to fast forward backward SRC Selects the available sources Radio Disc USB USB iPod iPhone SD BT AUDIO or Aux In if the power is turned on AUDIO Press to access into the Audio Menu mode 6 EN Function Settings ENU 1 Press toaccessinto the AUDIO MENU mode press and hold to enterinto the MENU mode 2 Press Id lt 4 bDI repeatedly toselectthe item to be adjusted 3 Turnthe encoder volume knob to select a value option AUDIO MENU Item Selectable Setting BASS ADJUST BASS LEVEL Adjust the level 7 to 7 MIDDLE ADJUST MIDDLE LEVEL Adjust the level 7 to 7 TREBLE ADJUST TREBLE LEVEL Adjust the level 7 to 7 BALANCE Adjust the balance between the right and left speakers from 12R full right to 12L full left FADER Adjust the fader between the front and rear speakers from 12R full
13. g call the phone number is displayed if the incoming call has no phone number PHONE IN is displayed 2 Press toanswer acceptthe call 3 When conversation ends press F gt toterminate the call Call Transfer You can transfer voice from loudspeaker to mobile phones during call During talking press and hold Z loudspeaker to mobile phone voice transfers from Bluetooth Audio Streaming A2DP If the connected Bluetooth device supports Advanced Audio Distribution Profile A2DP you can listen to the music stored on the device through the unit If the device also supports Audio Video Remote Control Profile AVRCP profile you can use the control on the unit or its remote control to play music stored on the device 1 Press SRC repeatedly to select BT AUDIO 2 Press II tostart play pressitagain to pause 3 Totrackup down press 144 ppt EN 11 Product Information General Power Supply 12V DC 10 5 14 4V negative ground Fuse 15A Suitable Speaker Impedance 4 80 Aux In level 800mV Audio Section Maximum Power Output Mosfet 50W x 4 Channels Continous Power Output 24W x 4RMS Pre AMP Output Voltage 4V Subwoofer Output Voltage 3V FM tuner section Frequency Range 87 5 108MHz Usable Sensitivity Better than 15dB at S N 30dB AM tuner section Frequency Range 522 1620KHz Usable Sensitivity Better than 45dB at S N 26dB USB devices USB Flash Memory USB 1 1 amp 2 0 Compatible Memory C
14. r You can make or receive phone calls with Bluetooth enabled phones through the unit You can also listen to music from a Bluetooth enabled device Getting Started Before use the Bluetooth device you need to pair the device to theunit Pairing needs only to be done once Pairing the Bluetooth devices 1 Open your mobile phone and switch bluetooth on 2 Search for other bluetooth device with your device 3 Select NAKAMICHI in the pairing list 4 Input the password 0000 5 Pairing OK will be displayed on the screen if pairing is successful and the paired device will connect to the car audio system automatically Disconnect the bluetooth 1 Pressand hold eni to enterintothe MENU mode 2 Once the DISCONN is displayed press OK Mute to activatethemanual Disconnectmode Re connectthe bluetooth 1 Press and hold TN to enterintothe MENU mode 2 Once the BT CONNECT is displayed press OK Mute to activate the manual Re connect mode Making a Call Youcan dial numberthrough the mobile phone 1 Use the Mobile Phoneto dial and make an outgoing call 2 Once completed the dialing CALLING is displayed 1 Press Z onfrontpaneltoredial 2 Press onceagain unitwill display CALLING and the unitstarts dialing the number dialed last time Remark To make an outgoing call on this unit the bluetooth connection between the unit and the phone must be active Receiving a Call 1 If there is incomin
15. rk if you share the O wires or ground them to any metal partin the car X When only two speakers are being connected to the system connect the connectors either to both the front output terminals or to both the rear output terminals do not mix front and rear Mounting and wiring this product requires skills and experience For safety s sake leave this work to professionals If you experience problems during installation consult your Nakamichi dealer Bluetooth External Microphone J OE Steering learning Remot i c eering learning Remote Gray GND es Wa Ce Steering wheel Rr Tr tic ie Lo OE external remote Purple D 9 150 INI nd 8 1 lt On Q OF r rote adapter S Lai Li z VN not supplie L le Gi Sa TS Antenna Jack not included Il j Subwoofer Output LToms 7 Rear RCA Output Left L Front RCA Output Left B 2 4 6 B Rear RCA Output Right Front RCA Output Right 5 E A 4 E ISO Connector Wiring Chart Pin Color and function Pin Color and function A4 Yellow Battery B1 B2 Violet Violet Black Right rear speaker AS Connect to system control terminal B3 B4 Right front speaker Rive of the power AMP
16. sic listening zone for the best speaker sound FRONT ALL FRONT LEFT FRONT RIGHT ZONE OFF EG Toadjustthe EQ Preset Equalizer setting XBSS TurnOnorOfftheXbass bossterfunction Bj To turn On or Off dynamic bass boost sound DBSS m Press and hold to enter into iPod iPhone control mode e MENU Toaccessintothe Audio Menu mode J pressandholdtoenterinto the System Menu mode S EWE m Under Media playback mode to view play informations Under RDS mode to view RDS received information Press and hold turn On or Off the subwoofer function 144 D I m Under Radio mode to enter into the Auto Seek mode press and hold to enter into the Manual Seek mode m Under Media playback mode to skip track file press and hold to fast forward backward Turn the unit on Press and hold again to turn the unit off SRC m Select the available sources Radio Disc USB USB iPod iPhone SD BT AUDIO or Aux In if the power is turned on Turn mute or restore volume OK Mute Confirms selection Rotatory Rotate it to increase or decrease the volume Volume knob Select items Q m Select the FM bands FM1 FM2 FM3 or AM1 MW1 AM2 MW2 BAND Under media playback to access into search mode METE m Toanswer accept the call pi Duringthetalking pressandholdtotransferthe call inten m Toreject end the call Returns to the previous item Press and hold access into the VRD display color s
Download Pdf Manuals
Related Search