"user manual"
Contents
1. X Relay is optional only for install in DC ignition motorcycle Troubleshooting 1 Transmitter is ineffective or the control distance decreased significantly Tall building radio tower or high freguency electromagnetic wave may affect the control range Low power of the battery The transmitter is broken or damaged The installation location of the antenna is wrong You should straighten the antenna and keep it away from other wire harness 2 The siren does not chirp when the alarm system is triggered The wire connection between the siren and ECU has problem The siren is damaged 3 The system gives false alarms when heavy vehicles by passing The sensitivity of the sensor is too high 4 The continuous chirping of the siren cannot be stopped by transmitter after the installation of ECU The plug is improperly inserted The wire is improperly connected The siren is damaged 5 If the problem persists please follow these steps For consumer contact your dealer or nearby service centre For installer or dealer email your question to us and we will reply ASAP2. the more the bar the stronger the signal When the transmitter can not receive the signal fron the system the signal bar will disappear 16 Sensitivity adjustment by transmitter In disarming mode press and hold 8 buttons or X button to enter the shock sensor sensitivity setting function Press w button or qX button to change the 1 8 sensitivity levels level 8 is the highest sensitivity levels level 8 is the highest sensitivity level and level 1 is the lowest sensitivity level When selecting sensitivity levels the siren beeps once with turn signals flashing once to indicate the sensitivity is at level 1 the LCD transmitter will monitor 1 the siren beeps twice with turn signals flashing twice to indicate the sensitivity is at level 2 the LCD transmitter will monitor 2 and so on Once the suitable sensitivity is set press 8 button to confirm and exit the setting mode If there is no adjustment within 15 seconds after the system enters the sensitivity setting mode the system will automatically exit setting amp revert to its former sensitivity status Factory default level 5 17 Backup battery optional A backup battery provides power to the system when the primary source of power is unavailable 18 Monitoring the battery status of the motorcycle Every time when press armed button on the LCD transmitter the battery voltage of the motorcycle will be shown on the transmitter with V icon flashing You can kn
3. times with vibration the amp icon and icon will be flashing with backlight Ifthe second shock impact triggered in 15 seconds the siren will chirp 15 seconds with turn signals flashing and the engine will be immobilized The 2 awy transmitter will beep and vibrate the amp icon and amp icon will be flashing with backlight X In mute arming mode the siren will not chirp 4 Emergency alarm In arming mode if the key is turned to ACC ON position the siren will chirp sharply the turn signals will flash and the engine will be immobilized press 8 button to stop alarming 5 Disarming and rearming In arming mode press 9 button to disarm the system If the motorcycle is not touched or the enging is not started in 30 seconds the system will automatically return to the former arming mode Press 8 button twice the turn signals will flash twice and the system will be disarmed completely 6 Locating Press amp button once or press and hold 8 4X 8 4 buttons to locate motorcycle the siren will chirp for 10 seconds with turn signals flashing 7 Anti hijack Ignition on press and hold amp or x button the siren will chirp sharply with the turn signals flashing The engine will be immobilized after 10 seconds Press button to stop this function 8 Not armed warning When the ignition off and the system is not armed within 10 seconds the siren will chirp 3 times with turn signals flashing to remind to arm the syst
4. STEEC MATE Automotive 2 WAY Motorcycle alarm system nia saia dala SAMa Manual User s Manual Installation Manual Important notice 886 series installation guide Key features 986 series installation guide Technical parameter ECU installation Brief look at each device ECU light installation Transmitter charging Siren installation Low battery warning Troubleshooting Functions Important notice Technical parameter Transmitter charging e Please install the system by an authorized ECU engineer Operation voltage 12V23V e Keep the product and the transmitters from Static current lt 3 5 mA water Operation frequency 433 92 MHz e It is highly recommended you read this manual Connect the charger s plug to transmitter s charging socket and then insert the charger into 100 240V power supplier the transmitter s battery can be charged discontinuously When transmitter is full charged the battery indicator will be full Siren carefully before the installation and operation of Siren SPL 108 125 dB this unit e When the transmitter operating distance is shorter or its indicator light turns dark please replace the baitery with a new one or charge the transmitter ASAP Transmitter Operation voltage 3 2 4 2V Rechargeable 1 1 1 5V AAA battery Brief look at each device Key features 3 Arm Press 8 button once to arm the system Low battery warning 2 way LCD transmitter e Motorcyc
5. em 9 Remote stop engine During driving or starting engine press 8 button once to stop the engine 10 Remote engine start 986 series only Press w button twice continuously the engine will be started and run for 8 minutes then engine will be shut down and the system sill return to the previous status During the 8 minutes if you insert the key and turn to ACC ON the engine will keep running 11 keyless driving 986 series only If the engine is started press w button again in 8 minutes the siren will beep once to confirm that the motorcycle can be driven with keyless When the engine is running press 9 button once the engine will be stopped 12 LED indicator In arming mode the LED indicator will flash once every two seconds When shock sensor is triggered the LED indicator will flash continuously 13 Special music reminding Press any button on the transmitter if it sends out special music the transmitter is communicating with ECU please operate it later 14 Time setting Press 8 9 button together for 2 seconds the transmitter beeps once the figure will flash the press 8 button to choose hour or minute setting and set the time by 8 button Parameter setting 1 Time setting hour minute time in 24 hour notation 2 Exit press 848 button together to save the setting and exit the setting mode the transmitter beeps once 15 Antenna range indication Antenna range shows by bar on the LCD screen
6. le battery status indication on LCD transmitter Low power consumption lt 3 5 mA Shock sensor sensitivity adjustable via transmitter e Water resistant ECU e Out of operating range warning e Small siren amp ECU for easy installation e Backup battery optional Press 8 button twice to enter mute arming mode 8 Disarm Press 8 button to disarm the system Press and hold 8 button to turn on off transmitter Rechargeable transmitters A Start Press w button twice to start the engine qX Mute Press amp X button to arm in mute arming mode amp Panic Press amp button once to locate the motorcycle X Some buttons are only for some transmitters When a transmitter s battery is low the transmitter will send out warning sound after the button is pressed the battery indicator will show the battery status When the battery indicator is empty the transmitter needs to be charged or changed immediately od Battery is full Battery is low Battery is empty X The transmitting range will be affected when the battery is low 1 Arming When ignition is turned to off press 8 button to arm the system 2 Mute arming Press 6 button twice or X button once to enter muet arming mode 3 Shock impact alarm In arming mode the first shock impact will trigger the system warning the siren will chirp with turn signals flashing 3 times and the engine will be immobilized The 2 way transmitter will beep 5
7. ow the motorcycle s battery status at any time Installation Manual 886 series installation guide AC ignition installation diagram ow oo ax oc ke o D ct o lt White Red Yellow Flameout wire Turn signal Turn signal Battery DC ignition installation diagram w o o A o w o A ke eg D o lt T c n o Dark green Red Yellow mmm Battery Engine lock Not need connect Flameout wire Turn signal Turn signal Battery 986 series installation guide AC ignition installation diagram 19208 Aieneg dnyoeg Dark green Red Battery Orange Engine lock Flameout wire Turn signal Yellow Turn signal Blue Start engine only for 986 series Black Battery ECU installation Siren installation DC ignition installation diagram Please mount the Please mount the siren downwards as shown in ECU downside as the figures 1 or 2 below shown in the figure Red Orange Not need connect n o o A o w D o xy D o amp D lt Flameout wire Turn signal Yellow Turn signal 1 Drill a hole 08 around the block where it can be seen clearly 2 Insert the outer bushing to the hole ob un 3 insert the inner bushing with LED to the outer bushing and tighten them up Battery 4 Connect the LED plug to the main unit of the alarm system
Download Pdf Manuals
Related Search