Home

PL1 LED Luminaire (Discontinued) - Installation

1. PHILIPS Selecon PL1 LED Luminaires INSTALLATION amp USERS MANUAL Philips Selecon Offices Philips Selecon Dallas Philips Selecon Auckland 10911 Petal Street 19 21 Kawana Street Dallas TX 75238 Northcote Auckland 0627 Tel 1 214 647 7880 New Zealand Fax 1 214 647 8030 Tel 64 9 481 0100 Fax 64 9 481 0101 Philips Selecon New York Philips Selecon Europe 267 5th Ave 4th Floor Rondweg zuid 85 New York NY 10016 Winterswijk 7102 JD Tel 1 212 213 8219 The Netherlands Fax 1 212 532 2593 Tel 31 0 543 542516 Philips Selecon Asia Limited Unit C 14 F Roxy Industrial Centre No 41 49 Kwai Cheong Road Website Kwai Chung N T Hong Kong www seleconlight com Tel 852 2796 9786 Fax 852 2798 6545 The material in this manual is for information purposes only and is subject to change without notice Philips Selecon assumes no responsibility for any errors or omissions which may appear in this manual For comments and suggestions regarding corrections and or updates to this manual please visit the Philips Selecon web site at www seleconlight com or contact your nearest Philips Selecon office El contenido de este manual es solamente para informacion y esta sujeto a cambios sin previo aviso Philips Selecon no asume responsabilidad por errores o omisiones que puedan aparecer Cualquier comentario sugerencia o correcci n con respecto a este manual favor de dirijirlo a la oficina de Philips Selecon mas cerca
2. 51 Preset 17 Store DMX 52 53 Preset 18 Store DMX 54 55 Preset 19 Store DMX 56 57 Preset 20 Store DMX 58 59 Preset 21 Store DMX 60 61 Preset 22 Store DMX 62 63 Preset 23 Store DMX 64 65 Preset 24 Store DMX 66 67 Preset 25 Store DMX 68 69 Preset 26 Store DMX 70 71 Preset 27 Store DMX 72 73 Preset 28 Store DMX 74 75 Preset 29 Store DMX 76 77 Preset 30 Store DMX 78 79 Preset 31 Store DMX 80 81 Fixture Reset DMX 250 255 PHILIPS 24 DMX CONTROL Selecon PL1 LED Luminaires Installation amp User s Manual 2 8 Bit Mode Table 2 1 provides DMX channel mapping of all DMX512 control values when the PL1 LED Luminaire is in 8 bit DMX512 mode as set by the luminaire s menu system Table 2 1 PL1 LED Luminaire DMX Channel Mapping 8 Bit Mode Default DMX recommended SC Parameter Range DMX Range Description Channel E ang ange console default Serpro values 1 Intensity 0 255 0 100 0 8 bit control for Intensity of LED settings 2 Red 0 255 0 100 0 8 bit control of Red LEDs from 0 to full 3 Green 0 255 0 100 0 8 bit control of Green LEDs from 0 to full 4 Blue 0 255 0 100 0 8 bit control of Blue LEDs from 0 to full 5 White 0 255 0 100 0 8 bit control of White LEDs from 0 to full Used to access presets stored in fixture firmware such as CCT presets defined gel presets etc No Preset Activated
3. DMX 0 3 Color Preset 0 Off DMX 4 7 Color Preset 1 Scratch Pad DMX 8 11 Color Preset 2 Warm White DMX 12 15 Color Preset 3 Cool White DMX 16 19 Color Preset 4 Daylight DMX 20 23 Color Preset 5 Arc White DMX 24 27 Color Preset 6 Red DMX 28 31 Color Preset 7 Yellow DMX 32 35 Color Preset 8 Daylight Blue DMX 36 39 Color Preset 9 Magenta DMX 40 43 Color Preset 10 Aqua DMX 44 47 Color Preset 11 Medium Amber DMX 48 51 Color Preset 12 Lavender DMX 52 55 6 Preset Color Selection 0 255 0 100 0 Color Preset 13 Blue DMX 56 59 Color Preset 14 Light Pink DMX 60 63 Color Preset 15 Green DMX 64 67 Color Preset 16 Pink DMX 68 71 Color Preset 17 Amber White DMX 72 75 Color Preset 18 Dark Fuchsia DMX 76 79 Color Preset 19 Light Amber DMX 80 83 Color Preset 20 Steel Blue DMX 84 87 Color Preset 21 Lt Green Blue DMX 88 91 Color Preset 22 Orange DMX 92 95 Color Preset 23 Medium Pink DMX 96 99 Color Preset 24 Cyan DMX 100 103 Color Preset 25 Purple DMX 104 107 Color Preset 26 Custom DMX 108 111 Color Preset 27 Custom DMX 112 115 Color Preset 28 Custom DMX 116 119 Color Preset 29 Custom DMX 120 123 Color Preset 30 Custom DMX 124 127 Color Preset 31 Custom DMX 128 131 7 Not used for future use Allows for timing control of both the intensity and color
4. Selecon LCD Menu Operation 15 Installation amp User s Manual PL1 LED Luminaires 2 LCD Menu System The LCD Display Menu system consists of several categories Use the four arrow buttons as required refer to Figure 2 on page 15 to access and make changes to the menu items When the desired menu item is reached press OK to display the menu options Use navigation and OK buttons to view status and configure the LCD Menu as required Note Depending on the security settings certain menu items may be password protected You must have the set PassPIN in order to access these items Locked items will have a Key icon displayed next to them To navigate and access menu settings selections Step 1 At Main Menu press ESC MENU button once A small window will appear over Main Menu with sub menu categories Save as Preset Edit a Preset Color Mix Fan Control Settings Lock Fixture Enter Password h LED Status Step 2 Press OK at desired menu item to access and make changes Q D Oo Oo Step 3 Make changes as desired Note For complete menu structure and available options see Menu Structure continued on page 18 Note When DMX512 signal is present Edit Preset and Color Mix options will not appear in menu structure To navigate fixture status menus Step 1 At Main Menu press LEFT or RIGHT arrow button once Main menu screen will change to fixture status screen will ap
5. 3 6 19 3 8 8 20 4 21 4 2 22 4 4 9 23 4 6 24 4 8 10 25 5 26 5 2 27 5 4 11 28 5 6 29 5 8 30 6 12 31 6 2 32 6 4 13 33 6 6 34 6 8 35 7 0 14 36 7 2 37 7 4 15 38 7 6 39 7 8 40 8 16 41 8 2 42 8 4 17 43 8 6 44 8 8 45 9 18 46 9 2 47 9 4 19 48 9 6 49 9 8 50 10 20 51 10 2 PHILIPS Ee Selecon PL1 Luminaire DMX Timing Channel Detail 29 Installation amp User s Manual PL1 LED Luminaires 30 DMX CONTROL Value DMX Seconds 52 10 4 53 10 6 21 54 10 8 55 11 22 56 11 2 57 114 58 11 6 23 59 11 8 60 12 24 61 12 2 62 124 63 12 6 25 64 12 8 65 13 26 66 13 2 67 134 68 13 6 27 69 13 8 70 14 28 71 14 2 72 14 4 73 14 6 29 74 14 8 75 15 30 76 15 2 77 15 4 78 15 6 31 79 15 8 80 16 81 16 2 32 82 16 4 83 16 6 33 84 16 8 85 17 86 17 2 34 87 17 4 88 17 6 35 89 17 8 90 18 91 18 2 36 92 18 4 93 18 6 37 94 18 8 95 19 96 19 2 38 97 19 4 98 19 6 39 99 19 8 100 20 101 21 40 102 22 103 23 104 24 41 105 25 PHILIPS Selecon PL1 LED Luminaires Installation amp User s Manual Value DMX Seconds 106 26 42 107 27 108 28 109 29 43 110 30 111 31 44 112 32 113 33 114 34 45 115 35 116 36 46 117 37 118 38 119 39 47 120 40 121 41 48 122 42 123 43 124 44 49 125 45 126 46 127 47 50 128 48 129 49
6. 51 130 50 131 51 132 52 52 133 53 134 54 53 135 55 136 56 137 57 54 138 58 139 59 55 140 60 141 61 142 62 56 143 63 144 64 57 145 65 146 66 147 67 58 148 68 149 69 59 150 70 151 71 152 72 60 153 73 154 74 155 75 61 156 76 157 77 62 158 78 159 79 PHILIPS SE Selecon PL1 Luminaire DMX Timing Channel Detail 31 Installation amp User s Manual PL1 LED Luminaires 32 DMX CONTROL Value DMX Seconds 160 80 63 161 81 162 82 64 163 83 164 84 165 85 65 166 86 167 87 66 168 88 169 89 170 90 67 171 91 172 92 68 173 93 174 94 175 95 69 176 96 177 97 178 98 70 179 99 180 100 71 181 101 182 102 183 103 72 184 104 185 105 73 186 106 187 107 188 108 74 189 109 190 110 75 191 111 192 112 193 113 76 194 114 195 115 77 196 116 197 117 198 118 78 199 119 200 120 79 201 121 202 122 203 123 80 204 124 205 125 81 206 126 207 127 208 128 82 209 129 210 130 211 131 83 212 132 213 133 PHILIPS Selecon PL1 LED Luminaires Installation amp User s Manual Value DMX Seconds 84 214 134 215 135 216 136 85 217 137 218 138 86 219 139 220 140 221 141 87 222 142 223 143 88 224 144 225 145 226 146 89 227 147 228 148 229 149 90 230 150 231 151 91 232 152 233 153 234 154 92 235 155 236 156 93
7. Cable XLR 5 Female to RJ 45 12 inches 305 mm Black PL1DMXMRJ47 PL1 LED Luminaire DMX512 Cable XLR 5 Male to RJ 45 12 inches 305 mm White PL1DMXMRJ48 PL1 LED Luminaire DMX512 Cable XLR 5 Male to RJ 45 12 inches 305 mm Black PL1 LED Luminaire PL1 LED Luminaire Wireless DMX Receivers Part Number Description PL1WDMX01 PL1 LED Luminaire W DMX Wireless DMX512 Receiver White PL1WDMX03 PL1 LED Luminaire W DMX Wireless DMX512 Receiver Black PL1LDMX01 PL1 LED Luminaire Lumen Radio Wireless DMX512 Receiver White PL1LDMX03 PL1 LED Luminaire Lumen Radio Wireless DMX512 Receiver Black PL1SDMX01 PL1 LED Luminaire City Theatrical Wireless DMX512 Receiver White PL1SDMX03 PL1 LED Luminaire City Theatrical Wireless DMX512 Receiver Black PL1 LED Luminaire PL1 LED Luminaire Wireless DMX Transmitters Part Number Description PL1WDMXTR PL1 LED Luminaire W DMX Wireless DMX512 Transmitter PL1LDMXTR PL1 LED Luminaire Lumen Radio Wireless DMX512 Transmitter PL1SDMXTR PL1 LED Luminaire City Theatrical Wireless DMX512 Transmitter PL1 LED Luminaire Tools Part Number Description ARLAKTOOL Allen Wrench Hand Tool with 2 5 mm 3 0 mm 4 mm and 5 mm Hey Keys PL1 LED Luminaire Connectors North American Market Part Number Description GR 15A NEMA 5 15P Male Edison Connector GP 20A Male Stage Pin Connector GTL 20A NEMA L5 20P Male Twist Lock Connector PHILIPS Selecon ACCESSORIES Installation amp User s Manual PL1 LED Luminaires
8. DIRECTLY INTO BEAM WARNING THIS DEVICE IS A CLASS 2 LASER DO NOT STARE OR LOOK Figure 3 PLIIRR Programming Remote 34 INFRARED REMOTE CONTROL PHILIPS Selecon PL1 LED Luminaires Installation amp User s Manual To select and program PL1 LED luminaire with PL1IIRR remote Note The IR on the PL1 LED luminaire must be set to Enabled in order for the PLIIRR remote to communicate and control the fixture Refer to PL1 LED Luminaire Installation amp User s Manual on luminaire menu settings Step 1 Point PLIIRR programming remote Laser IR window directly at luminaire IR programming window as shown in Figure 4 and hit Enter button Note each luminaire to be programmed adjusted needs to be selected and programmed adjusted individually PL1 LED Luminaire IR enabled model PL1 IR Port reem ENER S KAO de on Be H d PL1IRR Remote Control Figure 4 PL1 LED Luminaire Programming Control Step 2 Point PLIIRR remote directly at luminaire IR window and hit Laser button Luminaire to be programmed or adjusted is now selected Note At luminaire IR port a Blue LED will illuminate when the fixture is in programming mode and blink Red when buttons are pressed on IR remote to confirm it sees the remote and is receiving commands Step 3 Set luminaire to preset or make adjustments as desired Step 4 To save setti
9. Luminaires TABLE OF CONTENTS Philips Selecon Offices annee ege Inside Front Cover IMPORTANT INFORMATION Warnings and N tices 52 tannins 1 Additional Resources for DMXAI nee 1 Philips Selecon Limited Three Year Warranty ss 1 TABLE OF CONTENTS PREFACE PATO UE LMS leren EES 4 Product D scriphons is sneneeneminietninsenin errant none a en 4 PL1 LED Luminaire Spot with Local DMX512 IR Control North American Market 4 PL1 LED Luminaire Spot with Local DMX512 IR Control International Markets 4 ACCESSORIES seg gege gege EENS AER 5 PL1 LED Luminaire IR Remote 5 PL1 LED Luminaire Barndoors amp Filter Holders 5 PL1 LED Luminaire DMX512 Cables ses 5 PL1 LED Luminaire PL1 LED Luminaire Wireless DMX Receivers 5 PL1 LED Luminaire PL1 LED Luminaire Wireless DMX Transmitters ccccesceescesseeseeeeeeeeeeeeeeeeeeeseenees 5 PILL LED Luminaire Ke EE 5 PL1 LED Luminaire Connectors North American Market ss 5 PL1 LED LUMINAIRE OVERVIEW PL LED Luminaire e 6 Luminaire Components esst R a EE E EEE REE EEEE AAEE EEEE EE ERE 6 LCD Display Menu EE 6 INSTALLATION AND SET UP Power Reguire ment Ser E E EE 7 Connecting POW EE T Connecting to the DMX512 Network 7 eru ue 8 Track Mounted Models PLIRCO1 TLOLO1 and PLIRCOLTLOLO 9 Track Mounted Models PLIRCO1 TLSI01 and PLIRCO1 TLSIO3 0 cc ececcecssecseeseeseeseeseseeeecnseeeeeenes 10 Track Mounted Mode
10. Pad DMX 8 11 Color Preset 2 Warm White DMX 12 15 Color Preset 3 Cool White DMX 16 19 Color Preset 4 Daylight DMX 20 23 Color Preset 5 Arc White DMX 24 27 Color Preset 6 Red DMX 28 31 Color Preset 7 Yellow DMX 32 35 Color Preset 8 Daylight Blue DMX 36 39 Color Preset 9 Magenta DMX 40 43 Color Preset 10 Aqua DMX 44 47 Color Preset 11 Medium Amber DMX 48 51 Color Preset 12 Lavender DMX 52 55 Color Preset 13 Blue DMX 56 59 Color Preset 14 Light Pink DMX 60 63 Color Preset 15 Green DMX 64 67 Color Preset 16 Pink DMX 68 71 Color Preset 17 Amber White DMX 72 75 Color Preset 18 Dark Fuchsia DMX 76 79 Color Preset 19 Light Amber DMX 80 83 Color Preset 20 Steel Blue DMX 84 87 Color Preset 21 Lt Green Blue DMX 88 91 Color Preset 22 Orange DMX 92 95 Color Preset 23 Medium Pink DMX 96 99 Color Preset 24 Cyan DMX 100 103 Color Preset 25 Purple DMX 104 107 Color Preset 26 Custom DMX 108 111 Color Preset 27 Custom DMX 112 115 Color Preset 28 Custom DMX 116 119 Color Preset 29 Custom DMX 120 123 Color Preset 30 Custom DMX 124 127 Color Preset 31 Custom DMX 128 131 11 Preset Color Selection 0 255 0 100 0 12 Not used for future use PHILIPS Selecon 16 Bit Mode 23 Installation amp User s Manual PL1 LED Luminaires Table 3
11. circuit selector knob to corresponding selection Step 5 To remove track adapter from track a Select 0 Off position of circuit selector knob b Turning mechanical retaining know counterclockwise c Pull adapter out of track by the mechanical retaining knob end first Polarity Groove Rotation Lock Screw Do Not Over Tighten _ Mechanical Retaining Knob Circuit Selector PHILIPS a Selecon Mounting 11 Installation amp User s Manual PL1 LED Luminaires To attached adapter to Global three circuit track Note Use intended for the connection of spotlights to the GLOBAL pro former NOKIA XTS 3 circuit tracks The MULTI adapter XTSA 68 suits almost every 3 circuit track on the market Step 1 Push MULTI adapter into track Step 2 Turn mechanical retaining knob clockwise Step 3 Select desired circuit with circuit selector knob Step 4 To remove MULTI adapter from track turn circuit selector to OFF position Step 5 Turn mechanical retaining knob counterclockwise Step 6 Pull and remove from track a PHILIPS 12 INSTALLATION AND SET UP Selecon PL1 LED Luminaires Installation amp User s Manual PL1 LED Luminaire Ceiling Rose Mount Models Note These models are not offered in the North American market International Detail of power connection block in ceiling mounted models For wire codes see Connecting Power on page 7 with Ceil
12. of security this allows 1 PassPIN 4 Digits 0 to 9 ery you to change the level while in the 39 Settings Screen 3 Level 1 PIN 4 Digits 0 to 9 1111 Sets Level 1 PassPIN 3 Level 2 PIN 4 Digits 0 to 9 2222 Sets Level 2 PassPIN 3 Level 3 PIN 4 Digits 0 to 9 3333 Sets Level 3 PassPIN Security Level after Power Up if not 3 Power Up 1 3 or Locked 3 Locked Level 0 Settings 21 Installation amp User s Manual PL1 LED Luminaires 22 General 4 5 30W 40W 50W 70W Sets the maximum power setting of the 1 Power Emit 90W 100W 120W TZON LED engine When the Fixture Powers Up what does it ee Se output Scratch Pad is an automatically 1 Power U White Da Li ht Cool White saved Preset Last Set is the last thing R Preset30 St coming out of the fixture this could be Last Set Warm White with the intensity changed from that of the Preset 3 IR Enabled No Yes Yes Turns IR Laser detection On Off 3 Reset Hours No Yes No Resets luminaire s operational hours Presets Determines if the factory Calibrated 3 Protected No 5 25 Yes Presets Color Mix is protected from changes Reload Factory Calibrated Presets 3 Load Factory NoYes de Intensity changes will also be reloaded DMX Enables or disabled DMX communication No Yes or Wireless if through the luminaires DMX512 ports 3 DMX Enabled ce uipped Yes Sets the DMX feature to Wireless DMX if quipp wire
13. parameters Channel should default to 255 Af for smoothest actions using console and or z 0 S Timing ess 15100 ES manual fades Refer to PL1 Luminaire DMX Timing Channel Detail on page 28 for more information PHILIPS ee Ss Selecon 8 Bit Mode 25 Installation amp User s Manual PL1 LED Luminaires Table 2 1 PL1 LED Luminaire DMX Channel Mapping 8 Bit Mode Used to set different modes parameters and functions of the luminaire Set control channel value for desired action Hold value for at least 3 seconds Set control channel value to 0 without any scaling Default Setting on Console DMX 0 Display On Off DMX 3 4 Reset All to Defaults DMX 5 7 Quiet Mode DMX 11 13 Normal Mode DMX 14 15 Preset 1 Store DMX 20 21 Preset 2 Store Intensity Only DMX 22 23 Preset 3 Store Intensity Only DMX 24 25 Preset 4 Store Intensity Only DMX 26 27 Preset 5 Store DMX 28 29 Preset 6 Store DMX 30 31 Preset 7 Store DMX 32 33 Preset 8 Store DMX 34 35 Preset 9 Store DMX 36 37 Preset 10 Store DMX 38 39 Preset 11 Store DMX 40 41 Preset 12 Store DMX 42 43 Preset 13 Store DMX 44 45 Preset 14 Store DMX 46 47 Preset 15 Store DMX 48 49 Preset 16 Store DMX 50 51 Preset 17 Store DMX 52 53 Preset 18 Store DMX 54 55 Preset 19 Store DMX 56 57 Preset 20 Store DMX 58 59 Preset 21 Store DMX 60 61 Preset
14. 22 Store DMX 62 63 Preset 23 Store DMX 64 65 Preset 24 Store DMX 66 67 Preset 25 Store DMX 68 69 Preset 26 Store DMX 70 71 Preset 27 Store DMX 72 73 Preset 28 Store DMX 74 75 Preset 29 Store DMX 76 77 Preset 30 Store DMX 78 79 Preset 31 Store DMX 80 81 Fixture Reset DMX 250 255 9 Control 0 255 0 100 0 PHILIPS 26 DMX CONTROL Selecon PL1 LED Luminaires Installation amp User s Manual 3 DMX 3 Channel 3 Chan Mode Table 2 2 provides DMX channel mapping of all DMX512 control values when the PL1 LED Luminaire is in 3 Channel 3 Chan DMX512 mode as set by the luminaire s menu system Table 2 2 PL1 LED Luminaire DMX Channel Mapping 3 Chan Mode Default DMX o recommended n Channel Parameter Range DMX Range consol default Description values 1 Intensity 0 255 0 100 0 8 bit control for Intensity of LED settings Used to access presets stored in fixture firmware such as CCT presets defined gel presets and more No Preset Activated DMX 0 3 Color Preset 0 Off DMX 4 7 Color Preset 1 Scratch Pad DMX 8 11 Color Preset 2 Warm White DMX 12 15 Preset Color Selection Color Preset 3 Cool White DMX 16 19 Color Preset 4 Daylight DMX 20 23 Notes Color Preset 5 Arc White DMX 24 27 Color Preset 6 Red DMX 28 31 Color Presets 5 Color Preset 7 Yellow DMX 32
15. 237 157 238 158 239 159 94 240 160 241 161 95 242 162 243 163 244 164 96 245 165 246 166 97 247 167 248 168 249 169 98 250 60mS 251 80mS 99 252 100mS 253 120mS 254 140mS 100 an 160mS Note DMX values 250 to 255 provide smoothing when using console fade timing DMX value 255 recommended default will provide the smoothest timing PHILIPS a Selecon PL1 Luminaire DMX Timing Channel Detail 33 Installation amp User s Manual PL1 LED Luminaires INFRARED REMOTE CONTROL 1 Infrared Remote Control Overview The PLIIRR infrared preset programming remote sold separately allows users convenient access to adjust and program luminaire parameters presets 1 through 6 and Off intensity preset color temperatures or full color mixing from the floor Before using the remote please familiarize yourself with all available controls shown in Figure 3 Infrared Remote Control Features Program Enter After the luminaire to be programmed is selected by Laser press Enter to set the luminaire to programming mode 7 Laser Luminaire Selector Press D TE Laser to select individual luminaire for Si ez EXIT programming adjustment CANCEL a Exit Press to exit programming mode RES INTENSITY Cancel Cancels the learn features any programming made will not be recorded RGBW will not be changed HA
16. 35 through 25 are cali Color Preset 8 Daylight Blue DMX 36 39 brated factory col Color Preset 9 Magenta DMX 40 43 ors and can be Color Preset 10 Kelly Green DMX 44 47 reloaded if needed Color Preset 11 Medium Amber DMX 48 51 through the fixture s Color Preset 12 Lavender DMX 52 55 menu system o Color Preset 13 Blue DMX 56 59 2 a These colors have 05 259 0 100 2 Color Preset 14 Light Pink DMX 60 63 been matched to Color Preset 15 Green DMX 64 67 precise X and Y Color Preset 16 Pink DMX 68 71 coordinates at the Color Preset 17 Amber White DMX 72 75 center of the beam Color Preset 18 Dark Fuchsia DMX 76 79 at wide angle we Color Preset 19 Light Amber DMX 80 83 have given you the Color Preset 20 Steel Blue DMX 84 87 ability to adjust Color Preset 21 Lt Green Blue DMX 88 91 these colors as Color Preset 22 Orange DMX 92 95 your personal per Color Preset 23 Medium Pink DMX 96 99 ception may vary Color Preset 24 Cyan DMX 100 103 Color Preset 25 Purple DMX 104 107 Color Preset 26 Custom DMX 108 111 Color Preset 27 Custom DMX 112 115 Color Preset 28 Custom DMX 116 119 Color Preset 29 Custom DMX 120 123 Color Preset 30 Custom DMX 124 127 Color Preset 31 Custom DMX 128 131 Allows for timing control of both the intensity and color parameters Channel should default to 255 sc for smoothest actions using con
17. CONTROL on page 23 See DMX512 DMX512 Cable Options Below from console or DMXS512 out from first DMXS5 12 out to the next luminaire or ER to second luminaire DMXS12 controlled device p PL1 LED Luminaires DMXS12 Cable Options DMX512 Connections PL1 LED Luminaire DMX Cables DMX to RJ45 DMX512 Signal XLRPin RJ45Pin Sold Separately Common Drain 7 DMX512 DMX512 3 EPI To Luminaire RJ45 DMX512 XLR Male Note Remaining pins on each connector are not used Note For cables required to operate and control PL1 LED Luminaires via DMX512 see PL1 LED Luminaire DMX512 Cables on page 5 Cell EL TI To Luminaire RJ45 DMX512 XLR Female Mounting There are several ways to mount PL1 LED Luminaires depending on mounting option purchased Below are the various mounting options from Philips Selecon Refer to Product Descriptions on page 4 for additional information WARNING Before attempting any installation or service disconnect all power at power source Turning off the luminaire does not disconnect power Installation and service should only be performed by a trained and qualified professional Be sure to check circuit capacity before installing luminaires Refer to IMPORTANT INFORMATION on page 1 for more information Note For track mounted luminaires refer to the track manufactu
18. CUIT 2 FINGER LOCATION FOR REMOVAL CLAMPING TABS TS PHILIPS Selecon Mounting 9 Installation amp User s Manual PL1 LED Luminaires Track Mounted Models PL1RC01 TLSIO1 and PL1RC01 TLSIO3 To attached adapter to LSI two circuit track Step 1 To insert into track turn switch OFF and open Handle Insert Adapter straight up into the track until it seats evenly close Handle turn switch ON Track Locking Handle Open Power Switch Off Position Step 2 Ifusing one circuit track make sure that the Brass Contacts which protrude from the side of the Adapter are inserted facing the copper bus bars inside the track Step 3 Jfusing two circuit track inserting the Adapter in one direction will connect to Circuit ONE Removing and reversing the direction of the Adapter will connect to Circuit TWO Track Locking Handle Closed Power Switch On Position Step 4 To remove the Adapter turn switch OFF open handle and pull straight away from track PHILIPS Selecon 10 INSTALLATION AND SET UP PL1 LED Luminaires Installation amp User s Manual Track Mounted Models PL1RC01 TGO1 and PL1RC01 TGO3 To attached adapter to Global two circuit track Step 1 Insert track adapter with polarity groove towards polarity ridge of track Step 2 Push track adapter into track until it snaps into place Step 3 Turn mechanical retaining knob clockwise Step 4 Select desired circuit by turning
19. G 1 LCD Menu Operation The PL1 LED Luminaire s LCD Display and Menu System provides local control for accessing all the fixture s status information menu options and settings Note If there are multiple luminaires in a system changes would need to be made at each LCD Menu as desired Upon power up the LCD will display the main screen showing the product type name If DMX is enabled the programmed address will appear after power up Escape Button Enters menu options Navigates backs up one menu level PHILIPS Selecon LCD Display gt Displays all menu parameters and P L 1 option settings Also displays DMX512 address DMX models only PHILIPS ENTERTAINMENT V 0 01 INTENSITY Button Allows the customization of current intensity light output Note using y y the LEFT and RIGHT arrow buttons E Spee you can select each RGBW gt ESC channel individually and change r F PRESE INTENSITY MENU their intensity using the UP and DOWN arrows PRESET Button gt lt 4 Allows the recall of stored presets a zk Up Down Left Right Arrow Buttons __ Navigates menu system and used for selecting and setting options OK Enter Button 7 Accesses details activates a field or enters a setting depending on the current menu item Figure 2 LCD Display and Menu System PHILIPS
20. H RED GREEN BLUE WHITE Learn After adjustments are made the Learn button in conjunction with a preset button stores the new settings to a specific preset if desired PHILIPS Selecon DAY a Preset White Color Temperature Allows selection of Warm Cool or Day C color temperatures Note only intensities may be stored EDURRE on White Color Temperature presets These presets cannot be edited or changed Laser IR Window Laser and IR programming emits from this end PL1IRR LED indicator The LED indicator will flash each time a button is pressed Intensity Raise Lower Press top button to raise intensity and bottom button to lower it Tap the up for 2 increase or tap down for a 1 decrease Press and hold top or bottom button for sequential raise lower Individual LED Color Adjustment Allows the raising or lowering of individual LED colors Press top button to change color and bottom button to lower it Tap the up for 2 increase or tap down for a 1 decrease Press and hold top or bottom button for sequential raise lower Presets 6 Levels or Off Allows selection and programming of one of six Presets 1 through 6 or Preset Off Notes Preset Off cannot be edited or changed e Presets 1 through 6 on remote con trol equate to Presets 5 through 10 on PL1 LED luminaire display
21. Luminaire provides two timing channels in 16 bit mode one for intensity time and one for color time and one timing channel in 8 bit color and intensity timing combined The luminaire uses its timing channel value to calculate a smooth continuous operation for a given time and transition Guidelines e Timing channels support time values from zero to 169 seconds e To use a timing channel instead of console timing it is recommended to set the timing channel to the desired value and set cue and or console cue fade time to zero A combination of time controls can produce unexpected results e The default value setting in the profile should be 255 proportional control to allow smooth operation when using console timing e The timing channel data should change as a snap A zero value will give the fastest operation however without any smoothing this can appear steppy in console timed moves Refer to PL1 Luminaire Timing Channel Detail on page 29 for more information PHILIPS SR OOOO Selecon PL1 LED Luminaires Installation amp User s Manual Table 3 PL1 Luminaire Timing Channel Detail Value DMX Seconds 0 0 Full Speed 1 0 2 2 0 4 1 3 0 6 4 0 8 2 5 1 6 1 2 7 1 4 3 8 1 6 9 1 8 4 10 2 11 2 2 12 2 4 5 13 2 6 14 2 8 6 15 3 16 3 2 17 3 4 7 18
22. PL1 LED LUMINAIRE OVERVIEW 1 PL1 LED Luminaire Components Luminaire Components O 1 LCD Display Menu see LCD Display Menu on page 6 for more information 2 Tilt Axis Point see detail 3 Lens Barrel 4 Locking Focus Zoom Knob 5 Mounting Point 6 DMX512 In Out Connections both ports are In Out see detail 7 Diffuser Accessory Holder 8 IR Programming window 9 Allen Wrench Tool part number ARLAKTOOL included with luminaire contains 2 5mm 3mm 4mm amp 5mm Allen hex keys for locking pan or tilt DMX512 In Out Connections IT Note Some components not __ shown for clarity LCD Display Menu Se 1 LCD Display Menu System 2 Preset Intensity Menu Access Buttons Ola 3 Function Menu System Select Push Buttons 2 gt ESC PRESET INTENSITY MENU A Note For Menu operation and GJ EM o e programming details refer to LCD Menu Operation on page 15 A4 PHILIPS 6 PL1 LED LUMINAIRE OVERVIEW Selecon PL1 LED Luminaires Installation amp User s Manual INSTALLATION AND SET UP 1 Power Requirements The PL1 LED Luminaire operates on 120 to 240 volts AC 10 auto ranging The luminaire contains an auto ranging power supply Depending on supply voltage each luminaire can draw up to 1 91 amp
23. PL1 LED Luminaire Spot Ceiling Rose White PL1RC03 PL1 LED Luminaire Spot Ceiling Rose Black PL1RHC01 PL1 LED Luminaire Spot fitted with Half Coupler 1 meter AC Input Cable White PL1RHCO3 PL1 LED Luminaire Spot fitted with Half Coupler 1 meter AC Input Cable Black PLIRCTRO1 PL1 LED Touring Rental Spot Luminaire with a Lock Off Handle and C Clamp 1 meter AC Input Cable White PLIRCTRO3 EE be E Rental Spot Luminaire with a Lock Off Handle and C Clamp 1 meter AC Input PHILIPS Selecon PL1 LED Luminaires Installation amp User s Manual ACCESSORIES Contact your Authorized Philips Selecon Dealer for price and availability of all accessories for PL1 LED Luminaires 3 Additional information can be found on the Philips Selecon web site at www seleconlight com PL1 LED Luminaire IR Remote Part Number Description PL1IRR PL1 LED Luminaire Handheld IR Preset Programmer PL1 LED Luminaire Barndoors amp Filter Holders Part Number Description PL1CF PL1 LED Luminaire Color Filter Holder PL1BD0103 PL1 LED Luminaire Barndoor White Exterior Black Interior PL1BD03 PL1 LED Luminaire Barndoor Black Exterior Black Interior PL1 LED Luminaire DMX512 Cables Part Number Description PL1DMXFRJ45 PL1 LED Luminaire DMX512 Cable XLR 5 Female to RJ 45 12 inches 305 mm White PL1DMXFRJ46 PL1 LED Luminaire DMX512
24. PL1 LED Luminaire DMX Channel Mapping 16 Bit Mode Allows for luminaire timing of intensity Profile should default to DMX 255 for smoothest 13 Intensity Time 0 255 0 100 255 console fade times Refer to PL1 Luminaire DMX Timing Channel Detail on page 28 for more information on timing values Allows for luminaire timing of LEDs Profile should default to DMX 255 for smoothest 14 Color Time 0 255 0 100 255 console fade times Refer to PL1 Luminaire DMX Timing Channel Detail on page 28 for more information on timing values Used to set different modes parameters and functions of the luminaire Set control channel value for desired action Hold value for at least 3 seconds Set control channel value to 0 without any scaling Default Setting on Console DMX 0 Display On Off DMX 3 4 Reset All to Defaults DMX 5 7 Quiet Mode DMX 11 13 Normal Mode DMX 14 15 Preset 1 Store DMX 20 21 Preset 2 Store Intensity Only DMX 22 23 Preset 3 Store Intensity Only DMX 24 25 Preset 4 Store Intensity Only DMX 26 27 Preset 5 Store DMX 28 29 Preset 6 Store DMX 30 31 Preset 7 Store DMX 32 33 Preset 8 Store DMX 34 35 Preset 9 Store DMX 36 37 Preset 10 Store DMX 38 39 15 Control 0 255 0 100 0 Preset 11 Store DMX 40 41 Preset 12 Store DMX 42 43 Preset 13 Store DMX 44 45 Preset 14 Store DMX 46 47 Preset 15 Store DMX 48 49 Preset 16 Store DMX 50
25. PS Selecon Menu Structure continued Continued from previous page Settings Sub Menu Options Comments SETTINGS Option Scrolls and sets the various fixture See Settings on page 21 for details settings using arrow buttons Lock Fixture Sub Menu Options Comments Use arrow buttons to make selection Press OK to accept Note a 8 e password must be established set in LOCK Are you sure Yes to Lock Fixture No order to lock a fixture Locking the fixture will disable access to changing menu settings Enter Password Sub Menu Options Comments Enter Pass PIN Enter four digit password For details refer 10 Saeed an page 19 LED Status Sub Menu Options Comments Displays LED s current status in LED Status Information percentage of Intensity Red Green Blue and White elements of Scrolls through the various levels LED 1 the LED Also displays current color using arrow buttons as indicated on temperature i e WARM WHITE menu screen Depending on the Fan Speed operational LED junction arrow button pressed the screens temperature power settings may appear ina different order that Displays DMX levels for each LED shown in Options Levels element Red Green Blue and White and total power Security Unwanted changes to the Fixture s Configuration or Setting can be controlled by setting
26. Turn off luminaire and allow to cool completely Step 2 Place luminaire on a flat clean surface Be careful not to scratch or damage luminaire Note A long 3 mm Allen hex key is required to perform this procedure PHILIPS w tee Selecon PL1 LED Luminaires Installation amp User s Manual Step 3 Before opening luminaire head cover note position of lens focus zoom knob position to reset focus zoom position after completion of procedure Step 4 At luminaire head cover as shown in Figure 5 using 3 mm Allen hex key completely loosen three captive screws securing cover Captive Screws Luminaire Head Cover Figure 5 PL1 LED Luminaire Head Cover Step 5 Swing open luminaire head cover Step 6 As illustrated in Figure 6 unscrew locking focus zoom knob by hand and remove Be sure not to lose washer or spring that resides inside of knob Step 7 Noting orientation of lens tube remove lens tube assembly from luminaire head Step 8 Clean interior side of front lens by applying a small amount of reagent grade isopropyl alcohol to lint free lens tissue Step 9 Wipe all debris dirt fingerprints etc from lens Step 10 Using a second lint free lens tissue wipe off any alcohol residue Step 11 Clean Aspheric LED Lens as described in Steps 8 through 10 Captive Screws LED Cooling Assembly Luminaire Head Cover Aspheric LED Lens Lens Tube Assembly Le Plastic Washer Focus Zoom Kno
27. a security level or Locking the Fixture Three levels of security are available in addition to completely Locking the Fixture PL1 luminaires are shipped with default passwords Users may set their own password four digit number When setting a password write it down and keep it in a secure location Note Philips Selecon does not have records of passwords established by users or owners Note Contact Philips Selecon technical support if a unit is locked and the password is lost for instructions on how to reset luminaire Note If the Fixture is locked when it is powered down the fixture will remain in the locked state when powered up Passwords Establishing or Changing Passwords Step 1 Ata Status Screen press MENU and scroll to Settings press OK Step 2 Go to the Security section Security 19 Installation amp User s Manual PL1 LED Luminaires Step 3 Select a Level to change Level 1 PIN Level 2 PIN Level 3 PIN Step 4 Press OK to edit using the UP ARROW DOWN ARROW LEFT ARROW or RIGHT ARROW keys to enter a four digit password using 0 to 9 Step 5 Press OK to save changes If you hit ESC Escape password will not be stored and process must be repeated Step 6 Password is set Note The current security level is displayed next to the Security heading Only Passwords at or below that level will be displayed for modification The level can be changed by entering a higher le
28. available to edit the name of a preset via Screen button However the names of Presets 0 4 cannot be edited Use the LEFT ARROW and RIGHT ARROW keys to select the character to be changed and use the UP ARROW and DOWN ARROW keys to change that character The Character Scroll order is A Z space 0 9 If you are scrolling up the Alpha character displays as Upper Case if you are scrolling down the Alpha character displays as Lower Case Stop on the character you want ignoring case then press the opposite UP ARROW or DOWN ARROW key if you want to change the case OK to save changes ESC to cancel changes Settings The following Parameters can be changed on the Settings Screen The first column Security Level is the minimum security level you have to be at before the line is displayed for editing in the Settings screen To edit a value on the Setting Screen use the UP ARROW or DOWN ARROW keys to move the highlight to the settings value you wish to change Press OK to begin editing that value Use the UP ARROW DOWN ARROW LEFT ARROW or RIGHT ARROW keys to make changes to the value Press OK when complete to save changes or ESC to cancel changes to that value When done making changes on the Settings Screen press ESC to re boot fixture and implement changes Fixture will not re boot if nothing was changed Security Level Parameter Values Default Description Security Enter There are 4 levels
29. b Figure 6 PL1 LED Luminaire Lens Tube Assembly Note Remove any dust or debris that may be present in rear of luminaire head next to LED Cooling Assembly If A required use moisture and oil free compressed air duster DO NOT blow compressed air directly into fan or debris may become lodged in LED cooling unit fins Step 12 Reinstall lens tube by perform Steps 3 to 6 in reverse order 3 Service and Maintenance For all other service and maintenance issues please contact your local Philips Selecon office or an Authorized Service Center PHILIPS Selecon Service and Maintenance 37 Installation amp User s Manual PL1 LED Luminaires WARNING Disassembly other than as described herein alterations unauthorized service etc will void the product warranty Contact your local Philips Selecon office or an Authorized Service Center for technical support and service 4 Accessories Only Philips Selecon approved accessories should be used with your PL1 LED Luminaire For a list of available accessories from Philips Selecon please see ACCESSORIES on page 5 For questions regarding accessories please contact your local Authorized Philips Selecon Dealer or Philips Selecon office To install diffuser or barndoor on a PL1 LED luminaire Step 1 Lower intensity of PL1 luminaire to no output WARNING Using a prying device such as a screwdriver can damage locking mechanism It is designed to be A unlatch
30. conlight com for more details 2 PL1 LED Luminaire Dimensions 4 6 in 116 0 mm 1 2 in 30 0mm D 44in 112 0 mm 2 6 in 46in 63in 116 0 mm 160 0 mm 54 in 137 5 mm i 5 7in TILT AXIS dado m 6 8 in 9 9 in 172 7 mm 251 5 mm 207 2 mm 40 TECHNICAL SPECIFICATIONS CE PHILIPS Selecon PL1 LED Luminaires Installation amp User s Manual Notes PHILIPS EE Selecon PL1 LED Luminaire Dimensions 41 PHILIPS Selecon Philips Selecon Dallas 10911 Petal Street Dallas TX 75238 Tel 1 214 647 7880 Fax 1 214 647 8031 Philips Selecon New York 267 5th Ave 4th Floor New York NY 10016 Tel 1 212 213 8219 Fax 1 212 532 2593 Philips Selecon Hong Kong Unit C 14 F Roxy Industrial Centre No 41 49 Kwai Cheong Road Kwai Chung N T Hong Kong Tel 852 2796 9786 Fax 852 2798 6545 Philips Selecon Auckland 19 21 Kawana Street Northcote Auckland 0627 New Zealand Tel 64 9 481 0100 Fax 64 9 481 0101 Philips Selecon Europe Rondweg zuid 85 Winterswijk 7102 JD The Netherlands Tel 31 0 543 542516 www seleconlight com 2012 Philips Group
31. e cies Rives ec nent AR hte avid ra tnt bb tates te ie eine nine 37 ACCESSO Saaressa aens eeo eege ti Mir re ete ati die ee ee een 38 TROUBLESHOOTING Troubleshooting TE 39 TECHNICAL SPECIFICATIONS PL1 LED Luminaire Common Specifications cccccccsccssesseceecescesecesceeeeeceseeeeecseesaecaecsaeeaeceaeeeeeneeeeeneecaeestenaes 40 PLI LED Luminaire Dimensions wi sisi eme dde fiers ies abe ea eid E cadres detente lines tee 40 PHILIPS Selecon Installation amp User s Manual PL1 LED Luminaires PREFACE 1 About this Manual The document provides installation and operation instructions for the following products e PL1 LED Luminaires refer to Product Descriptions for individual product models Please read all instructions before installing or using this product Retain this manual for future reference Additional product information and descriptions may be downloaded at www seleconlight com 2 Product Descriptions This manual covers the following PL1 LED Luminaire models PL1 LED Luminaire Spot with Local DMX512 IR Control North American Market Part Number Description PL1RC01 TGO1 PL1 LED Luminaire Spot Global Track Adapter 2 circuit fitted White PL1RC01 T3G01 PL1RC01 TLOLO1 PL1RCO01 TLSI01 PL1RHCO01 PL1 LED Luminaire Spot Global Track Adapter 3 circuit fitted White PL1 LED Luminaire Spot Lightolier Track Adapter fitted White PL1 LED Luminaire Spot LSI Track Adapt
32. ed by hand Step 2 At luminaire head assembly as shown in Figure 7 open Accessory Ring holder by gently prying locking mechanism up with finger Lens Head Assembly Accessory Ring Locking Mechanism do not use tools to unlock open by hand only Barndoor Accessory Ring closed Filter Holder Accessory Ring opened Note Accessories sold separately Figure 7 PL1 LED Accessory Installation Step 3 Make sure accessory is positioned as desired in correct slot in holder and gently slide accessory into Accessory Ring holder Step 4 Swing Accessory Ring holder closed until it locks snaps into place Step 5 The luminaire is ready for use BEE PHILIPS 38 CLEANING AND CARE Selecon PL1 LED Luminaires Installation amp User s Manual TROUBLESHOOTING 1 Troubleshooting Guide The chart below provides possible causes and remedies for various error messages and or symptoms A WARNING Any service and maintenance including troubleshooting other than described herein should be performed by an Authorized Philips Selecon Dealer or Service Center Description Symptom Possible Cause Remedy No light output Fixture will not produce or output light Unit is set to Preset Off Make sure unit is set to proper Preset DMX command to 0 intensity Adjust intensity to higher level No power at luminaire DMX Data Control Luminaire does not power up Fixt
33. er fitted White PL1 LED Luminaire Spot fitted with a Half Coupler 39 inch AC Input Cable with User Specified Connector see note below White PL1RCTRO1 PL1 LED Touring Rental Spot Luminaire with a Lock Off Handle and C Clamp 39 inch AC Input Cable with Specified Connector see note below White PL1RC01 TGO3 PL1 LED Luminaire Spot Global Track Adapter 2 circuit fitted Black PL1RC01 T3G03 PL1 LED Luminaire Spot Global Track Adapter 3 circuit fitted Black PL1RC01 TLOLO3 PL1 LED Luminaire Spot Lightolier Track Adapter fitted Black PL1RC01 TLSIO3 PL1 LED Luminaire Spot LSI Track Adapter fitted Black PL1RHCO03 PL1 LED Luminaire Spot fitted with a Half Coupler 39 inch AC Input Cable with User Specified Connector see note below Black PL1RCTRO3 PL1 LED Touring Rental Spot Luminaire with a Lock Off Handle and C Clamp 39 inch AC Input Cable with Specified Connector see note below Black Note User specified connector supplied at time of ordering Refer to PL1 LED Luminaire Connectors North American Market on page 5 for more information PL1 LED Luminaire Spot with Local DMX512 IR Control International Markets 4 PREFACE Part Number Description PL1RT01 PL1 LED Luminaire Spot Universal 3 Circuit Track Adapter White PL1RT03 PL1 LED Luminaire Spot Universal 3 Circuit Track Adapter Black PL1RCO1
34. fixture using arrow buttons arrow buttons Once the values Cool White are adjusted the preset is saved Note To edit a current set preset as desired see Edit Presets a Day Light Only intensities may be stored on White Color Temperature presets RGBW in these presets cannot be edited or changed Continued next page Note See To navigate and access menu settings selections on page 16 to learn how to access menus To save changes hit OK Press ESC to cancel any changes you made PHILIPS 17 LCD Menu System Selecon Installation amp User s Manual PL1 LED Luminaires Menu Structure continued Continued from previous page Edit a Preset Sub Menu Options Comments Users can Off e Edit the current settings look toa specific recallable Preset in the fix ture s memory Edit the values for Red Green Blue White and Intensity values in percent by using the arrow buttons Scratch Pad Warm White Once the values are adjusted the Save Preset menu option Select Preset to Edit Option appears to save the edits Selects a current preset and outputs the preset so preset can be edited Cool White NOTES Only intensities may be stored on White Color Temperature presets RGBW in these presets cannot be Day Light edited or changed Note To save a specific look of the fixture see Save Presets If a Calibrated Preset s Color Mix is cha
35. g is a list of cleaning materials required to care for your PL1 LED Luminaire e Lint free lens tissue e Lint or powder free gloves e Reagent grade isopropyl alcohol e A mild soap solution Note Reagent grade isopropyl alcohol is good to use on the PL1 LED Luminaire plastic optics with anti reflection coatings If the lens is still dirty after using isopropyl alcohol for instance if fingerprints or oil is just redistributed and not cleaned off the optic then a mild soap and water solution can be used to gently wash the lens Repeat the cleaning with isopropyl alcohol to eliminate streaks and soap residue WARNING Under no circumstances should ammonia based cleaners acetone or other harsh solvents be used on or near the PL1 LED Luminaire These types of cleaners or solvents can permanently damage the optics or housings of the fixture If you have any questions regarding the use or care of your PL1 LED Luminaire please contact Philips Selecon technical support or your local Authorized Dealer Lens Cleaning Front Lens Exterior To clean the exterior front lens Step 1 Turn off luminaire and allow to cool completely Step 2 Apply a small amount of reagent grade isopropyl alcohol to lint free lens tissue Step 3 Wipe all debris dirt fingerprints etc from lens Step 4 Using a second lint free lens tissue wipe off any alcohol residue Front Lens Interior To clean the interior of front lens Step 1
36. ing Rose Mount WARNING All PL1 LED Luminaires must be mounted vertically as shown above to allow proper cooling Luminaire head may be positioned as desired PL1 LED Luminaire With AC Input Cable and Half Coupler Mount North American International Half Coupler Mount AC Input Cable Le PL1 LED Luminaire Shown with Half Coupler Mount Note Models with Half Coupler mounting hardware includes a 39 inch 1 meter AC input cable WARNING All PL1 LED Luminaires must be mounted vertically as shown above to allow proper cooling Luminaire head may be positioned as desired PHILIPS Selecon Mounting 13 Installation amp User s Manual PL1 LED Luminaires 5 Pan amp Tilt Adjustments To adjust pan and or tilt Step 1 At either pan or tilt locate Allen head screw as illustrated in Figure 1 Step 2 Using supplied Allen Wrench Tool part number ARLAKTOOL loosen but do not remove retaining screw Note Mount not shown Pan Retaining Screw 0 pee s for clarity Step 3 Position adjust pan left or right and or tilt up or down as desired Tilt Retaining Screw Step 4 Hand tighten but do not over tighten retaining screw Allen Wrench Tool Figure 1 PL1 Luminaire Pan amp Tilt Adjustment PHILIPS 14 INSTALLATION AND SET UP Selecon PL1 LED Luminaires Installation amp User s Manual OPERATION AND PROGRAMMIN
37. less DMX option is installed sold separately 1 Addr ss 001 to 512 001 DMX512 address Note it can be set if displayed Defines size precision of DMX map Color 2 Ma 8 bit 16 bit or 3 Chan 16 bit Mixing Intensity in 16 bit provides higher H i resolution for precision control 3 Chan provides minimal channel usage If DMX is detected and then goes away Off Hold Hold 8hr 8 this defines what will happen to the output 2 jun hours or Power Up Held At end of 8Hr hold Fixture goes to Power Up setting Fan Normal Normal Mode Provides higher cooling margin for thermally challenging applications Recommended for full power d A RGBW 100 applications with large 3 Normal Quiet Normal or Quiet Quiet and numerous changes in power Quiet Quiet Mode Quite Mode is similar to Normal mode but it controls fan tightly to reduce fan noise 3 Max 0 to 100 100 Sets the maximum fan speed 3 Min 0 to 100 1 Sets the minimum fan speed Display 3 Flip Display No Yes No Flips inverts Display and Keypad Arrows Note To Exit the Settings screen use the ESC key ESC and OK can be used to cancel or save changes to an individual parameter However once a parameter has been accepted by pressing OK that change cannot be undone canceled by pressing the ESC key OPERATION AND PROGRAMMING PHILIPS Selecon PL1 LED Luminaires Installation amp User s Manual DMX CONTROL This section contains information for opera
38. ls PLIRCO1 TG01 and PLIRCOI TG03 11 PL1 LED Luminaire Ceiling Rose Mount Models 13 PL1 LED Luminaire With AC Input Cable and Half Coupler Mount 13 Pan amp Tilt Adjustinemts ns ities chico hii icc ceive Rent es ete EE 14 OPERATION AND PROGRAMMING LCD Ment Operations EE 15 LCD MENU S Y SUSI errien e E EA E E etete sassevanetstecegeeadubeoiadeesaasnctaiviessceeaiatens 16 Mein Beet 17 e E 19 IN 19 Security Levels sas ccssvetceieodscetensetsasvaanhsetgut tank csideasenlestese o E EErEE E EEEE e Eeer 20 Eeckels 20 PLOSCUS nier ensure nee senavestaessdewiendvestivishdueghsvaansvtssduopeseevicnstsbenstevieseasshevoendk jdhiveupdeesuoneed 20 Presets NDS a eebe E ten let ee 20 Editing Preset Names ee 21 e 21 PHILIPS ho Selecon PL1 LED Luminaires Installation amp User s Manual DMX CONTROL HG SIS TEI OCS ES ie et te ta ees 23 Bit Te 25 DMX 3 Channel 3 Chan Mode ss issseneeneeeeeeeeeeeeeeeeneeneeeeneneeeensee 27 Lighting Console Settings for Preset White gedd KEEN EEN 28 PL1 Luminaire DMX Timing Channel Detail ss 28 INFRARED REMOTE CONTROL Infrared Remote Control Overview scien cated nm terrine tenait item nine en ir nement 34 Infrared Remote Control Features seen 34 CLEANING AND CARE Special Cleaning and Care Instructions seen 36 L NSEN 36 Front Lens EXteriOn sxccsceiess devs sated setine e ia aaen nenas EE nr tentent t enfant tentes tentent 36 Front Lens le BEE 36 Service and Maintenanc
39. na Der Inhalt dieses Handbuches ist nur fiir Informationszwecke gedacht Aenderungen sind vorbehalten Philips Selecon uebernimmt keine Verantwortung f r Fehler oder Irrtuemer die in diesem Handbuch auftreten F r Bemerkungen und Verbesserungsvorschlaege oder Vorschlaege in Bezug auf Korrekturen und oder Aktualisierungen in diesem Handbuch moechten wir Sie bitten Kontakt mit der naechsten Philips Selecon Niederlassung aufzunehmen Le mat riel d crit dans ce manuel est pour information seulement et est sujet 4 changements sans pr avis La compagnie Philips Selecon n assume aucune responsibilit sur toute erreur ou ommission inscrite dans ce manuel Pour tous commentaires ou suggestions concernant des corrections et ou les mises jour de ce manuel veuillez s il vous plait contacter le bureau de Philips Selecon le plus proche Note Information contained in this document may not be duplicated in full or in part by any person without prior written approval of Philips Selecon Its sole purpose is to provide the user with conceptual information on the equipment mentioned The use of this document for all other purposes is specifically prohibited Document Number 02 9692 0001 C Version as of 18 December 2012 PL1 LED Luminaire Installation amp User s Manual 2011 2012 Philips Group All rights reserved PL1 LED Luminaires Installation amp User s Manual IMPORTANT INFORMATION Warnings and Notices When using elec
40. nged 5 thru 25 an asterisk 7 is appended to the end of the name to indicate that it has been modified This only happens if the name matches the original calibrated name stored in EEPROM This does not happen if the Intensity is changed only the color mix Preset X 5 through 31 Note When DMX512 signal is present Edit a Preset option will not appear in menu structure Color Mix Sub Menu Options Comments Red Green Users can Edit Red Green Blue White and Select Color or Intensity to Adjust Blue Intensity values in percent by Option using the arrow buttons Once the values are adjusted White press OK to save the edits Intensity Note When DMX512 signal is present Color Mix option will not appear in menu structure Fan Control Sub Menu Options Comments Highlight Max button and hit OK Max button on menu Sets the maximum i speed of the fan Select and Set Fan Speed Option Level sets the fan to a constant speed will not vary Adjust level on fan Note hit Cancel to cancel an S speed level bar using Left and Right changes you made eee SES arrow buttons highlight Level button in menu and hit OK on menu to use user defined level Continued next page Continued next page PHILIPS 18 OPERATION AND PROGRAMMING Selecon PL1 LED Luminaires Installation amp User s Manual PHILI
41. ngs hit Learn button and then hit any Preset button except Off Off cannot be programmed Preset is now saved To cancel programming hit Cancel button Step 5 After programming or adjustments are complete hit Exit button Repeat as desired on additional luminaires to be programmed adjusted Note Refer to PLIIRR Remote Control User s Manual for additional information This manual is available on the Philips Selecon web site at www seleconlight com PHILIPS _ _ Se l eco n Infrared Remote Control Overview 35 Installation amp User s Manual PL1 LED Luminaires CLEANING AND CARE A WARNING All cleaning should be performed with power completely removed from the luminaire Never remove protective covers when luminaire is powered Wear appropriate protective eye wear and gloves when cleaning the fixture All service and maintenance other than described herein should be performed by a qualified technician or Authorized Service Center Special Cleaning and Care Instructions Being a solid state fixture and unlike most fixtures the PL1 LED Luminaire requires very little routine maintenance by the user This section covers portions of the luminaire that can be removed for cleaning The PL1 Luminaire requires special care when it comes to cleaning front lens assembly Additional care needs to be taken with the plastic components because they are much easier to scratch or damage than glass The followin
42. ol It is recommended that a qualified electrician perform this installation Additional Resources for DMX512 For more information on installing DMX512 control systems the following publication is available for purchase from the United States Institute for Theatre Technology USITT Recommended Practice for DMX512 A Guide for Users and Installers 2nd edition ISBN 9780955703522 USITT Contact Information USITT 315 South Crouse Avenue Suite 200 Syracuse NY 13210 1844 Phone 1 800 938 7488 or 1 315 463 6463 www usitt org Philips Selecon Limited Three Year Warranty Philips Selecon offers a three year limited warranty of its luminaires against defects in materials or workmanship from the date of delivery A copy of Philips Selecon three year limited warranty containing specific terms and conditions can be obtained from the Philips Selecon web site at www seleconlight com or by contacting your local Philips Selecon office PL1 s powerful LED engine offers exceptional performance and life Under normal operating conditions our LED engine has a life expectancy in excess of 50 000 hours however under worst case operating conditions with the luminaire set to continuous full output it is possible that a small percentage of LED s may require replacement sooner The Philips Selecon three year limited warranty includes our guarantee against premature failure of the LED engine PHILIPS Selecon Installation amp User s Manual PL1 LED
43. pear as follows note depending on which arrow button is pressed status screens may appear in reverse order a DMX Address note if fixture is UNLOCKED hit OK to change DMX address b Fixture Hours displays fixture operating hours since last reset c Fixture Power displays Max Power Limit setting in watts Present Power consumed by fixture in watts and Hours of Use d Fixture Status displays current operational temperature LED status and fan speed setting Step 2 Press LEFT or RIGHT arrow buttons to scroll through status screens Step 3 Press ESC at anytime to access menu settings See To navigate and access menu settings selections on page 16 a PHILIPS 16 OPERATION AND PROGRAMMING Selecon PL1 LED Luminaires Installation amp User s Manual Menu Structure PHILIPS Selecon PL1 PHILIPS ENTERTAINMENT V 0 01 A SIDE INTENSITY Esc MENU MAIN MENU Save as Preset Sub Menu Options Comments Select Preset to Save Option Off Scratch Pad Preset X 5 through 31 Users can Save the current settings look to a specific recallable Preset in the fixture s memory Edit the levels values for Red Green Blue White and Intensity Scrolls and sets current user defined Warm White color mix to various recallable presets values in percent by using the in the
44. rer s requirements and instructions for installation procedures For all models you must follow local and national codes for fixture installation PHILIPS INSTALLATION AND SET UP Selecon PL1 LED Luminaires Installation amp User s Manual Track Mounted Models PL1RC01 TLOLO1 and PL1RC01 TLOLO3 To attached adapter to ProSpec two circuit track Step 1 Select the CIRCUIT in ProSpec TRACK you want the fixture to be powered with Fig A by orienting the LEVER towards the side of the track of the selected CIRCUIT Fig B Step 2 With the CLAMPING TABS in the down position insert ADAPTER into ProSpec TRACK and flip the CLAMPING TABS up to secure the ADAPTER Fig C Step 3 To energize FIXTURE turn LEVER all the way until LEVER is parallel to ProSpec TRACK Fig D Step 4 To remove FIXTURE reverse procedure in Step 3 then flip down CLAMPING TABS and pull FIXTURE out of ProSpec TRACK DO NOT ATTEMPT TO RELEASE CLAMPING TABS before disconnecting power with LEVER WARNING NEVER PLACE FINGERS ABOVE THE BARRIERS ON THE CLAMPING TABS WHEN INSTALLING OR REMOVING FIXTURE Step 5 To change FIXTURE to second circuit remove FIXTURE as indicated in Step 4 then turn FIXTURE around 180 until LEVER is pointing to the other side of ProSpec TRACK and installed as indicated in Step Refer Figures for Track Mounted Models PL1RC01 TLOLO1 and PL1RC01 TLOLO3 Fig B CIRCUIT 1 CIRCUIT 2 CIRCUIT 1 4 CIR
45. s Table 1 PL1 LED Luminaire Voltage vs Current Voltage AC Total Current A 90 1 91 100 1 72 110 1 56 120 1 43 130 1 32 140 1 23 150 1 15 160 1 07 170 1 01 180 0 96 190 0 91 200 0 86 210 0 82 220 0 78 230 0 75 240 0 72 2 Connecting Power If the unit is supplied with an AC input cable Table 2 describes how to connect power to your PL1 LED Luminaire Field wiring of the PL1 LED Luminaire is straight forward A total of 3 wires conductors need to be brought to the unit The following wiring scheme is required Table 2 PL1 LED Luminaire AC Input Connections Wire Color Purpose Brown Main Line 120 to 240VAC Blue Neutral Green Yellow Ground 3 Connecting to the DMX512 Network Basic DMX512 installation consists of connecting multiple PLI LED Luminaires together up to 30 luminaires in daisy chain fashion A cable runs from the control console or DMX512 control source to the DMX connector on the first PL1 LED Luminaire Another cable runs from the other DMX connector on the first unit to a DMX connector on the next PL1 LED Luminaire or DMX512 device to be controlled PHILIPS eS ees Selecon Power Requirements 7 Installation amp User s Manual PL1 LED Luminaires Note For more information on DMX512 networking and systems refer to Additional Resources for DMX512 on page 1 For PL1 LED Luminaire DMX Mapping refer to DMX
46. sed if DMX the DMX Intensity channel is used for Intensity Presets Types Presets are classified as Locked Protected or User The type of preset determines what aspects of the Preset can be modified Locked Locked Presets are factory Calibrated at HE SSF ARE Cannot be changed by the user Their Intensity can be changed Three Presets 2 4 Warm White Cool White and Day Light are Locked PHILIPS 20 OPERATION AND PROGRAMMING Selecon PL1 LED Luminaires Installation amp User s Manual PHILIPS Selecon Preset 0 the off preset is also Locked to the OFF value Protected Protected Presets are also Factory Calibrated and by default are Protected from changes to their Color Mix Their Intensity can be changed Protected Presets are Presets 5 25 They can be Un Protected by setting Protected to No see section on Settings If Un Protected these presets function like User Presets The Factory Calibrated values for the protected presets can be re loaded to the original factory calibration settings by setting Load Factory to Yes see section on Settings User User Presets can have their Color Mix and Intensity changed without restriction Note If the Color Mix of a Factory Calibrated Preset is changed by turning protection Off an is appended to the end of the Preset s Name to indicate that the Calibrated values have been changed Editing Preset Names On the Edit Preset screen the option is
47. ses that the LED is operating over the specified temperature LED temperature is read and recorded through a thermistor imbedded in the LED chip Fan is not operating Listen for fan operation or adjust settings to increase fan speed On luminaires with a display check system status menu for status of fans and LED operation Password protection is on locked Input proper password to allow local programming and or adjustments Unit is controlled by DMX Disconnect input cables to check issue PHILIPS Selecon Troubleshooting Guide 39 Installation amp User s Manual PL1 LED Luminaires TECHNICAL SPECIFICATIONS 1 PL1 LED Luminaire Common Specifications Source Beam Spread Light Output Color Temperature Input Voltage Current Frequency Ambient Temperature Humidity Cooling Weight Compliance True RGBW 120 Watt LED chip 14 to 50 degrees gt 2 000 lumens 3000 5600K user adjustable 120V to 240V 10 auto ranging 1 91 Amps 90V 0 72 Amps 240V 50 60Hz 0 to 40 degrees C 32 to 104 degrees F 5 95 Non condensing Forced Air 8 0 Ibs 3 6 kg Luminaire only no mount AC input cable or accessories ETL cETL Listed North America models and CE Marked International models Note Common model specifications shown For specific model specifications features and accessories refer to the product specification sheet or visit the Philips Selecon web site at www sele
48. sole and or 3 Timing ee 02 100 255 manual fades Refer to PL1 Luminaire DMX Timing Channel Detail on page 28 for more information PHILIPS Selecon DMX 3 Channel 3 Chan Mode 27 Installation amp User s Manual PL1 LED Luminaires 4 Lighting Console Settings for Preset White 16 Bit Mode Below are the DMX512 console values and levels for Warm White Cool White and Day Light presets in 16 bit mode Red Channel Green Channel Blue Channel White Channel SES DMX omx DMX omx DMX Dmx DMX Dmx Warm White 65535 100 36700 56 0 0 47185 72 Cool White 65535 100 41287 63 8520 13 61603 94 Day Light 65535 100 53739 82 26214 40 58982 90 8 Bit Mode Below are the DMX512 console values and levels for Warm White Cool White and Day Light presets in 8 bit mode Red Channel Green Channel Blue Channel White Channel ss DMX omx DMX ous DMX ous DMX ower Warm White 3200K 255 100 163 64 0 0 217 85 Cool White 4000K 255 100 194 76 46 18 255 100 Day Light 5600K 255 100 237 93 130 51 255 100 Note Values and levels shown for Preset White in both 16 and 8 bit modes are approximate Due to the characteristics of LED technology actual values may vary slightly between fixtures PL1 Luminaire DMX Timing Channel Detail Timing channel control improves the timed moves of certain groups of parameters The PL1 LED
49. ting the luminaire using DMX control in 16 Bit 8 Bit or 3 Channel 3 Chan modes For Menu options and detailed information see Settings on page 21 Note These tables assume a DMX start address of 1 When a different starting address is used this address becomes channel function and other functions follow in sequence 1 16 Bit Mode Table 3 provides DMX channel mapping of all DMX512 control values when the PL1 LED Luminaire is in 16 bit DMX512 mode as set by the luminaire s menu system Table 3 PL1 LED Luminaire DMX Channel Mapping 16 Bit Mode Default recom Parameter Range DMX Range mended console Description default values DMX Channel Intensity High 0 65535 0 100 0 16 bit control for Intensity of LED settings Intensity Low Red High Byte Red Low Byte Green High Byte 0 65535 0 100 0 16 bit control of Red LEDs from 0 to full 0 65535 0 100 0 16 bit control of Green LEDs from 0 to full Green Low Byte Blue High Byte Blue Low Byte White High Byte White Low Byte 0 65535 0 100 0 16 bit control of Blue LEDs from 0 to full 0 65535 0 100 0 16 bit control of White LEDs from 0 to full SPlLOlLOINIODI ASRIJWI nN jo Used to access presets stored in fixture firmware such as CCT presets defined gel presets etc No Preset Activated DMX 0 3 DEFAULT Color Preset 0 Off DMX 4 7 Color Preset 1 Scratch
50. trical equipment basic safety precautions should always be followed including the following a READ AND FOLLOW ALL SAFETY INSTRUCTIONS AN Do not use outdoors Do not mount near gas or electric heaters aos Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by unauthorized personnel e The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition f Do not use this equipment for other than intended use g Refer service to qualified personnel SAVE THESE INSTRUCTIONS WARNING You must have access to a main circuit breaker or other power disconnect device An before installing any wiring Be sure that power is disconnected by removing fuses or turning the main circuit breaker off before installation Installing the device with power on may expose you to dangerous voltages and damage the device A qualified electrician must perform this installation WARNING Refer to National Electrical Code and local codes for cable specifications Failure to use proper cable can result in damage to equipment or danger to personnel WARNING This equipment is intended for installation in accordance with the National Electric Code and local regulations It is also intended for installation in indoor applications only Before any electrical work is performed disconnect power at the circuit breaker or remove the fuse to avoid shock or damage to the contr
51. ure will not respond to DMX commands Circuit not energized verify circuit breaker is turned on Not plugged in ensure A C cable is connected to power source Power cable wired incorrectly verify power cable and connector are wired correctly See Connecting Power on page 7 for more information Not detecting DMX data Disconnect and reconnect DMX input cable Unit is not set to be controlled by DMX check menu settings Check all DMX connections at control source and luminaire DMX data cable not wired correctly or has a broken conductor check DMX data cable for proper wiring See Connecting to the DMX512 Network on page 7 for more information IR remote programming LED light is getting dimmer Local programming Fixture will not respond to IR remote programming unit Fixture appears not to be operating at full brightness Unit will not allow local programming or changes Luminaire not selected by laser Reselect luminaire by repeating luminaire selection step Not seeing IR remote control Make sure batteries are good in remote Try fresh fully charged batteries Make sure IR is enabled in the fixture menu Insure IR remote is pointing at IR window in luminaire and that there is nothing in between IR remote and luminaire IR window Clean luminaire IR window Luminaire has detected an over temperature condition The luminaire will reduce power to its LED if it sen
52. vel Password on the Enter PassPIN line directly below the Security heading like Step 4 above Security Levels Security Level Description Default PassPIN 0 System is locked the only key that is active is the Menu ESC Key When this key is pressed a Not Applicable PassPIN is requested 1 All keys are Active 1111 You can select any Preset and change Intensity set DMX Address 2 Editing and Saving of Presets is added to Level 1 functionality 2222 3 Operationally the same as level 2 however all settings are available on the Settings screen 3333 Locking Fixture To lock the fixture Step 1 Ata Status Screen press MENU and scroll to Lock Fixture Step 2 Press OK Step 3 Use LEFT ARROW or RIGHT ARROW keys to highlight YES press OK Step 4 Fixture is now locked Note When the Fixture is Locked only the ESC MENU key is functional Pressing this key will display a request for a password When a valid password is entered the fixture is unlocked to the security level of the entered password Presets Presets are Color Mixes that are stored in the Fixture they can be recalled to reproduce a specific output from the fixture Presets are made up of a Color Mix Red Green Blue and White They also have Intensity associated with them Presets can be recalled via the User interface or by a DMX channel when under DMX control The Preset s Intensity is applied if the User Interface is u

PL1 LED Luminaire (Discontinued) - Installation

Contents

Download Pdf Manuals

Related Search

Related Contents