Manual AEC-6877
Contents
1. 1 LOU 5 Chapter 2 Hardware Installation 2 9 Embedded Controller AEC 6877 Chapter AMI BIOS Setup Chapter 3 AMI BIOS Setup 3 1 Embedded Controller AEC 6877 3 1 System Test and lnitialization These routines test and initialize board hardware If the routines encounter an error during the tests you will either hear a few short beeps or see an error message on the screen There are two kinds of errors fatal and non fatal The system can usually continue the boot up sequence with non fatal errors System configuration verification These routines check the current system configuration stored in the CMOS memory and BIOS NVRAM If system configuration is not found or system configuration data error is detected system will load optimized default and re boot with this default system configuration automatically There are four situations in which you will need to setup system configuration 1 You are starting your system for the first time 2 You have changed the hardware attached to your system 3 The system configuration is reset by Clear CMOS jumper 4 The CMOS memor2. Im TT ki n VII Hg P UM o ET 1 T Chapter 2 Hardware Installation 2 2 Embedded Front side Controller AEC 6877 d 2 A n 1 NS 5 sw T 5 1 T ja pe Rear side N D qan Lane i aL IET E USB meti x tit oct kl on Chapter 2 Hardware Installation 2 3 l Embedded Controller AEC 6877 2 2 COM1 COM TX RX LED CN2 Pin Signal Pin Signal 1 45V 2 GND 3 TX LED COM 4 TX LED 1 5 RX LED COM1 6 RX LED 1 7 COM2 RS232 PWR 8 GND 9 TX LED COM2 10 TX LED COM2 11 RX LED COM2 12 RX LED COM2 13 COM2 RS485 PWR 14 COM2 RS422 PWR Note The COM port cannot support baud rate at 115200 since the hardware limitation of the motherboard EMB QM77 2 3 RS 232 Box Header COM 1 Pin Signal Pin Signal 1 DCD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI 10 2 4 USB Box Header USB1 USB3 Pin Si
3. Serial Port Disabled Enabled Default Enable or Disable Serial Port COM Change Settings Auto Default I0 3F8h IRQ 3 4 IO 2F8h IRQ 3 4 IO 3E8h IRQ 3 4 IO 2E8h IRQ 3 4 Select an optimal setting for Super IO device Device Mode RS 232 Default RS 422 RS 485 Change the Serial Port mode Select lt RS 232 gt or lt RS 422 gt or lt RS 485 gt mode Chapter 3 AMI BIOS Setup 3 19 AEC 6877 H W Monitor Aptio Setup Utility Copyright C 2011 American Megatrends Inc CPU Fani Control Disabled Chapter 3 AMI BIOS Setup 3 20 AEC 6877 Setup submenu Chipset Aptio Setup Utility Copyright C 2011 American Megatrends Inc gt PCH IO Configuration Chapter 3 AMI BIOS Setup 3 21 PCH IO Configuration AEC 6877 Aptio Setup Utilitu Copyright C 2011 American Megatrends Inc Power Mode Options Summary RTX Tupe Power Mode ATX Type Default AT Type Select power supply mode Restore AC Power Power off Loss Power on Last State Default Select AC power state when power is re appl power up after restore AC power if this item set to Notice The system will ied after a power failure last state and shuts down via iAMT remote control PCH LAN Controller Enabled Default Disabled Enable or disable onboard NIC Wake on LAN Enabled Default Disabled
4. Enable or disable integrated LAN to wake the system The Wake On LAN cannot be disabled if ME is on at Sx state Chapter 3 AMI BIOS Setup 3 22 Embedded Controller AEC 6877 Deep S5 Disabled Default Enabled Enabled Disabled Deep S5 Note When Deep S5 is enabled Intel amp AMT and Wake On PCH LAN functions are not available In system shut down Mini PCle Speed Gen1 Gen2 Default Select Mini PCI Express port speed Chapter 3 AMI BIOS Setup 3 23 6877 System Agent SA Configuration Aptio Setup Utilitu Copyright C 2011 American Megatrends Inc Enabled Options Summary VT d Disabled Enabled Default Check to enable VT d function on MCH PEGO Gen X Auto Default Gent Gen2 Gen3 Configure PEGO B0 D1 F0 Gen1 Gen3 Graphics Config Graphics Settings Configuration Chapter 3 AMI BIOS Setup 3 24 AEC 6877 Graphics Configuration Aptio Setup Utilitu Copyright C 2011 American Megatrends Inc Primary Display Auto Options Summary Primary Display Auto Default IGfx PEG Select which of IGFX PEG PCI Graphics device should be Primary Display Or select SG for Switchable Gfx Internal Graphics Auto Default Disabled Enabled Keep IGD enabled based on the setup options DVMT Pre Allocated 0 32M 64M Default Chapter 3 AMI
5. AEC 6877 Hard Drives BBS Priorities Aptio Setup Utility Copyright C 2011 American Megatrends Inc Boot Option 1 Skumedi USB3_Pen_D Chapter 3 AMI BIOS Setup 3 29 6877 Submenu Security Aptio Setup Utilitu Copyright C 2011 American Megatrends Inc Administrator Password Change User Supervisor Password You can install a Supervisor password and if you install a supervisor password you can then install a user password A user password does not provide access to many of the features in the Setup utility If you highlight these items and press Enter a dialog box appears which lets you enter a password You can enter no more than six letters or numbers Press Enter after you have typed in the password second dialog box asks you to retype the password for confirmation Press Enter after you have retyped it correctly The password is required at boot time or when the user enters the Setup utility Removing the Password Highlight this item and type in the current password At the next dialog box press Enter to disable password protection Chapter 3 AMI BIOS Setup 3 30 AEC 6877 Setup submenu Exit Save Changes and Reset Chapter 3 AMI BIOS Setup 3 31 Embedded Controller AEC 6877 Chapter Driver Installation Chapter 4 Driver Installation 4 1 Embedded Controller AEC 6877 The AEC 6877 comes with an AutoRun DVD ROM that contains all drivers and utilitie
6. Raid Driver F6 Floppy x86 to Disk F6Readme e zn readme 78KB Appendix C RAID amp AHCI Settings C 12 AEC 6877 Step 3 The setting procedures BIOS Setup Menu A Advanced SATA Configuration gt SATA Configuration gt SATA Mode gt AHCI Mode SATA Mode HCI Mode Step 4 The setting procedures In BIOS Setup Menu B Boot gt Boot Option 1 gt DVD ROM Type Appendix C RAID amp AHCI Settings C 13 AEC 6877 Step 5 The setting procedures In BIOS Setup Menu C Save amp Exit gt Save Changes and Exit E tim uetam Step 6 Setup OS Setup is inspecting your computer s hardware configuration Appendix C RAID amp AHCI Settings C 14 Embedded Controller AEC 6877 Step 7 Press F6 Press F6 if you need to install a third party SCSI RAID driver Step 8 Choose S Specify Additional Device ENTER Continue Exit Appendix C RAID amp AHCI Settings C 15 Embedded Controller AEC 6877 Step 9 Choose Intel R 7 Series Chipset Family SATA AHCI Controller Step 10 It will show the model number you select and then press ENTER Appendix C RAID amp AHCI Settings C 16 AEC 6877 Step 11 Setup is loading files Setup is loading files Compaq Dri Appendix C RAID amp AHCI Settings C 17
7. ISA 000000061 97 gM 15 000000062 98 15 000000063 99 ISA 000000064 100 ISA 000000065 101 ISA 000000066 102 ISA 000000067 103 JM ISA 000000068 104 15 000000069 105 ISA 0 0000006A 106 ISA 0 00000068 107 ISA 0 0000006 108 15 0 00000060 109 JM ISA 0 0000006 110 ISA 0x0000006F 111 ISA 000000070 112 ISA 0x00000071 113 ji ISA 0x00000072 114 ISA 000000073 115 Mi ISA 000000074 116 ISA 000000075 117 Wa ISA 000000076 118 ISA 000000077 119 Wa ISA 0x00000078 120 System timer Standard PS 2 Keyboard Communications Port COM2 Communications Port COM1 System CMOS real time clock Microsoft PS 2 Mouse Numeric data processor Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant
8. Wa 154 000000097 151 ISA 0x00000098 152 15 0x00000099 153 318 ISA 0x0000009A 154 ISA 0x0000009B 155 ISA 0x0000009C 156 1 SA 0x0000009D 157 ISA 0x0000009E 158 ISA 0x0000009F 159 ISA 0x000000A0 160 Wa ISA 0 000000 1 161 ISA 0x000000A2 162 Wa ISA 000000043 163 ISA 0x000000A4 164 ISA 0x000000A5 165 ISA 0x000000A6 166 ISA 0x000000A7 167 Mi 154 0500000048 168 ISA 0x000000A9 169 JW ISA 0x000000AA 170 ISA 0x00000079 121 Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Mic
9. 2 this device must accept any interference received including interference that may cause undesired operation Caution There is a danger of explosion if the battery is incorrectly replaced Replace only with the same or equivalent type recommended by the manufacturer Dispose of used batteries according to the manufacturer s instructions and your local government s recycling or disposal directives Embedded Controller AEC 6877 Below Table for China RoHS Requirements Pin EUR SER EW RENTUR AAEON Boxer Industrial System ABA SEI R ER J 4 LAA Pb Hg Cd Cr VI BK PBDE EN A Fa ER IK x ARTE x BAR AM F56 x O O O O HP Rh Be A x 5A Ti dt O x SH AZA ZANFAN A PA ESE SJ T 11363 2006 k I F X Aem BA dI BP EVER AE YAMA rH BJ Sr ROGER tH SJ T 11363 2006 x YE XL FE EK fi eee vi Embedded Controller AEC 6877 Contents Chapter 1 General Information 1 1 2 72 1 4 1 2 2 yasa t E 1 4 1 3 1 5 Chapter 2 Hardware Installation 2 DIMENSION RR ete 2 2 2 2 COM1 COM2 TX RX LED CN2 2 4 2 3 RS 2
10. Inc SATA Controller s Enabled Options Summary SATA Enabled Default Controller s Disabled Enable or disable SATA Device SATA Mode IDE Default Selection AHCI RAID Determines how SATA controller s operate Chapter 3 AMI BIOS Setup 3 9 6877 IDE Configuration AHCI Aptio Setup Utility Copyright C 2011 American Megatrends Inc SATA Mode Selection AHCI Options Summary SATA Controller s Disabled Enabled Default Enable or Disable SATA Port SATA Mode Selection IDE AHCI Selected RAID Determines how SATA controller s operate Port 0 Port 4 Disable Enabled Enabled Enable or Disable SATA Port Serial ATA Port Hot Plug Disable Default Port 0 Port 4 Enabled Designates this port as Hot Pluggable Chapter 3 AMI BIOS Setup 3 10 6877 IDE Configuration RAID Aptio Setup Utility Copyright C 2011 American Megatrends Inc SATA Mode Selection RAID Options Summary SATA Controller s Disabled Enabled Default Enable or Disable SATA Port SATA Mode Selection IDE AHCI RAID Selected Determines how SATA controller s operate Port 0 Port 4 Disable Enabled Enabled Enable or Disable SATA Port Serial ATA Port Hot Plug Disable Default Port 0 Port 4 Enabled Designates this port as Hot Pluggable Chapter 3 AMI BIOS Setup 3 11 AEC 6877 In
11. b 38 Local Users and Group a gt Performance me idows system32 DRIVERS serenum 1 Exc sys 8 Device Manager E d CAWindows system32ADRIVERS serial 5 5 4 amp Storage Disk Management gt Services and Applications Communications Port COM4 Driver Provider Windows R Win 7 DDK provider 6 1 7600 16385 built by WinDDK Microsoft Corporation All rights reserved Not digitally signed 2 11 PM 10 20 2011 a Chapter 4 Driver Installation 4 7 Embedded Controller AEC 6877 Appendix Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A 1 Embedded Controller AEC 6877 A 1 Programming AEC 6877 utilizes ITE IT8728 chipset as its watchdog timer controller Below are the procedures to complete its configuration and the AAEON intial watchdog timer program is also attached based on which you can develop customized program to fit your application Configuring Sequence Description After the hardware reset or power on reset the ITE 8728 enters the normal mode with all logical devices disabled except KBC The initial state enable bit of this logical device KBC is determined by the state of pin 121 DTR1 at the falling edge of the system reset during power on reset Hardware Reset Wait for key string pom write to 2Eh Any other I O transition
12. option ROM poration All Rig None defined Physical Disks Port Drive Model Serial FUJITSU MHZ2080B K680FT972B7HN 1 ST912882385 5NJ0SZ08 ress to enter Configuration Utility Step 8 Choose 1 Create RAID Volume Disks to Non RAID covery Volume Options DISK VOLUME INFORMATION RAID Volumes None defined Physical Disks Port Brive Model Serial Size Type Status Vol ID 8 FUJITSU MHZ2888B K58FT972B7HN 74 568 1 51912982388 54483298 111 768 Appendix RAID amp AHCI Settings C 5 Embedded Controller AEC 6877 Step 9 RAID Level gt RAIDO Stripe voluneo Capacity 149 1 GB Sync N A Create Volune HELP Choose the RAID level RAID 8 Stripes data performance RAID 1 Mirrors data redundancy Recovery Copies data between a master and a recovery disk Step 10 Choose Create Volume CREATE VOLUME MENU J Voluned RAIDO Stripe Select Disks Strip Size 128KB Capacity Syw Press ENTER to create the specified volume Appendix C RAID amp AHCI Settings C 6 Embedded Controller AEC 6877 Step 11 Choose Y CREATE UOLUME MENU Mane UoluneB RAID Level RAID Stripe Disks Select Disks Strip Size 128KB Capacity 149 1 GB Sync N A Press ENTER to create the specified volune 1 Create RAID Volune 3 Reset Disks to Non RAID 2 Delete RAID Volune Recovery Volume Options DISK UULuns inruKMATION J Level Strip Size Status B
13. 0 WDT Time out value 7 0 Appendix A Programming the Watchdog Timer A 5 Embedded Controller AEC 6877 A 2 ITE8728 Watchdog Timer Initial Program MODEL SMALL CODE Main CALL Enter Configuration mode CALL Check Chip mov cl 7 call Set Logic Device time setting mov cl 10 10 Sec dec al Watch Dog Setting Timer setting mov al cl mov cl 73h call Superio Set Reg Clear by keyboard or mouse interrupt mov al OfOh mov cl 71h call Superio Set Reg unit is second mov al OCOH mov cl 72h call Superio Set Reg Appendix A Programming the Watchdog Timer A 6 Embedded Controller AEC 6877 game port enable mov cl 9 call Set Logic Device Initial OK CALL Exit Configuration mode MOV AH 4Ch INT 21h Enter Configuration Mode PROC NEAR MOV SI WORD PTR CS Offset Cfg Port MOV DX 02Eh MOV CX 04h Init 1 MOV AL BYTE PTR CS SI OUT DX AL INC SI LOOP Init 1 RET Enter Configuration Mode ENDP Exit Configuration Mode PROC NEAR MOV AX 0202h CALL Write Configuration Data Appendix A Programming the Watchdog Timer A 7 Embedded Controller AEC 6877 RET Exit Configuration Mode ENDP Check Chip PROC NEAR MOV AL 20h CALL Read Configuration Data CMP AL 87h JNE Not Initial MOV AL 21h CALL Read Configuration Data CMP AL 12h JNE Not Initial Need Initial STC RET Not Initial CLC RET Check Chip ENDP Read Configuration Data PROC NEAR MOV DX WORD PTR CS Cfg Port 04h OUT DX AL A
14. 00000025 Programmable interrupt controller 398 00000028 00000029 Programmable interrupt controller 0000002C 00000020 Programmable interrupt controller 088 0000002 0000002F Motherboard resources 1 00000030 00000031 Programmable interrupt controller 088 00000034 00000035 Programmable interrupt controller 00000038 00000039 Programmable interrupt controller 9980 0000003C 00000030 Programmable interrupt controller 00000040 00000043 System timer 0880 00000044 0000005F Motherboard resources 0000004E 0000004F Motherboard resources 00000050 00000053 System timer zz 00000060 00000060 Standard PS 2 Keyboard ql 00000061 00000061 Motherboard resources 00000062 00000063 Motherboard resources 288 00000063 00000063 Motherboard resources 2 00000064 00000064 Standard PS 2 Keyboard 388 00000065 00000065 Motherboard resources 098 00000065 0000006F Motherboard resources 288 00000067 00000067 Motherboard resources 00000070 00000070 Motherboard resources 088 00000070 00000077 System CMOS real time clock 00000072 0000007F Motherboard resources 00000080 00000080 Motherboard resources 00000080 00000080 Motherboard resources 0880 00000081 00000091 Direct memory access controller 1X 00000084 00000086 Motherboard resources 00000088 00000088 Motherboard resources 00000
15. BIOS Setup 3 25 Embedded Controller AEC 6877 224M 256M 288M 320M 352M 384M 416M 448M 480M 512M Select DVMT 5 0 Pre Allocated Fixed Graphics Memory size used by the Internal Graphics Device DVMT Total Gfx Men 128M 256M MAX Default Select DVMT5 0 Total Graphic Memory size used by the Internal Graphics Device Chapter 3 AMI BIOS Setup 3 26 AEC 6877 Display Control Aptio Setup Utility Copyright C 2011 American Megatrends Inc Boot Display Select VBIOS Default Options Summary Boot Display Select VBIOS Default Default CRT DisplayPort 1 DVI DisplayPort 2 Select the Video Device during POST and DOS This has no effect if external graphics present Chapter 3 AMI BIOS Setup 3 27 6877 Setup submenu Boot Aptio Setup Utilitu Copyright C 2011 American Megatrends Inc ed ipset secur amp t Quiet Boot Enabled Options Summary Quiet Boot Disabled Enabled Default Enables or disables Quiet Boot option Launch 182579LM PXE Disabled Default OpROM Enabled Enable or Disable Legacy Boot Option for 182579LM Launch RTL8111E Disabled Default PXE OpROM Enabled Enable or Disable Legacy Boot Option for RTL8111E Boot options 4X Your storage disk devices Sets the system boot order Chapter 3 AMI BIOS Setup 3 28
16. Is the data 87h Y Check Pass key Y O write to 2Eh N Next Data Y ta Y Any other I O transition cycle N Last Da MB PnP Mode Appendix A Programming the Watchdog Timer A 2 Embedded Controller AEC 6877 There are three steps to complete the configuration setup 1 Enter the MB PnP Mode 2 Modify the data of configuration registers 3 Exit the MB PnP Mode Undesired result may occur if the MB PnP Mode is not exited normally 1 Enter the MB PnP Mode To enter the MB PnP Mode four special I O write operations are to be performed during Wait for Key state To ensure the initial state of the key check logic it is necessary to perform four write operations to the Special Address port 2EH Two different enter keys are provided to select configuration ports 2Eh 2Fh of the next step Address Port Data Port 87h 01h 55h 55h 2Eh 2Fh 2 Modify the Data of the Registers All configuration registers can be accessed after entering the MB PnP Mode Before accessing a selected register the content of Index 07h must be changed to the LDN to which the register belongs except some Global registers 3 Exit the MB PnP Mode Set bit 1 of the configure control register Index 02h to 1 to exit the MB PnP Mode Appendix A Programming the Watchdog Timer A 3 Embedded Controller AEC 6877 WatchDog Timer Configuration Registers LDN Index R W Reset Configuration Register or A
17. System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Appendix B I O Information B 5 ISA 0 0000007 122 ISA 0x0000007B 123 ISA 0x0000007C 124 ISA 0x0000007E 126 ISA 0x0000007F 127 ISA 0x00000080 128 ISA 000000081 129 15 0x00000082 130 JE 15 0 00000083 131 Wa ISA 000000084 132 Wa 154 0x00000085 133 15 0x00000086 134 15 0x00000087 135 JE ISA 0x00000088 136 1 ISA 0x00000089 137 1 ISA 0x0000008A 138 JE 15 0x0000008B 139 ISA 0x0000008C 140 ji ISA 0x0000008D 141 ISA 0x0000008E 142 88 ISA 0x0000008F 143 ISA 0x00000090 144 ISA 0x00000091 145 ISA 0x00000092 146 ISA 0x00000093 147 ISA 0x00000094 148 Wa 154 0400000095 149 15 000000096 150
18. select the OS folder your system is 2 Double click on patch bat file located in each OS folder Follow the instructions that the window shows The system will help you install the driver automatically Control Panel Home Make changes to your user account Manage your credentials 2 Create a password for your account Create a password reset disk a Change your picture 1 Link online IDs i Change your account name Administrator Manage your file encryption certificates Change your account type Configure advanced user Bese Manage another account Change my environment Change User Account Control settings variables Parental Controls 204 10 20 2011 9 te Chapter 4 Driver Installation 4 5 Family Safety User Accounts Make changes to your user acco Change your password Remove your password Change your picture Change your account name Change your account type Manage another account Change User Account Control settings al patch patch install di Getting Started e Windows Media Center Calculator Paint Sticky Notes Q Sniping Tool Remote Desktop Connection av Magnifier sj Solitaire AEC 6877 Choose when to be notified about changes to your computer User Account Control helps prevent potentially m programs from making changes E Never notify Never notify me when Programs try to install software o
19. 00000000 000D3FFF PCI bus 288 00004000 000D7FFF PCI bus JE 000D8000 000DBFFF PCI bus 098 000DC000 OOODFFFF PCI bus 000 0000 000E3FFF PCI bus ql 000 4000 000E7FFF PCI bus 20000000 201FFFFF System board 88 40004000 40004FFF System board 4A DFA00000 DFAOOFFF Motherboard resources 288 DFA00000 FEAFFFFF PCI bus E0000000 EFFFFFFF Intel R HD Graphics 4000 F0000000 FOOO3FFF Realtek PCIe Family Controller 3 F0000000 FOOFFFFF Intel R 7 Series C216 Chipset Family PCI Express Root Port 2 112 A F7800000 F7BFFFFF Intel R HD Graphics 4000 F7C00000 F7COOFFF Realtek PCIe Family Controller 3 088 F7COOOOO F7CFFFFF Intel R 7 Series C216 Chipset Family PCI Express Root Port 2 1 12 a F7D00000 F7D1FFFF Intel R 82579LM Gigabit Network Connection F7D20000 F7D2FFFF Intel R USB 3 0 eXtensible Host Controller 4M F7D30000 F7D33FFF High Definition Audio Controller 388 F7D35000 F7D350FF Intel R 7 Series C216 Chipset Family SMBus Host Controller 1E22 lt gt F7D36000 F7D367FF Intel R 7 Series Chipset Family SATA AHCI Controller F7D37000 F7D373FF Intel R 7 Series C216 Chipset Family USB Enhanced Host Controller 1E26 F7D38000 F7D383FF Intel R 7 Series C216 Chipset Family USB Enhanced Host Controller 12D F7D39000 F7D39FFF Intel R 82579LM Gigabit Network Connection 27 F7D3A000 F7D3AFFF In
20. 0017 23 PCI OxFFFFFFFS 8 PCI OxFFFFFFF9 7 9 PCDOxFFFFFFFA 6 PCI OxFFFFFFFB 5 lt gt PCI OxFFFFFFFC 4 PCI OxFFFFFFFD 3 PCI OxFFFFFFFE 2 Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System AEC 6877 Intel R 7 Series C216 Chipset Family SMBus Host Controller 1E22 Intel R 7 Series C216 Chipset Family USB Enhanced Host Controller 1E2D Intel R Management Engine Interface Intel R Active Management Technology SOL COM3 High Definition Audio Controller Intel R 7 Series C216 Chipset Family USB Enhanced Host Controller 1 26 Realtek PCIe GBE Family Controller 3 Intel R 82579LM Gigabit Network Connection Intel R USB 3 0 eXtensible Host Controller Intel R HD Graphics 4000 Intel R 7 Series Chipset Family SATA AHCI Controller Intel R 7 Series C216 Chipset Fami
21. 08C 0000008E Motherboard resources 4 00000090 0000009F Motherboard resources 00000092 00000092 Motherboard resources 00000093 0000009F Direct memory access controller 0880 000000A0 000000A1 Programmable interrupt controller 288 00000042 000000BF Motherboard resources 00000044 00000045 Programmable interrupt controller 388 00000048 00000049 Programmable interrupt controller 398 000000AC 000000AD Programmable interrupt controller 298 000000B0 00000081 Programmable interrupt controller 000000B2 00000083 Motherboard resources 1 00000084 00000085 Programmable interrupt controller 00000088 00000089 Programmable interrupt controller 000000BC 00000080 Programmable interrupt controller 088 0000000 000000DF Direct memory access controller Appendix B I O Information B 2 Embedded Controller AEC 6877 248 000000E0 000000EF Motherboard resources 000000F0 000000FF Numeric data processor 00000200 0000020F Motherboard resources 000002F8 000002FF Communications Port COM2 00000380 000003BB Intel R HD Graphics 4000 00000300 000003DF Intel R HD Graphics 4000 000003F8 000003FF Communications Port COM1 00000400 00000453 Motherboard resources 1W 00000454 00000457 Motherboard resources 00000458 0000047F Motherboard resources 388 00000400 00000401 Motherboard resour
22. 32 Box Header COM 1 2 4 2 4 USB Box Header USB1 USB3 2 4 2 5 HDD 2 2 5 2 6 CFast Card Installation 2 7 2 7 PCI Express Card Installation 2 8 2 8 Wallmount Bracket Installation 2 9 Chapter 3 AMI BIOS Setup 3 1 System Test and Initialization 3 2 3 2 AMI BIOS Setup sse 3 3 Chapter 4 Driver Installation 4 JiInstallatiori itid i kk kn pe iei 4 3 Appendix A Programming The Watchdog Timer A 1 Programming eene A 2 A 2 ITE8728 Watchdog Timer Initial Program A 6 vii Embedded Controller AEC 6877 Appendix I O Information B 1 Address Map B 2 B 2 Memory Address Map B 4 IRQ Mapping Chart B 5 4 DMA Channel Assignments B 7 Appendix C RAID amp AHCI Settings C 1 Setting C 2 C 2 Setting sas at G4 viii Embedded Controller AEC 6877 Chapter General Information Chapter 1 General Information 1 1 Embedded Controller AEC 6877 1 1 Introduction Due to the growing popularity from the IPC market the newest Boxe
23. Embedded Controller AEC 6877 AEC 6877 Fanless Embedded Controller Intel Core i7 i5 Celeron Processor with 2 Gigabit Ethernet 2 COM 4 USB3 0 2 DisplayPort 2 PCI or 1 PCI Express x4 DVI D CFast SATA 3 0Gb s AEC 6877 Manual 2nd Ed August 2013 Embedded Controller AEC 6877 Copyright Notice This document is copyrighted 2012 All rights are reserved The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice No part of this manual may be reproduced copied translated or transmitted in any form or by any means without the prior written permission of the original manufacturer Information provided in this manual is intended to be accurate and reliable However the original manufacturer assumes no responsibility for its use or for any infringements upon the rights of third parties that may result from its use The material in this document is for product information only and is subject to change without notice While reasonable efforts have been made in the preparation of this document to assure its accuracy AAEON assumes no liabilities resulting from errors or omissions in this document or from the use of the information contained herein AAEON reserves the right to make changes in the product design without notice to its users Embedded Controller AEC 6877 Acknowledgments e Award is a trademark of Award Software Internatio
24. M series e Indicator Front Power LED x 1 HDD active LED x 1 Power Requirement DC 9 30V with 3 pin terminal block e System Cooling Passive cooling e Mounting Wallmount Operating Temperature 32 F 122 F 0 C 50 C with airflow Storage Temperature 4 F 158 F 20 C 70 Storage Humidity 10 95 40 C non condensing Anti Vibration 5 g rms 5 500 Hz operation CFast 1 g rms 5 500 Hz operation HDD Anti Shock 20 G peak acceleration 11 msec duration HDD EMC Certification CE FCC Class A Dimension W x H x D 8 19 x 4 02 x 9 37 208mm x 102mm x 238mm Gross Weight 13 2 Ib 6 Kg OS Support Windows XP Embedded Windows XP Windows 7 Linux Fedora 10 Chapter 1 General Information 1 6 Chapter 1 General Information 1 7 Embedded Controller AEC 6877 Chapter Hardware Installation Chapter 2 Hardware Installation 2 1 Embedded Controller AEC 6877 2 1 Dimension
25. ces 388 00000400 00000401 Programmable interrupt controller 00000500 0000057F Motherboard resources 00000680 0000069F Motherboard resources 00000400 00000A1F Motherboard resources 00000A20 00000A2F Motherboard resources 00000A30 00000A3F Motherboard resources 00000000 0000FFFF PCI bus 0000164E 0000164F Motherboard resources 0000E000 0000E0FF Realtek PCIe GBE Family Controller 3 38 0000E000 0000EFFF Intel R 7 Series C216 Chipset Family PCI Express Root Port 2 1E12 0000F000 0000F03F Intel R HD Graphics 4000 0000F040 0000 05 Intel R 7 Series C216 Chipset Family SMBus Host Controller 1E22 10000 060 0000F07F Intel R 7 Series Chipset Family SATA AHCI Controller 0000F0A0 0000F0A3 Intel R 7 Series Chipset Family SATA AHCI Controller 10000 080 0000F0B7 Intel R 7 Series Chipset Family SATA AHCI Controller 10000 0 0 0000 0 3 Intel R 7 Series Chipset Family SATA AHCI Controller 10000 000 0000F0D7 Intel R 7 Series Chipset Family SATA AHCI Controller 0000FOEO 0000 0 7 Intel R Active Management Technology SOL COM3 0000 0000FFFF Motherboard resources ji OOOOFFFF 0000FFFF Motherboard resources Appendix B I O Information B 3 AEC 6877 B 2 Memory Address Map Memory BS 00040000 000BFFFF Intel R HD Graphics 4000 jE 00040000 000BFFFF PCI bus gl
26. ction Al 02H W N A Configure Control 07H 71H R W 00H WatchDog Timer Control Register 07H 72H R W OOH WatchDog Timer Configuration Regis ter 07H 73H R W 00H WatchDog Timer Time out Value Register Configure Control Indexz02h This register is write only Its values are not sticky that is to say a hardware reset will automatically clear the bits and does not require the software to clear them Bit Description 7 2 Reserved 1 Returns to the Wait for Key state This bit is used when the configuration sequence is completed 0 Resets all logical devices and restores configuration registers to their power on states Appendix A Programming the Watchdog Timer A 4 Embedded Controller AEC 6877 WatchDog Timer Control Register Indexz71h Default 00h Bit Description f WDT is reset upon a CIR interrupt 6 WDT is reset upon a KBC mouse interrupt 5 WDT is reset upon a KBC keyboard interrupt 4 WDT is reset upon a read or a write to the Game Port base address 3 2 Reserved 1 Force Time out This bit is self clearing 0 WDT Status 1 WDT value reaches 0 0 WDT value is not 0 WatchDog Timer Configuration Register Index 72h Default 00h Bit Description 7 WDT Time out value select 1 Second 0 Minute 6 WDT output through KRST pulse enable 5 4 Reserved 3 0 Select the interrupt level e for WDT WatchDog Timer Time out Value Register Index 73h Default 0Oh Bit Description 7
27. ed in dotNet Framwork folder Step 3 Install LAN Driver 1 Click on the Step 3 LAN folder and select the folder of LAN chip the system adopted 2 Select the OS folder your system is and double click on the exe file located in each OS folder Chapter 4 Driver Installation 4 3 Embedded Controller AEC 6877 3 Follow the instructions that the window shows 4 The system will help you install the driver automatically Step 4 Install Audio Driver 1 Click on the Step 4 Audio folder and select the OS folder your system is 2 Double click on the exe located in each OS folder 3 Follow the instructions that the window shows 4 The system will help you install the driver automatically Step 5 Install USB3 0 Driver 1 Click on the Step 5 USB3 0 folder and double click on the Setup exe file 2 Follow the instructions that the window shows 3 The system will help you install the driver automatically Step 6 Install RAID amp AHCI Driver Please refer to the Appendix C RAID amp AHCI Settings Step 7 Install ME Driver 1 Click on the Step 7 ME folder and select the OS folder your system is 2 Double click on the exe located in each OS folder 3 Follow the instructions that the window shows 4 The system will help you install the driver automatically Chapter 4 Driver Installation 4 4 Embedded Controller AEC 6877 Step 8 Serial Port Driver Optional 1 Click on the Step 8 Serial Port Driver Optional and
28. etup Utility Copyright C 2011 American Megatrends Inc Legacy USB Support Enabled Options Summary Legacy USB Support Enabled Default Disabled Auto Enable Legacy USB support AUTO option disables legacy support if no USB devices are connected DISABLE option will keep USB devices available only for EFI applications Mode Disabled Enabled Mode of operation of xHCI controller Chapter 3 AMI BIOS Setup 3 16 6877 Super IO Configuration Aptio Setup Utility Copyright C 2011 American Megatrends Inc gt Serial Port 0 Configuration Options Summary Serial Port 0 Set Parameters of Serial Port 3 COMA Configuration Serial Port 1 Set Parameters of Serial Port 4 COMB Configuration Chapter 3 AMI BIOS Setup 3 17 6877 Serial Port 0 Configuration Aptio Setup Utility Copyright C 2011 American Megatrends Inc Serial Port Enabled Options Summary Serial Port Disabled Enabled Default Enable or Disable Serial Port COM Change Settings Auto Default IO SF8h IRQ 3 4 IO 2F8h IRQ 3 4 IO 3E8h IRQ 3 4 IO 2E8h IRQ 3 4 Select an optimal setting for Super IO device Chapter 3 AMI BIOS Setup 3 18 Serial Port 1 Configuration Aptio Setup Utility Copyright C 2011 American Megatrends Inc Serial Port Options Summary Enabled AEC 6877
29. gnal Pin Signal 1 5V 2 GND 3 USBD 4 GND 5 USBD 6 USBD 7 GND 8 USBD 9 GND 10 45V Chapter 2 Hardware Installation 2 4 Embedded Controller AEC 6877 2 5 HDD Installation Step 1 Unfasten the four screws on the front and rear panels Step 2 Place the HDD to the HDD bracket and fasten to the bottom lid of AEC 6877 Chapter 2 Hardware Installation 2 5 Embedded Controller AEC 6877 Step 3 Fasten the screws on the front and rear panels and the brackets of AEC 6877 Chapter 2 Hardware Installation 2 6 Embedded Controller AEC 6877 2 6 CFast Card Installation Step 1 Unfasten the screws on the front and rear panels CFast Slot Chapter 2 Hardware Installation 2 7 Embedded Controller AEC 6877 2 7 PCI Express Card Installation Step 1 Unfasten the screws on the front and rear panels Step 2 Install a hold down bracket to fix the PCI or PCI Express Card and make sure the PCI or PCI Express Card installs properly Chapter 2 Hardware Installation 2 8 Embedded Controller AEC 6877 2 8 Wallmount Bracket Installation Fasten the brackets with the appropriate screws 57 lt A 2209
30. ly PCI Express Root Port 2 1E12 Intel R 7 Series C216 Chipset Family PCI Express Root Port 1 1E10 B 4 DMA Channel Assignments 4 A Direct memory access DMA 4 Direct memory access controller Appendix B I O Information B 7 Embedded Controller AEC 6877 Appendix RAID amp AHCI Settings Appendix C RAID amp AHCI Settings C 1 C 1 Setting RAID OS installation to setup RAID Mode Step 1 Copy the files below from Driver CD gt Step 6 RAID amp AHCI F6 Floppy x86 to Disk ia HCIC IA a KE E ca jaStorAC isStorAC x ZE Hi SERA A txtsetup cem OEM ga SI K Stork T Step 2 Connect the USB Floppy disk with RAID files to the board Appendix C RAID amp AHCI Settings C 2 AEC 6877 Step 3 The setting procedures In BIOS Setup Menu A Advanced gt SATA Configuration gt SATA Mode gt RAID Mode SATA Mode B Advanced Launch Storage OpROM gt Enabled Appendix C RAID amp AHCI Settings C 3 Embedded Controller AEC 6877 Step 5 The setting procedures In BIOS Setup Menu C Boot gt Boot Option 1 gt DVD ROM Type ICAC FD O UEFI FAT Boot DI 4 SATA FUJ Step 6 The setting procedures In BIOS Setup Menu D Save amp Exit gt Save Changes and Exit AZ uetam Appendix C RAID amp AHCI Settings C 4 Embedded Controller AEC 6877 Step 7 Press Ctrl I to enter MAIN MENU
31. nal Inc CompactFlash is a trademark of the Compact Flash Association e Intel Celeron and Core are trademarkes of Intel Corporation e Microsoft Windows is a registered trademark of Microsoft Corp e PC AT 5 2 and VGA are trademarks of International Business Machines Corporation All other product names or trademarks are properties of their respective owners Embedded Controller AEC 6877 Packing List Before you begin operating your PC please make sure that the following materials have been shipped 1 AEC 6877 Embedded Controller Phoenix Power Connector M3 x 4mm Screws 6 32 x 10mm Screws N Wallmount Brackets DVD ROM for manual in PDF format and Drivers If any of these items should be missing or damaged please contact your distributor or sales representative immediately iii Embedded Controller AEC 6877 Safety amp Warranty Read these safety instructions carefully Keep this user s manual for later reference Disconnect this equipment from any AC outlet before cleaning Do not use liquid or spray detergents for cleaning Use a damp cloth For pluggable equipment the power outlet must be installed near the equipment and must be easily accessible Keep this equipment away from humidity Put this equipment on a firm surface during installation Dropping it or letting it fall could cause damage The openings on the enclosure are for air convecti
32. on Protect the equipment from overheating DO NOT COVER THE OPENINGS Make sure the voltage of the power source is correct before connecting the equipment to the power outlet Position the power cord so that people cannot step on it Do not place anything over the power cord All cautions and warnings on the equipment should be noted If the equipment is not used for a long time disconnect it from the power source to avoid damage by transient over voltage Never pour any liquid into an opening This could cause fire or electrical shock Never open the equipment For safety reasons only qualified service personnel should open the equipment If any of the following situations arises get the equipment checked by service personnel a The power cord or plug is damaged b Liquid has penetrated into the equipment c The equipment has been exposed to moisture Embedded Controller AEC 6877 d The equipment does not work well or you cannot get it to work according to the user s manual e The equipment has been dropped and damaged f The equipment has obvious signs of breakage 15 DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW 20 C 4 F OR ABOVE 70 C 158 F IT MAY DAMAGE THE EQUIPMENT FCC This device complies with Part 15 Rules Waming Operation is subject to the following two conditions 1 this device may not cause harmful interference and
33. ootable Volunel RAIDO Stripe 128KB 149 1GB Yes Physical Disks Port Drive Model Serial 8 Size Type Status Vol ID 8 FUJITSU MH22080B K68F1972B HN 74 568 1 851912082305 SNJBSZAB 111 768 Appendix RAID amp AHCI Settings 7 Step 13 Choose Y Create RAID Volune Reset Disks to Non RAID Delete RAID Volune Recovery Volune Options Strip Size Status EXIT 51912882385 5NJ8SZRE 111 768 Appendix RAID amp AHCI Settings C 8 Embedded Controller AEC 6877 Step 15 Press F6 om Press F6 if you need to install a third party or RAID driver Step 16 Choose S Specify Additional Device ENTER Continue F3 Exit Appendix C RAID amp AHCI Settings C 9 Embedded Controller AEC 6877 Step 17 Choose Intel R Mobile Express Chipset SATA RAID Controller You have chosen to configure a SCSI Mr for use uith Hindous using a device sup is ded b 2 SATA RRID Cont EDD F3 Exit Step 18 It will show the model number you select and then press ENTER lindous Setup r special se for On a nass prage device S Specify Additional Devic ENTER Cont inue F3 Exit Appendix C RAID amp AHCI Settings C 10 AEC 6877 Step 19 Setup is starting Windows Setup is starting Hindous Appendix C RAID amp AHCI Settings C 11 C 2 Setting AHCI OS installation to setup AHCI Mode Step 1 Copy the files below from Driver CD
34. ppendix A Programming the Watchdog Timer A 8 Embedded Controller AEC 6877 MOV DX WORD PTR CS Cfg_Port 06h IN AL DX RET Read Configuration Data ENDP Write Configuration Data PROC NEAR MOV DX WORD PTR CS Cfg Port 04h OUT DX AL XCHG AL AH MOV DX WORD PTR CS Cfg Port 06h OUT DX AL RET Write Configuration Data ENDP Superio Set Reg proc near push ax MOV DX WORD PTR CS Cfg Port 04h mov al cl out dx al pop ax inc dx out dx al ret Superio Set Reg endp Set Logic Device proc near Set Logic Device proc near Appendix A Programming the Watchdog Timer A 9 Embedded Controller AEC 6877 push ax push cx xchg al cl mov cl 07h call Superio Set Reg pop cx pop ax ret Set Logic Device endp Select O2Eh gt Index Port 02Fh gt Data Port Cfg_Port DB 087h 001h 055h 055h DW 02Eh 02Fh END Main Note Interrupt level mapping OFh Dh not valid OCh IRQ12 03h IRQ3 02h not valid 01h IRQ1 00h no interrupt selected Appendix A Programming the Watchdog Timer A 10 Embedded Controller AEC 6877 Appendix I O Information Appendix B Information B 1 B 1 Address AEC 6877 Input output IO 00000000 0000001F Direct memory access controller 4 00000000 00000CF7 PCI bus 00000010 0000001F Motherboard resources 00000020 00000021 Programmable interrupt controller 00000022 0000003F Motherboard resources 098 00000024
35. r 1 General Information 1 3 Embedded Controller AEC 6877 1 2 Features e Fanless Design e Intel Core i7 3610QE i7 2710QE i5 2510E Celeron B810 Processor e Intel QM77 Chipset e Gigabit Ethernet RJ 45 x 2 e Three Independent Video Output for 2 DisplayPort VGA or DVI e USB3 0 x 4 e 4 Slot x 1 or PCI x 2 e COMx2 Chapter 1 General Information 1 4 Embedded Controller 1 3 Specifications AEC 6877 e CPU Intel Core i7 3610QE 2 3 GHz i7 2710QE 2 1 GHZ 15 2510E 2 5 GHz Celeron B810 1 6 GHz Processor with socket PGA988 Chipset Intel QM77 e System Memory 204 pin dual channel DDR3 SODIMM 1066 1333 1600 MHz x 2 up to 16 GB e Display VGA DB 15 x 1 Interface DVI DVI D x 1 support 1920 x 1080 60 Hz Others DisplayPort x 2 Storage SSD CFast slot Device HDD SATA 6 0Gb s x 2 support RAID 0 1 5 10 Network LAN Gigabit Ethernet RJ 45 x 2 Wireless Optional by Mini Card e Front Serial Port RS 232 x 1 Others Push Power button x 1 Standard Antenna Hole x 2 e Rearl O USB Host USB3 0 x 4 LAN RJ 45 x 2 Serial Port RS 232 422 485 x 1 Audio Mic in Line out Line out Chapter 1 General Information 1 5 Embedded Controller AEC 6877 KB MS PS 2 Keyboard x 1 Mouse x 1 Others Power input x 1 Expansion PCI E PCI E x4 x 1 AxM series or PCI x 2 Bx
36. r make changes to my computer 1 changes to Windows settings Net recommended Choose this only if you need to use programs that are not certified for Windows 7 because they do not support User Account Control Documents Pictures Music Games Computer Control Panel Devices and Printers Switch user Logoff Lock Help and Suppo Restart Sleep Hibernate Chapter 4 Driver Installation 4 6 AEC 6877 4 erm r 9 ee Organize v Open Print New folder Yc Favorites Date modified Type BE Desktop J Vista amd64 10 21 2011 8 28 AM File folder 1 Downloads Ji vista X86 10 21 2011 8 28 AM File folder Recent Places Ji win7 amd64 10 21 2011 8 28 AM File folder Ji win7 X86 10 21 2011 8 28 AM File folder Libraries J xp x86 10 21 2011 8 28 AM File folder Documents Epi 4 Windows Batch File Music Ev ro i Edit Print Pictures Videos Run as administrator Computer Troubleshoot compatibility amp Local Disk C Restore previous versions cx Local Disk D Sendto s New Voli New Volume E Ga C Network mud Create shortcut Delete Rename ated 10 21 2011 8 28 AM Windows Batch File Properties File Action esiz Computer Management Lo Driver Details System Tools Driver File Details gt Task Scheduler Communications Port COM4 3 Event Viewer gt 80 Shared Folders
37. r series AEC 6877 has been introduced by AAEON The AEC 6877 is a fanless industrial grade embedded controller with superior thermal solution inside which is designed for harsh environment use With newly Intel high performance 3 generation processor provides customers powerful computing technology and AEC 6877 adopts Intel QM77 power chipset support three independent displays which is convenient for customer in their applications Also with rich I O ports with VGA DVI Display port Ethernet RS 232 422 485 and USB 3 0 it helps you shorten product development time to fulfill extensive needs in various projects AEC 6877 is an ideal embedded platform for implementing custom applications for diversified applications Stable Design for Rugged Environment The AEC 6877 is designed for rugged environments due to the following reasons first it can withstand tough vibration testing up to 5g rms With the anti vibration hard drive device option the AEC 6877 can be used in high vibration environments In addition the AEC 6877 offers low power consumption system that while operating in ambient temperatures ranging from 0 to 55 C Chapter 1 General Information 1 2 Embedded Controller AEC 6877 The AEC 6877 is a standalone high performance controller designed for long life operation and with high reliability It can replace traditional methods and become the mainstream controller for the multimedia entertainment market Chapte
38. rosoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Microsoft ACPI Compliant System Appendix B I O Information B 6 AEC 6877 Embedded Controller 180 ISA 0x000000AB 171 ISA 0x000000AC 172 ISA 0x000000AD 173 gM ISA 0x000000AE 174 ISA 0x000000AF 175 gM ISA 000000080 176 1 ISA 000000081 177 15 0x00000082 178 ISA 0x000000B3 179 ISA 000000084 180 ISA 0x000000B5 181 ISA 0 00000086 182 ISA 0x00000087 183 ISA 0x000000B8 184 ISA 0x00000089 185 ISA 0x000000BA 186 ISA 0x000000BB 187 ISA 0x000000BC 188 ISA 0x000000BD 189 ISA 0x000000BE 190 PCI 0 00000008 11 0500000010 16 PCT 0x00000010 16 7 PCI 0x00000013 19 PCI 000000016 22 PCD0x0000
39. s Inc ACPI Sleep State S3 only Suspend to Options Summary ACPI Sleep State Suspend Disabled 1 CPU Stop Clock S3 Suspend to RAM Default Select the ACPI sleep state the system will enter when the SUSPEND button is pressed Chapter 3 AMI BIOS Setup 3 6 AEC 6877 Trusted Computing Aptio Setup Utility Copyright C 2011 American Megatrends Inc Security Device Support Disable Option Summary TPM SUPPORT Disable Default Enable Enables or Disables BIOS support for security device O S will not show Security Device TCG EFI protocol and INT1A interface will not be available Chapter 3 AMI BIOS Setup 3 7 6877 CPU Configuration Aptio Setup Utility Copyright C 2011 American Megatrends Inc Huper threading Enabled Options Summary Hyper threading Disabled Enabled Default Enabled for Windows XP and Linux OS optimized for Hyper Threading Technology and Disabled for other OS OS not optimized for Hyper Threading Technology When Disabled only one thread per enabled core is enabled Intel Disabled Default Virtualization Enabled Technology When enabled a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology Chapter 3 AMI BIOS Setup 3 8 AEC 6877 SATA Configuration IDE Aptio Setup Utility Copyright C 2011 American Megatrends
40. s that can help you to install the driver automatically Insert the driver DVD the driver DVD title will auto start and show the installation guide If not please follow the sequence below to install the drivers Follow the sequence below to install the drivers Step 1 Install Chipset Driver Step 2 Install VGA Driver Step 3 Install LAN Driver Step 4 Install Audio Driver Step 5 Install USB3 0 Driver Step 6 Install RAID amp AHCI Driver Step 7 Install ME Driver Step 8 Install Serial Port Driver Optional Please read instructions below for further detailed installations Chapter 4 Driver Installation 4 2 Embedded Controller AEC 6877 4 1 Installation Insert the AEC 6877 DVD ROM into the DVD ROM drive And install the drivers from Step 1 to Step 8 in order Step 1 Install Chipset Driver 1 Click on the Step 1 Chipset folder and double click on the infinst autol 9 3 0 1026 exe file 2 Follow the instructions that the window shows 3 The system will help you install the driver automatically Step 2 Install VGA Driver 1 Click on the Step 2 VGA folder and select the OS folder your system is 2 Double click on the Setup exe file located in each OS folder 3 Follow the instructions that the window shows 4 The system will help you install the driver automatically Note If the OS is Windows XP you have to install the driver of dotNet Framework first Simply click on dotnetfx35 exe locat
41. tel R Active Management Technology SOL COM3 0980 F7D3C000 F7D3COOF Intel R Management Engine Interface 288 F8000000 FBFFFFFF Motherboard resources 088 FEDOOOOO FEDOO3FF High precision event timer FED10000 FEDI7FFF Motherboard resources 288 FED18000 FEDIBFFF Motherboard resources 088 FED19000 FED19FFF Motherboard resources ji FED1C000 FEDIFFFF Motherboard resources 088 FED20000 FED3FFFF Motherboard resources 088 FED40000 FED44FFF System board 88 FED45000 FED8FFFF Motherboard resources FED90000 FED93FFF Motherboard resources 088 FEEOOOOO FEEFFFFF Motherboard resources yi FF000000 FFFFFFFF Intel R 82802 Firmware Hub Device 88 FF000000 FFFFFFFF Motherboard resources Appendix B I O Information B 4 Embedded Controller B 3 IRQ Mapping Chart AEC 6877 4 Interrupt request RQ SA 0x00000000 00 ISA 000000001 01 7 ISA 000000003 03 7 ISA 0x00000004 04 JE ISA 000000008 08 F4 SA 0x0000000C 12 ISA 0x0000000D 13 ISA 0x00000051 81 gM ISA 000000052 82 ISA 000000053 83 ISA 000000054 84 1 ISA 000000055 85 ISA 0x00000056 86 ISA 0x00000057 87 ISA 000000058 88 1 ISA 000000059 89 1M ISA 0 0000005 90 q 15 0x0000005B 91 ISA 0x0000005C 92 ji ISA 0x0000005D 93 ISA 0x0000005E 94 ISA 0x0000005F 95 ISA 000000060 96
42. tel TXT LT Configuration Aptio Setup Utility Copyright C 2011 American Megatrends Inc Chapter 3 AMI BIOS Setup 3 12 AEC 6877 PCH FW Configuration Aptio Setup Utility Copyright C 2011 American Megatrends Inc MDES BIOS Status Code Disabled Options Summary MDES BIOS Status Disabled Default Code Enabled Enable Disable MDES BIOS Status Code Firmware Update Configure Management Engine Technology Configuration Parameters Chapter 3 AMI BIOS Setup 3 13 AEC 6877 Firmware Update Configuration Aptio Setup Utility Copyright C 2011 American Megatrends Inc Me FH Image Re Flash Disabled Options Summary Me FW Image Disabled Default Re Flash Enabled Enable Disable Me FW Image Re Flash function Chapter 3 AMI BIOS Setup 3 14 6877 AMT Configuration Aptio Setup Utility Copyright C 2011 American Megatrends Inc Intel AMT Enabled Options Summary Intel AMT Disabled Enabled Default Enable Disable Intel amp Active Management Technology BIOS Extension Note iAMT H W is always enabled This option just controls the BIOS extension execution If enabled this requires additional firmware in the SPI device Un Configure ME Disabled Default Enabled OEMFlag Bit 15 Un Configure ME without password Chapter 3 AMI BIOS Setup 3 15 AEC 6877 USB Configuration Aptio S
43. y has lost power and the configuration information has been erased The AEC 6877 CMOS memory has an integral lithium battery backup for data retention However you will need to replace the complete unit when it finally runs down Chapter 3 AMI BIOS Setup 3 2 Embedded Controller AEC 6877 3 2 AMI BIOS Setup AMI BIOS ROM has a built in Setup program that allows users to modify the basic system configuration This type of information is stored in battery backed CMOS RAM and BIOS NVRAM so that it retains the Setup information when the power is turned off Entering Setup Power on the computer and press lt Del gt or F2 immediately This will allow you to enter Setup Main Set the date use tab to switch between date elements Advanced Advanced BIOS Features Setup including TPM ACPI etc Chipset Host bridge parameters Boot Enables disable quiet boot option Security Set setup administrator password Save amp Exit Exit system setup after saving the changes Chapter 3 AMI BIOS Setup 3 3 AEC 6877 Setup Menu Setup submenu Main up Utilitu Copuright C 2011 merican Megatrends Inc Sustem Date Chapter 3 AMI BIOS Setup 3 4 AEC 6877 Setup submenu Advanced Aptio Setup Utility Copyright C 2011 American Megatrends Inc oot i a 4 LI gt ACPI Settings Chapter 3 AMI BIOS Setup 3 5 AEC 6877 ACPI Settings Aptio Setup Utility Copyright C 2011 American Megatrend
Download Pdf Manuals
Related Search