FiberCom Media Converter User Manual V.1.01
Contents
1. 2 External Power Supply 2 Specifications Parameters Access mode Specifications 10 100 Mbps Gigabit Ethernet TEEE802 3 10BaseT Ethernet IEEE802 3U 100BaseTX FX Fast Standards Ethernet IEEE802 1Q VLAN IEEE802 1p CoS IEEE802 1D Spanning Tree MAC Bridges Wavelength 850nm 1310nm 1550nm Dual fiber multi mode 721 220m fiber size 62 5 125um 1804 550m fiber size 50 125um Dual fiber single mode 32 8k to 393 7k feet 10 20 40 60 80 100 120 Km Single fiber single mode 32 8k to 262 5k feet 10 20 40 60 80Km Category 5 twisted pairs 328 100m One RJ45 port Connected to STP UTP category 5 twisted pairs One fiber port dual fiber multi mode SC fiber size 50 62 5 125um Dual fiber single mode SC FC fiber port fiber size 9 125ym Single fiber single mode SC FC fiber port fiber size 9 125um Transmission distance Port Conversion mode Medium conversion Delay lt 10us Bit error rate lt 1 1000000000 MTBF 100 000 hours POWER power FX LINK fiber link action TP LINK100 LED twisted pair connection 100M TP ACT twisted pair packet forwarding action Power 90 265VAC Input using external power supply SVDC Input jack Power consumption SW Operating temperature 50 to 131 F 10 to 55 C Operating humidity 5 90 Storage temperature 40 to 158 F 40 to 70 C Storage humidity 5 90 non condensing Dimensions length 3 Connection Connect the FiberCom Media Conv2. 34 0870 FAX 516 338 4741 www electroind com Doc E201701 V 1 01 May 10 2010
3. FiberCom 10 100BaseT to 100BaseFX Bridging Media Converter User s Manual 1 Overview Electro Industries FiberCom 10 100BaseT to 100BaseFX Bridging Media Converter part EI FP 8110SA 25 provides 10 100Mbps communication between Cat 5 twisted pair Ethernet cables and Fiber Optic cables The FiberCom protects your copper wire investment while extending the range of your communication capability and preparing your network for future optimization FiberCom features include e Support for half duplex and full duplex transmission e Ability to extend range of communication from 1000 meters maximum with twisted pair alone to 80 kilometers Built in switching core to implement flow control and reduce broadcast packets Support for the transmission of extra long packets 1600 bytes over VLAN Built in 128kB RAM for data buffering Support for auto MDI MDIX function for seamless device connection Support for link pass through function LPF for fault detection Ability to interface with multiple types of Fiber ports i e dual fiber multi mode dual fiber single mode and single fiber single mode thereby meeting extended user requirements e Fiber optic immunity to electromagnetic interference EMI improves data transmission especially in environments with high EMI e g a manufacturing facility s plant floor IMPORTANT Inspect your FiberCom package to ensure it contains the following items 1 FiberCom Media Converter
4. erter as follows Connect the network device work station hub or switch with a G RJ45 interface to the RJ45 jack of the FiberCom through twisted pair Connect the multi single mode fiber to the SC ST Fiber interface of the FiberCom Plug the supplied Power supply into the FiberCom Once the devices are powered on the FiberCom LEDs indicate connection status See next section 4 Front Panel Indicators FP LINK Qi000 1 02 26mm H 2 75 70mm W 3 69 94mm L height width Power supply Input jack 3 6 Number LED Function Status Meaning 1 DUP UTP port duplex LED ON Full duplex OFF Half duplex 2 FP Fiber port link action status ON Fiber link is ACTIVE LINK LED OFF Fiber link is INACTIVE 3 PWR Power LED ON Power is ON OFF Power is OFF 4 RX UTP port link action status LED ON Data is being received Blink Data has been transmitted not currently transmitting OFF Data is not being sent out 5 100 UTP port speed LED ON 100M speed OFF 10M speed 6 TX UTP port link action status LED ON Fiber link is OK Blink Data is being received or transmitted OFF Fiber link has failed 5 Troubleshooting If the FiberCom Media Converter fails to operate follow these steps 1 Is the FiberCom s Power LED No illuminated See page 10 Is the power supply compatible with the AC outlet Is the power supply installed properly in the F
5. iberCom and the AC outlet Contact EIG s technical support Yes continue to step 2 2 Is the Duplex Link LED No check the copper cables to insure proper connection illuminated on a port with Yes twisted pair cable installed Amber light means the FiberCom has selected half duplex mode Green light means the FiberCom has selected full duplex mode If the mode is not correct disconnect and reconnect the twisted pair cable to restart the initialization process Continue to step 3 3 Is the LACT LED No illuminated on the on the fiber Check the fiber cables for proper cable port connection Verify that the TX and RX cables are connected to the FiberCom s RX and TX ports respectively Yes continue to step 4 4 Is the Speed LED No check the copper cables for proper connection illuminated on a port with Yes twisted pair cable installed Amber light means the FiberCom has selected 10Mbps operation Green light means the FiberCom has selected 100Mbps operation If the speed is not correct disconnect and reconnect the twisted pair cable to restart the initialization process FCC RFI Statement Federal Communications Commission FCC Radio Frequency Interference This device complies with part 15 of FCC regulations Electro Industries GaugeTech The Leader in Power Monitoring and Control 1800 Shames Drive Westbury NY 11590 Tel 516 3
Download Pdf Manuals
Related Search