DMX-16SW SYS(DP-415x2+DMX-16S
Contents
1. DMX signals 4 Power Supply Port Used to connect the Adaptor Power Switch When in power put the power on or off2. in HTP mode that is in link condition it output the bigger value DMX data input and DMX data output Figure 1 If you are making your between the inputted DMX 512 signal and the 16 channels value which corresponds own cables be sure to use standard two conductor shielded cable This to the device s address cable may be purchased at almost all pro sound and lighting stores Your cables should be made with a male and female XLR connector on either Figure 1 end of the cable Also remember that DMX cable must be daisy chained and can not be Y ed or split Notice Do not use the ground lug on the XLR connector Do not connect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behavior DMX 16SW SYS Dimmer Pack DP 415 Notice Be sure to follow figures two and three when making your own cables COMMON ce om conons ON DMX Nponmouer Figure 2 The DP 415 is a hybrid 4 channel pack designed to both dim and switch Dip switch number PON ETR J wmx OY CONN TOR 10 on the pack functions as the mode switch When it s set to On the pack will operate in Switch mode When it s set to Off the pack will operate in Dimmer mode Whenever using these packs to control Par Cans or any other type of conventional effect fixture with no ea ea Sa transformer dip switch 10 should be left OFF so to fu
3. products New products are constantly being designed to meet the needs of the entertainment lighting industry Your comments regarding our products and services are welcome Elation Professional will provide set up help and to answer any question should you encounter problems during you set up or initial operation You may also visit us on the web at www elationlighting com for any comments or suggestions And please send us an e mail to info elation lighting com and let us know how to improve to better serve you It is both a privilege and a pleasure serving you Service Hours are Monday through Friday 8 00 a m To 5 00 p m Pacific Standard Time Voice 800 322 6337 Fax 323 582 2610 E mail support elationlighting com Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures warranty In the unlikely event your unit may require service please contact your nearest Elation Professional dealer Do not discard this carton in the trash please recycle when ever possible Upon unpacking carefully inspect your unit for any damage that any have occurred during shipping If damage may have occurred do not plug the unit in please contact your dealer as soon as possible Be sure to use a proper ground connection for all DP 415 s Do not remove or break off the ground prong from the electrical cord The ground is used to reduce the risk of electrical shock f
4. CUICH ON MAREE EEE E AA 1 ONDA KINO e E E 1 Customer SOO icetneeecencnniteossnacansmigueeteeenennaans 1 RUIN OU anae AE EA EE 1 MN PENN e E aces 2 Connection amp Setup cccccseeeeeceeeeeeeeeeeeeeeees 3 4 DMX 16SW SYS Controller DMX 16SW DMX 16SW features c cccccececcececcccececeececeaesceass 5 Controls amp FUNCTIONS cccececececcececececeueueaceceneneass 5 Operation GUICe ccccecceecceeeeseeeeeseeceeeeeeeteeeteeeaes 6 DMX 16SW SYS Dimmer DP 415 FOAMING E E E AE 6 Controls amp FUNCTIONS 0 ccccceeeeececeeeeeececececeeeeeees 7 8 DMX AdCTreSSING c ccceccceecsseceeeceeecuecaeecseeeeesaees 8 9 Technical Specifications cccccsecseeseeseeeeseeneees 10 Dip switches 1 9 are in place so a DMX address can be assigned to the pack Dip switch 10 functions as a mode switch that allows you to select how you want the pack to operate When set to On the pack will operate in Switch mode When set to Off the pack will operate in Dimmer mode Switch 1 2 3 4 5 6 7 8 9 10 Aud Value 16 32 64 128 256 Binary DMX Address As the above illustration shows each dip switch represents a DMX value The top row of numbers is the dip switch number and the bottom row is the value for each dip switch Simply flip the desired dip switch or switches to the ON position for which the binary values add up to your desired address For example if your trying
5. Technical Specifications DMX 16SW Power Inputl DMIX 16S W iscsn dics ct osnectetomteteustaiciedinndicectemetatewecs DC 9V 200 mA min OMA Msg es areatee eee ee se tees ose pen bees be oe eae ee ede ae soe yesh eee a 3 pin XLR male DMA O10 19 0 eee ee ee ee ee eee eee eee eee neers te eee oe 3 pin XLR female EY TENG SS tS srs ads cae eget ges ese eed enc eek aee eee cee ue seen ees coon ea eees 482x82x44mm WY CBM EEEE E EEEE ET EE T tan eet TE N toads TETEE TAA ENE 2 3kg PLCC OS 5 OFC ab acs hol ose ada EEE pas EE EREE Er NAER SES An external Adaptor DP 415 Power Input DP 415 cccccccccccseececceeeeeseeceeseeeeeseaseeseaeeeseeessaaees AC120V 60Hz 15A Max DMA OUMU eeneennenteme ete ane a E e weno e een Sere e mere eres 3 pin XLR female BANGIN sth cies bes a E E EEEE E a 3 pin XLR male Fuses Internal ccccsssececcssecececeseeeeceeuseeesesesessueseessaegsessssases 6A 250V 5x20mm x 4pcs EE E AIE E EE E E T A A E A EE AA A STEE AE A EEN 180 x177 x 64 Wo erena E E E E EEE E N 1 4kg Special Note Improvements and changes in specifications and design to this manual and the unit may be made at any time without any prior written notice Elation Professional 4295 Charter Street P N 24 004 2352 00 Los Angeles CA 90058 Rev1 0 www elationlighting com PROFESSIONAL DMX 16SW SYS DMX 16SW DMX Switch Controller DP 415 4 Channel DMX dimmer switch pack USER MANUAL About the DMX 16SW SYS HIF O
6. annel number Each channel is rated at 5A Up to 15A can be ON at a time 2 Channel output LEDs 1 4 These four LED s indicate corresponding channel intensity 3 Power indicator This LED should be lit when the pack is powered ON 4 Dip switches Dip switches 1 9 should be used to set the packs DMX address Dip switch 10 should be used to set the packs operation mode When set to On the operates in Switch mode When set to Off the pack operates in Dimmer mode 5 DMX indicator This LED flashes when DMX signal is present Operation Guide Connection amp Setup Power Supply Before plugging your unit in be sure the source voltage in your area matches the required voltage for the DMX 16SW SYS Be sure to plug your power supply into a wall outlet with matching power before attempting to operate And complete the system connection by using 3 pin Power data extension cables 1 The dip switches1 9 are used to select the DMX start address which are corresponding to the 16 channels 2 Those 16 switches can shift between ON and OFF which can be indicated by the corresponding LEDs When a LED is on it indicates the corresponding switch is in ON mode the corresponding DMX value is255 when a LED is off it indicates the corresponding switch is in OFF mode the corresponding DMX value is 0 Data Cable DMX Cable Requirements Your controller and packs require a standard 3 pin XLR connector for 3 When the device is
7. nction in Dimmer mode Each of the e g 2 Cold 2 Cold I l packs four channels can hold a load of up to 5 amps This is roughly equal to 600 watts It is l very important to distribute the load evenly so to not blow a channel fuse Each channel is l Figure 3 I l internally protected with a 6amp 250V midget fuse Each channel also features dual Edison aa multiple lights can be plugged directly into the pack without having to use a tri tap ant r plug bar Qe eee ee Special Note Line Termination Features When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior A terminator is a 120 ohm 1 4 watt resistor which is connected between Compact 4 channel DMX dimmer switch pack pins 2 and 3 of a male XLR connector DATA and DATA This unit is inserted in the female USITT DMX512 1990 multiplexed digital control via 3 pin XLR connector XLR connector of the last unit in your daisy chain to terminate the line Using a cable terminator Dual 15A Edison plugs per channel will decrease the possibilities of erratic behavior On Off power switch 3 pin XLR In Out Termination reduces signal errors and avoids signal transmission problems 10 position dip switch setting and interference It is always advisable to connect a DMX terminal Resistance Hanging bracket to hang on truss or rig to clamp 120 Ohm 1 4 W between PIN 2 DMX and PIN 3 DMX of the last fixture LED powe
8. or fire Do not allow for any liquids to spill into or onto your unit Be sure that the local power outlet match that of the required voltage for your unit Do not attempt to operate this unit if the power supply cord has been frayed or broken Be sure to route your power supply cord out of the way of foot traffic Disconnect from main power before making any type of data connections Do not remove the top cover under any condition There are not user serviceable parts inside Disconnect the unit s main power when left unused for long periods of time Never plug this unit into a dimmer pack Always be sure to mount this unit in an area that will allow proper ventilation Allow about 6 15mm between this device and any surrounding walls or objects Do not attempt to operate this unit if it becomes damaged in any way Never operate this unit when its cover is removed To reduce the risk of electrical shock or fire do not expose this unit rain or moisture Controls amp Functions Front panel view 2 CAUTION 3 Risk of electric shock Disconnect input power Before opening N ouvrez pas risque de choc electrique Warning This unit must be grounded Power input AC 120V 60Hz 15A Max Output 5A CH Total 15A Max Loading fuses internal F6A 250V 5x20mm x4pes 1 2 3 4 O O MONITOR 1 Dual Edison Output sockets There are four dual Edison output sockets Each socket is labeled with its relevant ch
9. r ON indicator Channel intensity LED indicators 5 Amps per channel 15 Amps maximum ON at a time DMX Signal Cable 120 ohm impedance DMX signal cable MUST be used for signal connection 5 Pin XLR DMX Connectors DMX 16SW SYS Controller DMX 16SW Some manufactures use 5 pin XLR connectors for DATA transmission in place of 3 pin 5 DMX 16SW features include pin XLR fixtures may be implemented in a 3 pin XLR DMX line When inserting standard 5 l pin XLR connectors in to a 3 pin line a cable adaptor must be used these adaptors are pein Ee PAI pE ee digital control via 3 pin XLR connector readily available at most electric stores The chart below details a proper cable conversion 16 switches which can be switched between on and off Power Requirement DC9V 200mA Min Dimensions 482x82x44mm 3 Pin XLR to 5 Pin XLR Conversion Weight 2 3kg Conductor 3 Pin XLR Female Out 5 pin XLR Male In 10 position dip switch setting p Pint Accessories An external Adaptor Included Controls amp Functions D 1 Channel Switches Control the output of the DMX 512 signal respectively D Channel LEDs Indicate the corresponding channel switch s state ON or OFF Rear View RTO CE o oa i EEEH re ELN D Vey c 9VDC 4 D 6 4 Dip Switches Select the initial channel setting mode D DMX Output Socket Used to connect to DMX input socket of next unit B DMX Input Socket Used to connect
10. to get to channel 17 you would flip dip switches 1 amp 5 ON See below for more help Additional examples Dip Switch Setting DMX Address 1 2 3 4 5 6 7 8 9 ee 4 2 4 8 16 32 64 128 256 Dip Switch Setting DMX Address 1 2 3 4 5 6 7 8 9 AA ea 1 2 4 8 16 32 64 128 256 1 2 3 4 5 6 7 8 9 TE 1 2 4 8 16 32 64 128 256 1 2 3 4 5 6 7 8 9 ETRE o 1 2 3 4 5 6 7 8 9 AA 1 2 4 8 16 32 64 128 256 AA 1 2 4 8 16 32 64 128 256 1 2 3 4 5 6 7 8 9 ea 1 2 4 8 16 32 64 128 256 1 2 3 4 5 6 7 8 9 3 The DMX indicator will flash when DMX signal is present Switch Dimmer mode selection Dip switch 10 is the Mode selector switch When set to ON the pack will be in switch mode When set to OFF the pack is in linear dimming mode e In Switch mode the channel output will have a switch point at value 128 This means when relevant channel is below value 128 there will be no output for that channel When the value is at 128 or above the output will be ON at 100 for the relevant channel In Dimmer mode the intensity for each channel could be adjusted from 0 to 100 in real time Controls amp Functions Rear panel view Power input AC 120V 60Hz 15A Max 6 Power input Plug into an AC 120V 60Hz outlet 7 Power Switch This switch turns the
11. unit ON and OFF 8 DMX Input This 3 pin male XLR connector is the input and should be connected to a DMX controller or the previous DMX device in line 9 DMX Output This 3 pin female XLR connector is the output and should be connected to the next DMX device in line DMX Addressing on off About the DMX 16SW SYS Introduction Thank you for your purchasing of the Elation Professional DMX 16SW SYS To optimize the performance of this product please read these operating instructions carefully to familiarize yourself with the basic operation of this system The Elation Professional DMX 16SW SYS is simple to use All system components have been tested at the factory before being shipped to you Please simply connect cables between your DP 415 and DMX 16SW then you re ready to go Unpacking The DMX 16SW SYS has been thoroughly tested and shipped in perfect working condition Please take a few minutes to carefully inspect the system carton for damage that may have occurred during shipping If the carton appears to be damaged carefully inspect each system component for damage in the case that damage is found please contact our customer support center listed below for further instructions The Elation Professional DMX 16SW SYS carton should includes the following 1 DP 415 1 DMX 16SW 2 XLR DMX cable 1 External Adaptor 1 User s Manual Customer Support Every effort has been made to design dependable and reliable
Download Pdf Manuals
Related Search