CIE-H10 User`s Manual
Contents
1. DATA GHI TCP IP DATA GHI COD connection sequence Byte Count 3 3 Serial Data before Connection Data before TCP connection will be handled based on the Byte Count settings If the Byte Count is 0 the data that comes to CIE H10 s serial port will not be recognized If it is not 0 the serial data before TCP connection will be temporarily saved to be sent to the host after the connection 3 2 Data Communication When the TCP connection is established the data communication in between the host and the serial device will be established Then CIE H10 will send data according to the Guard Time In other words when the data comes through CIE H10 s serial port it will be temporarily saved in the buffer Then when there is no incoming data during the designated Guard Time CIE H10 will send the saved data If the Guard Time is 0 CIE H10 will send serial port s data immediately The unit used for the Guard Time is 10m seconds and its minimum value is 40m seconds Therefore the user must set the number that is greater than 4 EC 6 3 3 Connection Termination When the connected host terminates the connection or there is no data communication during the designated Timeout the TCP connection will be automatically terminated The unit used for Timeout is 1 second E 6 4 ATC ATC mode allows users to use AT commands to control CIE H10 like modem control In AT2. operand is 0 it will be changed to 1 If it is 1 it will be changed to 0 If Operand values that surrounds AND operator all 1 the result value will be 1 If either one of them is 0 the result will be O as well 29 If Operand values that surrounds AND operator all 0 the result value will be 0 If either one of them is 1 the result will be 1 5 2 2 Operand Operands used in macro mode are each input port Each input port 1s designated with 10 17 symbol based on their sequence Since capital letters are not recognized they can also be written as IO I7 5 2 3 Example of Equation Let s assume that the equation settings are the same as the following ezlCP Manager v1 3d 29 May 2007 BREER T EER EN er LOCAL REMOTE NETWORK OPTION INTERFACE VO INTERFACE MAC Address j BO CQC Ox QA Option Input Output Ports foo 30 oo on o6 Da Digital Input Digital Output Valid Tme V Macro Delay tal ms State Search List CoD i2 l E Dot Do2 0 17 Do3 l mm Em Change Pwo TT wirixP Firewall earch ez Write Status Debug Message ezT CP Test In this case the equations for two output port are as the following Perform OR for 10 and 11 Spaces in between two operands may be ignored Perform NOT with value from performing OR for 11 and 17 Then perform AND with that value and 10
3. 17 17 Lr LIT Br 17 17 17 17 17 17 17 17 17 17 17 MAC 00 30 F9 06 00 02 00 30 F9 06 00 02 00 30 F9 06 00 02 00 30 F9 06 00 02 00 30 FA 06 00 02 00 30 F9 06 00 02 00 30 F9 06 00 02 00 30 F9 06 00 02 00 30 F 9 06 00 0E 00 30 F9 06 00 02 00 30 F9 06 00 02 00 30 F9 06 00 02 00 30 F9 06 00 02 00 30 F9 06 00 02 00 30 F9 06 00 02 00 30 F9 06 00 02 00 30 F9 06 00 02 00 30 F9 06 00 02 00 30 F9 06 00 02 00 30 F 9 06 00 0E 00 30 F9 06 00 02 00 30 F9 06 00 02 00 30 F 9 06 00 0E 00 30 F9 06 00 02 00 30 F9 06 00 02 00 30 F9 06 00 02 Dump Start This function 1s very useful when there are any problems when user install the CIE H10 in the user site Message 452 ip 453 ip 464 ip 4651 ip 466 ip 457 ip 458 ip 469 ip 470 ip 471 ip 472 ip 473 ip 4141 ip 4751 ip 4761 ip 477 ip 478 ip 473 ip 4501 ip 481 ip 482 ip 483 ip 404 ip 485 ip 4061 ip 487 ip sent rc vid sent reyd sent rvd ICM sent revd ICM sent reyd ICM sent reyd ICM sent reydi ICM sent revd ICM sent reyd ICM sent reyd ICM sent rvd sent reyd ICM sent reyd 10 1 0 156 1470 10 1 0 156 1470 10 1 0 155 1470 10 1 0 155 1470 10 1 0 156 1470 10 1 0 156 1470 10 1 0 155 1470 10 1 0 156 1470 10 1 0 156 1470 10 1 0 15
4. Based on input values from three input ports the output values are as the following 30 Output ports that equations are not applied will be maintained as 0 OFF Co Papo eor o pe n os De oe GC lG lea lea lea l 5 3 Monitor and control using Web HTTP When HTTP check box in ezManager is selected CIE H10 input output port values may be monitored and controlled using web browser 5 3 1 Connect to Web After starting the web browser type in CIE H10 s IP address after typing http in the address window to connect to CIE H10 If passwords for CIE H10 are designated the following window will pop up Connect to 10 1 0 1 CIE H10 Autharization User name E admin Password _ Remember my password In this case enter admin for ID and designated password This 1s the initial window when users connect to CIE H10 EP 3 CIE H10 Microsoft Internet Explorer File Edit View Favorites Tools Help Q pack E N D E 5 pi Search SP Favorites Qi Media ES Address El http 10 1 0 ij CIE H10 o o b Internet 5 3 2 Read Write Using Web Current input ports values will be shown in DIO D17 check boxes and output port values will be shown in DOO DO7 check boxes These values represent CIE H10 status the moment web browser is connected to CIE HIO and will not change automatically as the CIE
5. With ezManager provided by Sollae Systems or with web browser the test operation may be performed For more details please refer to 3 2 test operation NE 9 2 Test operation The test operation may be performed according to the following procedure The test operation suggested in this manual is based on the assumption that IP of PC is set as 10 1 0 2 3 2 1 PC IP Address change D Change IP address of PC as the following IP address 10 1 0 2 255 0 0 0 Gateway IP address ie 2 2 CIE H10 Installation Connect LAN cable directly to the LAN port of CIE H10 or connect it to the hub where PC is connected to Also provide power to CIE H10 using CIE H10 power adapter When the power is connected the LINK LED will light up when a proper connection to the LAN cable is established 3 2 3 CIE HIO Setup Using ezManager change the settings of CIE HIO Start ezManager and click Search ezTCP button on the ezManager window Then ezManager will search for every ezT CP on the local network When there is no result click WinXP Firewall button on the ezManager window to check for firewall setting value If there is a firewall the program cannot perform the search When CIE HIO is found the MAC address of CIE HIO will be shown on the Search Results window The MAC address is also written on the bottom of the product case Select the MAC address and set its value as same as the values shown in the photos below Then
6. click Save to save the setting values 14 ezTCP Manager v1 5e 1 Sep 2007 LOCAL REMOTE MAC Address Network EN Ca En Cal A As Subnet Mask Gateway IP Search List DNS IP Address 00 3079 07 31 01 Option ARP bBHCP PPPoE Obtain DNS server address automatically PPPGE PPPaE Password DDNS Service provider User id Host name Change Pwo WIG Firewall Sehen C wie JL sae ERE n Exit Comment LOCAL REMOTE VO INTERFACE MAC Address jon 30 ta 07 e1 01 Multiple connection mr man Search List Ede m Do ezTCP Access Lock Allowed Ethemet Address DOD TT eere C wae JL Se EE E Cra Comment 15 ezICP Manager v1 5e 1 7 Sep 2007 LOCAL REMOTE NETWORK OPTION INTERFACE O INTERFACE MAC Address OEE fon m Search List Hdd T25 0 TCP Server we Local Fort D0 30T3 07 81 01 1470 Peer Address Peer Port p Timeout Byte Count oe fo Guard Time 10ms Telnet COM port control option Change FWO WinsP Firewall E 00 3079 0781 01 Unit ID Input port address Qutput port address Active Passive Connection Peer Address Part Comment 16 ezTCP Manager v1 5e 17 5ep 2007 LOCAL REMOTE NETWORK OPTION INTERFACE VO INTERFACE MAL Address Option Input Output Ports 00 30 ta o7 61 01 Digital Input Digital Output Valid Time Delay
7. 18H 1 H 1 4 1478 H H H B A gt B LISTEN 1H 1 H 1 56022 4 8 6 8 A gt H LISTEN O Serial Ports Status User can monitor the statuses of the serial port with the st sio command The tx_count and the rx count are the total data sizes to from the serial port The coml is the CIE H10 s serial port and the com2 must be ignored CA ER ul 1 0 1 s DO 1 lsh gt s t sio port fmax rhmax rxbuf txbuf rx count tx count 49 9 2 Status of ezManger If the Status is pressed user can monitor the current status of the CIE H10 with ezManager If user sets Status Request option the status data will be updated periodically ezICP Internal Status FIRMWARE VERSION CIE H10 7 1 0 Rev SYSTEM UPTIME U days 00 42 50 45 IF4 NETWORK INFORMATION Device IP address 101 01 Subnet mask 255 0 0 0 Gateway 0 0 0 0 Mame Server 0 0 0 0 TEP STATE 5100 LISTEN MODELS LISTEN SERIAL STATUS SIDO sin r U sin tk U net rg 0 net ts U IO PORT STATUS IM U U 0 0 U U U U OUT U U U U 0 0 0 U Interval T Second s Status Request 9 3 Remote Debugging If the Debug field in the OPTION tab of the ezManager CIE HIO transmits debugging messages with UDP port 50006 Then user can get the messages with new window if user presses Debug Message button as followed 50 DEBUG MESSAGE Time 17 30 56 263 17 30 55 263 17 17 17 17 17 17 17 17
8. 3 Connect via Web Browser When connecting to CIE H10 that has designated password via web browser password must be entered Enter admin for ID and enter designated CIE H10 password in the password window Connect to 10 1 0 1 CIE H10 Autharization User name admin v _ Remember my password 8 1 4 When Password is Lost When designated password is lost ezManager cannot be used to manage CIE H10 In this case pres CIE H10 s ISP button for 100ms to operate CIE H10 in ISP mode In ISP mode all of the security functions are disabled It allows users to delete currently designated password 46 8 2 Connection Restriction Function When ezTCP Access Lock is selected in ezManager host connection can be restricted This function is applicable to Modbus TCP HTTP telnet and other TCP connections ezTCP Manager v1 3d 29 May 2007 LOCAL REMOTE _ NETWORK OPTION INTERFACE 140 INTERFACE MAC Address OPTIONS 00 30 f8 00 00 06 Z Remote Search PD Em EE Comments ez CF Access Lock C Allowed Ethemet Address Ai d i ded L 41 Mimi C Allowed IP IP address NetMask Of of of ol Hees hezTCP Change PD Wi resP Firewall earch ez 8 2 1 Allowed Ethernet Address Host s MAC address that attempts to establish connection to CIE H10 may be restricted When this category is selected hosts with designated MAC address may only connect to CIE H10 8 2 2 Allowe
9. GSS1VE C ONNCCHON A das di eat 43 dsd EXAMPLE FOR CONNECTION TERMINATION sees sese enen 43 7 7 1 Example for Active Connection Termination seen 43 7 7 2 Example for Passive Connection Termination sss eee eee eee eee eee 44 8 SECURITY FUNC TION cuac 45 8 1 FASSWORD MA es 45 Oeds Set and Delete Fasswobd us Rue reete qe 45 8 1 2 CIE H10 settings with Designated Password Ge Ee ee ee SE essa 45 Old AE RD BROWSE AE EE N EE EE EE RE 46 Odo Wien T ass WOT IP LOSE scito ot dai ci 46 8 2 CONNECTION RESTRICHON FONCTION usa 47 Oele Allowed Eihernel ARSS cre s nU Ie UOI atum anaes eae Se De 47 Oud AOW AIP ADI CSS n E apa ee Ee ee eade esie ced 47 RE EL AE se AIR TEE EE KENS RE AT 48 25020 0 02 11 L 6 1 Leser 49 C ROEM RE OE AE EE EE 49 DEEL E A ger che ta MU DM edi MU M 49 Ole ER EE EE EE EE EE E NE NE 49 92 STATUS OFZ MANGE AE RE iaa 50 DO REMOTE DEBUG IN G soets ee id dalla 50 10 TECHNICAL SUPPORT GUARANTEE PERIOD PRECAUTIONS 52 LOE TECHNICAL SUPPORT satelital 52 IU GUARANTEE ea RE EO RE N N oats oe 52 Mi EE ME NEE N RE EL OE ENE 52 10 2 2 COMO CAS GUC ATS cose EE chal o UO 52 TUUS AN ONACOMPCNS died ATS T 52 10 PRECAUTION S ETT 52 LH REVISION HISTORY esse ese EG ee Ee ee WE ese Ne ee ee ees ee oes ee ee ed Ee 54 1 Introduction 1 1 Introduction The need for the data co
10. H10 s status changes Therefore users must click Read in order to read current updated values In order to output values designated by the users designate output values for the desired output port and click Write If the macro function is activated users cannot control device s output port using HTTP Users may only read input output port values z3 6 Serial Interface CIE H10 provides RS232 TCP IP conversion function along with input output port monitor and control function Using this function existing serial devices may be easily connected to the TCP IP network Also TCP server TCP client AT command emulation UDP and many other devices are supported to provide various applications to the users 6 1 Serial communication mode CIE H10 has 4 serial communication modes The following chart is a brief explanation for each communication mode Need for User Designation of Communic Device Environmental Protocol Connection l Topology ation mode S W Factor via Serial Modificat Port ion Passive Not l l Not possible Connection required Active Passiv l required possible e 1 1 1 1 1 1 M Active Not l COD TCP l l Not possible connection required No Not l U2S UDP l l Not possible N connection required Ed 6 2 T2S Mode T2S is the mode that CIE H10 s serial port operates as a server When TCP connection comes through previously designated Local Port from remote host CIE H10
11. users to quickly respond to the problems that might occur during the installation 2 Product Specification 2 Components CIE H10 body 5V Power Adapter Option RS232C Cable for PC Option Cross over Ethernet cable Option Adapter for DIN rail Option 2 2 Product Specification Power 153mm x 126mm x 32mm Approximately 530g 8 Port Photo coupler Interface Dsub 9Pin male 10 100 Base T RJ45 Ethernet 10 100 M bit auto sense Network Auto MDI MDIX Cable Auto sensing TCP UDP IP ICMP ARP DHCP PPPoE DNS lookup Dynamic DNS DDNS Telnet COM Port Control Option RFC2217 MODBUS TCP HTTP Online Debugging Function Follows Europe RoHS Regulation CE F690501 SP EMC000976 MIC SLS CIE H10 Modbus TCP Slave Master Passive Active Input Output Communicati Web Browser HTTP Port on Mode Macro Movement Macro TCP Server Client AT emulation UDP Set up program via LAN Programs Protocol Certification Socket communication program for testing Firmware download program using TFTP 2 3 Interface 2 3 1 Input Port Since CIE H10 input port is isolated by photocouplers users may connect the machine regardless of its polarity The circuit of the input port is shown in the below It is the part where the EXTERNAL INPUTI and EXTERNAL INPUT2 are interfaced with the user device gt TO PROCESSOR EXTERNAL INPUT EXTERNAL INPUT The specifications of the input port are as the fo
12. 5 1470 10 1 0 155 1470 10 1 0 156 14 10 1 0 156 1470 5 gt Auto Scroll 10 Technical Support Guarantee Period Precautions 10 1 Technical Support If there are any questions regarding the product please use FAQ or Q A board in Sollae Systems s homepage Also feel free to contact us by email Customer support homepage address http www sollae co kr Support email address support sollae co kr 10 2 Guarantee 10 2 1 Refund If user demands refund within 2 weeks of purchase the product will be refunded 10 2 2 Compensated A S If product malfunctions within 1 year of purchase repair and product exchange will be done without charge However product malfunctions due to user s miss care will be repaired with charge 10 2 3 Non compensated A S Products after 1 year of purchase or product malfunctions due to user s miss care will be repaired and exchanged with charge 10 3 Precautions If the product is modified the product is no longer guaranteed The specifications of the product may be altered without notice If the product is used for functions that are not covered by the product the product is no longer guaranteed as well Reverse engineering of provided applications and firmware is prohibited Firmware and provided applications may not be used for other purposes that its original purpose Do not use the product in extreme temperature or vibration conditions Do not use the product in highly humid a
13. C mode only TCP connection is allowed In ATC mode AT commands can be used to change environmental factor values and IP address Also it allows users to establish and terminate TCP connection Remote Host CIE H10 Serial Device Listen Set IP and port by using AT commands Request TCP connection ADT Accept TCP connection CONNECT connected K de KERR ERROR MN ACC ARS DA pO ACA Wow DOE Sb ex Ux der e ow de Ve We uy DATA ABC DATA ABC TCP IP DATA DEF TCP IP DATA DEF lt ATC connection sequence active connection gt Remote Host CIE H10 Serial Device Set IP and port by using AT commands Listen on Ee Reguest T Local port alls CP connection Se Accetp TCP connection CONNECT connected DATA ABC DATA ABC TCP IP DATA DEF TCP IP DATA DEF lt ATC connection sequence passive connection gt c Detailed information on AT commands are given in the next chapter sd qus 6 5 U2S U2S 1s a mode that performs UDP communication In UDP communication data is sent in block units Therefore data that comes through CIE H10 s serial port must be classified in block units to send it elsewhere The block unit classification process 1s performed as the following When the amount of received data via CIE HIO serial port is as same as previously designated
14. CIE H10 User s Manual Version 1 5 Souad Sollae Systems Inc To all residents of the European Union Important environmental information about this product This symbol on this unit or the package indicates that disposal of this unit after its lifecycle could harm the environment Do not dispose of the unit as unsorted municipal waste it should be brought to a specialized company for recycling It is your responsibility to return this unit to your local recycling service Respect your local environmental regulation If in doubt contact your local waste disposal authorities L 1 1 2 Zw Za 2 5 Za 2 9 2 E 2 3 4 ZR 2 3 6 PERA 3 3 1 JA Sud 2 3 4 3 3 1 4 Za 3 2 1 Se Dus 3 2 4 3 2 9 4 4 1 4 2 c 4 2 2 4 2 3 4 2 4 4 3 Table of Contents INTRODUCTION cuasi dida 6 INTRODUCTION esdorpen cete dU EO EE acid 6 PRODUCT SPECIFICATION iese ses des sees ese an ea a ERR uaa NER Ge ee Na AN AG KA Pan aaa ke 7 KOLA AN 7 PRODUCT SPECIBIC ATION estas eoi ri eb Doe ia 7 INTERFACES adela 8 PR TIN Me EE N EE 8 AE dade MT 8 RSZ Pot OBD IV TM Emm 10 EME T 10 T ONT lend Il NA EE EE OE EE OE OR EE E I2 SEP SUE E ER A I2 TEST OPERA HION eer 13 INS FAME ATION PROCEDURE 255589 ia israel cs 13 Communication Environment Con re ve Re essen I3 NEON ONCOL Het SO eee en
15. In this case it is very hard to communicate to the host because the IP address is changed dynamically The DDNS function solves this problem If the CIE H10 obtains its IP address it notice to the service provider Then the service provider serves DNS service So even though user doesn t know the CIE H10 s IP address user can connect to the CIE H10 by the host name after DNS looking up The DDNS service provider that the CIE HIO supports is only Dyndns http www dyndns com currently 205 5 I O Interface In CIE H10 there are 8 input ports interfaced by photo couplers and 8 output ports interfaced by relays These I O ports can be controlled by three methods Modbus TCP Macro and Web HTTP Modbus TCP protocol is used to communicate with CIE H10 When CIE H10 is in Slave Passive mode it operates as a normal Modbus TCP Modbus TCP device Master operation may be activated by other settings It also can establish TCP Active connection It is a mode that allows the users automatically controls output port s value based on input port status by setting Macro values prior to CIE H10 operation During Macro operation current status values may be read using HTTP or Modbus TCP but output values may not be controlled HTTP may be controlled and monitored using web browser Connect to CIE H10 s IP address via web browser to access CIE H10 s control and monitor web page This webpage shows Web HTTP mE current st
16. Initial ms pMa ms State 00 30339 07 31 01 EES EES Comment 3 2 4 Modbus TCP Test It is a test of CIE H10 to perform control and monitor functions using Modbus TCP This test should be performed with Modbus TCP program provided by Sollae Systems ezTCP Manager v1 5e 17 Sep 2007 LOCAL REMOTE NETWORK OPTION INTERFACE 1 0 INTERFACE MAC Address Input Output Parts oo 3o rs o7 81 or Modbus 00 3049 07 81 01 Modbus TCPNCIE H10 Test 2 Poll nn Unit 1D E Input port address Output port address ArtivesPassive Connection Peer Address Part Passive me En Comment ae eee After having settings as same as the settings shown CIE HIO Test E above click on the CIE H10 TEST button A new Loss pt RUS TUNES Dio e Dall window on the ezManager will pop up Di Doi O Click Connect button to connect to CIE Di2 Do i3 Dios H10 by TCP connection nid nod e In order to check for the Digital Output DiS A Dos Dib Dob port click on DoO to Do7 buttons of the Ss x ss Digital Output to check for output values P Address being sent Port e When the Start Write button is clicked PC previously designated values will be sent to the Digital Output port periodically o Interval 1000 e In order to check for the Digital Input port gt click Start Read button to read values off of the Digital Input port every period designated by the Interval value 3 2 5 T
17. P Address and address range designated in address ezManager s Allowed IP to be connected to CIE H10 ezManager Hosts designated in Allowed Ethernet address and Allowed IP Lock Address may search the CIE H10 through ezManager 4 2 4 ezManager Operation Example ezManager can be used to change IP address related settings of ezTCP The Following example will show you how to read CIE H10 s setting values and change those settings Please follow this procedure to change the setting values of CIE H10 When ezManager s Read or Search ezTCP button is clicked the following window will pop up ezManager Searching ez TCF When ezTCP that is connected to the network is found the following message will pop up If it says that there is no response from ezTCP check for ezTCP s power LAN cable connection or Windows Firewall status before clicking Search ezTCP or Read button again The protocol and the port used by ezManager are UDP port 50005 The debugging port 1s 50006 ez Manager Searching ez T CP 1 esl CPs found 2595 e If 1 ore more ezTCP is found MAC address will be shown in the ezManager s Search Result box Check to make sure that the MAC address shown in the Search Result window is as same as the MAC address written on the product s sticker e Use PING command in Windows DOS window to confirm CIE H10 s IP address The following message will be shown after the PING command when t
18. ager v1 5e 17 Sep 2007 LOCAL REMOTE NETWORK OPTION INTERFACE MAC Address dio Foo I 30 ml 00 I 00 n Local IF Address Ema N ed en Subnet Mask Gateway IP Search List DNS IP Address Option PPPoE PPPoE Password DDNS Service provider User id User password Host name EE sd Change PwD WirkP Firewall Search ez TCF Wy rite Status Jebug Message ezTCP Test Comment ezManager communicates with CIE H10 via UDP broadcast The port used during the communication is 50005 and the UDP port used during the debugging process is 50006 If the firewall functions are being used the firewall functions for the 50005 and 50006 port must be turned off 20 4 2 2 ezManager Buttons Search ezICP Save Change PWD Debug Message WinXP Firewall Search for all CIE H10s series connected to the local network The search results will be shown on the Search Result box Using mouse or cursor the desired products may be selected The values shown on the box are MAC addresses of each ezTCP and the selected ezTCP s setting values will be shown on the right The MAC address of CIE H10 is written on the bottom of the product Input 6 digit number written on the CIE H10 product sticker to the MAC ADDRESS input box or Input CIE H10 s IP address in the IP address category on the REMOTE tab This will allow the user to read setting values for a specific CIE H10 When there are too many ezTCPs
19. atus values By clicking Read button current input output values will be read Also change check box values of output port and click Write to change output port value 5 1 Modbus TCP Since CIE H10 s input and output port is operated based on Modbus TCP CIE H10 can be controlled and monitored using Modbus TCP Manager Currently CIE H10 only supports Read Multiple Function Code 3 and Write Multiple Function Code 16 codes from Modbus TCP Function Code Also along with Modbus TCP CIE H10 s Active TCP connection Modbus TCP master and Input Change Notification functions may be used to apply the product to many other fields When the Macro function is activated users can only read current values using Modbus TCP but is not able to output values via output port HO AR 5 1 1 Modbus TCP Setting Values Modbus TCP Using Modbus TCP monitor and control CIE H10 Like Modbus TCP s standard protocol CIE H10 will operate in Slave mode When CIE H10 receives Modbus TCP query from Slave Master it will process the designated query However in order for CIE H10 to process the inputted query the query must match Unit ID and Input port address Output port address CIE H10 is operated in master mode When CIE H10 connects with designated address it will send Read Multiple queries to previously designated slave s Unit ID and Input port address Tn every Pol Interval The response value will be outputt
20. buffer Then when there is no incoming data during the designated Guard Time CIE H10 will send the saved data If the Guard Time is 0 CIE H10 will send serial port s data immediately The unit used for the Guard Time is 10m seconds and its minimum value is 40m seconds Therefore the user must set the number that is greater than 4 6 2 4 Connection Termination When the connected host terminates the connection or there is no data communication during the designated Timeout the TCP connection will be automatically terminated The unit used for Timeout is 1 second 35 2 6 3 6 6 COD COD mode is the mode that CIE H10 operates as a client When previously designated byte count data comes through the serial port CIE H10 will try to connect to the previously selected Peer IP Address host s TCP port peer port via TCP connection When the remote host accepts the TCP connection the TCP connection will be established After the connection is established the data that comes through the serial port will be sent to the remote host after TCP IP handling The TCP IP data that comes from the remote host will be sent to the serial port after TCP IP handling to form data communication Remote Host CIE H10 Serial Device Listen Request TCP connection Accept TCP connection connected NEN DATA AB DATA C DATA ABC TCP IP DATA DEF DATA DEF TCP IP
21. connected to the network and it is hard to find a desired ezTCP from the LIST box this button may be conveniently used After changing the settings save the changes to ez TCP CIE H10 will automatically reset after the save Therefore pressing this button may cause system shutdown during normal use CIE H10 provides user authentication function in order to prevent other people from changing its settings The authentication process is done using a password and this button will allow users to change the password If the password for the ezManager 19 already designated the program will ask the user to input password as the button is clicked The designated password will also be used when connected to the web HTTP The ID is admin User can check the status values of CIE H10 during its operation When the button is clicked a new window will pop up and show operation time current IP address data amount via serial port and other information Clicking each devices of the Search List will also yield the same information This will be used to read debugging messages from CIE H10 In order to use this function activate Debug option under OPTION tab When the debugging is over please deactivate the Debug option to minimize network load When the PC s firewall 1s activated ezManager may not be operated properly By clicking this button the user can easily check their Windows firewall status A E 4 2 3 ezManager Set
22. d IP Address When this category is selected host connections can be restricted based on designated IP address and Net Mask setting values When Allowed IP Address is selected Allowed IP and Net Mask category may be bit AND to identify allowed hosts Ex E E Allowed IP Allowed Hosts 10 1 0 1 255 0 0 0 10 1 0 1 10 255 255 254 10 1 0 1 259 255 255 0 10 1 0 1 10 1 0 254 192 168 1 4 299 255 255 235 192 168 1 4 8 2 3 ezManager Lock When ezManager Lock is selected ezManager can only be used in hosts designated by Allowed Ethernet Address or Allowed IP Beware that 1f this category is selected changing device settings may become difficult 48 9 Debugging If user logs in the CIE H10 user can monitor CIE H10 status And if user sets the debugging option user can gets debugging data with ezManager 9 1 Telnet 9 1 1 Telnet Login If the Telnet parameter is set user can log in the CIE H10 User can monitor the status of the serial ports and the network If user inputs telnet CIE H10 IP Address T user can log in the CIE H10 with telnet Then the following message will be shown C Telnet 1 0 1 1 O 1 CSE H18 Management Console vi Sollae Systems HE K 9 1 2 Commands Network Status User can monitor network status of CIE H10 with the st net command c Telnet 10 1 0 1 lsh gt st net local address 1H 1 H 1 2335 1H 2 H 15654 1H395 193 ESTABLISHED
23. data byte count Byte Count or the duration of the data exceeds Guard Time the incoming data will be recognized as one block This block will be sent to UDP Timeout is in 1Oms Since UDP communication does not involve establishing connection N M communication may be performed using broadcast Therefore it can be conveniently in changing RS 485 multi drop type network to Ethernet Remote Host CIE H10 Serial Device EET ETE eoe AB In Cc DATA ABC UDP RE mmm EE EE BC er Oms ka ASS AT DATA BCA UDP lt U2S Transmission sequence Byte Count 3 Guard Time 1 gt 39 7 ATC Mode 7 1 Outline In ATC mode users can use AT commands to control and monitor CIE H10 For example AT PRIP command can be used to designated an IP address and ATD command to establish connection to that IP address Therefore multiple communications with different hosts can be established after one another Also ATA command allows users to perform manual connection 7 1 1 AT Command Form AT command starts with AT and ends with CR AT command form is as the following GED Response code for AT command 1s as the following Response lt CR gt 0x0d lt LF gt 0x0a lt CR gt 0x0d lt LF gt 0x0a Message Response message When it is ATV Initial Status CONNECT TCP Connection Established Detai
24. e esse ee ese ee ee ee ee ee ee ee ee ee nnns 3l S E CONECTO N EN N EE EE N EE EE ET 31 Das OA ON JO Deua eutanasia En aes ue sexes Ha A 32 6 SERIAL INTERFACE iios diit otii ores es ere d eeu Ce o be Gee ee deeg edv Ed de nn ei uda 33 6 1 SERIAL COMMUNICATION MODE sustos 33 6 2 E2S MODE od ld osas 34 02de CONCA c E 34 0 2 2 Serial Data before TOP CONE ED dene dicta testet luca eee 34 6 2 3 Dula COMMMMIC AION Si 34 0 245 CONNECTION Ea rT doses sida 35 6 3 COD T THT 36 6 3 1 Serial Data before Connection ii 36 052 Dala COMMUNICATION bo 36 63 Connechon Lerma tr sio SS ee f ae 37 6 4 dp oi 38 6 5 AM N OE T 39 de TC MODE niani laa iii 40 IAR OETEINE Mr 40 Dude AF COMMGNG BOE So susti E H boue audet Lois ee ED dee 40 12 BASIC AT COMMAND EX ATA ATD ETC ees esse ee ees ee ee ee ee ee ee ee ee ee ee nnn nnn nnn snis 40 7 3 EXPANDED AT COMMANDS EX AT PLIP ETC 4 7 4 ONLINE STATUS AND AT COMMAND STATUS 4 7 4 1 Method to change to AT Command Status from Online Status ee 42 7 4 2 Method to change to Online Status from AT Command Status 42 7 5 EXAMPLE FOR SETTINGS DONE BY AT COMMANDS eene eene 42 LOs EXAMPLE FOR CONNECTION un ESEG REGEER Re Tuto No hene PRU Y SEDE Oo Sha Be dee De ee pa RON SUME 42 OL sample or Active CONNECTION reren n itp eom usse debut an De DR oe 42 ho Evdmple for
25. e oett ers 13 Environmental F actor SED m e eaei 13 TSO CTA O O O LL Dee de 13 TESTOPERADION sie ivt desto UO esa Sx ee i ee ee Ds fune 14 A ESA E EL 14 CUPL O ANSI OMA O CE 4 OSATO 4 Modbus M EP Lest ea a cM tM I7 Test usi Web BIOWSER HELP oodd eo os l8 IP ADDRESS AND SETTING VALU ES eene eee eee eee see esse ee esse see see see esse esse esse 20 IP ADDRESS AND SETEIING VALUES vicende e oe ee ed roads 20 SETTINGS BY BZMANAGER cirio dnd 20 CLIN ONS ee T E came E E 20 eZ Manaser DUITOIS dssdo eto duse ROO Mt ant E SE Ee ei 2l SANO ULA DS A x seus oM M MM UR MIN MM GE ae eee 22 ez Manager Operation EXample itt ertet a ot eye e e eve eese fes 23 IP ADDRESS RELATED CATEGORIES SETTINGS VIA DHCP eee 24 4 4 IP ADDRESS SETTINGS VIA PPPOE eene ee ee ee ee ee n ee ee rese ee ee ee ee ee 24 4 5 DDNSADYNAMIC DASSE EG e ial 24 S MOINTE REA CR oe 26 ST MODBUS LCP bannen sene mas Saas GE bete ees 26 Jod Modbus EP Seme Values i ce tse nente ee ca a ea ee 27 ld MONA CADA 0 TT 28 Sed Modbus TCF Master Modest iaa E R 28 K PER CONMECHON MOE SE aa ates cotto tei b e tita SR ES 28 gd Initial Output Vale buie at ip e i p el ido 29 9 2 MACRO NODE T 29 Ids MIT EMM AE EA AA TR AE EN 29 dur A EE i cav LA AA N HE ED N OE N 30 3 2 95 RAMPA T ios 30 5 3 MONITOR AND CONTROL USING WEB HTTP e
26. ed via CIE H10 s output port and master s Input Port value will be sent via Write Multiple to the slave Using this function remote input port s value may be sent to slave s output port I O Tunneling Poll Interval Interval in between CIE H 10 s queries as master Unit ms Slave mode CIE H109 Unit ID Unit ID l l Master mode CIE H10 and remote device Unit ID Slave mode CIE H10 Input port address Input port Master mode Slave device Input port address Address Input port Address and Output port Address must differ by a number larger than 8 Slave mode Output port address Output port Master mode Slave Output port address Address Address and Output port Address must differ by a number larger than 8 CIE H10 establishes TCP connection passively When remote host connects to previously designated Port Passive CIE H10 will allow TCP connection In order to communicate using Modbus TCP this category must be selected CIE H10 establishes TCP connection to previously designated IP address Peer Address and Port Peer Address IP address when CIE H10 performs active connection Passive connection mode Local Port number that will receive m connection Active connection mode Peer Port number that will establish TCP connection As long as there is no query from the Master standard Modbus TCP will not send current status to the remote host When CIE H10 s input port value is changed while this category Inpu
27. est using Web Browser HTTP Start the web browser as shown below and write http and IP address in the address window to connect to the CIE H10 web browser It will allow users to monitor and control CIE H10 Click on the Read button to read input output values Designate output values on the CIE H10 s output port DOO DO and click Write button to apply setting values to the CIE H10 s output port Then the CIE H10 s input port value will be read as well 18 3 CIE H10 Microsoft Internet Explorer File Edit View Favorites Tools Help Q pack E N D E 5 pi Search SP Favorites Qi Media ES Address El http 10 1 0 ij CIE H10 INTERNET o o b Internet 19 4 IP Address and Setting Values 4 IP address and setting values In order to perform TCP IP communication the settings related to the IP address must be designated IP address and serial port related settings may be designated by the network set up utility provided by Sollae Systems ezManager 4 2 Settings by ezManager 4 2 1 ezManager The basic settings of CIE H10 IP address settings and serial port settings can be designated by an application utility for Windows ezManager ezManager can be operated in Windows platform Windows 98 98SE 2000 pro ME XP pro home but may malfunction in older OS versions The following window is the window that pops up when the user starts ezManager for the first time ezTCP Man
28. hat is to be AT PRP 1470 lt CR gt connected lt CR gt lt LF gt OK lt CR gt lt LF gt a Command process OK i ATDT lt CR gt K Connect to outer host command Attempt connection to outer host En lt CR gt lt LF gt CONNECT lt CR gt lt LF gt zz Successful TCP connection to outer host Data output input 7 6 2 Example for Passive Connection PO Ml D ampurun cm LOCAL PORT sering 4 lt CR gt lt LF gt OK lt CR gt lt LF gt Command process OK T ATA lt CR gt Wait for connection command Connection from outer host 4 lt CR gt lt LF gt CONNECT lt CR gt lt LF gt TCP Connection OK 7 Example for Connection Termination 7 7 1 Example for Active Connection Termination This is the connection termination process when CIE H10 actively terminates connection first gt J oa Data output input During TCP connection l l Convert to AT command status from online guard time guard time status TCP connection termination command TCP connection termination lt CR gt lt LF gt OK lt CR gt lt LF gt En lt CR gt lt LF gt OK lt CR gt lt LF gt Mi Conversion to AT command status complete 43 Fe Example for Passive Connection Termination When outer host attempts to terminate connection first CD oe J o0 59 Data output input During TCP connection Outer host attempts to terminate connection first lt CR gt lt LF gt NO CARRIER lt CR gt lt LF gt TCP connection termina
29. he correct IP address is designated If it reads Request timed out check to make sure correct IP address setting values C gt ping 10 1 0 1 Pinging 10 1 0 1 with 32 bytes of data Reply from 10 1 0 1 bytes 32 time 1ms TTL 64 Reply from 10 1 0 1 bytes 32 time 1ms TTL 64 Reply from 10 1 0 1 bytes 32 time 1ms TTL 64 Reply from 10 1 0 1 bytes 32 time 1ms TTL 64 When IP address is 10 1 0 1 gt N In order for the PING command to perform properly CLE H10 and PC s IP address subnet mask and gateway IP address must be adequately set for the network environment 4 3 IP Address Related Categories Settings via DHCP In the network environment composing DHCP server settings related to CIE H10 s IP address subnet mask gateway and name servers can be automatically designated using DHCP protocol In order to do so user must check DHCP category on ezManager Depending on DHCP server type ARP category should also be checked as well AA IP Address settings via PPPoE Usually PPPoE is used in ADSL or VDSL environment In order to use PPPoE PPPoE function must be activated and PPPoE s ID and password must be designated accordingly Like DHCP PPPoE automatically receives IP address V Some ADSL or VDSL environment uses DHCP based on the modem type Please contact your internet service for further information 4 5 DDNS Dynamic DNS E m In internet environment most host get IP addresses dynamically
30. ication counter part 2 3 4 Ethernet Interface Since part of CIE H10 network is composed of Ethernet UTP cable may be connected The 10 Ethernet portion will automatically sense 10Mbit and 100Mbit Ethernet and connect itself It also provides auto MDI MDIX function that can automatically sense 1 1 cable or cross over cable Each Ethernet device has its own unique hardware address The hardware address of CIE H10 is set in the factory before being shipped to the market The hardware address 1s also known as the MAC address 2 3 5 Power DCS5V is used for the power The specifications of the power plug are as the following EE 2 3 6 System LED CIE H10 has numerous lamps to show the current system status Each lamp shows the following status ME MF UN When the power is on Flicker with When the IP address is set as a fixed IP ls interval address or when the dynamic IP 1s allocated Flicker for 4 SIS Yellow times within When the dynamic IP address is not allocated or ISP mode When connected to 100 M network When there is data in LAN while being Flicker connected to 100 M network When connected to 10 M network When there is data in LAN while being Flicker connected to 10 M network DI Yellow On input ONGign signat to input port DO Green On Output ON signal from output port relay 2 3 7 ISP Switch There is an ISP switch located on the side of the product It i
31. ing on the network status Modbus TCP device may have to establish connection to the Manager In this special case CIE H10 can be changed into Active mode to actively connect to the remote host Standard Modbus TCP Passive Remote host connects to CIE H10 Port number that will receive connection must be designated CIE H10 connects to remote host Active IP address or host name and port number of the desired host must be designated 5 1 5 Initial Output Value Initial value for CIE H10 output port after booting may be designated Depending on the Initial State value during the boot output port will be activated 5 2 Macro Mode When users designated different macros for each output port CIE H10 can output various results via output port using input values and designated macros It is a mode that can be used to activate various devices based on signals from various Sensors Check Macro check box in ezManager to activate CIE H10 macro mode 5 2 1 Operator The algorithm used in the Macro mode is Boolean Algebra In this case the AND OR NOT are used as operators Parenthesis may also be used The priority of operators is in the following order parenthesis gt NOT gt AND gt OR Each operator is represented by the following symbols Since calculations within the parenthesis have the Parenthesis L highest priority they will be calculated first Parenthesis may be nested used Operand that follows NOT operator is toggled If
32. llowing DNI Since the input port is interfaced with a 5mm terminal block use a shaped screwdriver to connect 1t with the user device e Valid Time CIE H10 will only recognize input port signals that last for the Valid Time set by the user If the signal 1s not maintained during the designated Valid Time the input signal will be ignored The Valid Time is used for Modbus TCP Macro HTTP and other functions provided by CIE H10 The unit used for the Valid Time is lms However since the accuracy is only guaranteed in 10ms the designated values will round down in units of 10ms according to the designated values by the users 2 3 2 Output Port CIE H10 output port is interfaced via relay as shown below It is the part where the EXTERNAL OUTPUTI and EXTERNAL OUTPUT 2 are interfaced with the user device gt gt EXTERNAL OUTPUT1 e3 EXTERNAL OUTPUT2 VCC 5V FROM PROCESSOR 5 RELAY SPST The output port will perform the following actions of or The allowed electrical current based on voltage conditions of the output port are as the following Allowed Voltage l electrical Condition current ACI25V 10A Since the output port is interfaced with a 5mm terminal block use a shaped screwdriver to connect it with the user device O Delay CIE H10 will send output value to the output port after waiting for Delay ms In order to do so the signal value must last for Delay
33. ls NO CARRIER TCP Connection Termination ERROR Designated Query designated value Example Value AT PRIIP Designated Value 7 2 Basic AT Command Ex ATA ATD etc l l Wait for connection Host CIE HIO passive connection l Connection Decide whether to echo inputted letters E echo E0 not echo E1 echo 40 off hook Forced Connection Termination Output CIE H10 related information I Info ATI3 Firmware version ATI7 MAC address o Online Convert to Online from AT commands status enable result code Result code form Number VO Letter V 1 7 3 Expanded AT Commands Ex AT PLIP etc When values for this category 1s changed it local IP address must be saved with AT PWP command Cum em T Cae Tse Come emere me wma S C eras OR reremen ea Whether to use IP setting method using ARP DHCP ON 1 OFF 0 7 4 Online Status and AT Command Status When connection cannot be established in AT mode the device 19 in AT command mode In ON 1 OFF 0 AT command mode AT commands may be used When TCP connection is established the device is in online status In online status AT commands may not be used In order to use AT commands during TCP connection use ATO command to change into AT command status When TCP connection is not established AT commands may be AT Command Status used During TCP connection all of the data are converted to TCP IP Online Status for
34. mat 4 7 4 1 Method to change to AT Command Status from Online Status In order to change to AT command status from online status must be sent according to the below time format When sending is sent to the host From last sent data to first input More than 500ms Input interval 0 500ms Delay time after last input More than 500ms 7 4 2 Method to change to Online Status from AT Command Status When the device 1s changed to AT command status from online status during TCP connection ATO command may be used to change 1t back to online status 7 5 Example for Settings done by AT Commands Oe o TR gt LOCAL Padi ing OO EIE EEN command pr METEO D GATEWAY aime O EIE EE command ro EN REM Sassa PUNT MASK ees O IE oemeneesok arme D LOCAL PoRr sang O lt CR gt lt LF gt OK lt CR gt lt LF gt I Command process OK AT PTO 10 lt CR gt K TIME OUT setting lt CR gt lt LF gt OK lt CR gt lt LF gt Command process OK Save setting values to EEPROM Saved AT PWP lt CR gt even after reset lt CR gt lt LF gt OK lt CR gt lt LF gt Command process OK lt CR gt lt LF gt NO System reset CARRIER lt CR gt lt LF gt 7 6 Example for Connection 7 6 1 Example for Active Connection OT oe 42 Designate IP address that is to be AT PRIP 192 168 1 201 lt CR gt connected En lt CR gt lt LF gt OK lt CR gt lt LF gt a Command process OK Designate PORT number t
35. mmunication system via internet is rapidly increasing due to the development of internet through out the world In order to send and receive data via internet TCP IP protocol must be used Any machines that need an internet connection must implement TCP IP protocol In order for any device to implement TCP IP protocol the machine must either be able to implement TCP IP protocol by itself have an open TCP IP source implanted or must use an OS that is capable of implementing the protocol However the above options require a great deal of time cost and effort to make 1t work CIE H10 uses MODBUS TCP and HTTP to provide users with ability to control and monitor remote digital I O controllers Therefore with CIE H10 remote I O devices can easily be controlled and monitored at the same time Also CIE H10 provides the Macro functions to automatically change the output value via output port based on the input value from the input port Not only that CIE H10 can control and monitor digital I O controllers it also provides with functions that can covert the serial data to TCP IP data and vice versa Therefore one CIE H10 can perform numerous functions at the same time Along with its strong TCP IP UDP functions CIE H10 also provides DHCP and PPPoE functions to be used in cable and xDSL networks And 1t has DDNS Dynamic DNS function so 1t can be used more easily in the internet It is also equipped with online debugging functions that will allow the
36. nd oily environment Do not use the product in combustible or corrosive gas environment The product functions are not guaranteed in environments with too much noise Please do not use this product for special cases requiring special quality and reliability such as space raveling airplane medicine nuclear power transportation and other safety 255 devices If accidents or loss may occur using this product Sollae Systems will not be liable for any compensation 253 11 Revision History Jun 11 2007 Initial Release Jun 28 2007 Add Security Function Jun 29 2007 Jul 16 2007 Change English Expressions by JJS Correct Maximum Input Port Voltage Sep 03 2007 Add Telnet COM Port Control Option Sep 19 2007 Add DDNS Dynamic DNS 54
37. s a switch that will allow CIE H10 to perform in ISP mode If the switch is pressed more than 100ms or the power is turned on as the switch is pressed CIE H10 will be activated in ISP mode ss 3 Test Operation 3 1 Installation procedure CIE H10 can be installed with the following procedure Large category Small category IP address environment l m Confirm Modbus TCP HTTP Macro Communication l categories Serial port value Environment Confirm Application program De Confirm Check for LINK LED light Network Connection method 3 l Setup Method Network Setup utility ezManager Environmental factor setup 4 Confirm Check with ezManager or Web Test Operation method browser HTTP 5 Operation 3 1 1 Communication Environment Confirm Check IP address network environment serial port value protocols used in controlling digital I O devices and other application programs before installing CIE H10 3 1 2 Network Connection After connecting CIE H10 to the power directly connect it with PC s Ethernet port or connect it with the network hub that the PC is connected to When the LINK LED is on the network is established However since CIE H10 is only physically connected IP related values must be designated to perform ping test and IP communication 3 1 3 Environmental Factor Setup When network connection is established ezManager program will be used to perform setup via LAN 3 1 4 Test Operation
38. seconds If the output value does not last for the Delay seconds CIE H10 will not send that signal to the output port If the Delay value is set as 0 CIE H10 will send the output value to the output port immediately The Delay is used for Modbus TCP Macro HTTP and other functions provided by CIE H10 The unit used for the Delay is 1ms However since the accuracy is only guaranteed in 10ms the designated values will round down in units of 10ms according to the designated values by the users 2 3 3 RS232 Port DB9M CIE H10 has an RS232 port for user serial device CIE H10 converts serial data from user device to TCP IP and transmits to Ethernet port And CIE H10 convert TCP IP data from Ethernet port to user serial device and it transmits raw data to user device e Pin Assignment s ewo omms Tael Tet e os eana Tan inp oer a ets ciar sena 25232 input orien Ter Ring macs R282 ma onion O Data bits Parity and Stop bit Configurable Value None Even Odd e Flow Control CIE H10 support None and RTS CTS Hardware Flow Control O Telnet COM Port Control Option CIE H10 has Telnet COM Port Control Option function that is specified by RFC2217 If the Telnet COM Port Control Option is enabled CIE H10 sends the CTS DSR control signal to the communication counter part and CIE H10 sets its serial port items RTS DTR Baudrate databits parity stop bit after getting information from the commun
39. t Change l m l l l is selected it will send Read Multiple response packet to the Notification l n Master without receiving queries from the Master This function may be used to quickly send CIE H10 s Input Port status Output port value when CIE H10 is booted 5 1 2 Standard Modbus TCP standard Modbus TCP will allow users to use Modbus TCP Manager to control and monitor devices that supports Modbus TCP In order to operate in standard Modbus TCP select Modbus TCP mode as Slave mode change TCP connection as Passive and set TCP port number as 502 Also adequate CIE H10 s Unit ID Input port address and Output port address must be selected In the case of CIE H10 Input port Address and Output port Address must differ by a number larger than 8 5 1 3 Modbus TCP Master Mode CIE H10 operates as Modbus TCP Master and reads input port values off of remote Modbus TCP Slave and uses those values in CIE H10 output port Then CIE H10 sends its input port value to remote slave device as Write Multiple Function Code When connecting to Modbus TCP device the TCP connection must be in Active setting Using this function CIE H10 input values can be sent to the remote slave device and remote slave input port values may be outputted by CIE H10 s output port 5 1 4 TCP Connection Mode Standard Modbus TCP allows user Manger to establish TCP connection to Modbus TCP device s 502 port 28 However depend
40. tings NETWORK Network Local IP CIE H10 s IP address Address Subnet Mask Subnet Mast Gateway IP Gateway s IP address Address DNS IP Name Server s IP address Address Option DHCP Decide whether to receive CIE H10 IP address via DHCP PPPOE Decide whether to receive CIE H10 IP address via PPPoE PPPoE ID ID and Password that will be used in PPPoE amp Password ARP ARP Function activation status Conditionally required for DHCP Obtain DNS If CIE H10 s IP address is set as a dynamic IP DHCP or PPPoE it server will automatically receive DNS server address If this check box is address not activated the IP address designated in the DNS IP Address will automatically be used as the DNS server address DDNS Service Set a DDNS service provider Provider CIE H10 supports only Dyndns www dyndns com The user account which was registered to the service provider User The password of user account which was registered to the service Password provider The hostname of CIE H10 Host Name l For example cieh10 dyndns com OPTION Remote Use IP address to check for device settings in the ezManager s Search REMOTE tab Enable telnet login E Used for CIE H10 online debugging Allows users to make comments about the products Allowed Ethernet Address Only allow hosts with Ethernet Address designated in ezManager s Allowed Ethernet Address to be connected to CIE H10 Allowed IP Only allow hosts with I
41. tion 44 8 Security Function CIE H10 provides users with password MAC address access restriction IP address restriction and other security functions 8 1 Password When password for CIE H10 is designated password is required when users are attempting to change CIE H10 settings Also when connecting to CIE H10 via web browser to monitor and control input output port users must insert the designated password 8 1 1 Set and Delete Password Password for CIE H10 can be designated in ezManager Click Change PWD button in ezManager and enter desired password in the window Enter current password in the Current window and click OK after checking the delete check box to delete currently designated password Change Password E Lurrent ok NEM RETYPE delete NEW Enter new password Current window to delete current password When there is currently designated password enter current password Current BEEN in this window 8 1 2 CIE HIO settings with Designated Password In order to save environmental factor values to CIE H10 that has designated password enter password in the window next to Change PWD and click Save 45 ez CP Manager v1 29 22 May 2007 MAC Address e2TCP Mode A Jl TESCO TCP Server 20 19 00 00 06 Local Port 1470 Peer Address Peer Port p Timeout Byte Count EE EEN Guard TimetiUms lali HE FIBI HAAI 8 1
42. will accept TCP connection When CIE H10 accepts the connection TCP connection is established After establishing connection data that comes through serial port will be sent to the remote host after TCP IP process and TCP IP data that comes from the remote host will be sent to the serial port after TCP IP process to establish data communication Remote Host CIE H10 Serial Device Listen on local port Request TCP connection Accept TCP connection 2 connected DATA ABC DATA ABC TCP IF DATA DEF TCP IP DATA DEF T2S Mode 6 2 1 Connection When remote host connects to previously designated CIE H10 user devices that are connected to CIE H10 can establish full duplex data communication with remote host 6 2 2 Serial Data before TCP Connection Data before TCP connection will be handled based on the Byte Count settings If the Byte Count is 0 the data that comes to CIE H10 s serial port will not be recognized If it is not 0 the serial data before TCP connection will be temporarily saved to be sent to the host after the connection 6 2 3 Data Communication When the TCP connection is established the data communication in between the host and the serial device will be established Then CIE H10 will send data according to the Guard Time In other words when the data comes through CIE H10 s serial port it ss will be temporarily saved in the
Download Pdf Manuals
Related Search