Technical information press here
Contents
1. ffect controls the volume of the signal to be sent to the effect unit 42 Channel 3 Input sensitivity selector of the pre amplifier mic for low line for higher input level 43 Channel 3 Treble equalizer control Channel 3 Bass equalizer control 45 Channel 3 Effect controls the volume of the signal to be sent to the effect unit Channel 3 Volume control with coupled trim gain control SAGA Semi automatic gain adjust a7 Channel 2 Volume control with coupled trim gain control SAGA Semi automatic gain adjust Channel 5 volume control Master volume control Channel 4 volume control 1 Program selector 1 for integrated effect device type 0200 Program selector 2 for integrated effect device option 3 Filter equalizer switch to cut mid low frequency at 350 Hz Channel 1 balanced 3 pole input socket for 6 3mm jack plug s Channel 2 balanced 3 pole input socket for 6 3mm jack plug volume control with coupled trim gain CONE CAS PO 2223 DOODGA mid level seaaaa ODOORN 36 35 21 20 19 18 17 46 05 09 43 Input sensitivity selector of the 6 Channel 3 balanced 3 pole input socket for 6 3mm jack plug 7 Channel 4 balanced 3 pole input socket for 6 3mm cD 34 QOQOOOOO jack plug Channel 5 balanced 3 pole input socket for 6 3mm jack plug Mix output of the levels adjusted by the effect controls mix from the outp2. for your ease the hearing volume with in order to observe the sound quality of the output Turn slowly the control ch level clockwise and increase the volume as long as the signal is clean and undistorted but not over the discontinued mark at the end of the scale When you begin to perceive any distortion turn back the control until the distortion disappears Test the result then also with a signal that could be typically the loudest possible to be expected and repeat the procedure if necessary 3 2 Check now maximum volume performance by turning the control to the discontinued mark at the end of the scale If the level is not enough use one of the channels 1 2 or 3 for this signal put the appropriate sensitivity selector to position mic and repeat the procedure 3 1 if necessary 3 3 If desired adjust the equalizer controls of the appropriate channel at your convenience Particularly when setting one or various equalizer controls to considerable high amplification gain it may become necessary to reduce or to readjust the appropriate ch level corresponding to the procedure 3 1 A M P D 66111 Saarbruecken Germany Tel 49 681 9686881 Fax 49 681 62495 www cromacord com RCPMXVP200 E003 20030403 All rights reserved PAGE 3 6 PDF wurde mit pdfFactory Prufversion erstellt www context gmbh de USER MANUAL XQ2714corc PODIUM MXV P200 OPERATION INSTRUCTIONS page 2 4 Connecting an external effect device Connect the soc
3. 0 KHz Effect send post volume control Channel 3 line mic same as Channel 2 Channel 4 line 3 dB bis 7 dB 2x 60 KQ unbalanced balanced when using 3 pole plug Channel 5 line same as Channel 4 OUTPUTS Master prefader 16 dB at 10KQ or 4 dB at 600Q unbalanced short circuit proof Master postfader same as master prefader Option master outputs can be internally bridged to configure one balanced output Master effect same as master prefader SIGNAL PROCESSING for internal power amplification Filter switch 6 dB cut at 350 Hz Signalcontroller fully automatic dynamic compressor limiter and signal enhancer with dynamic frequency response matching and complex selective regulation of up to 30 dB for best psychoacoustic results of acoustic music instruments and microphones Power amplification 60 90 120 Watt RMS 8Q RMS 4Q with extension speaker cabinet min 8Q connected music power protection circuits against switching on noise over heat and short circuit Speakers 2 way system with 8 low mid speaker and dyn high frequency driver horn 98 dB 1W 1m frequency range 55 20000 Hz Power supply 230V 50 60 Hz 125 VA mains fuse 1A slow blow can be internally changed to 115V 50 60Hz 125VA 1 6A slow blow Cabinet 16mm high density particle board spatter finish RAL 4004 dark purple ruby protective front of perforated sheet metal 1 5mm prepared to mount optional std flange for speaker stand on up to 3 sides 2
4. USER MANUAL 474 core PODIUM MXV P200 SAFE OPERATION AND GENERAL RECOMMENDATIONS Keep away from water and humidity weather electrical P discharge and strong sun or heat radiation exceed 35 C Do not operate immediately after changing the ambient temperature Particularly when moving from cold to hot and humid environment the metal parts and electronic For adequate cooling the ambient temperature should not x components can be affected by condensed water Wait for about 15 min until the PODIUM MXV P will be adapted to the ambient temperature 3 A Make sure to connect the PODIUM MXV P to the appropriate supply voltage and quality mains supply Use the cable that is supplied with the PODIUM MXV P the connection must be 3 pole grounded If you are uncertain about it grounding should be checked by an expert To avoid risk of injury i e tripping over cables or damaging cables and the device the connected lines should be placed very careful 2h a S lt N Do not operate the PODIUM MXV P and the connected devices near the strong electromagnetic fields and or high voltage equip ment like emitting antennas i e for instance mobile telephone large transformers motors and generators neon lights Do not expose yourself to excessive hearing of volume or high sound pressure levels Be aware of the possible consequences for your hearing Try allways when possible to place the PODIUM MXV P eff
5. axis and to add optional protecting hard cover for trans portation Dimensions 396mm x 290mm x 265mm Weight 11kg A M P D 66111 Saarbruecken Germany Tel 49 681 9686881 Fax 49 681 62495 www cromacord com RCPMXVP200 E005 20030403 All rights reserved PAGE 5 6 PDF wurde mit pdfFactory Prufversion erstellt www context gmbh de USER MANUAL ARIA coc PODIUM MXV P200 DIGITAL MULTIEFFECT EQUIPMENT type 0200 The built in effect device is wired internally to the output s pin dry coming from channels 1 to 3 that are individually adjustable by their appropriate ards a and as Referring to the programm chart below the desired effect mode can be selected by using the 16 step rotary encoder 1 The output of the effect device is internally wired to pin mix of the socket and at the same time connected also through the switched socket to it s appropriate pin hot The intensity of the effect signal returned through channel 5 can be adjusted and mixed to the master signal with the appropriate control 18 Delay 1 125 ms slapback delay for vocals and guitars 2 Room 3 Warm room for guitars and rhythm instruments 3 Room 2 Ambience for acoustic mixes and synth souns 4 Plate 3 Short vintage plate reverb for snares and guitars 5 Chorus Crorsiorgutarsan pinos 6 Plae 1 Ciassio plate reverb for lead vocals and instrumens 8 Piae 2 Sizzling bright plate reverb for vocals and rums 9 Flange Flangerforjetwash eff
6. ective to improve the listening volume for the audience while reducing the sound pressure level in the near field to the level that is necessary Normally the PODIUM MXV P should be placed at the same height as the ears of the audience For servicing or repair refer to an authorized expert avoid unauthorized alteration do not try to open or disassemble any screw or connection P lt For damages that are caused by unauthorized alteration or misuse we refuse any responsibility fa R zZ m lt z X P D 66111 Saarbruecken ame Tel 49 681 9686881 Fax 49 681 62495 www cromacord com MX VP200 E001 20030403 All rights reserved PAGE 1 6 PDF wurde mit pdfFactory Prufversion erstellt www context gmbh de USER MANUAL 4 14 lt core PODIUM MXV P200 OPERATING ELEMENTS AND FEATURES Channel 1 control SAGA Semi automatic gain adjust 2 Channel 1 Effect controls the volume of the signal to be sent to the effect unit GB Channel 1 Bass equalizer control 4 Channel 1 frequency control of the semiparametric mid frequency equalizer 5 Channel 1 control mid equalizer volume 6 Channel 1 Treble equalizer control Q Channel 1 preamplifier mic for low level Channel 2 Bass equalizer control 9 Channel 2 Treble equalizer control Channel 2 Input sensitivity selector of the pre amplifier mic for low line for higher input level line for higher input 1 Channel 2
7. ects SSCS 10 Rotary Speaker Rotary speaker emulation for organs and guias Hant Bright hall reverb for drums guitars and vocas 12 Chorus Roomt Chorus with reverb for guitars synths and pianos 13 Delay 2 190ms delay for percussive arpeggios SSCS a bypass No effect output signal s a identical digital copy 5 Hall 2 Warm hall for acoustic guitars pianos and vocals 16 Chorus oom 2 Auto wah guitar effect reverb for lead instruments Connecting additional effect devices and combined applications A The output cable of an external effect device is connected to the input The socket s integrated switch automatically disconnects the internal routing of channel 5 to the internal effect device Channel 5 is now receiving only the output signal of the external device The output eff send has to be connected to the input of the external device by using a 3 pole plug Connected with pin dry the external device receives a signal without effect Connected with pin mix the external device receives the output signal of the internal device B Pin mix of the socket is connected to pin hot of the socket The internal effect device can be used as stated before At the same time the input of an external device can be connected as mode A it s appropriate output can be returned and individually adjusted through any channel or by various channels C The various combinations proposed before at A and B can be selected and c
8. ket eff send 29 to the input of the effect device as well as it s output to the input ch 5 ret 28 Adjust at your convenience with eff send 2 11 and 15 the relative intensity of the effect for each individual channel First of all set the appropriate eff send control of the instrument that can be expected to require the highest intensity close to maximum adjust at your convenience the total mix of the required intensity with the control ch5 ret 48 Then adjust the required effect intensity of the other channels with their appropriate eff send controls 5 Using the preamp outputs The 3 pole master out socket is delivering 2 independant unbalanced preamplifier outputs that can be used at the same time with a cable lt 3 pole jack to 2xmono Jjack gt Particularly for avoiding hum generated by ground loops the connection to other amplifiers and devices that are grounded through a 3 pole mains connection multiple grounded should be splitted by using a DI BOX or a suited audio transformer 5 1 The signal of the pin pre does never depend on master vol 9 it works as if master vol would be set at maximum The users hearing volume towards the built in amplifier can be adjusted independently at any moment with the control 49 This is particularly suitable e g when connecting to a P A sound reinforcement system while using the amplifier as active monitor or when connecting to a recording device while keeping the rec
9. ontrolled externally using a suitable connection device e g a foot switch Technical data ADC DAC 24 bit 44 1 KHz 64x oversampling frequency range 20 20000 Hz Noise 105 dB THD N 95 dB Input max 10dB 2KQ Output 20dB 10KQ A M P D 66111 Saarbruecken Germany Tel 49 681 9686881 Fax 49 681 62495 www cromacord com RCPMXVP200 E006 20030403 All rights reserved PAGE 6 6 PDF wurde mit pdfFactory Prufversion erstellt www context gmbh de
10. ording level constant 5 2 The signal of the pin post is always depending proportionally on the control master vol 9 This is particularly suitable when connecting other amplifiers that will be controlled together as slaves 6 Connecting extension cabinet Make sure that the impedance is minimum 8 Ohm and that the technical condition of the speaker system i e risk of wrong impedance due to failure of a tweeter and it s cables and connectors i e risk of short circuit due to damaged components is perfect Plug the speaker cable min 2x0 75mm diameter with 2 pole jack into the socket 61 Do not use microphone or instrument cables A M P D 66111 Saarbruecken Germany Tel 49 681 9686881 Fax 49 681 62495 www cromacord com RCPMXVP200 E004 20030403 All rights reserved PAGE 4 6 PDF wurde mit pdfFactory Prufversion erstellt www context gmbh de USER MANUAL 2714 corc PODIUM MXV P200 TECHNICAL DATA INPUTS Channel 1 line mic 20dB to 6dB 50dB to 20dB 2x 160KQ unbalanced balanced when using 3 pole plug Bass equalizer 13 dB at 100 Hz Mid intensity 15 dB 13 dB at 1 6KHz frequency control at middle position Mid frequency 375 Hz to 5 5 KHz Treble equalizer 12 dB 15 dB at 10 KHz Effect send post volume control Channel 2 line mic 20dB to 6dB 50dB to 20dB 2x 80KQ unbalanced balanced when using 3 pole plug Bass equalizer 13 dB at 100 Hz Treble equalizer 12 dB 15 dB at 1
11. roove 1 3 Sensitivity selectors 7 10 42 in position line 1 4 Filter switch 3 in position off Now you can switch on the mains power supply 2 Input connection Depending on the instrument or signal source and the required features there are different possibilities of using up to 5 instruments at the same time Plug in the cable to the appropriate input connector 2 1 channel 4 7 or channel 5 8 suited for sources and instruments with high output level if there is no need to use an internal equalizer and also no need for adding an internal effect to be mixed down for instance instruments with preamplifier and or equalizer like keyboard CD player etc 2 2 channel 2 5 or channel 3 for sources and instruments that can not be amplified as stated before 2 1 2 3 Channel 1 for sources and instruments when a semi parametric mid equalization is required 2 4 Channel 1 2 or 3 suited for microphones with low output level with possibility to make balanced connection with adapter cable 3 pole jack to XLR female 3 Adjusting the signal The individual volume of each channel is to be adjusted with the controls ch level a7 the required volume of the total mix of the individual channels is to be adjusted with master vol 19 3 1 Start adjusting the choosen channel and turn clockwise the appropriate control ch level as well as the control master vol 449 until the signal can be heard Try to adjust or limit
12. ut of the integrated effect device option dry without effect or from the input of effect device 2 preamplifier master outputs before filter equalizer switch and the signal controller limiter post after master volume control pre before master volume control Output for extension loudspeaker min 8 Ohm Mains fuse holder 250V 5x20mm 1 A slow blow con tains 1 spare fuse for replacing Mains inlet connector EN60 320 1 for cold condition lighting mains power switch not in use reserved for optional upgrading not in use reserved for optional upgrading blind plate 1 reserved for optional accessory module blind plate 2 reserved vid supr blind plate 3 reserved vid supr chS ret ch ch3 che cha I Cecccce A M P D 66111 Saarbruecken Germany Tel 49 681 9686881 Fax 49 681 62495 www cromacord com RCPMXVP200 E002 20030403 All rights reserved PDF wurde mit pdfFactory Prufversion erstellt PAGE 2 6 www context qmbh de USER MANUAL X27 core PODIUM MXV P200 OPERATION INSTRUCTIONS page 1 1 Start position before switching on In order to avoid unpredictable operation conditions as idle noise feedback distortion etc the PODIUM MXV P should be set to start DO before switchin on 1 1 master vol 19 ch level 16 a7 20 eff send 2 aa and 45 set to zero level left terminal 1 2 Equalizer controls 3 5 8 9 43 4 in position center g
Download Pdf Manuals
Related Search