INSTRUCTION MANUAL DX200 S83
Contents
1. 19 3 5 2 1 Scale Display 19 3 5 2 2 Switching the Display Rate 19 3 5 8 Communication 20 3 6 Green Band and Alarm Mark Display Functions 21 3 6 1 Green Band Display Function eese 21 3 6 1 1 21 3 6 1 2 Green Band Display Image 22 3 6 2 Alarm Mark Display Function necesse nennen 23 3 6 2 1 23 3 6 2 2 Display Images ite E eret 24 3 6 3 1 25 3 6 4 Communication 26 3 7 Media FIFO FU HO neun u c Qe 27 3 7 1 Specifications icc eire reri 27 3 72 o 28 3 7 8 Communication Commands eese essen nennen 28 3 8 Internal Switch 29 3 82. 37 3 13 SNTP Server Client Functions eeeeeeeees 38 3 13 1 Specifications of SNTP Server Function 38 3 13 2 Specifications of SNTP Client Function 38 IM DX200 S83E 3 13 3 Procedure 39 3 13 3 1 SNTP Basic 39 3 13 3 2 Communication Commands for SNTP Basic Setting 40 3 13 3 3 SNTP Operation Setting at Memory Start 41 3 13 3 4 Communication Commands for SNTP Operation Setting 41 at Memory Start 3 13 4 SNTP Operation at Memory 42 3 13 5 SNTP Operation with Manual Operation 42 3 13 6 SNTP LOG Re 43 44 3 14 1 Addition of Waveform Colors eee 44 3 14 2 Increased Number of Characters Used in Arithmetic Expressions 44 3 14 3 Changing Historical Window Switch Method Appendix Drawings IM DX200 S83E 1 Foreword Thank you for purchasing the DX200 This user s manual contains hardware specification and additional firmware specifications for DX200 listed below
3. Fig 3 6 5 Green Band and Alarm Mark setting menu Table 3 6 3 Items to be added No Description Item Name Selection Description Presence absence of Alarm mark On Displayed 1 alarm marks on scale Of Not displayed Presence absence of Band area Off Not displayed pangs In Displayed inside 2 specified positions Out Displayed outside specified positions 3 Green band color Color Selectable color for waveform 4 Green band position Lower 0 to 99 lower 5 Green band position Upper 1 to 100 upper If None is selected alarm marks on bar graphs shall be the same as those provided on the standard model IM DX200 S83E 26 3 6 4 Communication Commands e Anew command to show or hide alarm marks and green bands shall be added QHp1 p2 p3 p5 Display settings for alarm mark and green band p1 Channel no 01 to 60 p2 Set whether to show or hide alarm marks on scale ON OFF p3 Set whether to show or hide green bands on scale ON IN OUT p4 Green band color RED GREEN BLUE BROWN PURPLE ORANGE LIGHT BLUE GRAY VIOLET YELLOW DARK BLUE CYAN Y GREEN LIME B VIOLET LIGHT GRAY BLACK p5 Green band bottom position 0 to 99 p6 Green band top position 1 to 100 IM DX200 S83E 27 3 7 Media FIFO Function 3 7 1 Specifications a When media FIFO is selected when the external media becomes full or the number of files in th
4. The day of the week to change the time system to the standard time is set Sunday to Saturday 4 Hour of the day An hour to change the time system to the standard time is set 0 to 23 3 11 3 Communication Commands a DST enable disable setting RD p1 1 DST enable disable On Off b Summer winter time setting RT p1 p2 p3 p4 p5 p6 p7 p8 p1 Month to change to the DST p2 Week No to change to the DST Where the day of the week to change to the DST ranks in the month p3 Day of the week to change to the DST p4 Hour to change to the DST p5 Month to change to the winter time Week No to change to the standard time Where the day of the week to change to the standard time ranks in the month p7 Day of the week to change to the standard time p8 Hour to change to the standard time IM DX200 S83E 36 3 12 Gradual Time Correction Function 3 12 1 Basic Specifications a gt O gt A function is added that corrects the time gradually and completes the time change without effects on the measurement interval if it is required to change the time when operating the key during memory start This gradual time correction function applies to all time changes of DX during memory start Time change by key operation Time change by communication command Time change by remote time adjustment function Time change by SNTP client function For details about SNTP see section 3 13 SNTP server client funct
5. OFF p3 Switches all channel display and group display ALL GROUP p4 Turns scale display on and off and sets the type ON OFF BAR On Displays the scale display with a mark same as standard unit OFF No scale display BAR Displays scales in a bar graph p5 Turns the digital display ON OFF ON OFF IM DX200 S83E 21 3 6 Green Band and Alarm Mark Display Functions 3 6 1 Green Band Display Function 3 6 1 1 Specifications a In the scale and bar graph views of the trend window green bands are displayed in the specified color For display examples refer to Figs 3 6 1 and 3 6 2 b The green band area can be set either inside or outside the specified positions Table 3 6 1 Green Band type Selection Display example Inside 2 8 1 2 0 4 u 8 4 1 2 zi Outside a 152 Lud 1112 d c The top and bottom of the Green Band area are set within the range of 0 to 100 Up to 196 width can be set IM DX200 S83E 22 3 6 1 2 Green Band Display Image a Trend Window ee ur Lu ucc cuc i t H 8 466 8 469 B 455 8 458 Fig 3 6 1 Green Bands on scales b Bar Graph Window ham 2 08 ham 1 L vr I Aas 4 44 Fig 3 6 2 Green Bands on bar graphs IM DX200 S83E 3 6 2 3 6 2 1 23 Alarm Mark Display Function Specifications a Displays alarm marks on
6. Please refer to DX200 standard user s manual IM04L02A01 01E Hardware specifications Westronics 3200 panel cut size Addition of TC RTD input types Message expansion Automatic monitor window recovery Split trend display only for DX100 Simultaneous use of log input and Math options Scale display and display rate switching Green band and alarm mark display Media FIFO Internal switch MEDIA key Auto Recovery Function of Modbus Master Daylight saving time Gradual Time Correction Function SNTP Server Client Addition of Waveform Colors Increased Number of Characters Used in Arithmetic Expressions IM DX200 S83E 2 Hardware Specificarions 2 1 Construction e Material Case Drawn steel Bezel Polycarbonate e Case color Grayish blue green Munsell 2 0B 5 0 1 7 or equivalent e Bezel color Black e Dimensions Please refer to appendix e Weight DX204 S83 approx 7 5kg DX208 S83 approx 7 7kg DX210 S83 approx 7 5kg DX220 S83 approx 7 8kg DX230 S83 approx 8 2kg DX204 S83 approx 7 5kg e Front panel Water and dust proof not available e Key panel MEDIA key is added This will be pressed when the external storage medium is inserted to the drive The storage medium is detected and operation to save the data to the external storage medium can be followed e Terminal arrangement of back panel Please refer to appendix e Panel cut Please refer to appendix e Fuse There is not the fuse on DX 2 2 Safety and EMC Stan
7. 2 2 2 Writing Pre determined Messages 1 Press FUNC key and press soft key corresponding to Message 2 Alist of message group Nos and group names will appear GROUP 1 san 2099 09 13 51 0197 Heceeoe Group ligt Group Group Groups Groured Groups Grouse Group Group Group Group T Greupd ZEE 529 Fig 3 2 2 Writing pre determined messages 1 3 Select the group No of the message you want to write Hezeege liat 2 Hessspe3 MESSAGE jJ Heaseged MESSAGES amp HessegeT Hesseges Fig 3 2 3 Writing pre determined messages 2 4 Click the soft key corresponding to the message you want to write The message will be written IM DX200 S83E 3 2 2 3 Writing Free Messages 1 Press FUNC key press soft key corresponding to Message A list of message group Nos and group names will appear Press the soft key corresponding to Free Select the desired message No Each message No has its own color mark GROUP 1 Are E PEN AL 6hour Fig 3 2 4 Entering contents of free message 5 Awindow allowing you to enter message contents will appear Enter the desired characters and press the DISP ENTER key The message will be written 3 2 3 Communication Command A command for automatic monitor window recover
8. No 1to8 IM DX200 S83E 31 3 8 3 Communication Commands e Commands to assign actions to internal switches shall be added QJp1 p2 p3 p4 Internal switch No S01 to S30 p1 p2 p3 p4 Action to be assigned NONE ALARM ACK MEMORY START STOP MANUAL SAMPLE TRIGGER MESSAGE MATH START STOP MATH RESET SNAPSHOT FREEZE MEMORYCLEAR RATECHANGE Message group No No action Alarm ACK Memory start stop Manual sample External trigger input event data Message writing Math start stop Math reset Snap shot Screen refresh stop Memory clear Display rate change Effective when p2 MESSAGE 1to7 Message No Effective when p2 MESSAGE 1to8 IM DX200 S83E 32 3 9 MEDIA key 3 9 1 MEDIA key This will be pressed when the external storage medium is inserted to the drive The storage medium is detected And the icon of external storage medium appears on the status display section 3 9 1 Manual Save In case that the way of manual save setting is selected as saving to the external storage medium save data as following directions a Insert the external storage medium into the drive b Push MEDIA key and the external storage medium will be inspected The internal memory data can be saved into the external storage medium IM DX200 S83E 33 3 10 Auto Recovery Function of Modbus Master 3 10 1 Specifications a b Auto recovery function which functions if
9. for the log input channel With Yokogawa s Viewer software such as DAQSTANDARD LACK will be displayed 3 4 2 Procedure 3 4 2 1 rog display Press the MENU key to enter the Set mode Press the soft key corresponding to Range Alarm Set the channels for First channel and Last channel Set the measurement range and span Set the exponent of the upper and lower limits of the scale o Note e You can set the scale value in the range from 1 0E 15 to 1 0E 15 e The maximum exponential difference between the lower and upper limits of the scale is 15 e The alarm hysteresis is fixed to 0 e The alarm value is set using a voltage value e Alarm type is H L T t 3 4 2 2 Setting remote control In the procedure given in section 10 9 in the DX200 User s Manual assign Freeze or Memory clear to the remote control action 3 4 2 3 Turning ON OFF the time display 1 Press the MENU key to enter the Set mode 2 Press the FUNC key for three seconds to enter Setup mode 3 Press the Next soft key numerous times until AUX appears 4 Press the soft key corresponding to AUX to display the setting screen 5 Move the cursor to Time indicate and set ON OFF nn 1 Ta alarm lh Fpi r T pra Dem Irem Fig 3 4 1 Turning ON OFF the time display IM DX200 S83E 14 3 4 2 4 Setting the number of displayed digits fo
10. getting Error No Detailed code access to the SNTP server Fig 3 13 3 Example of SNTP log screen Table 3 13 2 List of SNTP log error codes Detailed code Contents SUCCESS Succeeded OVER Value exceeds the correction critical value DORMANT Internal process error HOSTNAME It is failed to match the host name TCPIP Internal process error SEND It is failed to send the request TIMEOUT Response time out occurs BROKEN Packet is corrupted LINK Data link is broken b The SNTP log is output through the communication using the FL command 1 Communication command FL p1 p2 p1 Type of log SNTP p2 Maximum read out length of log 1 to 50 Output format yy Year 00 to 99 mo Month 01 to 12 dd Day 01 to 31 hh Hour 00 to 23 mi Minute 00 to 59 ss Second 00 to 59 nnn Error code blank or __1 to 999 XXXXXXXXX Detailed code 9 characters IM DX200 S83E 3 14 3 14 1 3 14 2 44 Others Addition of Waveform Colors a Black color added as waveform color b The background of the historical trend window is changed to a color that allows recognition of the black color c With Yokogawa s Viewer software such as DAQSTANDARD dark blue will be used Increased Number of Characters Used in Arithmetic Expressions a Up to 120 characters can be used in arithmetic expressions b Stack number of channels and constants used in arithmetic expressions shall be extende
11. the communication is disconnected by communication fail or faulty slave device is built into the Modbus master function The Modbus master auto recovery is set up using the communication setup Modbus master in the setup mode When using the auto recovery function an auto recovery cycle is set at the same time The Modbus master auto recovery function is performed at intervals of cycles set in from the hour zero minute position The auto recovery is performed for all connected slave devices 3 10 2 Procedure 3 10 3 Setup Hode cat Modbus Fig Basic settings Read cycle Timaout Retrials Command wait tima NR 3 4 5 1 f 3 10 1 Modbus master setup screen Table 11 1 shows the setting items of the Modbus master auto recovery Table 3 10 1 Setting items of Modbus master auto recovery No Setting item Setting range Contents 1 On Off On Off Set whether or not the auto recovery function is used When selecting On items used to set the auto recovery cycle are displayed 2 Cycle 1min 2min 5min When using the auto recovery function set an auto 10min 20min recovery cycle 30min 1h Communication Commands The following shows the communication command to set the Modbus master auto recovery MM p1 p2 p1 Auto recovery function On Off On Off p2 Auto recovery cycle 1min 2min 5min 10min 20min 30min 1h IM DX200 S83E 3 11 3 1
12. the scales and bar graphs of the trend window b Alarm marks are shown in the following colors The display colors will not change even if alarms occur Table 3 6 2 Alarm Mark display colors Alarm level Color Level 1 Red Level 2 Orange Level 3 Orange Level 4 Red c Alarm marks will be displayed only for the following alarm types Upper limit alarm Lower limit alarm e Delay upper limit alarm T e Delay lower limit alarm t d If an alarm value is set beyond the scale upper or lower limit an alarm mark will be displayed at the corresponding edge of the scale IM DX200 S83E 3 6 2 2 Display Images a Trend Window mE B3 _ chor 12 Ja n4 T T ite 4 T Perte 1 Fig 3 6 3 Alarm Marks on scales b Bar Graph Window Ram 2 23 Al 1 tw f 861 8 455 8 654 8 457 Fig 3 6 4 Alarm Marks in bar graphs 24 IM DX200 S83E 25 3 6 3 Procedure 1 Press the MENU key to enter the Set mode 2 Press the soft key corresponding to Display 3 Press the soft key corresponding to Zone Graph 4 Move the cursor to items shown in Table 3 6 3 and select items or input number GROUP 1 ALL DS Di soley sone Graphs First CH Last th LI ET Zone Louer Diuision 18 Bar arash Borsa Seale peaition 1
13. to set up whether or not DX is operated as SNTP server Select Use or Not SNTP client function setting SNTP client function enabled disabled Select Use or Not When Not is selected the following setting items cannot be set Server name port number access interval access reference time time out Server name Set a SNTP server name using the host name or IP address Port number Set a port number of the SNTP server The initial value is 123 IM DX200 S83E 40 4 Access interval e Seta time interval to access the time of the SNTP server e When Off is selected the periodic access to the SNTP server is not performed 5 Access reference time e The access to the SNTP server is performed at intervals based on the set reference time Set a hour and minute e When the access interval is set at Off this setting becomes invalid 6 Time out Seta period of time to wait for response from the SNTP server e Select a time out from 10s 30s and 90s 3 13 3 2 Communication Commands for SNTP Basic Setting a The SNTP server function is set using the WA command WA p1 1 SNTP server function enabled disabled Use Not b The SNTP client function is set using the WB command WB p1 p2 p3 p4 p5 p6 1 2 4 5 SNTP client function enabled disabled Use Not SNTP server name Up to 64 alphanumeric characters Port number of SNTP server 0 to 655
14. 1 Specifications 29 3 8 2 e jp 30 3 8 8 Communication nunne nananet 31 3 9 MEDIA 32 3 9 1 MEDIA KOV LE LN 32 3 9 2 Manual 5 anc eene cn ne oc n neu CY va vC 32 3 10 Auto Recovery Function of Modbus Master 33 3 10 1 SpecifICatiOns 33 3 10 2 33 3 10 3 Communication nunne nanne nnmnnn 33 3 11 Changing of DST Daylight saving time setting method 34 3 11 1 Specifications 34 3 11 2 Procedure 4 3 11 3 Communication 35 3 12 Gradual Time Correction Function 36 3 12 1 Basic 36 3 12 2 Gradual Time Correction Function Setting 37 3 12 2 1 Settings on Screen 37 3 12 2 2 Communication Command
15. 1 1 3 11 2 34 Changing of DST Daylight saving time setting method Specifications By setting the month day of the week week and time it becomes unnecessary to set the DST every time the system is started up Be sure to set Time Zone when using DST Procedure The DST is set on the screen in the set mode When selecting the DST soft key the DST setup screen see Fig 3 11 1 will appear On this screen the specified DST can be set EHF op rp EIN EL 5 i HE NE ID NET Daulisht savings tine Fig 3 11 1 DST setup a DST Use Not setting To use the DST select Use e When selecting Use the summer time winter time setting item screen will appear b DST setting Start time 1 Month A month to change the time system to the DST is set 1 to 12 2 Day order Where the day of the week to change the time system to the DST ranks in the month is set 1 2 3 4 Last 3 Weekday The day of the week to change the time system to the DST is set Sunday to Saturday IM DX200 S83E 35 4 Hour of the day An hour to change the time system to the DST is set 0 to 23 c Winter time setting End time 1 Month A month to change the time system to the standard time is set 1 to 12 2 Day order Where the day of the week to change the time system to the standard time ranks in the month is set 1 2 3 4 Last 3 Weekday
16. 35 Access interval Off 1h 8h 12h 24h Access reference time 00 00 to 23 59 Time out 10s 30s 90s IM DX200 S83E 41 3 13 3 3 SNTP Operation Setting at Memory Start a When selecting 2 SNTP synched to start the screen shown in Fig 3 13 2 will appear b This setting is used to correct the time using the SNTP client when executing the memory start c Select On or Off d The memory start is executed regardless of the time adjustment by SNTP e This setting is valid even in the memory start by the remote or communication command SHIP SST to start SHIP synched ta start Tim atic on tart action E ot Fig 3 13 2 Screen for SNTP setup at memory start 3 13 3 4 Communication Command for SNTP Operation Setting at Memory Start The SNTP operation at memory start is set using the WC command WC p1 p1 SNTP time adjustment On Off at memory start On Off IM DX200 S83E 42 3 13 4 SNTP Operation at Memory Start a The access to the SNTP is performed at memory start However if any response is not received from the SNTP server within 2 sec after that the memory start is executed regardless of access to the SNTP server b If the access to the SNTP server is succeeded after memory start the same operation as the time setting during memory start is performed c The communication response of the memory start PSO by the commun
17. 3E 3 1 2 RTD Inputs Resistance Temperature Detector e Table 3 1 2 shows added RTD inputs if the system Table3 1 2 RTD Inputs added Without N1 option Range Range Measurement range Measurement accuracy Max name resolution JPt50 PT3 200 0 to 550 0 C 0 3 of rdg 0 6 C 0 1 C 328 0 to 1022 0 F 0 1 F Ni100 SAMA 1 200 0 to 250 0 0 15 of rdg 0 4 C 0 1 C 328 0 to 482 0 F 0 1 F Ni100 DIN Ni2 60 0 to 180 0 C 0 15 of rdg 0 4 C 0 1 C 76 0 to 356 0 F 0 1 F Ni120 Ni3 70 0 to 200 0 C 0 15 of rdg 0 4 C 0 1 C 94 0 to 392 0 F 0 1 F J263 B J263 0 0 to 300 0 K 0 to 40K Within 3 0K 0 1K 40 to 300K Within 1 0K Cu53 CU8 50 0 to 150 0 C 0 15 of rdg 0 8 C 0 1 C 58 0 to 302 0 F 0 1 F Cu100 CU9 50 0 to 150 0 C 0 2 of rdg 1 0 C 0 1 C 58 0 to 302 0 F 0 1 F e Table 3 1 3 shows added RTD inputs with N1 option Table 3 1 3 RTD Inputs added with N1 option Range Range Measurement range Measurement accuracy Max name resolution JPt25 PT4 200 0 to 550 0 C 0 15 of rdg 0 6 C 0 1 C 328 0 to 1022 0 F 0 1 F IM DX200 S83E 3 2 Message Expansion 3 2 1 Basic Specifications a There are 7 groups of messages with 8 messages per group Any message can be written using keypad and communication commands A message can be assigned to a remote inputs and USER key for
18. INSTRUCTION MANUAL DX200 S83 IM DX200 S83E 2nd Edition 2nd Edition June 2004 YK All Rights Reserved Copyright 2004 Yokogawa Electric Corporation Toc 1 DX200 S83 IM DX200 S83E 2nd Edition CONTENTS 1 FOISWOPIT i eani EINE MM IMEEM MM EDEN 1 2 Hardware Specifications 2 PA MEC 3040 1 2 2 2 Safety and EMC Standards 2 2 3 Optional Functions nid rni rrt dnd va ka ada eai vaa 2 2 4 Application Software 2 3 Additional Firmware Specifications 3 3 1 Addition of TC and RTD Input Types 3 3 1 1 Additional TC Inputs Thermo coupler 3 3 1 2 RTD Inputs Resistance Temperature Detector 4 3 2 Message Expansion 5 3 2 1 Basic Specifications 5 3 2 2 E 6 3 2 2 1 Setting Message 3 2 2 2 Writing Pre determined
19. Messages 7 3 2 2 3 Writing Free Messages tede acere eia 8 3 2 5 Communication Command eese nennen nnns 8 3 3 Automatic Monitor Window Recovery Function 9 3 3 1 Basic 9 3 3 2 eiie on ex xu Ru de eu een S cu EE eque 10 3 3 3 Registering the Window to be Automatically Recovered 11 3 3 4 Communication 11 3 4 Log Display and Simulation Function 12 3 4 1 Specifications a e iori 12 3 4 2 Procedure cere c er neee ccnttcedenceccuucdeneddesncechtddeedeceedddarenueuedenttece 13 3 4 2 1 L409 display eie bis 13 3 4 2 2 Setting remote control sse 13 3 4 2 3 Turning ON OFF the time display 13 3 4 2 4 Setting the number of displayed digits for measured data 14 3 4 3 Communication 15 3 5 Scale Display and Switching Display Rate 17 3 5 1 Specifications iiec ier iecur eeu 17 IM DX200 S83E 3 52
20. Switching the Display Rate 1 2 3 Press MENU to enter set mode Press the 3 soft key to display the set screen Set the second display update rate The available settings are the same as the standard display update rate settings interval Ting diu nin save interval 1 Second tina diu inin Fig 3 5 1 Switching the Display Rate Switching the Display Update Rate There are four methods for switching the display update rate Using the FUNC key see section 3 4 Run Mode in the standard user s manual Using the remote control function with the R1 option see section 10 9 Setting the Remote Control Functions R1 Option Basic Setting Mode in the standard user s manual Using communications commands see page 20 e Using internal switch function see page 29 IM DX200 S83E 3 5 3 20 Communication Commands QE Setthe 2nd display update rate Syntax p1 lt terminator gt p1 2nd display rate 15 s 30 s 1 min 2 min 5 min 10 min 20 min 30 min 1 2 h 4 h 10 h 15 s and 30 s for the DX102 DX104 DX204 and DX208 only QF Switching the display update rate Syntax QF p1 lt terminator gt p1 Operation Type 0 Changes to the 1st rate standard rate 1 Changes to the 2nd rate UD p1 p2 p3 p5 Adds p4 to BAR Syntax UD p1 p2 p3 p4 p5 lt terminator gt p1 Switching the Display 4 p2 Enables disables automatic monitor scroll ON
21. activation e Assign a group name for message groups b There are eight types of free messages Free messages can be written using keys communication commands and via Web Only free messages can be written via web Message character strings that have been defined on DX will remain unchanged if a message is written Table 3 2 1 Message types and writing enable disable Message type Key Communication Remote USER key Web operation command input Message Groups 1 to 6 Message Group 7 Free message With Yokogawa s Viewer software such as DAQSTANDARD groups numbers and message numbers are displayed in the tens digit and ones digit respectively lt Example gt A message of Group No 1 and Message No 3 shall be displayed as 13 d System messages power failure message display rate change message are displayed as messages of Group No 0 and Message No 9 IM DX200 S83E 3 2 2 Procedure 3 2 2 1 Setting Message Press the MENU key to enter the Set mode Press the Next soft key untill Message appears Press the soft key corresponding to Message Select the group No of the message you want to set and then specify the desired group name and enter message contents up to 16 characters Boo GROUP uP T piz hour m DT PUTA 0 E 5 1 2 J d 5 7 a Fig 3 2 1 Message setting window IM DX200 S83E 3
22. ction setting menu IM DX200 S83E 11 3 3 3 Registering the Window to be Automatically Recovered 1 Display the desired monitor window 2 Press the FUNC and press soft key corresponding to Standard display The monitor window type and group No in effect when the soft key is pressed is registered as the monitor window to be recovered automatically 1 SES nu zu D OGD 015 Or 3 znn Standard diga Fig 3 3 2 Registering the monitor window to be recovered 3 3 4 Communication Command A command for automatic monitor window recovery added 1 Le IP test Fieldbus QGp1 Allows you to set automatic monitor window recovery p1 Time to be expired before the pre registered monitor window is automatically displayed Off Disables the automatic recovery function 1min 2min 5min 10min 20min 30min 1h IM DX200 S83E 12 3 4 Log Display and Simulation Function 3 4 1 Specifications a Log display Displays the measured data using a Log scale common logarithm The equation is given by Y 10 SU SLXO VL VU VL SL where Input voltage X Lower limit of display span VL Upper limit of display span VU Lower limit of scaling SL Upper limit of scaling SU Displayed value Y b Simulation function You can stop the updating of the display by applying a signal to the remote control terminal or by using a communication command The re
23. d to 35 c The number of constants for DX100 are increased to 30 IM DX200 S83E 45 3 14 3 Changing Historical Window Switch Method 1 When the DISP ENTER key is pressed on the trend window the cursor is placed on the historical trend menu Pressing the DISP ENTER key again causes historical trend to reappear If the DISP ENTER key is pressed on a window other than the trend window the cursor shall be placed on the menu that indicates the current window 2 The menu to switch to the historical window is located below the trend GROUP 1 ALL IS mes 4 2 HISTORY nini di Fig 3 14 1 Window switch menu IM DX200 S83E
24. d to Internal switches and their names Function English Menu FUNC key Memory start stop MemoryStart Stop Memory DX100 Start Stop DX200 Event data trigger Trigger Trigger Alarm ACK AlarmACK AlarmACK Math start stop MathStart Stop Math Math reset MathReset Math rst Manual sample ManualSample M sample Snap shot SnapShot Snapshot Message writing 7 Message Message Screen refresh stop Freeze Freeze Simulation Memory clear Simulation Memory Clear Clear Display rate change Rate Change Change No assignment None None ae Message group Nos and message Nos need to be set separately 2 Used by the simulation function 3 To be added for this custom made order IM DX200 S83E 3 8 2 30 Procedure Press the MENU key to enter the Set mode Press the FUNC key for three seconds to enter the Setup mode Press the Next soft key numerous times until Switch Action settings appears Press the soft key corresponding to Switch Action settings to display the setting screen Move cursor to items that are shown in Table 3 8 2 and select one Setup Hode Fig 3 8 1 Setting Internal switches Table 3 8 2 Items to be added No Description Item Name Selection 1 Internal switch No Switch No S01 to S30 2 Action to be assigned to internal Action Refer to Table 10 1 switch 3 Message group No Message group 1to7 4 Message No Message
25. dards e Safety standards Certificated by CSA22 2 No 1010 1 Complies with EN61010 1 e EMC standards Complies with EN61326 1 2 3 Optional Functions Following optional functions can not be specified ICF1 H2 H5 4 P1 D5 2 4 Application Software Only DAQSTANDARD 5120 supports the setting of additional firmware functions IM DX200 S83E 3 3 1 Addition of TC and RTD Input Types 3 1 1 e Table 3 1 1 shows added TC inputs Table3 1 1 TC Inputs to be added Additional Firmware Specifications Additional TC Inputs Thermo coupler Range Range Measurement range Measurement accuracy Max name resolution Kp vs Au7Fe Kp 0 0 to 300 0 K 0 to 20K Within 4 5K 0 1K 20 to 300K Within 2 5K PLATINEL PLATI 0 0 to 1400 0 C 0 25 of rdg 2 3 C 0 1 C 32 to 2552 F 1 F PR4O 20 PR 0 0 to 1900 0 C 0 to 450 C 0 1 C 32 to 3452 F Accuracy not guaranteed 1 F 450 to 750 C 0 9 of rdg 16 0 C 750 to 1100 C 0 9 of rdg 6 0 C 1100 to 1900 C 0 9 of rdg 2 0 C NiNiMo NiMo 0 0 to 1310 0 C 0 25 of rdg 0 7 C 0 1 C 32 to 2390 F 1 F WRe3 25 WRe 0 0 to 2400 0 C 0 3 of rdg 2 8 C 0 1 C 32 to 4352 F 1 F W WRe26 W WRe 0 0 to 2400 0 C Within to 400 C 15 0 C 0 1 C 32 to 4352 F 400 to 2400 C 1 F 0 2 of rdg 2 0 C TypeN AWG14 N2 0 0 to 1300 0 C 0 2 of rdg 1 3 C 0 1 C 32 to 2372 F 1 F IM DX200 S8
26. displayed digits 2 Display using two digits 3 Display using three digits QA Set the number of displayed digits of the mantissa to two QA2 QB Stops Resumes the updating of the display and clears the internal memory and the trend Syntax Query Example QB pi lt terminator gt p1 Operation 0 Resume the updating of the display 1 Stop the updating of the display 2 Clear the internal memory and the trend QB Stop the updating of the display QB 1 IM DX200 S83E 16 QC Turns ON OFF the time display Syntax QC pi lt terminator gt p1 Turn On Off the time display Query QC On Time indicate On Off Time indicate Off Example Turn Off the time display QC Off IM DX200 S83E 17 3 5 Scale Display and Switching Display Rate 3 5 1 Specifications a Scale Display You can display the current value instead of a mark for the trend display in the bar graph If several channels are assigned to a scale only the first channel specified in the display group settings can be displayed for the current value of the scale in the bar graph Bar Graph Starting Point When the direction of the trend display is vertical The starting point for the scale bar graph is the same as that when the measured value bar graph is horizontal When the measured value bar graph is vertical the starting point for the scale bar graph also reverts to Standard When the display direction of the trend display is horizontal The star
27. e folder reaches 1 000 the oldest file will be deleted and the latest data file will be saved All the files in the specified folder are subject to automatic deletion In the following cases files will not be deleted even if they are old If the folder name is changed data files in the previous folder name will not be deleted Read only files system files hidden files No warning will be given even if the remaining capacity on the external media reaches less than 10 of total capacity The following will take place if an error occurs with the external media The media icon in the status display area switches to an error mark Memory full relay will be excited An E mail will be sent Status information of communication interface will be shown ACK will be issued as shown below in case of media error After media error occurrence media check is performed in case of the front door closed and ACK will be issued if it is confirmed that the media is normal and if media format is done normally However ACK will not be issued if the front door is closed in the basic setting mode setup mode After ACK is issued the media icon will return to the original mark The following files will be re created when they exceed 100 k bytes in file size The files will be divided into blocks Manual sample report data weekly report monthly report TLOG data For hourly and daily reports the file split function is pro
28. he unit Number of Data The number of TLOG report and manual sample data that can be saved to the internal memory is as follows Main Unit Standard DX TLOG 30 400 Report 5 40 Manual Sample 5 50 When using Autosave the above limits on the number of data do not apply since data is saved to the external memory medium at each time up When saving TLOG data using Autosave a TLOG file is created every 30 data Note If no external memory medium is installed the number of data that can be saved to internal memory is reduced c Message Display upon Restart after Power Failure If a power failure occurs while saving data to the internal memory once the power is resumed the time of resumption is displayed Message 9 appears in burgundy as follows Time Date of Power Resumption Power Fail Ex May 15 Power Fail The time the message was written is displayed before the message Note With the DX200 s 4 screen display no message is displayed With trend screen of DX200 s 4 screen display scale is displayed IM DX200 S83E 19 3 5 2 Procedure 3 5 2 1 Scale Display 1 2 3 Press DISP ENTER to display the screen menu Press the right arrow key to display the submenu Choose SCALE BAR from the submenu If the SCALE BAR does not appear select the view display items then press DISP ENTER one or two times The display toggles between SCALE BAR SCALE OFF and SCALE ON 3 5 2 2
29. ication command shows whether or not the memory start is succeeded Whether or not the SNTP access is succeeded at memory start is checked using status information 2 of the status byte Table 3 13 1 Status information 2 of SNTP operation at memory start Bit Name Description 4 SNTP operation at start This bit becomes 1 if the time is not adjusted by SNTP 3 13 5 SNTP Operation with Manual Operation a From the menu screen that appears by selecting the FUNC key select SNTP to execute the SNTP operation e SNTP can be selected only when the SNTP client function is set at Use e The SNTP operation can be executed regardless of the memory start memory stop status b If any response is not returned from the SNTP server or if the contents of the response are illegal relevant error is given c Communication command e The SNTP operation is performed using the CL command CL p1 p1 Time adjustment with manual operation 0 Run IM DX200 S83E 43 3 13 6 SNTP Log a The operation log of the SNTP SNTP log can be checked on the screen of DX From the menu screen that appears by selecting the FUNC key select LOG and SNTP in that order The SNTP log appears on the screen Fig 3 13 3 shows an example of the SNTP log screen Table 3 13 2 shows the list of detailed codes shown on the SNTP log screen 882 882 Time No Code Feb 29 2004 16 31 52 Date and time when
30. ions Before using the gradual time correction function a critical value is set for the difference between the current time and the time to be adjusted When the difference between the time to be adjusted and the time set on DX exceeds the set critical value if any factor needing the time change arises the time is not corrected gradually but the time is corrected at once When Off is selected during setting of time deviation limit the gradual time correction function does not function The gradual time correction function adjusts the time at a rate of 15 625 msec sec The time on the status display screen is shown in yellow while the time is being corrected gradually The gradual time correction function functions only when the following two conditions are satisfied In other case the time is not corrected gradually but the time is changed at once Operation must be in the memory start status The difference between the time to be adjusted and the time set on DX must be within time deviation limit if any factor needing the time change occurs IM DX200 S83E 37 3 12 2 Gradual Time Correction Function Setting 3 12 2 1 Settings on Screen a To set up the gradual time correction function select Date amp Time Time zone in the setup mode b When selecting Date amp Time Time zone the screen shown in Fig 3 12 1 will appear Set a critical value for the difference between the time to be adjusted and time
31. lationship between the signal that is applied to the remote control terminal and the updating of the display is as follows Close Open Update Stop the updating Update the display of the display the display gt When the updating of the display is resumed the current waveform is displayed from the stopped position Waveform before the updating of the display was stopped Position where the updating of the waveform was stopped Waveform after resuming the updating of the display c Clearing the internal memory displayed waveform You can clear the internal memory and the displayed trend by applying a signal to the remote control terminal Both the internal memory and the trend are cleared when the input signal to the remote control terminal changes from open to close d Turning ON OFF the time display You can turn ON OFF the time display e The number of displayed digits for measured data You can set the number of digits of the mantissa to two or three digits when displaying the digital value in exponential form IM DX200 S83E 13 Note e Allows log input for models equipped with the math option f the log input channel is included in arithmetic expressions setting shall be allowed but an error will occur for math results e An error will appear for statistical computation if the log input channel is assigned to the report channel e In the Tlog file an error will be set for measurement results
32. r measured data 1 Press the MENU key to enter the set mode 2 Press the FUNC key for three seconds to enter setup mode 3 Press the soft key corresponding to A D DX100 or Alarm A D DX200 to display the setting screen 4 Move the cursor to Display digits and set 2 or 3 Setup Hede AD Integrate ute Scan interval 1 Loa re digits E Fig 3 4 2 Setting the number of displayed digits for measured data IM DX200 S83E 3 4 3 15 Communication Commands SR Sets the input range Syntax Query Example Description SR p1 p2 p3 p4 p5 p6 p7 p8 p9 lt terminator gt p1 Channel number DX100 01 to 12 DX200 01 to 30 p2 Input type Log p3 Measurement range 20 mV 60 mV 200 mV 2 V 6 V 20 V 50 V p4 Lower limit of span p5 Upper limit of span p6 Lower limit of exponent 15 to 15 Upper limit of exponent 15 to 15 p8 Decimal position fixed to 0 p9 Unit up to 6 characters SR Set CH2 to log display the measurement range to 6 V the span to 6 V to 6 V the upper limit of exponent to 5 upper limit of exponent to 6 the decimal position to 0 and the unit to abc SR 02 Log 6V 6000 6000 5 6 0 abc Make sure p7 p6 does not exceed 15 For details on the other parameters see the Communication Interface User s Manual QA Sets the number of displayed digits of the mantissa Syntax p1 Query Example QA p1 lt terminator gt Number of
33. set on DX in the Time deviation limit setting item d Select a desired setting from the following Swstam Fig 3 12 1 Gradual time correction function setup screen 3 12 2 2 Communication Command The gradual time correction function is set using the RG command RG p1 p1 Critical value for difference between time to be adjusted and current time IM DX200 S83E 38 3 13 SNTP Server Client Functions 3 13 1 Specifications of SNTP Server Function a DXis operated as SNTP server b When operated as SNTP server the time resolution becomes 15 625 msec c When operated as SNTP server the port number is fixed at 123 3 13 2 Specifications of SNTP Client Function a When using the SNTP client function the time of DX is adjusted to the time of the SNTP server b There are three kinds of methods to access the time of the SNTP server as described below 1 Periodic access e The access interval may vary depending on the setting 2 Access when executing the memory start e This operation may vary depending on the On Off setting 3 Access by manual operation c The time correction operation may vary depending on the memory sample status of DX 1 During memory start When the gradual time correction function is set enabled the ime is corrected gradually For details see section 3 12 Gradual time correction function 2 During memory stop The time is adjusted at once as the time adjustmen
34. t is requested d The access log from the SNTP client to the SNTP server is recorded in SNTP log The SNTP log can be checked through the screen of DX or by outputting the log using the communication command e An error of 125 msec or less is not corrected f If the time cannot be corrected by the SNTP client function relevant error is given The following shows error occurrence conditions 1 Access to the SNTP server is failed due to response time out 2 The contents of the response from the SNTP server are illegal 3 Ifthe time difference between DX and the SNTP server exceeds 10 min during periodic access the time is not corrected IM DX200 S83E 39 3 13 3 Procedure 3 13 3 1 a To setup the SNTP function on the screen select the SNTP soft key in the setup mode b When selecting the SNTP soft key two selection items related to SNTP are shown as described below 1 1 Basic settings e Make the settings related to the basic operation of the SNTP server client 2 2 SNTP synched to start e Set the time access On or Off when executing the memory start SNTP Basic Setting When selecting 1 Basic settings the screen shown in Fig 3 13 1 will appear SHIP Basic settings Server settings a llse Not tke Client NA b 1 2 3 4 5 ti nanut 6 Fig 3 13 1 SNTP basic setup screen SNTP server function setting This setting is used
35. ting point is the smallest numeric value on the height of the display from top to bottom b Switch the Display Rate When writing data to the internal memory by pressing START the trend display update rate changes to the previously specified setting If the display update rate is changed while data is being written to the internal memory monitor data are created separate from display data to be used for displaying trend data e Monitor data cannot be saved to an external memory medium or output through communications e With historical trends display data is displayed rather than monitor data e When loading trend displays by specifying an item in a summary list display data is loaded e The position when the display update rate was changed is written to message 9 IM DX200 S83E 18 Trend Display Data DX200 models set to Horizontal trend display mode One scale digital off display trend screen is19 5 divisions of data One scale digital on display trend screen is15 divisions of data With combinations of total channels and maximum math computations configured for some DX200 models past trend trace data may be less than the full screen 19 5 or 15 divisions as described above The minimum trend trace data will always be at least 13 divisions of recent trend data once the unit has initially recorded the information No data is lost in the archived data files This may be noticed when switching screens or powering off and on t
36. vided as standard feature The media FIFO function is effective only for those models equipped with ZIP or ATA card IM DX200 S83E 28 3 7 2 Procedure 1 Press the MENU key to enter the Set mode Press the FUNC key for three seconds to enter the Setup mode Press the Next soft key numerous times until AUX appears Press the soft key corresponding to AUX to display the setting screen Move the cursor to Media FIFO and select On Off fede eu Taa Channa Channel alarm Th Languase Partial Met Tine indicate Tim zog 34 Difference fron B 3 Hedia FIFO Fig 3 7 1 Enabling Disabling media FIFO function 3 7 3 Communication Commands Acommand allowing you to enable or disable the media FIFO function added Qlp1 p1 Set whether to enable or disable the media FIFO function ON OFF With the floppy disk model it is not possible to select ON IM DX200 S83E 3 8 Internal Switch Function Specifications 3 8 1 a 30 internal switches 501 to S30 added In addition to 101 to 136 501 to S30 can be selected b Assignment of actions in the basic setting menu Actions that be assigned are given in the table below Assignment to internal switches is made using alarm relay setting item Table 3 8 1 Functions that can be assigne
37. y added a Message character strings setting SG p1 p2 p3 p1 Message group No 1 7 p2 Message No 1 8 p3 Message 16 alphanumeric characters b Message Write MS p1 p2 p1 Message group No 1 7 p2 Message No 1 8 C Message group name setting BG p1 p2 p1 Message group No 1 7 p2 Group name 16 alphanumeric characters d Free message Write BJ p1 p2 p1 Message group No 1 7 p2 Group name 16 alphanumeric characters IM DX200 S83E 3 3 Automatic Monitor Window Recovery 3 3 1 Function Basic Specifications a This function causes the pre registered monitor window to appear automatically in cases where no keys have been pressed for a certain period of time b The time to be elapsed before the pre registered monitor window appears after no keys have been pressed for a certain period of time is selected from the following 1min 2min 5min 10min 20min 30min 1h C This function is effective for monitor window only IM DX200 S83E 10 3 3 2 Procedure 1 Press the MENU key to enter the Set mode 2 Press the soft key corresponding to Display 3 Press the soft key corresponding to View direction LCD 4 Move the cursor to Jump default display time and select time GRWP 1 Jan 2888 80 21 View Direction Leo Brishtness sauer dune default display Digelay tine Fig 3 3 1 Automatic monitor recovery fun
Download Pdf Manuals
Related Search