PAN06-1/-2/-3 In Wall Dual relay(1 way) switch module P - O Z-wave
Contents
1. lt J LED Indication To distinguish what mode the switch is in view from the LED for identification State Type LED Indication 1 Put the in wall switch into a wall box and connect the AC power wire L N to Whenever we switch On and off of the PANO6 by S1 S2 or On Off PANO6 connector L N 2 Connect the wall switch to the PANO6 as Fig1 3 There are 3 mode PANO6 can be configured to match different kind of wall switch please refer to 3 2 Edge Pulse Edge Toggle mode which described in next section of this user manual If Edge Toggle mode has been set and the S1 S2 is connect to normal bi stable switch every time when change the state of the wall switch will also swap the state of Relay1 or Relay2 Programming 1 Basic Command Class Binary Switch Command Class The Switch will respond to BASIC and BINARY commands that are part of the Z Wave system 1 1 BASIC_GET BINARY_SWITCH_GET Since the switch have two relay the Switch will report its On Off state to the node of Group by setting Configuration parameter 1 Configuration parameter 1 1 default Report ON either relay 1 ON or relay 2 ON Report OFF when both relay 1 and relay 2 OFF Since the switch have two relay the load attached to the Switch will turn on or off upon receipt of the following commands from a Z Wave Controller by setting Configuration parameter 1 Configuration parameter 1 1 default switch ON and OFF both relay 1 and relay 2 Configuration param2. HANNEL MULTI CHANNEL_CMD_ENCAP 3 1 Selected Endpoint Source End Point 0x01 this is the endpoint of command owner If Controller not using Multi_Channel command class to access the endpoint of here we assume endpoint is 1 gt if the PANO6 you may configure the endpoint value to react the Basic Command Class or Binary Switch Command Class Edge Toggle mode owner doesn t support multi Channel this value will be 0 3 1 1 Selected Endpoint 1 Default Selected Endpoint is 1 Basic Set or Binary_ Switch _Set ON Relay1 ON amp Relay2 ON Basic Set or Binary Switch Set OFF Relay OFF 7 4 Relay2 OFF Bit Address Destination End Point 0x02 Bit Address 0 Destination End Point range 3 Command Class 0x25 Command_Class_ Switch Binary 0x25 Command 0x01 Switch_Binary_Set 0x01 Parameter 1 0x00 ON 0xFF gt OFF 0x00 Basic_Get or Binary_Switch_Get Relayi ON _ or ON Relay2 ON Basic_Get or Binary_Switch_Get Relay1 OFF amp OFF Relay2 OFF 3 1 2 Selected Endpoint 2 Similar like Selected Endpoint 1 but only relate to Relay1 and ignore Relay2 3 1 3 Selected Endpoint 3 Similar like Selected Endpoint 1 but only relate to Relay2 and ignore Relay1 3 2 Edge Pulse Edge Toggle mode Manual switch S1 and S2 can set to Edge mode or Pulse mode or Edge Toggle mode default value is Edge mode Edge mode this mode is suitable for the bi stable wall switch that has indicator point on the switch and t
3. PANO6 1 2 3 a es Sey SS senate PANOGAI In Wall Switch 2 Relay 1A TYPE BOSODHDOSS s2 s S L xw Fig 1 Assembling This in wall switch module is a transceiver which is a Z WaveTM enabled device and is fully compatible with any Z WaveTM enabled network Mini size design let the module can easily hide itself into the wall box and that will be good for the house decoration There are many kind of application by using the module to switch Load On and Off one main application is the light control If connect the com port directly to AC Line terminal the new smart relay calibration technology can reduce the inrush current caused by the load and let the module work perfectly with many kind of light like incandescent fluorescent and LED light This module can also connect to alternative power supply like DC 12V to switch on off 12V MR 16 light as follow picture Adding to Z Wave Network In the front casing there is an on off button with LED indicator below which is used to toggle switch on and off or carries out inclusion exclusion reset or association When first power is applied its LED flashes on and off alternately and repeatedly at 2 second intervals It implies that it has not been assigned a node ID and cannot work with Z Wave enabled devices Auto Inclusion The function of auto inclusion will be executed as long as the in wall switch does not have Node ID and just connect the switch to main p
4. e load attached or check continuously but cannot max load cannot exceed control 1500W 1650W Specification 100 240VAC 24 60V DC 10 Operating Voltage 1500W X2 220V 800W X 2 120V Range Minimum 30 m in door 100m outdoor _ line of sight Operating Temperature 0 40 Frequency Range PANO6 1 868 42 EU PANO6 2 908 42 USA Canada PAN06 3 922 5 923 9 926 3MHz Taiwan JP MHz Specifications are subject to change and improvement without notice mmm ce X FCC ID RHHPANO6 Warning 1 Plug out to disconnect from power supply Do not plug in line 2 Do not exceed the max rating Disposal x ae This marking indicates that this product should not be disposed with other household wastes throughout the EU To prevent possible harm to the environment or human health from uncontrolled waste disposal recycle it responsibly to promote the sustainable reuse of material resources To return your used device please use the return and collection systems or contact the retailer where the product was purchased They can take this product for environmental safe recycling Company of License Holder Philio Technology Corporation Address of License Holder 8F No 653 2 Zhongzheng Rd Xinzhuang Dist New Taipei City 24257 Taiwan R O C FCC Interference Statement This equipment has been tested and found to comply with the limits for a Cla
5. eter 1 2 switch ON and OFF of relay 1 Configuration parameter 1 3 switch ON and OFF of relay 2 Command Class Basic Basic Set Value 255 0xFF the load attached to the Switch turns on Command Class Basic Basic Set Value 0 0x00 the load attached to the Switch turns off Command Class Switch Binary Switch Binary Set Value 255 0xFF the load attached to the Switch turns on Command Class Switch Binary Switch Binary Set Value 0 0x00 the load attached to the Switch turns off Configuration parameter 1 2 Report ON when relay 1 ON Report OFF when relay 1 OFF 2 Z Wave s Groups Association Command Class Version 1 Configuration parameter 1 3 Report ON when relay 2 ON Report OFF when relay 2 OFF The Switch can be set to send reports to control associated Z Wave devices It supports 3 association groups which every group has one node support Group1 Group3 support SWITCH_BINARY_REPORT Basic Report Command For group 1 the Switch will report ON OFF status of Relay1 and Relay2 Report OFF Command Class Basic Basic Report Value 0 0x00 For group 2 the Switch will report ON OFF status of Relay1 Report ON Command Class Basic Basic Report Value 255 0xFF For group 3 the Switch will report ON OFF status of Relay2 2 1 Auto report to Grouping 1 3 Maximum Node 1 Binary Switch Get Command Command Class Switch Binary Switch Binary Get 2 1 1 On Off Event Report Binary Switch Report Command When on
6. he same position correspond to same state of relay1 and relay2 if the PANO6 relay change the state because of receiving Z Wave RF command it may need two times of change switch on to off or switch off to on to let relay back to the correspond state Pulse mode this mode is suitable for the toggle type wall switch to swap the state of Relay1 or Relay2 Edge Toggle mode this mode is suitable for the normal bi stable switch every time when change the state of the wall switch will also swap the state of Relay1 or Relay2 4 Command Classes The Switch supports Command Classes including COMMAND_CLASS_SWITCH_BINARY COMMAND_CLASS BASIC COMMAND_CLASS MANUFACTURER_SPECIFIC_V2 COMMAND_CLASS_VERSION COMMAND_CLASS_SWITCH_ALL COMMAND_CLASS_ASSOCIATION_V1 COMMAND_CLASS_ CONFIGURATION COMMAND CLASS MULTI CHANNEL V3 COMMAND CLASS ALARM Troubleshooting i i itch i 1 Check power connections connect to the Main 2 Don t open up the Switch and send power it for repair 2 The Switch break down Check if the load connect Set the ON OFF switch of the load into the Switch has its attached to ON own ON OFF switch illuminating but cannot control the ON OFF Switch of the load attached 1 Not carry out association 1 Carry out association illuminating but the 2 Wait for a while to re try Detector cannot control 2 Same frequency the Switch interference LED keep flashing Overload occurs Remove th
7. humid or dusty place enter inclusion mode i 2 The suitable ambient temperature for the Switch is 00 40 2 Within 1 second press Include i 3 Do not locate the Switch where exists combustible substances or any source of button of PANO6 again for 5 intervals By pressing S1 S2 or On Off button it will stop flashing temporarily However after disconnect and reconnect the Switch the LED will flash on and off alternately at 2 second intervals seconds until LED is off heat e g fires radiators boiler etc pe are a E AEN 4 After putting it into use the body of Switch will become a little bit hot of which phenomenon is normal Association 1 Have Z Wave Controller entered One press one flash Installation association mode Or Pressing Include button of PANO6 three times within 1 5 seconds will enter association mode 2 There are 3 groups for the switch X Including a node ID allocated by Z Wave Controller means inclusion Excluding a node ID allocated by Z Wave Controller means exclusion X Failed or success in including excluding the node ID can be viewed from the Z Wave Controller Sometimes people are not easy to execute exclusion or inclusion especially when s P PANO6 already installed in a wall box To solve this issue PANO6 support a special feature that can use S1 or S2 to execute exclusion inclusion Reset or Association y at the first 3 minutes when first time connect to main power
8. oint 0x05 this is the endpoint of command owner here we assume endpoint is 5 gt if the owner doesn t support multi Channel this value will be 0 Bit Address Destination End Point 0x01 Bit Address 0 Destination End Point range from 1 3 Command Class 0x25 Command_Class_Switch_Binary 0x25 Command 0x02 Switch_Binary_Get 0x02 Below is the example show PANO6 report to last command COMMAND CLASS MULTICHANNEL MULTI CHANNEL CMD _ENCAP Source End Point 0x01 Since the endpoint is 1 so PANO6 will reply ON OxFF either Relay 1 or Relay2 is ON report OFF 0x00 when both Relay 1 and Relay2 OFF Bit Address Destination End Point 0x05 Bit Address 0 Destination End Point Command Class 0x25 Command 0x03 Command_Class_Switch_Binary 0x25 Switch_Binary_Report 0x03 p 1 OxFF ON 0xFF gt OFF 0x00 arameter 1 0x 3 Z Wave s Configuration 2 2 2 BINARY SWITCH SET By using BINARY_SWITCH_SET Command of Multi Channel Command Class rarometer Byte Slected 1 1 3 1 1 Relay1 amp Encapsulation Command you can switch both Relay1 and Relay2 ON OFF by End Point Relay2 setting endpoint to 1 or switch Relay1 ON OFF by setting endpoint to 2 or switch l snd Relay2 ON OFF by setting endpoint to 3 Edge or Edge mode Pulse mode or Pulse mode The example of the command show that switch off relay1 of PANO6 Edge Tog gle mode COMMAND CLASS _ MULTIC
9. or off state has been changed ex Press S1 S2 or include on off Report OFF Command Class Switch Binary Switch Binary Report Value button it will send Binary Switch Report to the nodes of Group1 3 0 0x00 Report ON Command Class Switch Binary Switch Binary Report Value 255 0xFF Binary Switch Report 1 2 BASIC_SET SWITCH_BINARY_SET ON Command Class Switch Binary Switch Binary Report Value 255 0xFF OFF Command Class Switch Binary Switch Binary Report Value 0 0x00 2 1 2 Overload alarm report command When PANO6 detect the overload it will send Alarm Report to the correspond Group The content of Alarm Report Alarm report command Command Class Alarm Alarm Report Alarm Type 0x08 Alarm Level OxFF 2 2 Multi Channel Command Class Version 3 PANO6 also support muti channel command class version 3 which include BINARY _SWITCH_GET BINARY_SWITCH_SET You may control or get report from 3 endpoint of PANO6 2 2 1 BINARY_SWITCH_GET You may get the ON OFF state from every endpoint when endpoint set to 1 PANO6 will reply ON OxFF either Relay 1 or Relay2 is ON report OFF 0x00 when both Relay 1 and Relay2 OFF state of Relay1 If endpoint set to 3 and PANO6 will reply state of Relay2 If endpoint set to 2 PANO6 will reply Below is an example show a source endpoint 5 send a Get command to PANO6 endpoint 1 COMMAND_CLASS_MULTI_CHANNEL MULTI CHANNEL CMD _ENCAP Source End P
10. ower Note Auto inclusion timeout is 4 minute during which the node information of explorer frame will be emitted once every 5 seconds Unlike inclusion function as shown in the table below the execution of auto inclusion is free from pressing the On Off button on the Switch The table below lists an operation summary of basic Z Wave functions Please refer to the instructions for your Z WaveTM Certificated Primary Controller to access the Setup function and to include exclude associate devices Function Description LED Indication No node ID The Z Wave Controller does not allocate 2 second on 2 second off a node ID to the Switch Inclusion 1 Have Z Wave Controller entered One press one flash inclusion mode a button or RF command the LED will lights up 1 second and then off No node ID Under normal operation when the Switch has not been allocated a node ID the LED flashes on and off alternately at 2 second 2 Pressing Include button of PANO6 three times within 1 5 seconds will enter inclusion mode Exclusion 1 Have Z Wave Controller entered One press one flash exclusion mode 2 Pressing Include button of PANO6 three times within 1 5 seconds will enter exclusion mode Node ID has been excluded 2 second on 2 second off Reset 1 Pressing Include button of PANO6 One press one flash Choosing a Suitable Location three times within 1 5 seconds will l l 1 Do not locate the Switch facing direct sunlight
11. ss B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment This transmitter mus
12. t not be co located or operating in conjunction with any other antenna or transmitter
Download Pdf Manuals
Related Search