GPSmart Manual 2013.indd
Contents
1. 6 To verify that the system has been centered press the off button The system will automatically steer to the centered position The accuracy of the steering calibration will impact the system s performance Care must be taken to ensure that the thruster is aligned as accurately as possible ideally within 1 or 2 degrees during this calibration COMPASS MANUAL CALIBRATION Recommended Note Performing a compass calibration procedure is recommended as part of the installation process to improve the accuracy of the GPSmart motor It will account for magnetic errors that can occur if the system is mounted close to other metallic objects i e cleats steel fasteners etc which may cause the system functions to misbehave This routine performs a similar but more accurate calibration than the Compass Auto Calibration however it requires an external means of propulsion i e outboard engine or paddle 1 The boat must be in the water to perform this calibration Make sure that there are no obstructions nearby docks pilings other boats etc and that the water is fairly calm 2 Power up the system and deploy it using the depth collar to adjust the height so that the motor can steer without any obstructions 3 Press the M button to enter Manual Mode Please note that the system is in an operational mode Stay a safe distance away from the propeller to avoid injury Watersnake GIP SMART 4 Using the left and right arrow button2. It s a good idea to always keep a Spare 55504 442 p Female Trolling Motor Connector 2 10 Gauge 12 Volt man ine 55505 12V Male 12V Female 2 wire 2 wire Watersnake 50 Amp Fuse Kit Fuse Kit Assembly We strongly recommend the use of an in line fuse kit to protect your motor from shorts and electrical problems that can lead to over heating of circuit boards in your trolling motor Having other devices hooked up to your motor battery can cause power surges Watersnake Fuse Kits come supplied with a 50 amp fuse and are completely waterproof These simple to install kits are an essential accessory for your motor 55503 Sj iM Trolling Motor Fuse Jarvis Marine WATERSNAKE Watersnake NOTES www watersnake com au 27 WATERSNAKE CONTACT INFORMATION REGION COUNTRY DISTRIBUTOR PHONE Asia Pacific Australia Jarvis Walker 61 3 8787 6900 AUSTRALIAN REPAIRS AND SERVICING Anglers Central Service Centre 2 7 Circuit Drive Hendon Africa South Australia 5014 Australia South Africa Apex Walker 27 11 7920 611 Ph 08 8244 8790 Email spareparts danglerscentral com au www watersnake com au Watersnake Distribution Pty Ltd 297 305 South Gippsland Highway Dandenong South Victoria 3175 Australia ACN 143 230 175 Watersnake and Jarvis Marine are registered trademarks of Watersnake Distr
3. Separate the fob sections 3 Remove the rubber membrane and the circuit board from the back half of the fob shell 4 Slide the battery out of its holder on the back of the circuit board and replace with a new CR2032 battery Be sure to position the battery with the Positive side away from the board Use care not to press the small switch on the back of the circuit board near the battery holder If this switch is accidentally pressed or the unit does not respond to fob commands after replacing a battery please contact your nearest Watersnake dealer for further assistance 9 Reinstall the circuit board in the back half of the fob shell taking care to make sure it is properly positioned in the shell 6 Place the rubber membrane over the lip on the back half of the fob shell and press into place 7 Place the front half of the fob shell over the rubber membrane and press into place Verify that all buttons are properly positioned within their opening and function correctly 8 Reinstall the two screws into the fob shell taking care not to over tighten the Screws Watersnake GIP SMART PROGRAMMING A NEW WIRELESS CONTROL FOB 1 Power up the unit in the stowed position 2 Deploy stow and re deploy the unit prior to pressing any fob buttons 3 The unit will begin beeping indicating that it is ready to learn new wireless controls 4 Press any button on the new fob within 20 seconds 9 When the unit stops beeping
4. press hold the button for 5 seconds The button can then be released and your boat will navigate directly to the last anchor location used The motor will beep a tune hd ox multiple consecutive beeps to indicate that the anchor site has been successfully retrieved The motor will emit two growls and exit if there is no active last memory location the boat is not within 1 mile of the previous location Watersnake GIP SMART TRACK MODE To place the motor in Track Mode press the button with the T symbol on the wireless fob The Track Mode automatically locks in the boat s current heading and controls the steering to maintain a constant track acting as an Autotrack to compensate for wind or current disturbances The operator can adjust the speed or track heading by using the directional controls on the wireless fob qO The motor will emit 1 beep to indicate that it has entered Track Mode The motor will emit 2 growls and exit this 4 mode if there is no GPS fix The direction the boat is pointed when this mode Is selected will become the Track Course The thruster will pull the bow of the boat along this course straight line The boat itself may seem to point somewhat off track due to cross wind or cross track currents ADJUSTING THE TRACK SPEED The motor will maintain its previous speed Track E Mode is selected from the Ma
5. silent the Watersnake electric motors are built to suit all angling conditions High quality materials superior design and precision engineering make these motors longwearing and reliable WARNING Please read manual completely before starting installation Failure to do so may result in accident and or injury SPECIFICATIONS Anchor memory locations 4 Multi use memory locations route or anchor 8 Maximum coarse memory length 1000 Miles Thrust rating 80lbs Operating voltage 24 Volts DC Amperage 0 42 Amps Recommended breaker rating 90 Amps Propeller 3 Blade Weedless Shaft Length 60 Inches The distance of a recorded route will in most cases be limited to the time it takes to traverse or by the battery capacity to power the motor The motor has enough memory to store over 1000 miles or 1600km of courses System draw will alter with level of thrust going up to maximum of 42 Amps at full thrust AS NZS 4268 2012 EMC COMPLIANCE CG N 18365 www watersnake com au IWATIERSNAKES ELECTRIC MoT ors GENERAL INFORMATION The Waternsnake GPS motor has been optimized for use on 16 to 24 foot sport fishing boats such as a typical bass or flats boat Generally speaking it can hold position in currents of 2 knots or wind speeds up to about 30 knots assuming wave action Is not too great Boats larger than 24 feet or those with larger draft or windage may require higher amounts of thrust to maintain position under adverse co
6. than 23 00 volts This function will stop all thrust and steering operation and use the precision voltage reference of the system to determine the battery s remaining charge State of charge levels are based on voltage to charge references for ideal lead acid batteries from leading battery manufacturers www watersnake com au 11 12 LAURENAN ELECTRIC MoT ors MODES OF OPERATION MANUAL MODE To place the motor in Manual Mode press the button with the symbol on the wireless fob The unit will emit 1 beep to indicate that it has entered Manual Mode 4 b K In the MANUAL MODE the GPSmart motor system behaves v much like a conventional trolling motor by allowing the user to control the direction and thrust level using the directional controls on the wireless fob THRUST The motor is equipped with 10 forward and 10 reverse thrust levels Momentarily pressing the Up Arrow or Down Arrow buttons will increment the thrust level accordingly Holding the Up Arrow or Down Arrow buttons will cause the thrust level to ramp until the maximum level is reached or the button is released It will take 2 5 seconds for the system to ramp from 0 to 100 thrust or vice versa The motor will emit 1 beep when it reaches qO 100 forward thrust 0 thrust or 100 reverse thrust STEERING 4 lt b Pressing the Left Arrow or Right Arrow buttons will h cause the motor to turn left or right respective
7. the new fob will be learned by your system and is ready to be used N Warning do not attempt to stow the unit until it has stopped beeping ERASING ALL FOBS FROM MEMORY 1 Power the unit up in the stowed position 2 Deploy stow and re deploy the unit prior to pressing any fob buttons 3 The unit will begin beeping indicating that it is ready to learn new wireless controls from the step above 4 Within 20 seconds while the system is still beeping stow and deploy the system once more 9 The system will sound a long beep indicating that all fobs have been erased frommemory If this step is being performed because of concerns about a defective fob it will be necessary to remove the batteries from all fobs in question prior to completing this process www watersnake com au 21 WATIERSINAKES ELECTRIC MoT ors MAINTENANCE 8 STORAGE It is recommended that the following steps be taken after each use Adhering to these recommendations can greatly increase the life of the unit Failure to properly maintain the unit may void the warranty and can result in system damage personal injury and property damage e Rinse off any salt water deposits and wipe the motor down with a clean soft cloth Do not use a pressure washer to clean the unit e Check that the propeller is clear of any fishing line or weeds e Use the prop nut tool to ensure the prop nut Is properly secured e Lubricate all moving parts with a non aero
8. LLATION The Watersnake GPSmart motor requires 24 Volts DC to Operate Typically 2 12V deep cycle marine batteries are used A A A A Batteries produce and contain harmful materials that may result in personal injury and or property damage if improperly used Refer to your battery manufacturer s guidelines for charging discharging storage and care instructions Be sure all switches circuit breakers are in the OFF position and fuses are removed when making battery connections Failure to do so may result In personal injury and or property damage DO NOT connect the trolling motor batteries to any other device including the main outboard engine Verify that all conductors and connectors are rated for at least 50 Amperes and 24VDC All circuits MUST be protected using a 50A fuse or circuit breaker in series with the positive lead Failure to do so may result in personal injury and or property damage BASIC INSTALLATION Your Watersnake GPSmart system is provided with a factory installed power cord with 5 16 ring terminals for connection to breaker battery terminals or power lugs Please note that it is mandatory to install a fuse or breaker protection for the system circuit This protection should be rated for 50A 24V If you boat is already wired with a 24 volt power system with appropriate circuit protection simply connect the white wire to the positive lug and the black wire to the negative lug Should you boat use tr
9. The GPSmart motor integrates a quick release bracket mechanism Attach the bracket to the bow of the boat taking care to ensure it is on the centreline of the boat and placed forward enough so that when the motor is attached the shaft of the motor is not making contact with the boats gunwale rubber With the bracket in position mark the holes for drilling ensuring as you do that the bow area below the mounting location is clear and accessible Attach the bottom Nylon bracket to the bow using the stainless steel bolts nuts and washers provided It is important when doing this work that the boat is level 1 Top plate Attach to motor mount 1 Attach top plate to the bracket 2 Attach bottom plate to the boat 3 Position motor bracket over top of bottom plate 4 Push steel locking wire into locking plate 2 Bottom plate Attach to boat Locking wire Plates fitted and locked together PLEASE NOTE Watersnake Distribution accepts no liability for injury or damage caused while drilling mounting this motor Please wear appropriate protective clothing and eyewear face shield Watersnake OGI SMART DEPLOYING THE UNIT Loosen the depth adjustment collar and slide it up the shaft to a position that will give the desired motor depth Firmly hand tighten the adjustment knob to secure the collar Step on the Tilt Lock Lever and slide the motor forward until the lower unit is clear of the storage cradle Carefully tilt t
10. ULD RATED FOR MARINE WSE Watersnake OGI SMART MODES OF OPERATION POWERING UP THE MOTOR The motor is able to function in Manual Mode immediately when powered up and deployed Anchor Mode and Track Mode will be will take 30 seconds before it becomes available after it has received a GPS fix 4 The motor will sound 1 beep to let you know that it is powered up The motor will sound 4 rapid beeps to let you 4 know that it has acquired a GPS fix GPS accuracy will continue to improve for several minutes after being powered up It is suggested that you power up the GPSmart early in the trip so that it will achieve maximum accuracy before being used The motor is equipped with a Tilt sensor that prevents the propeller from running in the stowed position BATTERY LEVEL INDICATOR Press and hold the off button on the remote fob for 5 seconds to check the state of charge of the system batteries N P V C The motor will sound between one and five beeps which indicates the amount of power still left in the battery 5 beeps greater than 95 charge greater than 25 20 volts 4 beeps between 80 and 95 charge between 24 84 volts and 25 20 volts 3 beeps between 6096 and 8096 charge between 24 40 volts and 24 84 volts 2 beeps between 40 and 60 charge between 23 80 volts and 24 40 volts 1 beep between 20 and 40 charge between 23 00 volts and 23 80 volts 1 growl less than 20 charge less
11. WATERSNAKE e ec Tr a ae rec ANAANANININ SI NIV T BOW MOUNT GPS ELECTRIC MOTOR OWNERS MANUAL Includes quick release mount and 2 fobs Anchor locations can be adjusted in precise 5 ft increments j Automatic compensation for wind waves and cross current CONTENTS 3 Specifications 4 General Information D Motor Drawing Features 6 Installation 7 Installation 8 Installation 7 Installation 11 Modes of Operation 12 Modes of Operation 13 Modes of Operation 14 Modes of Operation 15 Modes of Operation 16 Modes of Operation 17 Modes of Operation 18 Calibrations 19 Calibrations 20 Wireless Control FOB 21 Wireless Control FOB 22 Maintenance 23 Maintenance 24 Spare Parts 29 Accessories 2j Notes LAURENAN ELECTRIC MoT ors Motor to Boat Deploying Stowing Propeller Electrical Powering up Motor Battery Level Indicator Thrust Steering Modes Anchor Adjusting Anchor Storing Anchor Modes Re call Anchor Site Re call last Anchor Site Tracking Mode Adjust Tracking Speed Adjust Tracking Course Route Mode Storing Route Mode Re calling Centering Manual Compass Calibration Automatic Compass Calibration Replacing battery Programming new Wireless FOB Erasing FOB memory Storage Troubleshooting Guide Schematic Watersnake Motor Accessories Watersnake GIP SMART WATERSNAKE ELECTRIC MOTORS Congratulations and welcome to a world of silent motoring Powerful yet
12. eller Kit is suitable for 2816 30lb and 34lb motors The 3 Bladed Medium Propeller Kit is suitable for all 44lb and 54lb motors The 3 Bladed Large Propeller Kit is suitable for all 70lb 8016 and 105lb motors Jarvis Marine WATERSNAKE Jarvis SS Marine WATERSNAKE 3 Blade Trolling Motor Replacemy Propeller Jarvis Marine WATERSNAKE 2 Blade Trollin includes Prop Motor Replace Prop Nut amp Pin ler 55501 Large 3 Blade 55130 Prop 700 1051 3 Blade Prop 55131 4416 5416 2 Blade Prop 55500 28 3410 2 Blade Mini Prop 1810 2416 lt _ Jarvis WATERSNAKE Replacement Propeller Nut Accessory Kit Watersnake Telescopic Extendable Motor Handle The Watersnake Telescopic Handle can extend to 24 and will fit most tiller handles 55507 5 SEIWD9S ED 1409537710 Watersnake Propeller Accessory Kit This kit is very handy and we suggest you keep one at all times Consists of a propeller nut wrench propeller nut and shear pins 55182 www watersnake com au 25 26 Watersnake Trolling Motor Connectors Watersnake Motor Connector Plugs makes it very quick and simple to remove and replace your motor from the boat as well as providing a better connection to your power source Available 12v plug f 1 m 4 T s ES Watersnake Replacement Fuse Replacement 50 Amp luse to suit a Watersnake Fuse Kit
13. gged in Using a volt meter determine the positive 24 volt and ground negative terminals on the socket and plug Following the instructions provided with the plug connect the white power wire to the positive 24 volt terminal and the black power wire to the negative terminal When complete reinstall any fuses or turn on your circuit breaker and insert the plug into the socket At this point you should hear the system beep Indicating that it is getting power COMPLETE ELECTRICAL INSTALLATION If your boat is not already equipped with 24 volt battery power system it will be necessary to install one technicians We recommend that you contact an authorized installer to complete This process is of moderate difficulty and should only be attempted by experienced this process for you A 24 volt trolling motor battery system will generally consist of two 12 volt deep cycle batteries 6 or larger for long runs power conductors a 24v 50A rated circuit breaker a 24v 50A rated receptacle and optionally a permanently installed 24v battery charger as per the following wiring schematic If you plan to attempt a complete installation yourself please feel free to contact your nearest Watersnake dealer for additional guidance and information il 504 24Y RATED Be pd Inc TERMINAL BLOCK OR MOERS SEEN TROLLING MOTOR PLUG CONDUCTORS SHOULD BE AT LEAST AUNG LARGER CONDUCTORS BE REQUIRED FOR LONG RUNS CONDUCTORS SHO
14. he recall command The motor will beep a tune to indicate that the boat is arriving at the end of the recorded route When recalling a stored route if you hold the buttons too long you will over write that existing route memory location with the boat s present location erasing it and begin recording a new route The motor will calculate a beeline to the nearest point on the route Make sure there are no obstructions between you and the route prior to recalling it www watersnake com au 17 18 AWTS ALAS ELECTRIC MoT ors CALIBRATIONS CENTERING CALIBRATION Note This procedure is required and is normally only completed once at the time of the installation It should also be performed every time the system Is transferred to another boat or after a compass calibration 1 Power up the system and deploy using the depth collar to adjust the height so that the motor can steer without any obstructions 2 Press the M button to enter Manual Mode Please note that the system is in an operational mode Stay a safe distance away from the propeller to avoid injury 3 Using the left and right arrows or manually rotating the head of the thruster steer the unit so that it is aligned with the keel of the boat pointing straight ahead with the propeller facing the stern of the boat 4 Press and hold the up and down arrow simultaneously for 5 seconds until the system beeps The system will return to Manual Mode
15. he unit forward and lower the motor until the depth adjustment collar is engaged with the steering bosses The Tilt Lock Lever can be released as soon as the motor begins to tilt Once the unit is fully deployed verify that the lever has fully returned to its up and locked position STOWING THE UNIT Step on the Tilt Lock Lever Grasping the head of the unit pull it up and then back until the lower unit rests securely in the storage cradle Release the Tilt Lock Lever and verify that it returns fully to its up and locked position Slide the depth adjustment collar down until it is in contact with the steering bosses then very firmly hand tighten the adjustment knob to secure the unit Done properly the unit cannot deploy Warning Failure to secure the unit with the depth adjustment collar when AN stowed can result in accidental deployment during extremely rough pounding seas which will not be covered by the warranty www watersnake com au 7 AWTS ALAS ELECTRIC MoT ors ATTACHING THE PROPELLER Before doing anything with the propeller ensure the cables to the battery are disconnected 1 Place shear pin in shaft as shown 2 Align the propeller against the shear pin on the shaft there is a groove on the back of the propeller which the shear pin needs to slot into and then tighten the propeller nut securely Propeller Nut Propeller Shaft 2 Propeller 8 Watersnake GIP SMART ELECTRICAL INSTA
16. ibution Pty Ltd 2013 Watersnake Distribution Pty Ltd All Rights Reserved Specifications are subject to change without notice
17. ions nearby docks pilings other boats etc and that the water is fairly calm 2 Power up the system and deploy it using the depth collar to adjust the height so that the motor can steer without any obstructions 3 Press the M button to enter Manual Mode Please note that the system is in an operational mode Stay a safe distance away from the propeller to avoid injury 4 Using the left and right arrow buttons steer the unit so that it is aligned with the keel of the boat pointing straight ahead with the propeller facing the stern of the boat 5 While holding down on the Manual M button press and hold on the Anchor A button for 5 seconds until the system beeps 6 The motor will now automatically steer to the right and ramp up the thrust causing the boat to begin rotating The boat will complete 2 full rotations and then the system will beep to indicate that the calibration is complete 7 The system will return to Manual Mode 8 It is required that the Centering Calibration is now performed www watersnake com au 19 20 JWATEFRSNAKEs ELECTRIC MoT ors REPLACING A FOB BATTERY The batteries in the wireless FOB should be capable of lasting a full fishing season or longer under normal usage conditions If your system is powered up yet fails to respond to a FOB or if you noticed decreased wireless range try replacing the battery 1 Using a 1 phillips screwdriver remove the two screws on the back of the fob 2
18. ly The u steering travel is limited to avoid wrapping up the motors power cord Watersnake GIP SMART ANCHOR MODE To place the motor in Anchor Mode press the button with the symbol on the wireless fob The motor will instantly lock in the anchor coordinates and begin maintaining position The motor will emit 1 beep to indicate C that it has entered Anchor Mode 4 gt The motor will emit a and w A qO two growls then exit this mode if there is no GPS fix The Anchor Mode automatically controls the steering and thruster speed to maintain the position of the boat s bow acting as a Virtual Anchor It is recommended that the boat be slowed or stopped prior to anchoring to minimize any overshoot ADJUSTING THE ANCHOR LOCATION JOGGING a Pressing any of the directional controls on the wireless fob D Up Down Left or Right moves the Anchor Location in SA precise 5 foot 1 52 increments relative to the boat s heading For example pressing the Right Arrow once moves the Anchor Location 5 feet 1 52 to the right of the boat s bow C The motor will emit 1 beep for each increment the Anchor location is moved The embedded system computer will be operating the trolling motor causing the bow of the boat to move as needed to maintain its location in this mode Unexpected movement of the boat may tend to unbalance you Be cautiou
19. nditions such as high wind or current Under fair weather conditions the system can generally be expected to perform reasonably well on larger boats Installation on boats smaller than 16 feet or those of lighter weight may result in overly aggressive movements In extreme cases this could lead to injury even death It is recommended that a trained technician install the Watersnake GPSMART Motor Improper installation can lead to poor performance injury or even death It is the responsibility of the installer to verify proper installation DO NOT connect the Waternsnake GPS motor to a power source until installation is completed The Waternsnake GPS motor utilizes sensors which will likely be affected by nearby magnetic fields DO NOT install unit with or near anything that produces a magnetic field steel magnets etc gt P gt P Watersnake 00000000 e a SIP SMART s ss Remote control unit N o Depth adjustment collar oN Handle MATEHONARE Integrated quick release bracket Composite YW shaft Motor Assembly unit www watersnake com au 5 JWATERSNAKESs ELEC TJ TIC MoT ors It is recommended that you read these assembly instructions prior to installing your Watersnake GPSMART Motor Improper installation can lead to poor performance or injury It is the responsibility of the installer to verify proper installation ATTACHING THE MOTOR TO THE BOAT
20. nual Mode Otherwise D the unit will gradually ramp to 40 forward speed to maintain the track Pressing the Up Arrow button A increases the thruster s forward speed Down Arrow button decreases the thruster s forward speed Reverse operation is disabled in this mode The motor will beep when the thruster reaches q 100 forward speed when it is stopped ADJUSTING THE TRACK COURSE The Track Course may be adjusted in precise 9 degree increments by pressing the Left or Right Arrow buttons on the wireless fob The motor will emit 1 beep each 4 time the track heading Is changed In this mode the steering is automatic but the thrust level is user selected In extreme wind or current it is necessary for the user to select a speed setting with adequate thrust to overcome the disturbances and remain on track www watersnake com au 15 ELECTRIC MoT ors ROUTE MODE STORING OR OVER WRITING A ROUTE From any mode while holding down the or button press and hold a directional button for 5 seconds The buttons can then be released and the motor will now the function corresponding OR to the button you selected or exe The motor is now recording your route The motor will emit a 1 second beep to q indicate that the route is being recorded You can now navigate along your desired course a switching a
21. olling motor plug not have a 24 volt trolling motor circuit please refer to additional instructions below or contact an approved system installer PLUG INSTALLATION If your boat is already wired with a 24 volt trolling motor battery system it may be necessary to install a plug on the end of the main power conductor in order to work with your boat A The following process is of moderate difficulty Should you not feel comfortable performing the steps listed below we recommend that you contact an authorized installer to complete this process for you There are many different plugs on the market but generally it is possible to obtain the appropriate plug from your local boating supply store Please make sure that the plug you install is rated for 50A 24V Should you have difficulty locating the appropriate plug please contact your nearest Watersnake dealer and we will do our best to assist you www watersnake com au 9 10 IWATIERSNAKES ELECTRIC MOT ors Once the appropriate plug is obtained it will need to be installed on the power cord Depending on the location of the socket relative to your system it may be appropriate to trim the main power conductor to a shorter length If shortening the power cable be sure to leave adequate length to complete the connection to the plug and allow for the plug to be inserted with a small amount of slack remaining Generally you should have 6 to 12 of slack in the cable when plu
22. s steer the unit so that it is aligned with the keel of the boat pointing straight ahead with the propeller facing the stern of the boat 5 Using another means of propulsion main engine paddle etc begin to continuously rotate the boat in a tight circle at a rate of one full revolution every 20 30 seconds 6 While holding down on the Manual M button press and hold on the Track T button for 5 seconds until the system beeps 7 After the boat has completed 2 full revolutions it will beep to indicate that the calibration is now complete 8 The system will return to Manual Mode The rotation may now be stopped 9 It is required that the Centering Calibration is now performed COMPASS AUTO CALIBRATION Optional Note This procedure is provided as an alternative to the Compass Manual Calibration for situations where external means of propulsion i e outboard engine or paddle are not available Generally speaking the Compass Manual Calibration will provide a more accurate correction and is preferred Performing a compass calibration procedure is recommended as part of the installation process to improve the accuracy of the GPSmart motor It will account for magnetic errors that can occur if the system is mounted close to other metallic objects i e cleats steel fasteners etc which may cause the system functions to misbehave 1 The boat must be in the water to perform this calibration Make sure that there are no obstruct
23. s until you have become familiar with the system dynamics STORING OR OVERWRITING AN ANCHOR SITE From any mode while holding down the button press and hold a directional button for 5 seconds The buttons can then be released and your boat will be anchored at this newly recorded site The motor will emit a 1 second beep to 4 indicate that the anchor site has been successfully saved www watersnake com au 13 14 JWATEFRSNAKEs ELECTRIC MoT ors RECALLING A STORED ANCHOR SITE From any mode while holding down the button press and release the appropriate directional button The button can then be released and your boat will navigate In a straight line directly to that location and anchor at the selected previously recorded site The motor will beep a tune multiple consecutive beeps to indicate that the anchor site has been successfully retrieved The motor will emit two growls and exit if the memory location is empty or the boat is not within 1 mile of a memorized location When recalling a stored anchor site if you hold the buttons for more than 5 seconds you will over write that existing memory location with the boat s present location erasing it The system will calculate a beeline to the selected anchor site Make sure there are no obstructions between you and the anchor site prior to recalling a location RECALLING LAST ANCHOR SITE From any mode
24. sol lubricant e Clean battery terminals regularly and check for loose terminal nuts e Store in a well ventilated dry area e Do not leave the motor outside in the elements especially in cold winter and or saltwater environments Long exposure to sub zero temperature will reduce the strength of the permanent magnets of the motor and result in reduced thrust e Never use chemicals alcohol solvents and acids on any of the system components e Use a Vinyl UV protector periodically on the power cables to avoid excessive sun damage e Periodically check for loose connections and or excessive corrosion is ready to be used Watersnake GIP SMART TROUBELSHOOTING QUICK REFERENCE GUIDE MOTOR IS SHAKING LOSS OF SPEED SYSTEM DOES NOT RESPOND TO WIRELESS COMMANDS SYSTEM WILL NOT ANCHOR OR TRACK AFTER SELECTING A MODE SYSTEM BEEPS TWICE AND THEN DOES NOTHING BATTERY DRAINS e Check for line or weed fouling of the propeller e Check Prop and Prop Nut e Check to see if propeller shaft is bent e Check battery condition Recharge and test for a bad cell e Check battery connections for corrosion e The power wiring from the battery to the motor may be too small Use 6 AWG e Verify that unit is locked in the deployed position e Cycle power off amp back on e Replace battery in wireless fob e Allow at least 1 minute for system to acquire a GPS fix Listen for 4 beeps indicating good GPS signal e Make
25. sure that nothing Is blocking the sky view of the GPS antenna e Battery voltage is low e Check all connections e Recharge battery and test for a bad cell e A drain of approximately 100 milliamps will be imposed on the system batteries If powered up when not in use e Always unplug the system when not In use The above reference is included to assist you in troubleshooting some basic issues that you might encounter At any time should you have a question or concern about the function of your GPSmart Motor please feel free to contact your nearest Watersnake dealer www watersnake com au 29 24 WATIERSINAKES ELECTRIC MoT ors S 2 lt Z CX LTLSS 0 C8v 00I N T 9 9 N09 08WCAS Suryo 1940 d 1940 UO011 2198 me 5 wW e et c Hn Q e er Wi IWH XV 8c IWH XV OOI N s Wa Nu 4 T4H pieoqpeop 80H SSOLOITM cv smt IS AH SWW IC guu luy Sd Watersnake IA AH SWM CC 8 0IgW SWW c pieogiouioR WATERSNAKE MOTOR ACCESSORIES SOLD SEPERATLY SEE YOU NEAREST DEALER FOR MORE INFORMATION Watersnake Propeller Kits sold Separately Watersnake Propeller kits contain a propeller nut and shear pins It is recommended you keep a Spare propeller on your boat at all times The Mini 2 Bladed Kit is suitable for the T 18 and 24 motors The 2 Bladed Prop
26. t will between manual and track modes 4 2 gt The recording will terminate when you press OR or A one 9x6 The motor will emit a 1 second beep O to indicate that the route has been e successfully saved Should you wish to record an anchor site using the or T memory these locations simply hit OFF or as soon as the path begins to record thus recording a path of zero length A route can also be recorded at higher speeds with the system in the stowed position Simply use the route storing procedure above and the system will accurately record your route at speeds of up to 60 knots For safety the thruster and steering motors will be disabled as long as the system is in the stowed position Watersnake GIP SMART ROUTE MODE RECALLING A STORED ROUTE From any mode while holding down the or button press and release the appropriate directional 4 a gt button The motor will beep tune O multiple consecutive beeps to indicate that the route has been successfully retrieved qO The motor will emit two growls and exit if the memory location is empty or the boat is not within 1 mile of a point on the route The motor will navigate directly to the nearest point on the route and then travel to the most distant end anchoring when it arrives At any time while retracing a route you can reverse the direction of travel by simply repeating t
Download Pdf Manuals
Related Search