Printer Friendly Hillcrest X Series Owners Manual
Contents
1. 4 Plug the charger into a standard 110 120 volt household outlet 5 When the battery is fully charged both the red light and the green light will glow brightly 6 Once your battery is fully charged leave the charger plugged in and the battery connected when not in use This will maintain your battery in good condition especially during periods of non use KL UI g lt L O 0 gt KL E lt D Keep Your Battery Connected to the ReadyPro Charger at ALL TIMES Always recharge your battery immediately after each use Never wait a day before recharging If the battery is left discharged for long periods of time it will deteriorate faster shortening the life of your new battery Never use the battery to play more than 18 holes of golf on a single charge Doing so will lessen the life of your battery An unused TG 31 battery will lose its charge in about 1 month 30 days If it remains discharged it can be permanently damaged To maintain your battery s life it must remain connected to the charger while not in use Failure to do so will void the warranty About the ReadyPro Electronic Battery Charger The ReadyPro charger is designed to charge 12 volt deep cycle gel filled batteries such as your special Hillcrest X Gel battery It is also designed to remain connected to your battery indefinitely when you are not playing to maintain the battery in good condition while stored for long periods of time The standby charging m2. Command indicator light flashes normally My Remote Guidance System does not function All connections are made properly but the Confirm Command indicator does not flash Intermittent and erratic operation My X Series shuts off loss of steering directional control or will not restart My Remote Guidance stops unexpectedly and will not restart right away ET e 1 Circuit board needs to be reset 2 Water or debris could be inside connection plugs 9 volt battery connector inside the Remote Transmitter may be loose Outside interference Grass or debris in the male plugs and female connectors 1 Turn the Function Switch OFF wait 5 seconds 2 Clean and dry all male plugs and female connectors Using pliers carefully tighten Remote Transmitter battery metal connection snap then reconnect the battery By FCC regulation Remote Guidance System must accept all outside interference See label on the Remote Receiver Clean and dry all male plugs and female connectors Seet pronto ges Diminished operating range Weak 9 volt battery in the Replace the 9 volt battery It is particularly when turning left or right Remote Transmitter recommended that you replace the 9 volt battery every three months Remote Transmitter battery has an Remote Transmitter keypad or circuit Return to Kangaroo for repair unexpectedly short life span board needs replacing Erratic Remote Guidance operation
3. most golfers will be making many directional adjustment signal transmissions However if you do not press any button on the Remote Transmitter for 30 seconds your X series will stop This is a safety feature not a defect If your X Series stops just press the GO button and the X Series will start again Remote Transmitter The Remote Transmitter is supplied with a fresh standard Alkaline 9 volt battery The battery compartment is located on the bottom rear of the transmitter The cover slides off for easy battery replacement Under normal use the 9 volt battery should last 3 months Replace the Remote Transmitter battery at least every three months Keep Dry Use great care in operating your X Series around water The Remote Transmitter is sealed to be water resistant However if dropped into a puddle pond or creek it may become damaged The Remote Receiver should be protected at all times against water damage If your X Series runs into a body of water and the Remote Receiver becomes submerged the electronic circuit board inside will be destroyed When washing the unit avoid direct water contact with the Remote Receiver If the Remote Guidance System electronics are damaged by extreme exposure to water e g submerged in a pond the damage will not be covered under the manufacturer s warranty 2 H F 9 GU LU O Z lt g H F e 2 Lu D gt Figure 15 Confirm Command Indicator 1 When a signal is given
4. not authorize any other person or firm to assume for us any other liability or obligation in connection with the sale of this battery Shipping is the responsibility of the Owner NOTE This warranty is not valid for sales or use outside the U S A This warranty is voided if any charger is used that is rated higher than 6 amps or is not specifically recommended by Kangaroo Please inspect this battery upon receipt If you believe it is damaged call immediately at 1 800 438 3011 WARRANTY 54 Warranty ReadyPro Battery Charger Warranty expires on the ReadyPro Electronic Battery Charger one year from the date of shipment it to the original purchaser If the charger is defective Kangaroo may require its return to our plant prior to replacement The customer is responsible for UPS shipping charges on all returned items The KANOVA Charger is warranted to charge your Kangaroo Battery for an eighteen hole round of golf This warranty is void unless proper maintenance procedures are followed IMPORTANT Damage due to accident abuse or misuse and neglect is specifically excluded under this warranty This warranty supersedes any other warranties expressed or implied and is non transferable Kangaroo does not authorize any other person or firm to assume for Kangaroo any other liability or obligation in connection with the sale of this battery charger Features and manufacture s specifications are subject to change without notice
5. only My AutoBrake does not function Circuit board inoperative Return to Kangaroo for repair My Motor is running but the wheels 1 Transaxle gear train problem Return to Kangaroo for repair are not turning 2 Axle pin roll pin sheared One of the rear wheels will not stay attached Flex Adjust Bag Support keeps falling down My X Series gradually died as the round of golf progressed My battery seems okay but my X Series was sluggish at the beginning of play then died during my round It also struggles on steep slopes zogen ae Bronze bushing in the center of the wheel may not be fully seated 1 Yoke Stop is broken 2 Yoke Stop screw is broken The battery is no longer capable of powering your X Series an entire round To be certain swap batteries with a friend Possible motor failure Is the motor hot to the touch Gently tap the bushing back down to ensure it is seated in the hole as far down as it will go 1 Replace Yoke Stop 2 Replace Yoke Stop Screw Replace the battery KEEP YOUR BATTERY CONNECTED TOO THE KANOVA CHARGER AT ALL TIMES If the motor is hot to the touch it will have to be serviced or replaced It is normal for the motor feel warm TROUBLESHOOTING Ser emer ane My X Series suddenly stopped Possible broken battery wire Check the battery wire clips While during the round standing behind your X Series wiggle them to see if it will power up If
6. operation E Adjustable Umbrella by BirdiePal Variable adjustability of the shaft allows you to stand up straight underneath the umbrella when attached to your X Series no matter how tall you are Lightweight and nearly unbreakable due to its flexible fiberglass shaft and frame The Silver Metallic Umbrella has a UV protection factor of 50 F Umbrella Stand Holds a straight handle golf umbrella unique clip device secures it from flying off Attaches to the Umbrella Holder Mount that sits atop your X Series Scorecard Platform Optional Xtender available for tall golfers G Rain Cover Take the featherweight zero permeability Rain Cover out of a golf bag pocket to protect equipment from the rain It offers easy pocket access and a front to back or zip per Remote Guidance will still work and your X Series controls remain visible through a clear panel in the cover for those with manual operation OPTIONS H Sand amp Seed Holder Repair divots to help maintain your course s fairways The Sand amp Seed Holder fits your X Series model handle tubing and works best when mounted sideways on tubing for easy access Simple to install Comes complete with Sand Bottle Just fill with your golf course superintendent s divot repair mixture To order options for your X Series call 1 800 438 3011 or shop online at www KangarooOwner com 46 Internal view of the precision made transaxle with 4 power train gears plus 4 be
7. well designed with quality parts and full protection circuitry There are no user serviceable components Keep it Clean The only type of maintenance required for your X Series is cosmetic Use soap or mild detergent and water then rinse with clean water You MUST avoid getting water in the control plugs Your X Series can dry in the sun but the stainless steel tubing should be wiped dry for the best luster Never use an abrasive cleaner Stainless Steel Components amp Tires It is a good idea to use a quality automotive wax on the stainless steel to prevent fingerprints and smudges from showing up The X Series polyurethane tires are made of a compound unaffected by conditions that deteriorate ordinary rubber You may use a cleaner preservative such as Armorall or a similar product to keep tires looking like new Normal Wear amp Tear The handle grips and the Upper and Lower Black Bag Protectors may deteriorate with use This is normal wear and tear and is not covered by warranty Factory Warranty Service If you need repair or service please follow this procedure 1 Telephone or e mail the Kangaroo factory See page 6 of this manual for contact information 2 If Technical Service instructs you to return your X Series or any part of it pack in the original carton ora sturdy substitute container Enclose a note with your name address daytime phone number or e mail and description of the problem you discussed with Technica
8. with Industry Canada licence exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Le pr sent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence Lexploitation est autoris e aux deux conditions suivantes 1 appareil ne doit pas produire de brouillage et 2 Putilisateur de l appareil doit accepter tout brouillage radio lectrique subi m me si le brouillage est susceptible d en compromettre le fonctionnement Z Q lt 2 D LL Z Q S 6 LL Find us on f facebook
9. Confirm Command light stays on Using the Remote Transmitter both STOP and GO commands function but the LEFT and RIGHT commands do not function The front wheel does not turn Weak 9 volt battery in the Remote Transmitter Remote Transmitter keypad or circuit board needs replacing Loose cable connection between the Electronic Front Drive and the Remote Receiver Broken wire on front wheel servo motor 1 Replace the 9 volt battery It is recommended that you replace the 9 volt battery every three months 2 Return to Kangaroo for repair 3 Properly insert plug and set locking ring See page 12 Properly insert plug and set locking ring See page 11 Figure 4 4 Return to Kangaroo for repair TROUBLESHOOTING Ser Trape Teen My Electronic Front Drive wheel 1 The front wheel is misaligned Adjust the Centering Knob on the turns but will not center exactly 2 The centering sensor in the front Remote Receiver wheel is inoperative See pages 23 24 Return to Kangaroo for repair My Electronic Front Drive wheel will Steering motor timed out Turn the Function Switch OFF not return to center wait 5 seconds Return to Kangaroo for repair My Electronic Front Drive wheel The centering sensor in the front Return to Kangaroo for repair chatters and moves back and forth wheel is inoperative My X Series runs on fast Circuit board inoperative Return to Kangaroo for repair speed
10. Free Wheeling Mode ssssssssssnnsnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnmn n nn nnnnnnnnnnnn nanna nnen 35 Rear Wheel Assembly and Removal cccccceeeeeeeeeeeeeeneeeeesneeeeeeeeeeeeeeeeeeeeeeeeeaeneneenseeeeeseees 37 Battery amp Char reside ae ehe 39 Optional e Tel nennen nee 43 Lu Eer TE 47 Kette ee Ee EE EE 49 Warranty a 51 Troubleshooting in ehe 57 OU r 2 H F 74 e O LL O U l lt r o S gt Q m g Cc I Z al 0 I H y Z al What to do if a Kangaroo product or part is damaged during shipping Please call or e mail Kangaroo see Contact Information on page 6 with your invoice number and customer number Specify which product or part is damaged Do not return the damaged products or parts back to Kangaroo we will contact the shipping carrier to file a claim Kangaroo will send replacements The shipping carrier is responsible for picking up the damaged merchandise if they choose to and sending the item back to Kangaroo Do not dispose destroy any carton or packing material in which merchandise was shipped The carrier may contact you for an inspection visit or send a pickup for the merchandise Contact Information Kangaroo Products Company 111 Kangaroo Drive PO Box 607 Columbus North Carolina 28722 0607 Phone 800 438 3011 or 828 894 8241 Fax 828 894 2718 E mail Walk KangarooGolf com To order parts and accessories visit www KangarooOwner com Kangaroo
11. Front Drive Any failure that is the result of a defect in material or workmanship is covered by the warranty The original Owner is entitled to a no charge repair or replacement at Kangaroo s discretion for 12 months from the date of purchase Components covered by the warranty are the motor power train wheels tubing and all electronics Necessary labor will also be at no charge All warranty repairs must be performed at Kangaroo s factory in Columbus North Carolina Warranty Hillcrest X Gel Deep Cycle Battery Warranty expires 12 months from the date of shipment For this reason it is recommended to buy your battery only at the time of need The battery purchased from Kangaroo for use on the X Series is guaranteed to power for eighteen holes of golf on any course for a period of one year Batteries which have been subject to abuse physical damage improper storage or improper maintenance are not covered Batteries that fail to hold a charge within 12 months from the date of shipment will be replaced on a pro rata basis computed from the date we are informed of the problem If the battery fails please call Kangaroo s Service Department for instructions The pro rata value will be based on the current price of the battery which replaces the defective one Kangaroo reserves the right to require return of this battery to our plant prior to replacement This warranty supersedes any other warranties expressed or implied We do
12. Function Switch to OFF and remove the obstruction Turn the power back ON The wheel should now automatically align itself If it does not re adjust using the centering knob as shown on this page Cont 2 H ke 9 GU LU O Z lt g H F e 2 Lu D S The centering and directional control in the Electronic Front Drive can be damaged if the unit rams into any obstacle When your X Series must be maneuvered in close areas it may be best to do so manually for instance across bridges around trees or in parking lots X Series includes a Bumper Guard to help protect the centering device Damage caused by hitting obstacles is not covered under the manufacturer s warranty All Remote Guidance System units must be returned to Kangaroo for proper repair There are no user serviceable components inside Electronics Remote Receiver and Remote Transmitter Remote Receiver The Remote Receiver is the main control center of the Remote Guidance System It processes and relays all of the signals from the Remote Transmitter to the Electronic Front Drive Automatic Safety Shut Off The Remote Receiver is designed to receive a signal from the Remote Transmitter every 28 to 30 seconds If for any reason the unit does not receive a signal within this time span it will automatically shut off The auto shut off will also stop your X Series if it gets out of signal range This is a required safety function to prevent runaway In normal use
13. Kangaroo Hillcrest A Series Remote Sportcaddies for the Serious Golf Athlete Made in USA Model Serial Important Visit www KangarooOwner com warrantycardform html within 30 days of purchase to register your warranty Thank you Dear I am sure you are looking forward to many enjoyable rounds on the golf course with your new X Series To make absolutely sure you do a team of us carefully put together this easy to use Owner s Manual which includes operating and maintenance instructions warranty information and helpful tips on how to keep your X Series looking new and running smoothly Before your X Series was shipped it was given a special pre delivery inspection and operational test all parts being checked and aligned to ensure it is ready for the golf course However if you discover something faulty or have questions don t hesitate to give me a call On behalf of the entire Team at Kangaroo Products Company THANK YOU VERY MUCH Sincerely P S Enclosed is my business card Feel welcome to pass it along to a fellow golfer who may be interested in purchasing an X Series Hillcrest ABX Hillcrest MAX Table of Contents Reporting Damage During Shipping s seeeeeeeeeeeeeeeeeeeeeeeeeeeeeeneeeeeensnesnseessseeeeeeeeeeeneeees 5 Contact IMPOMMALI E 6 VISIE KANGOO isso 7 A o lt A A 9 Power Controls amp Operation aus aiaiddda dada diinida 17 Remote Ee EE E 23 AUtOBraKE it 33
14. This product is solely for use with a Kangaroo X Series Motorcaddie Warranty Equipment Warranty expires on Kangaroo Xtreme Slope Wheel Gallery Seat Scorecard Platform Ball amp Club Washer Mount for Remote Transmitter Swivel Cup Holder Sand amp Seed Holder Umbrella Stand and Extender for Umbrella Stand 12 months from the date of shipment to the original purchaser Warranty expires on Kangaroo Rain Cover Battery Carrying Case Adjustable Umbrella 12 months from the date of shipment to the original purchaser If the equipment is defective Kangaroo may require its return to our plant prior to replacement The customer is responsible for UPS shipping charges on all returned items If the equipment is defective Kangaroo may require its return to our plant prior to replacement The customer is responsible for UPS shipping charges on all returned items IMPORTANT Damage due to accident abuse or misuse and neglect is specifically excluded under this warranty This warranty supersedes any other warranties expressed or implied and is non transferable Kangaroo does not authorize any other person or firm to assume for Kangaroo any other liability or obligation in connection with the sale of this battery charger Features and manufacture s specifications are subject to change without notice WARRANTY 56 Troubleshooting My Remote Guidance System does not function All connections are made properly and the Confirm
15. d in relation to the Accelerator position Figure 8 Note Turning the Accelerator all the way down does not turn off Power Controls even if your X Series is not moving There is a feature known in technical terms as ramp up that automatically provides a gentle start at any setting up to and including full speed Even so your X Series is very powerful and it is best to start out at lower speeds Function Switch The Function Switch is located on the top center of the handle Figure 9 e Switch to the MANUAL mode when remote control is not desired e Switch to REMOTE mode when you are ready to resume play with Remote Guidance Y 74 H F lt L LU A O a Z lt N l e CL E e e O Co RIGHI Figure 10 Normal Operation 1 Prior to beginning play rotate the Accelerator to the SET position Figure 8 on page 17 You can vary the Accelerator to suit your own walking pace after you begin play 2 Position the Function Switch to ON Figure 9 on page 17 3 Position the Function Switch to the MANUAL position when Remote Guidance is not desired Manual Mode is recommended when using your X Series in parking lots in tight spots and around water hazards 4 Position the Function Switch to the REMOTE position when you are ready to begin play with Remote Guidance 5 Press the GO button on the Remote Transmitter Your X Series will start and ramp up to your preset speed Press GO a second time and
16. e 26 toward Asheville North Carolina After entering North Carolina take exit 67 North Carolina Highway 108 and follow the signs to Columbus Kangaroo will be 1 1 miles on the LEFT e O CL lt g E O F Y Z H F al U O Hillcrest AB Assembly Components A Chassis B Electronic Front Drive C Upper Caddie Structure ASSEMBLY Figure 2 Figure 1 Assembling your X Series Motorcaddie Your Kangaroo X Series Motorcaddie is shipped without the rear wheels attached See pages 37 and 38 for rear wheel assembly and removal instructions 1 Steady the Chassis by using the hand hold located in the bottom of the battery tray Insert the Electronic Front Drive into the hole located in front of the battery tray and close the draw latch Figure 1 Note The Upper Caddie Structure and Electronic Front Drive will fit in either hole therefore be sure the motor is on the top right side while standing behind the X Series 2 Insert the Upper Caddie Structure into the top of the Chassis just behind the battery tray and close the draw latch Figure 2 3 Fold down the Flex Adjust Bag Support Figure 7 on page 15 until it comes to a stop 4 Remove the three plastic tie wrap bands from the handle Simply press down on each of the red tabs on the ASSEMBLY tie wraps that are encircling the handle grips While pressing down on the red tab push the extended edge back through the locking mechan
17. f the unit does cause harmful interference to radio or television reception please refer to your user s manual for instructions on correcting the problem INSTRUCTION TO THE USER This equipment has been tested and found to comply with the limits for a class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Consult the dealer or an experienced radio TV technician for help Operation with non approved equipment is likely to result in interference to radio and TV reception The user is cautioned that changes and modifications made to the equipment without the approval of manufacturer could void the user s authority to operate this equipment Industry Canada Information This device complies
18. heel all the way against the hub aligning the drive pins on the hub into the drive holes in the wheel When the wheel is on the axle against the hub with drive pins engaged release the tab Figure 21 This will allow the release tab to lock into the Drive groove and the wheel should now be securely mounted on the axle Wheels should NOT slide off the axle To remove the wheels pull the release tab back toward the tire and slide the wheel off axle Wheels are not left right specific and can be installed on either side gt O 2 m x 7 m 2 m o lt d m m ae z 18 wi M x 8 Figure 22 Figure 24 Ze PO Y Figure 23 Battery amp Charger Before Using Your Battery The Hillcrest X Gel Deep Cycle Battery is shipped in an 80 charged state Prior to your first round of golf we recommend a full 12 hour charge when you receive the new battery To Charge Your X Series Battery with the ReadyPro Electronic Charger 1 Disconnect the battery from your X Series Figure 22 Or if this is your first time charging your battery be sure to remove the safety cap Figure 23 2 Be sure the charger is UNPLUGGED from the wall when connecting or disconnecting the battery Doing so will avoid sparks or shocks and will reset the charging circuits 3 Connect the RED battery clip on the charger to the POSITIVE terminal on the battery Connect the BLACK clip to the NEGATIVE terminal on the battery Figure 24
19. ic Front Drive is loose turn the draw latch metal adjustment ring clockwise to tighten Do not over tighten the adjustment ring as this may cause the draw latch to break when engaged If the draw latch will not lock in place loosen the draw latch by turning the metal adjustment ring counter clockwise Figure 6 Note The metal adjustment ring may be difficult to turn A standard pair of needle nose pliers can be used to make adjustments To avoid possible breakage always close draw latches before placing Chassis into your car Flex Adjust Bag Support The Flex Adjust Bag Support on the Upper Caddie Structure Figure 7 also referred to as the yoke is designed to fold up for easy transportation and storage It can be adjusted to grip your golf bag by bending the arms open or closed as needed ASSEMBLY The Flex Adjust Bag Support is attached to the stainless steel tubing at the best position to hold most golf bags securely If you have an unusual bag or a personal preference for its position its clamp can be moved up or down the tubing to any point you like The Bag Support is secured with four 5 32 Allen type machine screws and a suitable wrench is provided with your X Series Simply loosen the four screws and adjust the clamps accordingly then re tighten securely Figure 9 Figure 8 Power Controls and Operation Accelerator Speed is controlled by the Accelerator located between the handle grips The decal indicates spee
20. is safeguard turn the Function switch OFF each time you stop Merely turning the speed all the way down will not reset this internal timer and will cause your X Series to unexpectedly shut off If you forget and your X Series unexpectedly cuts out or is dead turn the Function Switch to OFF and then back ON to restart your X Series Y 74 H F lt L LU A O a Z lt N md e CL E e e O N un Figure 12 Figure 14 Figure 13 Remote Guidance System Remote Guidance System consists of three components the Remote Transmitter Figure 12 Remote Receiver Figure 13 and Electronic Front Drive Figure 14 Remote Guidance System operates on an FM Pulse Code Transmittal System that is FCC approved and requires no operator s license Remote Guidance System is relatively low power milliamps and is subject to little outside interference Remote Transmitter and Remote Receiver devices comply with Part 15 of FCC rules Operation of these devices is subject to the following two conditions 1 The devices may not cause harmful interference and 2 The devices must accept any interference received including interference that may cause unintended operation The antenna is permanently mounted inside the Remote Receiver to make it more water resistant You should not attempt to open the Remote Receiver doing so will break the seal and void the warranty Activating Remote Guidance System See Power Contro
21. ism to loosen the hold on the handle grip Note Make sure the Function Switch is in the OFF position Begin to establish the habit of putting the switch in the OFF position while assembling your Kangaroo X Series Cont Figure 3 Figure 5 Figure 4 5 Connect the plug from the Upper Caddie Structure to the receptacle in the Chassis Figure 3 Note Always handle the plug when connecting or disconnecting the control cable Pulling on the wire can cause damage 6 Connect the Electronic Front Drive by inserting the black plug into the receptacle on the lower left of the Remote Receiver Push inward on the lock ring while twisting it clockwise until it stops Figure 4 7 Remove the black plastic cover not shown from the battery terminal Set the battery into the battery tray with the terminals to the back of battery tray Figure 5 a Connect the RED clip to the positive terminal b Connect the BLACK clip to the negative terminal Note If the cables are accidentally reversed your X Series will not run until the polarity is corrected Your X Series is equipped with reverse polarity protection and connecting the terminals backwards ASSEMBLY will not harm you or the unit Adjustments Your X Series comes with an assortment of Allen type wrenches They are provided for adjustments keeping screws tight and for adding optional equipment Draw latch If the Upper Caddie Structure or Electron
22. ition each wheel into Free Wheeling Mode pull the release tab on the inside of the wheel towards the tire Figure 19 Slide the wheel outward slightly on the axle Position the wheel so that the release tab is in the Free Wheel groove Release the tab to allow it to lock in the proper groove The wheel should spin freely Hub drive pins will no longer be engaged into the wheel s drive holes Now try to move the wheel outward on the axle to ensure the release tab is locked The wheel will NOT slide off the axle if properly positioned Returning Wheels to Drive Mode While pulling the release tab slip wheel all the way against the hub aligning the drive pins on the hub into the drive holes in the wheel When the wheel is on the axle against the hub with the drive pins engaged release the tab This will allow the release tab to lock into the drive groove The wheel should now be securely mounted on the axle Figure 19 g Z l LU LU I gt LU Lu ec LL Figure 21 Figure 2O Rear Wheel Assembly and Removal Both rear wheels on your X Series may be easily removed and replaced Wheels are held in place by a spring loaded release tab on the inside of each wheel The tab seats into a groove on the axle There is a groove for the Drive position and one for Free Wheeling Mode To install the wheel on the axle pull the wheel release tab back Figure 20 While holding the release tab place the wheel on the end of the axle Slip w
23. l Service Any parts and services provided under warranty do not extend the original warranty Any out of warranty service including parts and labor is warranted for 60 days If the service is not under warranty please specify whether you would like Kangaroo to invoice you or charge to your credit card including all numbers and the expiration date of your card ARS Service When shipping your X Series to the factory for repairs save money by requesting Authorization Return Service ARS ARS provides for the easy shipment of UPS compatible packages Pre printed UPS return labels are available from Kangaroo at a reasonable price ARS labels can be mailed or sent via e mail X Series Warranty Registration Visit www KangarooOwner com warrantycardform html within 30 days of purchase to register your warranty Lu O Z lt Z m Z lt 2 Warranty at a glance Chassis Wheels Upper Caddie Structure 60 Months Remote Guidance System RGS and Electronic Front Drive 12 Months 12 Months Hillcrest X Gel Deep Cycle Battery Pro Rated ro Rate ReadyPro Electronic Battery Charger 12 Months Xtreme Slope Wheel Gallery Seat Scorecard Platform Ball amp Club Washer Mount for Remote Transmitter Swivel Cup Holder Sand amp Seed Holder Umbrella Stand and Extender for Umbrella Stand 60 Months Rain Cover Battery Carrying Case Adjustable Umbrella 12 Months Warranty Wheels amp Upper Caddie Structure Any fai
24. ls amp Operations on page 18 2 H ke 9 GU D O Z lt g H F e 2 Lu D N Figure 15 Centering the Steerable Front Wheel Before you begin play the front wheel must be centered so your X Series will track straight Use the centering knob Figure 15 on the rear of the Remote Receiver to adjust the front wheel Do not attempt to turn the front wheel by hand The front wheel must be centered electronically by turning the black knob The knob is very sensitive Rotate it slowly to adjust the front wheel right or left as needed When the front wheel is centered the knob can be turned slightly right or left without the wheel moving If the wheel is not centered any turn of the knob will cause the wheel to swivel Automatic Self Centering Front Wheel Remote Guidance System s built in centering control will automatically center the front wheel every time you stop transmitting a directional signal with the Remote Transmitter The centering function will not work properly unless you center the front wheel using the electronic centering knob as described above During normal operation a sensor in the Remote Guidance System detects course conditions and allows for small terrain deviations thus allowing your X Series to follow a straight line of travel If for any reason the front wheel becomes jammed and cannot return to center the self centering feature will shut off after 6 seconds To dislodge the obstacle turn the
25. lure that is the result of a defect in material or workmanship is covered by the warranty The original owner is entitled to a no charge repair or replacement at Kangaroo s option for 60 months from the date of purchase Components covered by the warranty are the motor power train wheels tubing and all electronics Necessary labor will also be at no charge All warranty repairs must be performed at Kangaroo s factory in Columbus North Carolina TO ACTIVATE YOUR WARRANTY See pages 1 and 50 EXCLUSIONS Exclusions to the warranty coverage include damage from shipment to Kangaroo normal wear and tear hairline cracks in structural parts not affecting X Series operation neglect abuse or accidents damage by persons other than the Owner or utilization for any purpose other than carrying golf bags on golf courses TRANSFERRING YOUR WARRANTY The X Series warranty is not automatically transferable If your X Series is sold the new Owner can purchase the remaining warranty for 2 per month remaining on the warranty To transfer the warranty the new Owner must contact Kangaroo request the warranty transfer and provide proof of the original purchase IF YOU NEED WARRANTY SERVICE All warranty repairs MUST be performed at Kangaroo s factory in Columbus North Carolina All shipping charges inbound and outbound are the responsibility of the Owner WARRANTY 52 Warranty Remote Guidance System RGS amp Electronic
26. ode is sufficiently low to ensure that the battery will not be over charged Explanation of Charger Lights e If RED light only is illuminated charger is on and battery is charging but NOT READY for use The length of time will depend on battery s level of discharge the more it s discharged the longer the RED light will stay illuminated e If RED AND GREEN lights are illuminated at the same time your battery is ready for 9 HOLES of use This status lasts approximately 20 minutes to one hour before battery is fully charged e If GREEN light only is illuminated battery is fully charged and is ready for 18 HOLES of use Indications that Your Battery Needs Replacement e If you never get the GREEN light even after 24 hours of charging you know that your battery has a dead cell The battery can no longer achieve a full charge and should be replaced when it can t power your Kangaroo Sportcaddie for 18 holes e Ifthe GREEN light is illuminated after a charging cycle but you no longer get 18 holes of sufficient power your battery has sulfated with age and use Your battery is being recharged to full voltage but it no longer has sufficient capacity to power your Kangaroo Sportcaddie for a round of golf Maintenance The Hillcrest X Gel is a maintenance free sealed battery Warranty See pages 54 55 Troubleshooting Problems See pages 57 62 Purchasing a Replacement Battery or ReadyPro Charger To purcha
27. ries will slow down and give you a feeling of security as you travel down the hill If the slope is extremely steep you may turn the Function Switch OFF which will provide approximately 50 more braking power than just turning the Accelerator to its slowest setting If this is too much braking power alternate turning the Function switch OFF and ON until you reach the bottom of the hill IMPORTANT If you must tow your X Series either forward or backward always place it into Free Wheeling Mode FIRST Gear damage may result from pulling or pushing your X Series with great force or for long distances Damage incurred from failure to disengage drive wheels from gear train is NOT covered by warranty See Free Wheeling instructions on page 35 amp 36 AutoBrake is not intended to stop your X Series Rather it is used for decreasing speed when going down hills AutoBrake does not function as a parking brake Therefore always make sure your X Series is turned sideways when stopped on a slope Lu x S m O s m lt Figure 19 Free Wheeling Mode Free Wheeling means that the two drive wheels on your X Series turn freely without engaging the axle or drive train If you must tow your X Series either forward or backward ALWAYS place it in Free Wheeling Mode first Gear damage will result from pulling or pushing with great force Damage from failure to disengage the drive wheels from the gear train is not covered by the warranty To pos
28. s worldwide headquarters is located just one mile from interstate 26 40 miles southeast of Asheville North Carolina and 30 miles northeast of Spartanburg South Carolina e H F lt 2 a e H Z ke lt ke Z O O To Asheville US Hwy 74 a Kangaroo Products Exit 67 111 Kangaroo Drive ZI Exit 163 NC Hwy 108 to Mill Spring and Rutherfordton To Tryon Exit 67 NC Welcome Center To Spartanburg Visit Kangaroo From Asheville North Carolina via Interstate 26 Follow Interstate 26 east toward Spartanburg South Carolina Take exit 67 US 74 toward Rutherfordton Follow US 74 approximately one mile to exit 163 then turn RIGHT toward Columbus Kangaroo will be 1 2 mile on the RIGHT From Charlotte and Gastonia North Carolina via Interstate 85 and US 74 Follow Interstate 85 south toward Spartanburg South Carolina Take exit 10B US 74 toward Kings Mountain and Shelby Follow US 74 approximately 69 miles to exit 163 At exit 163 turn LEFT toward Columbus Kangaroo will be 1 2 mile on the RIGHT From Columbia and Spartanburg South Carolina via Interstate 26 Follow Interstate 26 west toward Asheville North Carolina After entering North Carolina take exit 67 North Carolina Highway 108 and follow the signs to Columbus Kangaroo will be 1 1 miles on the LEFT From Atlanta Georgia via Interstate 85 Follow Interstate 85 north toward Greenville South Carolina Take exit 70A Interstat
29. safe Your new X Series is nota toy Always use common sense while operating 2 H F 9 GU D O Z lt g H F D 2 LU D amp Figure 16 Figure 17 y T e S Figure 18 Manual Steering Operation To operate your X Series in Manual Mode Press the Remote Transmitter s STOP button Then turn the Function switch to MANUAL Adjust the Accelerator if necessary Padded Case for Remote Transmitter Included with your new X Series is an attractive Padded Case screenprinted with Kangaroo logo Figure 16 It can be worn two ways 1 Looped over a belt with the back flap secured by the Velcro 2 Slipped over the waistband of pants or a skirt Try it both ways to decide which you prefer The Padded Case s long back flap is stiff enough to hold the Remote Transmitter secure When you put your Remote Transmitter away flip the long flap forward secure with Velcro and store in a safe dry place Remote Transmitter Swivel Clip System amp Belt Clip The Remote Transmitter Swivel Clip System standard on both MAX and ABX mounts securely to the Scorecard Platform Figure 17 The included Remote Transmitter Belt Clip can also be worn on your belt pocket or golf bag Figure 18 2 H F 9 GU D O Z lt g H F D 2 Lu D R Hillcrest ABX AutoBrake Operation As your X Series travels downhill with the power switched ON turn the Accelerator downward to a slower setting Your X Se
30. se a replacement Hillcrest X Gel Battery or ReadyPro Charger visit www KangarooOwner com or contact Kangaroo at 1 800 438 3011 EL UI g lt L O gt KL E lt D Options A Xtra Gear Basket Attractive lightweight mesh basket attaches quickly and comes in handy when carrying a sweater or snack The wedge shaped mounting clip makes this roomy basket 12 x 8 inches by 8 inches deep easy to remove Black parts are electro statically powder painted for durability B Ball amp Club Washer This washer mounts in the seat bracket on your X Series When you finish golfing just slide the washers blue L bracket out of the chassis mounting bracket If your X Series already has a seat bracket no installation is needed If you don t already have a seat bracket chassis brackets are available separately C Gallery Seat Mounts easily to your X Series The seat provides a perfect spot for a quick break or to wait your turn The bracket is OPTIONS attached securely to your chassis for outstanding stability The cushion is molded by Kangaroo of puncture proof integral skinned polyurethane foam more durable than rubber or vinyl withstands rain ozone and ultraviolet rays D Xtreme Slope Wheel Standard on the MAX Offers added stability on steep inclines When your X Series tilts back the wheel arm automatically pivots out preventing an embarrassing tip over Easy to install Recommended for remote control
31. the red Confirm Command light Figure 15 on the Remote Transmitter will flash twice once with the pressing of the button and again when the button is released confirming your command NOTE The buttons are easy to press There is no need for excessive force When the indicator light flashes the signal has been sent 2 When the 9 volt battery is weak the light will stay on continuously indicating the 9 volt battery must be replaced Remote Guidance System may have a loss of signal strength and a loss of range when the Remote Transmitter battery is weak To test the battery press and hold any function button If the light stays on while the button is depressed the battery is weak and should be replaced The position of the Remote Transmitter is important during signal transmission In order to achieve maximum range hold the Remote Transmitter with the control buttons on top and the back of the Remote Transmitter toward the ground Point the front of the Remote Transmitter toward your X Series The Remote Transmitter will operate if held in other positions but the overall operating range will be decreased The range will also be affected if there are obstacles between you and your X Series such as trees buildings cars etc Play it Safe Expect an orientation period to learn the controls of the Remote Guidance System Do not try to learn the controls in close quarters Never try to operate your X Series while it is out of your sight Play it
32. veled differential gears enabling easy turning and Automatic Braking Technical Specifications Motor High torque 2 pole armature permanent magnet 12 volt DC Drive Train Double reduction sealed maintenancefree self lubricating gear drive with differential and direct drive hubs Controls All solid state motor control 45 amp capacity all circuitry under overcurrent and reverse polarity protection Remote Guidance System Maximum Range of Go Stop Time Lapse from Turn Button FCC ID Operation 100 yards Release to Straight Ahead OVPTX600 845C 2 Seconds OVPRX600 840C Maximum Range of Directional Operation 50 yards Turning Radius Component Weight on pavement 16 Feet Electronic Front Drive T1lbs Maximum Turning Angle of X Series 20 Replacement Transmitter Battery Alkaline Battery 9 Volt Hand Held Transmitter 5 oz Time Lapse from Straight Ahead to Full Turn 2 Seconds Radio Operating Frequency Range 903 37 921 37 MHz All parts and specifications subject to change without notice Radio Receiver Module 12 oz OU Z H F lt Q O LU A GU l lt 9 Z L H H F amp Maintenance Don t Oil it Your X Series has been designed and manufactured to be essentially maintenance free Do not open or attempt to service the transaxle gear train It is tuned at the factory to minimize gear noise It also contains a special lubricant which is sealed inside by a gasket The control system is
33. your X Series powers up then you have a broken wire somewhere on your battery clips To check the battery wires open the crocodile clips and clip them onto an object 34 thick so they are held in the open position Then slide the black red rubber covers back to inspect the metal clip Solder the joint and wire or replace the battery wires HINTS If you still have problems after consulting this troubleshooting guide and following its directions please call our Technical Service Department at 1 800 438 3011 Important Kangaroo strongly recommends you contact Technical Service prior to making any repairs Always replace the Remote Transmitter 9 volt battery every 3 months with a good quality Alkaline 9 volt battery g F e e L N wu m e CL E TRADE NAME Remote Guidance System Receiver MODEL NUMBER RX600 840D COMPLIANCE TEST REPORT NUMBER B40609D1 raumow CCC This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation I
34. your X series will increase its speed automatically ramping up to 90 of its maximum speed approximately 4 5 mph Press GO a third time and your X Series will automatically decrease to your original preset speed If you press GO a fourth time your X Series will again increase to 90 of its maximum speed Each activation of GO while your X Series is moving will alternate between your preset speed and 90 maximum speed Figure 10 Cont Y 74 H F lt 18 Lu A O a Z lt N md e CL E e e O S Figure 11 6 To stop your X Series press STOP on the Remote Transmitter To achieve maximum braking the Function Switch must be turned OFF There is no need to change the accelerator when stopping and re starting Figure 11 Reminder The arrows on the Remote Transmitter indicate steering direction as if you were operating your X Series manually If your X Series is coming toward you the steering direction of the arrows are reversed 7 If you stop your X Series on a hill always turn it across the slope to park it The X Series models do not have a parking brake and will creep down a hill on their own Runaway and Circuitry Protection Your X Series will automatically shut itself off if the Function switch is left in Remote or Manual position for an extended period of time The reason for this is to prevent a possible runaway situation This also allows the solid state circuitry a cool down period To avoid activation of th
Download Pdf Manuals
Related Search