K3HB-P - Mouser Electronics
Contents
1. I O signal name REQUEST Input signal No voltage HOLD contact input MAX Input current for no voltage input 10 mA ee Signal level ON voltage 1 5 V max OFF voltage 3 V min DATA Maximum load voltage 24 VDC POLARITY OVER Maximum load current 10 mA DATA VALID RUN Leakage current 100 uA max Maximum load voltage 24 VDC Maximum load current 50 mA Leakage current 100 uA max Refer to the K3HB Communications User s Manual Cat No N129 for details on serial and DeviceNet communications omRONn K3HB P DeviceNet Communications Communications protocol Conforms to DeviceNet Supported Remote I O communications communications Master Slave connection polling bit strobe COS cyclic Conforms to DeviceNet communications standards I O allocations Allocate any I O data using the Configurator Allocate any data such as DeviceNet specific parameters and variable area for Digital Indicators Input area 2 blocks 60 words max Output area 1 block 29 words max The first word in the area is always allocated for the Output Execution Enabled Flags Message communications Explicit message communications CompoWay F communications commands can be executed using explicit message communications Connection methods Combination of multi drop and T branch connections for trunk and drop lines2. Baud rate DeviceNet 500 250 or 125 Kbps automatic follow up Communications media Communications distance Special 5 wire cable 2 signal lines 2 power supply lines 1 shield line Baud rate Network length Drop line length _ Total drop line length max max max 100 m max 39 m max 100 m max 100 m max 250 m max 100 m max 500 m max 78 m max 156 m max The values in parentheses are for Thick Cable Communications power supply 24 VDC DeviceNet power supply Allowable voltage fluctuation range 11 to 25 VDC DeviceNet power supply Current consumption 50 mA max 24 VDC Maximum number of nodes 64 DeviceNet Configurator is counted as one node when connected Maximum number of slaves Error control checks 63 CRC errors DeviceNet power supply Supplied from DeviceNet communications connector omRONn K3HB P Connections E External Connection Diagrams Terminal Arrangements Note Refer to Internal Block Diagram on page 10 for information on isolation A Operating Power Supply 100 to 240 VAC 24 VAC VDC gt p 8 Check the required power supply type Relay Outputs Relay Outputs Transistor Outputs DeviceNet Connector Included lt C1 gt lt C2 gt lt T1 gt lt T2 gt lt DRT gt HH C HH C H _A H com C pass C L L 1 V Power supply ca
3. output or DeviceNet communications 3 Relay Transistor Output Type Code None None C1 Relay contact H L SPDT each C2 Relay contact HH H LL L SPST NO each T1 Transistor NPN open collector HH H PASS L LL T2 Transistor PNP open collector HH H PASS L LL BCD BCD output transistor output NPN open collector HH H PASS L LL DRT DeviceNet See note 2 A Special BCD Output Cable sold separately is required 4 Event Input Type Code None None 5 inputs HOLD RESET NPN open collector 8 inputs HOLD RESET BANK1 BANK2 BANK4 NPN open collector 5 inputs HOLD RESET PNP open collector 8 inputs HOLD RESET BANK1 BANK2 BANK4 PNP open collector PONS omRONn K3HB P Accessories Sold Separately K32 DICN Special Cable for event inputs with 8 pin connector K32 BCD Special BCD Output Cable Watertight Cover Rubber Packing Model o O Ooo Model Note Rubber packing is provided with the Controller Specifications Ratings Supply voltage 100 to 240 VAC 24 VAC VDC DeviceNet power supply 24 VDC Allowable power supply voltage 85 to 110 of the rated power supply voltage DeviceNet power supply 11 to 25 VDC range Power consumption 100 to 240 VAC 18 VA max max load See note 1 24 VAC DC 11 VA 7 W max max load Current consumption DeviceNet power supply 50 mA max 24 VDC Input No voltage contact voltage pulse open collector External power supply 1
4. 000 m max Accessories Watertight packing 2 fixtures terminal cover unit stickers instruction manual DeviceNet models also include a De viceNet connector Hirose HR31 5 08P 5SC 01 and crimp terminals Hirose HR31 SC 121 See note 3 Note 1 DC power supply models require a control power supply capacity of approximately 1 A per Unit when power is turned ON Particular attention is required when using two or more DC power supply models The OMRON S8VS series DC Power Supply Unit is recommended 2 PNP input types are also available 3 For K3HB series DeviceNet models use only the DeviceNet Connector included with the product The crimp terminals provided are for Thin Cables omRON E Characteristics Display range K3HB P 19 999 to 99 999 Measurement accuracy at 23 5 C 0 08 rgd 1 digit for voltage pulse open collector sensors Measurement range Functions F1 F3 and F4 Interval between input pulses 10 ms to 3 200 s Function F2 Interval between input pulses 20 ms to 3 200 s Functions F5 F6 Number of input pulses 0 to 4 gigacounts Input signals e Contact input dry contact input 30 Hz max with ON OFF pulse width of 15 ms min i No contact Mode Inputfrequency ON OFF ON voltage OFF voltage Input ge pulse z range pulse width impedance F1 to F4 0 to 50 kHz 9 us min 4 5to30V 30to2V 10 kQ F5 F6 0 to 30 kHz 16 us min Mode Input freque
5. 2 VDC 10 80 mA for models with external power supplies only Event inputs Hold input NPN open collector or no voltage contact signal See note 2 Reset input ON residual voltage 2 V max ON current at 0 Q 4 mA max Bank input Max applied voltage 30 VDC max OFF leakage current 0 1 mA max Output ratings Relay output 250 VAC 30 VDC 5 A resistive load Mechanical life expectancy 5 000 000 operations Electrical life expectancy 100 000 operations Transistor output Maximum load voltage 24 VDC Maximum load current 50 mA Leakage current 100 uA max Linear output Linear output 0 to 20 mA DC 4 to 20 mA DC Load 500 Q max Resolution Approx 10 000 Output error 0 5 FS Linear output 0 to 5 VDC 1 to 5 VDC 0 to 10 VDC Load 5 kQ max Resolution Approx 10 000 Output error 0 5 FS 1 V or less 0 15 V no output for 0 V or less Display method Negative LCD backlit LED display 7 segment digital display Character height PV 14 2 mm green red SV 4 9 mm green Main functions Scaling function measurement operation selection output hysteresis output OFF delay output test teaching dis play value selection display color selection key protection bank selection display refresh period maximum mini mum hold reset Ambient operating temperature 10 to 55 C with no icing or condensation Ambient operating humidity 25 to 85 Storage temperature 25 to 65 C with no icing or condensation Altitude 2
6. Comparative results other than PASS can be output from the PASS output terminal Output OFF Delay oFF d Delays turning OFF comparatives for a set period This can be used to provide sufficient time to read the comparative output ON status when the comparative result changes at short intervals snot Output EE Turns ON the comparative output for a specific time Output Logic tt n Reverses the output logic of comparative results Output Test EESE Output operation can be checked without using actual input signals by using the keys to set a test measurement value C i i EE SEEH L5EEL A current or voltage proportional to the change in the measurement value can be output StdbY The comparison outputs can be kept OFF until the measurement value enters the PASS range Standby Sequence omrRONn Display Display Value Selection IAB 5P The display value can be set to the present value the maximum value or the minimum value EWA elm OL Or The present value display color can be set to green or red The color of the present value can also be switched according to the comparative output Display Refresh Period d EF When the input changes rapidly the display refresh period can be lengthened to control flickering and make the display easier to read Position Meter PoS t PaS H PaS t The present measurement value can be displayed as a position in relation to the scaling width on a 20 gradation pos
7. H H In RUN level turn ON when the lcomparative set value HH H L or LL L LL __ is displayed MAX MIN Key LEVEL Key MODE Key SHIFT Key UP Key Used to switch the Used to switch level display between the PV maximum value and minimum value and to reset the maximum and minimum values Used to switch the parameters displayed Used to change parameter settings When changing a set value this key is used to move along the digits When changing a set value this key is used to change the actual value When a measurement value is displayed this key is used to execute or clear the forced zero function or to execute teaching omrRON E Dimensions Om py aoga Character Size for Main Display mm K3HB P Panel Cutout Dimensions PV display SV display 120 min 2 a oy 4 n as 7 6 75 min 92 98 aa ee 2 Leave a distance of at least 140 mm when using the Watertight Cover Y92A 49N Note Mounting Recommended Panel Thickness 1 to 8 mm Mount the product horizontally k1 DeviceNet models 97 mm Terminal M3 Terminal Cover Accessory Wiring Precautions e For terminal blocks use the crimp terminals suitable for M3 screws e Tighten the t
8. Model e NPN input section 12V E2 E5 PEE 5109 VY 4 W i K 7009 COM th Connectable Sensors K3HB P PNP Input Model E3 E6 COM ON residual voltage 3 V OFF leakage current 1 5 mA max e Voltage pulse input section Note A 2 wire DC sensor can also be connected Check the ratings and characteristics tables however for the connection conditions Note E3 and E6 as well as B6 are internally connected Models with Connectors Note E3 and E6 as well as B5 are internally connected E3 E6 ON voltage 4 5 to 30 V Connectable Sensors OFF voltage 30 to 2 V e Use terminal pin D6 as the common terminal Models with Terminal Blocks e Use NPN open collector or no voltage contacts lt 1 gt lt 3 gt lt 2 gt lt 4 gt for event input 1 N C 2 2 N C PNP types are also available 3 HOLD lanl 4 RESET T E 12V 5 N C aal 6 COM Y 7 BANK4 Pe 10 8 BANK2 TO g 1 9 BANK1 28 19 10 COM eT ps RESET D4 arog yell y e Applicable Connector Sold separately N XG4M 1030 OMRON j AN e Special Cable Sold separately 3 9 kQ K32 DICN OMRON k XG4M 1030 with 3 m cable E 66 con 7 BCD Output Cable K32 BCD Connected device end PLC display device etc aa OVER DATA VALID RUN COMMON REQUEST MAX REQ MIN REQ ar HOLD L RESET POLARITY 46 5 mm HH D sub connector 37 pin fem
9. RUN HH H PASS L and i 3 LL are always output with or l without a REQUEST signal DATA Do not used a wired OR VALID See note See note See note connect for these signals Note Leave 20 ms min between DATA VALID turning OFF and the REQUEST signal Display Unit Connection Example Digital Indicator Programmable Controller Connection Example SYSMAC Programmable Controller DC Input Unit Digital Indicator Connector pin No See note Connector pin No See note 1 1 COMMON COM 1 1 COMMON h i h 24 IND ny 2 1 oS las IND wy A 3 2 ORY Jaa o Nh lt AH 5 8 Di a 5 k i e i i I I I _ 23 DATA VALID i 4 24 RUN IND sm SY Aa ial ie T10 1 amp 7 To 102 25 COMMON h Short pin d26 REQUEST 26 REQUEST circuit 5V 240 Q re z 5V 240 Q a i 8 g 240 Q S E i 30 RESET 30 RESET l e 540 2 2 H 2400 3 31 POLARITY E E 31 POLARITY onomea gt COOm lt A ly onoma U gt 240 i we m k polarity 2800 polarity a a o SEC L M7E 01DON2 01HON2 Sipa v lt M7E Digital Display Unit gt DC power Note The BCD output connector pin number is the D sub connector pin number when Oov supply the BCD Output Cable sold separately is connected This number d
10. Timer Interval Indicator K3HB P Digital Time Interval Meter for Measuring Passing Speed Time or Cycle between Two Points e Visual confirmation of judgement results through display colors that switch between red and green 1 e Measures Wide Range of Pulse Interval Times Measures calculates and displays pulse intervals between two points Wide range for pulse interval measurements from 10 ms to 3 200 s max e Six Measurement Operations Including Passing Speed Time and Cycle Measurement between Two Points One Digital Time Interval Meter has six measurement functions to support a variety of pulse interval measurement applications Select the best function for your application from the following Passing speed cycle time difference time band measuring length and interval e DeviceNet models added to the series 2 1 Visual confirmation of judgement results is not supported on models that do not have an output or models that do not support DeviceNet You can change the display color by setting it but you cannot switch it based on the judgement results 2 DeviceNet models have a depth of 97 mm CSM_K3HB P_DS_E_15_1 w ce For the most recent information on models that have been certified for safety standards refer to your OMRON website Refer to Safety Precautions for All Digital Panel Meters Model Number Structure E Model Number Legend Base Units and Optional Boards can be ordered in
11. ale Mag Cover 17JE 37H 1A manufactured by DDK L Connector Equivalent to 17JE 13370 02 LL manufactured by DDK COMMON 17L 002A manufactured by DDK 9 COMMON K3HB end 300 mm ig 38 mm HDR E50LPA5 manufactured by Honda Tsushin Co Ltd Connector HDR E50MAG1 manufactured by Honda Tsushin Co Ltd Cover Stud Note The BCD Output Cable has a D sub plug Cover 17JE 37H 1A manufactured by DDK Connector equivalent to 17JE 23370 02 D1 manufactured by DDK Special Cable for Event Inputs with 8 pin Connector Appearance K32 DICN Signal name N C S TMR HOLD RESET N C COM BANK4 BANK2 BANK1 COM 2 3 000 mm 3m Cable marking olojn oja A oN oO omrRONn K3HB P E Derating Curve for Sensor Power Supply Reference Values For 12V 140 120 100 Maximum current mA 80 60 40 20 20 10 0 10 20 30 40 50 6 amp 0 Ambient temperature C Note 1 The above values were obtained under test conditions with the standard mounting The derating curve will vary with the mounting conditions so be sure to adjust accordingly Internal components may be deteriorated or damaged Do not use the Digital Indicator outside of the derating range i e do not use it in the area labeled above E Interna
12. ance 150 m s 100 m s for relay outputs 3 times each in 3 axes 6 directions Weight Approx 300 g Base Unit only Degree of Front panel Conforms to NEMA 4X for indoor use equivalent to IP66 protection Rear case IP20 Terminals IPOO finger protection VDE0106 100 Memory protection Applicable standards EEPROM non volatile memory Number of rewrites 100 000 UL61010 1 CSA C22 2 No 61010 1 04 EN61010 1 IEC61010 1 Pollution degree 2 Overvoltage category II EN61326 1 EMC EMI EN61326 industrial applications Electromagnetic radiation interference CISPR 11 Group 1 Class A Terminal interference voltage CISPR 11 Group 1 Class A EMS EN61326 industrial applications Electrostatic Discharge Immunity EN61000 4 2 4 kV contact 8 kV in air Radiated Electromagnetic Field Immunity EN61000 4 3 10 V m sine wave amplitude modulation 80 MHz to 1 GHz 1 4GHz to 2 GHz Electrical Fast Transient Burst Noise Immunity EN61000 4 4 2 kV power line 1 kV I O signal line Surge Immunity EN61000 4 5 1 kV with line power line 2 kV with ground power line Conducted Disturbance Immunity EN61000 4 6 3 V 0 15 to 80 MHz Power Frequency Magnetic Immunity EN61000 4 8 30 A m 50 Hz continuous time Voltage Dips and Interruptions Immunity EN61000 4 11 0 5 cycle 0 180 100 rated voltage omrRONn K3HB P Operation E Functions Operating Modes F1 to F6 These functio
13. ble Black LL C3 LL 2 CAN L Communications cable Blue 3 Shield COM C COM C 4 CANH Communications cable White 5 V Power supply cable Red Applicable Connector HR31 5 08P 5SC 01 HIROSE ELECTRIC CO LTD Attach the provided crimp terminals BCD NPN Open Collector lt BCD gt Special Cable Sold separately K32 BCD OMRON HDR E50MAG1 with 0 3 m cable 0 5 1 5 0 10 V N C REQUEST MAX REQ 12 VDC 80 mA lt L2A gt lt L1A gt 10 10 24 2484248 Sensor power supply The BCD COMMON is shared The pins indicated in the above diagram as blank white boxes have been removed COMMON Only one of the following can be used for each Digital Indicator communications BCD or DeviceNet Contact Outputs Transistor Outputs NPN Open Collector HH B SD Eg A RD LL B SG PASS A N C 12 VDC 12 VDC 80 mA 80 mA Safety Standards Conformance RS 485 RS 232C eae lt FLK3A gt lt FLK1A gt e Always use a EN IEC compliant power supply with reinforced insulation or double insulation for the DeviceNet power supply e The product must be used indoors for the above applicable standards to apply omRONn Timer Interval Meter KSHB P NPN Input PNP Input K3HB LINB K3HB LIPB Input A Ecom Input B g PNP Ecom NPN Input
14. circuits system assemblies or any other materials or substances or environments Any advice recommendations or information given orally or in writing are not to be construed as an amendment or addition to the above warranty See http www omron com global or contact your Omron representative for published information Limitation on Liability Etc OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS WHETHER SUCH CLAIM IS BASED IN CONTRACT WARRANTY NEGLIGENCE OR STRICT LIABILITY Further in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted Suitability of Use Omron Companies shall not be responsible for conformity with any standards codes or regulations which apply to the combination of the Product in the Buyer s application or use of the Product At Buyer s request Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product machine system or other application or use Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer s application product or system Buy
15. covery time TR of 20 ms is required before starting the next measurement Display unit mm cm m etc F6 Interval Displays the number of input A pulses from when input B turns ON until input B turns ON again Measurement is made every other time input B turns ON Display value D C x a C Pulse value a Prescaling value 1234 1234 12 1 Input A mots TLL ea TR TR lt gt L HOLD input LOCO UOS S 1 Displa il 3 4 e Recovery time TR of 20 ms is required before starting the next measurement Display unit mm cm m etc E What Is Prescaling Measuring workpiece length BCD To Programmable Controller Measuring slit intervals H 2 31 4 21 14 2 INA i Tr i 1 Tr i i ier LLP NB Po E E E E Display I I 3 i 2 I To make calculations using the input pulse to display the passing speed between two points the distance between the two points and the display unit must be set and the internally measured time multiplied by a certain coefficient This coefficient is called the prescale value For information on settings details refer to the User s Manual Time Unit Settings Setting Meaning Seconds display when prescaling 1 0000 Minutes display when prescaling 1 0000 h mm ss display mm ss d display d tenths of a second Input Type Setting __ NO Voltage pulse high NC Voltage pulse low No con
16. dividually or as sets Base Units Base Units with Optional Boards K3HB P O K3HB PO O00 1 5 1 234 5 1 Input Sensor Code 2 Sensor Power Supply Output Type Code NB NPN input voltage pulse input None None PB PNP input CPA Relay output PASS SPDT Sensor power supply 5 Supply Voltage 100 240 VAC 100 to 240 VAC 24 VAC VDC 24 VAC VDC Optional Board Sensor Power Supply Output Boards K33 L 2 Relay Transistor Output Boards K34 3 Event Input Boards K35 a Note The following combinations are not possible e Communications FLKLIA DeviceNet DRT e Communications FLKLIA BCD output BCD e Linear current voltage LLA DeviceNet DRT 12 VDC 10 80 mA See note 1 L1A Linear current output 0 to 20 or 4 to 20 mA DC Sensor power supply 12 VDC 10 80 mA See note 2 L2A Linear voltage output 0 to 5 1 to 5 or 0 to 10 VDC Sensor power supply 12 VDC 10 80 mA See note 2 A Sensor power supply 12 VDC 10 80 mA FLK1A Communications RS 232C Sensor power supply 12 VDC 10 80 mA See note 2 FLK3A Communications RS 485 Sensor power supply 12 VDC 10 80 mA See note 2 Note 1 CPA can be combined with relay outputs only 2 Only one of the following can be used by each Digital Indicator RS 232C RS 485 communications a linear
17. er shall take application responsibility in all cases NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS AND THAT THE OMRON PRODUCT S IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM Programmable Products Omron Companies shall not be responsible for the user s programming of a programmable Product or any consequence thereof Performance Data Data presented in Omron Company websites catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty It may represent the result of Omron s test conditions and the user must correlate it to actual application requirements Actual performance is subject to the Omron s Warranty and Limitations of Liability Change in Specifications Product specifications and accessories may be changed at any time based on improvements and other reasons It is our practice to change part numbers when published ratings or features are changed or when significant construction changes are made However some specifications of the Product may be changed without any notice When in doubt special part numbers may be assigned to fix or establish key specifications for your application Please consult with your Omron s representative at any time to confirm actual specif
18. erminal screws to the recommended tightening torque of approx 0 5 N m To prevent inductive noise separate the wiring for signal lines from that for power lines Wiring e Use the crimp terminals suitable for M3 screws shown below 4 5 8 mm max t t L Omn t Unit Stickers included No unit stickers are attached to the Digital Indicator e Select the appropriate units from the unit sticker sheets provided B Fela min mm Note For measurements for commercial purposes be sure to use the unit required by any applicable laws or regulations Watertight Cover Y92A 49N Rubber Packing K32 P1 Ta gt Mounting Method 1 Insert the K3HB into the mounting cutout in the panel 2 Insert watertight packing around the Unit to make the mounting watertight Watertight packing SSSSSIS ASS HH SSS SSS SSS SUNNY SUS HOU SSS SSN 3 Insert the adapter into the grooves on the left and right sides of the rear case and push until it reaches the panel and is fixed in place Adaptor KSSS SSS LCD Field of Vision The K3HB is designed to have the best visibility at the angles shown in the following diagram 30 If the rubber packing is lost or damaged it can be ordered using the following model number K32 P1 Depending on the operating environment deterioration contraction
19. ications of purchased Product Errors and Omissions Information presented by Omron Companies has been checked and is believed to be accurate however no responsibility is assumed for clerical typographical or proofreading errors or omissions 2014 11 In the interest of product improvement specifications are subject to change without notice OMRON Corporation Industrial Automation Company http www ia omron cony c Copyright OMRON Corporation 2014 All Right Reserved Mouser Electronics Authorized Distributor Click to View Pricing Inventory Delivery amp Lifecycle Information Omron K3HB PPB 100 240VAC K3HB PNB 24VAC VDG K3HB PNB 100 240VAC K3HB PPB 24VAC VDC
20. iffers from the pin number for the Digital Indicator narrow pitch connector manufactured by Honda Tsushin Kogyo Co Ltd Refer to the following User s Manual for application precautions and other information required when using the Digital Indicator l I K3HB R P C Digital Indicator User s Manual Cat No N136 l l The manual can be downloaded from the following site in PDF format OMRON Industrial Web http www fa omron co jp l omRON E Component Names and Functions K3HB P Max Min status indicator Turns ON when the maximum value or minimum value is displayed in the RUN level Level bank display In RUN level displays the bank if the bank function is ON Turns OFF if the bank function is OFF In other levels displays the current level Comparative output status indicators PV display Displays PVs maximum values minimum values parameter names and error names Position meter Displays the position of the PV with respect to a desired scale SV display Display the status of comparative outputs Displays SV and monitor values Status indicators Display Lit when communications writing is ON enabled and not lit when OFF prohibited Turns ON OFF when hold input turns ON OFF SV display status indicators H
21. ition meter Ge S 90 PS AY PS bo PS bY The input signal can be converted and displayed as any value AEE Sud 5P Select whether or not to display the comparative value during operation Display auto return rEt Automatically returns the display to RUN level when there are no key operations e g max min switching bank settings using keys K3HB P Other Max Min Hold Holds the maximum and minimum measurement values baH E Switch between 8 comparative value banks using the keys on the front panel or external inputs A set of set comparative values can be selected as a group Bank Copy CoPY Any bank settings can be copied to all banks Bank Selection ALL DIMENSIONS SHOWN ARE IN MILLIMETERS To convert millimeters into inches multiply by 0 03937 To convert grams into ounces multiply by 0 03527 In the interest of product improvement specifications are subject to change without notice omrRON Terms and Conditions Agreement Read and understand this catalog Please read and understand this catalog before purchasing the products Please consult your OMRON representative if you have any questions or comments Warranties a Exclusive Warranty Omron s exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron or such other period expressed in writing by Omron Omron disclaims a
22. l Block Diagram Micro computer Sensor power supply 0 r Communi cations Communications driver Power supply omrRONn K3HB P E BCD Output Timing Chart A REQUEST signal from a Programmable Controller or other external device is required to read BCD data Single Sampling Data Output Continuous Data Output cs a a 20 ms pulse min 60 ms max REQ REQ MAX MIN MAX MIN DATA All data High DATA All data High All data High DATA DATA VALID VALID rer L a Approx 30 ms i a Approx s a ls gt 30 ms 40 ms 16 ms as 64 ms The data is set in approximately 30 ms from the rising edge of the REQUEST signal and the DATA VALID signal is output When reading the data from a Programmable Controller start reading the data when the DATA VALID signal turns ON The DATA VALID signal will turn OFF 40 ms later and the data will turn OFF 16 ms after that Measurement data is output every 64 ms while the REQUEST signal remains ON Note If HOLD is executed when switching between data 1 and data 2 either data 1 or data 2 is output depending on the timing of the hold signal The data will not go LOW e The K3HB BCD output model has an open collector output so wired OR connection is possible Programmable Controller DATA including POL and OVER and DATA VALID can be used in a wired OR DATA Cm X XOX XO K3HB
23. ll other warranties express or implied b Limitations OMRON MAKES NO WARRANTY OR REPRESENTATION EXPRESS OR IMPLIED ABOUT NON INFRINGEMENT MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right c Buyer Remedy Omron s sole obligation hereunder shall be at Omron s election to i replace in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof the non complying Product ii repair the non complying Product or iii repay or credit Buyer an amount equal to the purchase price of the non complying Product provided that in no event shall Omron be responsible for warranty repair indemnity or any other claims or expenses regarding the Products unless Omron s analysis confirms that the Products were properly handled stored installed and maintained and not subject to contamination abuse misuse or inappropriate modification Return of any Products by Buyer must be approved in writing by Omron before shipment Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components
24. ncy ON OFF Note The Digital Time Interval Meter range pulse width will malfunction if a pulse greater than the input frequency range is F1 to F4 0 to 50 kHz 9 us min input SYSERR may appear on F5 F6 O to 30 kHz 16 us min the display e Open collector Connectable sensors ON residual voltage 3 V max OFF leakage current 1 5 mA max Load current Must have a switching capacity of 20 mA or higher Must be able to properly switch load currents of 5 mA or less Comparative output response time transistor output 2 ms max time until the comparative output is made when there is a forced sudden change in the input signal from 15 to 95 or 95 to 15 Linear output response time 10 ms max time until the final analog output value is reached when there is a forced sudden change in the input signal from 15 to 95 or 95 to 15 Insulation resistance 20 MQ min at 500 VDC Dielectric strength 2 300 VAC for 1 min between external terminals and case Noise immunity 100 to 240 VAC models 1 500 V at power supply terminals in normal or common mode waveform with 1 ns rising edge and pulse width of 1 us 100 ns 24 VAC VDC models 1 500 V at power supply terminals in normal or common mode waveform with 1 ns rising edge and pulse width of 1 us 100 ns Vibration resistance Frequency 10 to 55 Hz Acceleration 50 m s 10 sweeps of 5 min each in X Y and Z directions Shock resist
25. ns use the internal system clock to measure the time between pulses or the pulse ON time and then display time measurements or a variety of other calculations Example F1 Passing Speed The time T between input A pulse and input B pulse 5 7 is measured by the internal system clock If for Function name Function No example the system clock measures 100 000 counts Passing speed during time T then meth T 1 system clock count 0 5 us x 100 000 Cycle Time difference eae l T 0 05s ops i l F1 the passing speed is calculated internally Time band l d r R using the formula 7 Xx 60 m min and the Measuring length Internal F PEER 1 Z Interval eak LIII MUIDU IDII display in this example would be T055 60 1 1 1200 m min Function Operation Operation image application F1 The reciprocal of the time T from input A ON to input Measuring workpiece passing speed between A and B Passing B ON is multiplied by 60 and displayed speed Display value D 1 T x 60 x a a Prescaling value Display e Recovery time TR of 20 ms is required before starting the next measurement Display unit mm s m s m min km h etc Measures and displays input A cycle T Measuring feed cycles for parts Display value D T x a a Prescaling value Input A ET Tae Ts Taa Ts 1 l i HOLD input T Te Ts I l I Display Measurement range 20 ms t
26. o 3 200 s Display unit ms s min min s 1 10 s F3 Displays the time T from input A ON to input B ON Measuring workpiece passing time Measuring the length of a Time dif Display value D T x a Prescaling value between A and B workpiece step by changing ference prescale values mua TAL A Input B l l f ke gt a gt i la ite TR faa ter h mE Tak ms g l l HOLD input i l l Display l l l T T Measurement range 10 ms to 3 200 s e Recovery time TR of 20 ms is required before starting the next measurement Display unit ms s min min s 1 10 s omrRONn Function F4 Time band Operation Displays input A ON time T Display value D T x a a Prescaling value Input A eT aan Tet Th 1 Tr I HOLD fe TL ns s aT j l i I ji Display izi T Measurement range 10 ms to 3 200 s e Recovery time TR of 20 ms is required before starting the next measurement Display unit ms s min min s 1 10 s K3HB P Operation image application Monitoring the ON time of a printing press Managing the valve release time Communications output F5 Measuring length Displays the number of input A pulses while input B is ON Display value D C x a C Pulse value a Prescaling value 123456 Input A 1 es HOLD input Input B I Display play 6 e Re
27. or hardening of the rubber packing may occur and so in order to ensure the level of waterproofing specified in NEMA4 periodic replacement is recommended Note Rubber packing is provided with the Controller omrRONn Main Functions K3HB P E Main Functions and Features Measurement Mor The K3HB R has the following six functions for receiving and displaying input pulses F1 Rotation rpm circumferential speed F2 Absolute ratio F3 Error ratio F4 Rotational difference F5 Flow rate ratio F6 Passing time The K3HB P has the following six functions for receiving and displaying input pulses F1 Passing speed F2 Cycle F3 Time difference F4 Time band F5 Measuring length F6 Interval The K3HB C has the following three functions for receiving and displaying input pulses F1 Individual inputs F2 Phase differential inputs F3 Pulse counting input Filters Input Types in ER cn tb in ER Specify the types of sensor connected to input A and input B Key Operations Key Protection Key protection restricts level or parameter changes using the keys to prevent unintentional key operations and malfunctions Outputs Comparative Output Pattern oE P Standard zone and level comparative output patterns can be selected for comparative outputs OME CES ME OEP Holds the output status when a comparative result output other than PASS turns ON PASS Output Change Bes
28. tact or voltage pulse input Contact Note Set to i or i when there is a large variation in the display The largest measurement range is 30 Hz omrRONn K3HB P Common Specifications E Event Input Ratings Contact ON 1 KQ max OFF 100 kQ min No contact ON residual voltage 2 V max OFF leakage current 0 1 mA max Load current 4 mA max Maximum applied voltage 30 VDC max E Output Ratings Contact Output Transistor Outputs Resistive loads Inductive loads i 250 VAC cos 1 250 VAC closed Maximum load voltage 24 VDC 30 VDC L R 0 ms circuit coso 0 4 Maximum load current 50 mA 30 VDC L R 7 ms Leakage current 100 uA max Rated load 5 A at 250 VAC 1 A at 250 VAC 5 A at 30 VDC 1 A at 30 VDC Mechanical life 5 000 000 operations expectancy Electrical life 100 000 operations expectancy Linear Output tem Outputs 0 to 20 mA Allowable load impedance 500 Q max 5 kQ min Resolution Approx 10 000 Output error 0 5 FS 0 5 FS 0 15 V for 1 V or less and no output for 0 V Serial Communications Output BCD Output I O Ratings Input Signal Logic Negative Communications method Half duplex Synchronization method Start stop synchronization asynchronous Baud rate 9600 19200 38400 bps Transmission code ASCII Data length 7 bits or 8 bits Stop bit length 2 bits or 1 bit Error detection Vertical parity and FCS Parity check Odd even
Download Pdf Manuals
Related Search