BEETLE /iSCAN Tower Line 150
Contents
1. 203 CINEO Tower TL150 22 Important Notes Site Preparation and Commissioning Opening the Cash Module 6010 with safe Enter the key into the lock 1 turn it clockwise and open the front door 23 Important Notes Site Preparation and Commissioning Open the cash module see page before Enter the safe code 1 turn the locking release handle clockwise 2 and open the safe door Closing the Safe Close the safe door and turn the locking release handle of the safe door counterclockwise as far as possible 24 Important Notes Site Preparation and Commissioning Push the green release lever at the right side of the safe unit up 1 and pull it out Now the screws to fix are reachable next page 25 Important Notes Site Preparation and Commissioning Opening the Cash Module 6010 no safe i Only touch green the marked handles and knobs for moving parts Unlock the unit 1 and pull out the carrier completely 26 Important Notes Site Preparation and Commissioning Pulling out CINEO 6010 Open the front door page Pull the green lever upwards 1 Pull out the cassette carrier to the stop 27 Important Notes Site Preparation and Commissioning Straight alignment and fixing the Cash Tower CINEO 6010 The Cash Tower must be adjusted before the final fixing max 1 tilting to front See at the picture below which screws are necessary to do that 1 Adjus2. Always unplug the power cord before installing or removing any assemblies Always handle assemblies by their edges Never touch the terminal pins of the circuits on an assembly Important Notes Site Preparation and Commissioning Important Notes Appliances supplied by Wincor Nixdorf International GmbH comply with the respective safety regula tions for data processing installations and information technology installations including electrical office equipment for use within an office environment A Whenever work of any kind is done on the device as well as when data cables are plugged and unplugged the device must be completely disconnected from the line voltage If UPS is installed you must switch off this too to separate BEETLE ISCAN Tower Line 150 from power completely Appliances may only be repaired by authorized technicians Unauthorized opening of the housing or inexpert repairs can result not only in considerable personal danger but will also invalidate your warranty and liability protection Always consult the enclosed documentation before doing any work with this appliance If this device is brought from a cold environment into a heated place of business condensa tion may occur Before operation the device must be completely dry Therefore an acclima tization period of at least two hours must be adhered to Always lay the supply leads and cables in such a way that they cannot be stepped on or tripped
3. Note In Note out out Di Receipt Receipt 14 PoleLigt 14 Pole Pole Light Basket Shelf ard READE Coupon In 15 Bag Holders oo D 4 Housing Lock Lock 8 Attendant Lock Housing Lock Lock e Security Scale Security Scale The Pin Pad is customer specific different models and positions are possible Different Hand Held Scanners may be used Different Card Readers in different positions are possible Important Notes Site Preparation and Commissioning Components CINEO 6010 oe Pole Light G Basket Shelf agih Housing Lock D Screen e Attendant Lock Lock Di Conin In D Note Note In Note Out Out GE D Senneng Pin Pin Pat Pin pat me Security Scale Scale The Pin Pad is customer specific different models and positions are possible Different Hand Held Scanners may be used Different Card Readers in different positions are possible 10 Important Notes Site Preparation and Commissioning Unpacking and Checking the System Unpack the system and verify that the scope of delivery is identical to the information on the delivery ticket Should you notice any e transport damages or e discrepancies between package contents and delivery ticket or e functional defects please inform your contracting parties or the branch office of Wincor Nixdorf immediately Please indicate the number of your delivery ticket and delivery ticket position and serial number of the re spective device D It is ab
4. Opening the Cash Module GO10Inosatel 26 PUNE OGL CINEO GOTO nonsi N a 27 Straight alignment and fixing the Cash Tower CINEO GO 28 REMOVING the Transporation LOCK E 29 D Ku RR EE 29 EC AG I DE 29 COCO OTE EE 30 CONMCCEIME TMS SY EE 31 See 31 Power Connection and LAN SUDOOFE EE 32 Disconnecting the System from the Mans sssessssssssnsssrrnssrresssrrresrrressreressresssreresererssreressrereseeresereeseeere 34 PADHET aaa aaa NU a A IE Oa A ener T A BA E Oe eh A aa a BA eee ere 35 PUPER Er DOCUIMEMUALION EE 35 Dijaja e E ee e 35 Maintenance and SEI VIC E a itso a D Ng EN el ear et sacs hatin ed a Aa tae Gg A Ta ark ue ae 35 Approved Cleaning EECH 36 BEETLE iSCAN Tower Line 150 DiIMeNSiONS ccccccesseccccesscccceesececcesscceceusececeeececeeecsessusesecsunsess 36 BEETLE iSCAN Tower Line 150 DiIMeNsSiON ccecccesseccccesseccceeseccceesscecceesececsuececseeceensusesecsunsess 37 BEETLE iSCAN Tower Line 150 Service Area 37 BEETLE iSCAN Tower Line 150 bi optical NON Cash 38 BEETLE iSCAN Tower Line 150 vertical NON Cash 40 BEETLE iSCAN Tower Line 150 CINEO GO 41 Block KE WEE 43 BEETLE J 1SCAN Tower LING 50 Bi Op tl Cal Ee NGA ea nc ds AND NE NA a ENEE 43 BEETLE iSCAN Tower Line 150 Vertical ccccccesscccccsseccccessccccesssceceesceceescccseeseseceeesceceesseesenss 44 Sage tele ECK eet Tee 45 NGNE EE 45 RRE NIT eg ge ENKE E e EE 46 Note on Radio Interference Suppression 46 FC
5. Line 150 Further safety installation and maintenance instructions can be found in the manuals supplied with the components In case of doubts or questions please contact Wincor Nixdorf International WN Important Notes Site Preparation and Commissioning Warranty Wincor Nixdorf guarantees generally a warranty engagement for 12 months beginning with the date of delivery This warranty engagement covers all damages which occur despite a normal use of the product Damages because of improper or insufficient maintenance improper use of the product or unauthorized modifications of the product inadequate location or surroundings will not be covered by the warranty For further information on the stipulation consult your contract All parts of the product which are subject to wear and tear are not included in the warranty engage ment For detailed warranty arrangements please consult your contract documents ESD Electrostatic Sensitive Devices Assemblies containing electrostatic sensitive devices ESD may be A labeled with this sticker AN When installing an assembly or drive please follow the guidelines below which apply to all electro static sensitive devices ESD Make sure you are not carrying a static charge before working with components marked as ESD by first touching a grounded object such as a radiator from a hot water heating system All tools and devices you use must be free from static charges
6. TN S network Do not use PEN conductors Also follow the recommendations set forth in DIN VDE 0100 Part 540 Appendix C2 as well as EN50174 2 5 4 3 This will help prevent malfunctions National Electrical Code ANSI NFPA 70 2005 Canadian Electrical Code Part CSA C22 1 02 When working on the cutter of the printer the device must be turned off Always keep the ventilation slots free of obstruction to ensure adequate air circulation and avoid overheating Transport the appliance only in its original packaging to protect it against knocks and bumps falithium battery is supplied with the appliance ensure that the battery is replaced with an equivalent type Otherwise there is danger of explosion Lithium batteries may only be re placed with identical types or other types recommended by the manufacturer Batteries must be disposed of according to local regulations on the disposal of special waste Connecting Peripherals Use only shielded cables when connecting devices to the system to ensure compliance with international Rules and Regulations for radiated emission as well as to achieve a high immun ity against external disturbances Coin Module Care should be taken to keep fingers clear of the hinged chassis panels when dumping coins or rotating the hoppers to gain access to the inside of the unit This area is a potential pinch hazard and may cause significant injury when using hoppers filled with coins Win
7. 0 5 K min max 7 5K 30 min 25 C 60 C 15 r h 1 g m 98 r h 32 g m 25 C 25 C Weights TL 150 Vertical approx 75kg TL 150 Bioptical approx 95 kg TL 150 CINEO no safe approx 160 kg TL 150 CINEO safe approx 292 Kg 45 Important Notes Site Preparation and Commissioning Certifications of the Manufacturer gw This device complies with the requirements of EMC directive 2004 108 EC with regard to Electromagnetic Compatibility and 2006 95 EC Low Voltage Directive Therefore you will find the CE mark on the device or on its packaging Devices without integrated UPS according class B Devices with UPS according class A Important Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Note on Radio Interference Suppression All secondary appliances that are connected to an appliance must be equipped with radio interfer ence suppression in accordance with EC directive 2004 108 EC Products that fulfill this requirement are accompanied by an appropriate manufacturers certificate bear the CE symbol or the radio pro tection symbol Products that do not fulfill these requirements may only be operated with specific permission of the relevant authorities FCC Class A Declaration This equipment has been tested and found to comply with the limits for a Class A digital device pur su
8. 01 certified as is the entire company 3 A For recycling purposes do not attach any addition 4 al adhesive labels to the device Follow your local regulations on the disposal of toxic waste such as the system ribbons Your Wincor Nixdorf vendor will answer any questions you have concerning returns recycling and disposal of our products 47 Wincor Nixdorf International GmbH D 33094 Paderborn Order No 01750159234D
9. CG Class A Declaration saanak a Bad aa b baga bs ee a si yh a 46 Recycling the BEETLE iSCAN Tower Line 10 47 Important Notes Site Preparation and Commissioning Introduction The BEETLE iSCAN Tower Line 150 is a terminal that offers a customer to handle the purchase by scanning bagging and paying the items on his own In case of problems an attendant is available for quick support BEETLE iSCAN Tower Line 150 offers the following main functions Record function records items the customer wants to buy Control function secures the recording of all items Payment function payment may be effected by banking cards customer cards and ac counts coupons bank notes or coins Cash return uses bank notes and coins About this manual This manual refers to technically trained personnel only It provides all necessary site preparation information for installing BEETLE iSCAN Tower Line 150 at your site D Notes are marked by this symbol Caution Identifies action requiring caution The responsibility for all technical and special prerequisites for installation of BEETLE iSCAN Tower Line 150 is borne by the customer A detailed list of customer responsibilities is given in this manual Installation as well as connection of BEETLE iSCAN Tower Line 150 may only be executed by techni cally trained personnel The safety instructions given in this document should be strictly followed when handling BEETLE iSCAN Tower
10. Support The BEETLE iSCAN Tower Line 150 supports Ethernet 10 100 BASE T local area network LAN com munication protocol The BEETLE terminal provides a female RJ 45 connection port for the LAN A 6 foot LAN cable is provided with the system There are three possible positions to connect the BEETLE iSCAN Tower Line 150 to the power supply from the bottom from the back side and from the side Connect the rubber connector to the socket outlet and the LAN cable to the LAN socket sockets at the side of the device Push the button at the power distribu tor to position 1 Scan Module vertical Open the device Find the button at the bottom of the housing 32 Scan Module bi optical Open the device Find the button at the bottom of the housing iCash10 Cash Module Open the device Press the Power On switch to the position 1 iCash15E Cash Module Remove the cover arrow carefully with a small screwdriver and start up the device position1 CINEO Cash Module with safe Remove the cover arrow carefully with a small screwdriver and start up the device position Important Notes Site Preparation and Commissioning 33 Important Notes Site Preparation and Commissioning CINEO Cash Module without safe No action necessary Deviations from illustration possible After starting up the system you will see the start screen of the operating system Disconnecting the Sys
11. WINCOR NIXDORF Important Notes Site Preparation and Commissioning Edition 2015 All product names mentioned in this document are registered trademarks Copyright Wincor Nixdorf International GmbH 2015 All rights including the rights to the translation reprinting transmission or copying by any means in whole or in part are reserved Offenders will be liable for damages All rights including rights resulting from a patent grant or registration of a utility or design are reserved Contents Haid gale 8 cdi oq kna a AN KA aaa a Ka a ana a pnt Naren a err Ten KB A a aaa er meer a ren ee 1 eier Die IER un ET EE 1 NET EEN 2 ESD Electrostatic Sensitive DEVICES En 2 IMPO gang Lee 3 Klenge EE 5 Ree 6 CUSTOMEer REEL 7 Components Device with bi optical Scanner 8 Components Device with vertical Scanner 9 COMPpPOMents CINEO GOTO EE 10 Unpacking and CHECKING The EE 11 installing the lower Line 150 mthe Store ain aa Wae cea a Naba TA a A KAN ag a KA aa E KA alah 12 Removing the Back Panel at the Scan Module bi optical 13 Removing the Back Panel at the Scan Module Vertical cccccsseccecssecceeessececeeseceeseeeceeseesecesseneees 15 Removing the Back Panel at the Cash Module iCASH 10 iCASH IEN 16 Removing the Back Panel at the Cash Module CINEO GO10 cc cecccccssseccceeseceeeeeceeseeseceeeeneees 18 JE eelere 20 PIKING THe DEVICE at the FOO E 22 Opening the Cash Module 6010 with Sate kasian Ena a AAN KN ee A eas 23
12. ant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Modifications not author ized by the manufacturer may void users authority to operate this device This class A digital appa ratus complies with Canadian ICES 003 Cet appareil numerique de la classe A est conforme la norme NMB 003 du Canada 46 Important Notes Site Preparation and Commissioning Recycling the BEETLE iSCAN Tower Line 150 A The BEETLE iSCAN Tower Line 150 was designed A 4 according to the Wincor Nixdorf standard 4 N Environmentally Conscious Product Design and l 4 ag Development q oo ia The BEETLE iSCAN Tower Line 150 is manufac 4 A tured without the use of CFCs and CCHs and is y A manufactured to a great extent of materials and j components which are recyclable NG 4 N Keen k N K x Wincor Nixdorf disposes of old devices in an envi ronmentally responsible manner at a recycling center that is ISO 9001 and ISO 140
13. cor Nixdorf International will not be held liable for damages and or personal injuries brought on by incorrect operation and maintenance practices Only a qualified service technician should replace an individual hopper assembly or remove the PCB protective shield to access internal components Ignoring this warning may void the products warranty AN Critical Shock Hazards indicates potentially lethal voltages are present The coin recycling unit weighs approximately 24 kg and 210 kg filled with coin When transporting the unit avoid bumping or dropping it which could damage the unit The coin recycling unit should be emptied before transporting Any drop on a body part could cause serious personal injury The collection cassette of the note recycling unit weighs approximately 7 5 kg w o notes Any drop on a body part could cause serious personal injury Important Notes Site Preparation and Commissioning Note on Laser The barcode readers contain a light emitting diode LED classified according to LASER CLASS 1 IEC 60825 1 1993 A1 1997 A2 2001 EN 60825 1 1994 A11 1996 A2 2001 Important Notes Site Preparation and Commissioning Tools you need Keep the following tools at hand for working on the BEETLE iSCAN Tower Line 150 Socket wrench 5mm Allen screw H3 H4 H5 Jay wrench 5 5 7 8 mm and 17 mm adjustment Flathead screwdrivers two sizes Phillips screwdrivers Flathead screw driver Torx screwdrivers hexago
14. ews at the rear side close the device at both sides and lock the front door before you tilt the BEETLE iSCAN from the pallet Always remove the device with two persons and with the help of the ramp from the pallet Unlock the front door of the cash module and pull out the carrier completely i 5 18 Important Notes Site Preparation and Commissioning Remove the two screws fixing the cover in it s position Remove the back panel upwards and remove the fixing screws from the pallet 19 Important Notes Site Preparation and Commissioning Installing the Security Scale Unpack the security scale Place it nearby the final installation place at the BEETLE iSCAN Tower Line 150 Remove the LAN Power connection cover at the Scanning unit Behind the cover you find the COM cable to connect the security scale Plug the COM cable to the COM cable which you find in the security scale housing Aan k ke x pal e St Ze ah AR Ge e sch 6 Ari TC ast st HASS ing el Re Leet Ee lt The security scale must be installed at the BEETLE iSCAN Tower Line 150 with max 4 screws see picture below 20 Important Notes Site Preparation and Commissioning Put the cover and the bag holders on the security scale AN Caution After mounting the security scale it must be adjusted by authorised personnel only 21 342 Important Notes Site Preparation and Commissioning Fixing the Device at the Floor
15. he Scan Module bi optical Unlock the door and pull out the carrier completely Remove the two screws fixing the cover A Caution After removing the screws close the device as far as possible to avoid an uncontrolled tilting of the system after removing the fixing screws at the rear side Keep the carrier as close as possible After removing the screws at the rear side close the device at both sides and lock the front door before you tilt the BEETLE iSCAN from the pallet Always remove the device with two persons and with the help of the ramp from the pallet WINCOR NIXDORF Pull the cover forwards to the stop WINCOR d LALA kn NIXDORF ES Crac Op ae ege Gef em em 8 KU i Au i VO H d ES eeneg ee ee R Ehe 13 14 Important Notes Site Preparation and Commissioning Lift up the back panel Mount the back panel in reverse order Important Notes Site Preparation and Commissioning Removing the Back Panel at the Scan Module vertical AN Caution After removing the screws close the device as far as possible to avoid an uncontrolled tilting of the system after removing the fixing screws at the rear side Keep the carrier as close as possible After removing the screws at the rear side close the device at both sides and lock the front door before you tilt the BEETLE iSCAN from the pallet Always remove the device with two persons and wi
16. he packaging and on the information sheet included in the packaging The product may be damaged or soiled if materials are used that are not approved or if they are used improperly 36 Important Notes Site Preparation and Commissioning BEETLE iSCAN Tower Line 150 Dimensions BEETLE iSCAN Tower Line 150 Service Area eae e e e e mm rm mm mm remm mm mmm mmm mmm mmm mm mm mm eee SS mm mmm emm emm mm mmm mmm mm mmm mm mmm mm mmm mm mm mmm mm mmm mmm mmm mmm mm l mama l mami 005 05411 SX Jamojueos5 Ur yy6ua vol fuayxa RE 068 7 60 ULI OINI 164 00 005 BIIAJIS JUOUY J0 eave aIIAUaS yIeG JO eave l L l 37 Important Notes Site Preparation and Commissioning BEETLE iSCAN Tower Line 150 bi optical non Cash 38 1120 Important Notes Site Preparation and Commissioning max 847 Sa pel 711 343 600 4 4 p NG m lt 430 d j 5 WM for GI C ve CH N 00 CH N E Kam Ei E Q T K Ka 0 i En L 1540 39 Important Notes Site Prepa
17. n round screwdrivers Important Notes Site Preparation and Commissioning Customer Requirements Before BEETLE iSCAN Tower Line 150 installations can be started the customer is held responsible to provide the following A If more than ten Self Checkout Systems Lanes are to operate in one configuration they have to be connected to a network via an ISCAN server with a performance matching the requirements Appropriate drawings concerning location of the equipment as well as site wiring power and communications paths and lengths Location of other equipment that may generate electri cal noise electromagnetic interference or heat Provision and installation of all communication cables wall jacks special connectors and as sociated hardware Provision and installation of necessary power distribution boxes conduits grounds lightning protection devices and associated hardware Ensure that all applicable codes regulations and laws including but not limited to electri cal building safety and health are adhered to Provision and installation of auxiliary power or other equipment as required Provision of storage or service as required Provision of a level floor to locate the BEETLE iSCAN Tower Line 150 The system has to be stable and must not tilt The maximum incline must not exceed 2 The feet of the unit can overcome a height difference of up to 10mm Provision of an installation location that will p
18. over Only touch green marked handles and knobs for moving parts Exchange damaged cables immediately In order to completely disconnect the device from the power source turn the device off and use the separator in the fuse box building installation Make sure that no objects such as paper clips can reach the interior of the device since electrical shocks or short circuits could result To avoid overheating of the power supply unit Ensure that the BEETLE iSCAN Tower Line 150 receives adequate ventilation During an electrical storm data cables should not be plugged in or unplugged Keep the device away from airstreams ventilation vibrations dust humidity and heat Ensure that used parts are disposed of in an environmentally friendly manner In case of an accident such as a damaged housing entry of liquids or foreign objects switch the device off and use the separator to completely remove the device from power BEETLE iSCAN Tower Line 150 is the result of state of the art technology Therefore please also ensure that the BEETLE iSCAN Tower Line 150 is operated under modern building and Important Notes Site Preparation and Commissioning technical conditions in order to ensure flawless and efficient operation The appliance and other information technology hardware should only be connected to electrical supply net works with a separate protective earth wire PE This type of electrical supply network is re ferred to as a
19. ration and Commissioning BEETLE iSCAN Tower Line 150 vertical non Cash Area for Service he fa og nd extention lenght 40 Important Notes Site Preparation and Commissioning BEETLE iSCAN Tower Line 150 CINEO 6010 _ IN 4 al jw 41 Important Notes Site Preparation and Commissioning 42 Important Notes Site Preparation and Commissioning Block Diagram BEETLE iSCAN Tower Line 150 bi optical ae 1s Kon ngayeg iag HEE pid a A AJB boy aa i E Ces SARA KET a D pa T i a a ANGEN 43 Important Notes Site Preparation and Commissioning BEETLE iSCAN Tower Line 150 vertical 44 96 H id Aa PSUs324V a G E COL ver Cin Mach Ta vasi ON er HK vert Gran TON wie vt ao a gt cw 2 TAI Environmental Conditions Operating conditions Ambient temperature Humidity Temperature change Barometric pressure Important Notes Site Preparation and Commissioning 5 C 35 C 5 r h 1 g m 85 r h 25 g m 0 5 K min max 7 5K 30 min 70 kPa 106 kPa Installation environments with long periods of sunshine should be avoided Storage conditions Ambient temperature Humidity Temperature change Transport conditions Ambient temperature Humidity Temperature change 5 C 40 C 5 r h 1 g m 85 r h 25 g m 0 5 K min
20. revent the security scale optional from being influenced by heavy air movement and resulting weight irritations If this is not possible the following measure needs to be applied Build a windshield around the scale Provision and installation of floor coverings and environmental systems that limit or control Static electricity build up and discharge Provision of appropriate equipment for the remote support The customer is responsible for relocating the Self Checkout equipment check stand and compo nents to the final placement installation position Keep the Wincor Nixdorf equipment area free from ventilation dust smoke lint and other particles Restrict smoking eating and drinking around the equipment Avoid locating the equipment near other machines that generate ink carbon and paper dust particles i Please note that Wincor Nixdorf will not take over any warranty liability in case the technical and environmental requirements are not met Important Notes Site Preparation and Commissioning Components Device with bi optical Scanner e reet Jean iess 2 misono 6 eer Ir leen irae DECHE The Pin Pad is customer specific different models and positions are possible Different Hand Held Scanners may be used Different Card Readers in different positions are possible Important Notes Site Preparation and Commissioning Components Device with vertical Scanner a D Conn In e Note IniNote out
21. rge this equip ment must first be disconnected from the power supply Besides switching off the power switch on the power distributor the safety plug must be disconnected from the power distributor Device Housing Clean the housing with a vacuum cleaner or cloth Eliminate damage to paint if necessary and possible 35 Important Notes Site Preparation and Commissioning Approved Cleaning Materials The items listed below can be ordered from Wincor Nixdorf branch office or your Wincor Nixdorf sales partner Product Name Order Number Explanations Professionell cleaning set for 01750097335 For cleaning and maintaining keyboards EDP devices and varnished and plastic coated hous ing 100ml plastic cleaner in a pump bottle 50 dust cloths 10 keyboard swabs for places difficult to reach Damp cleaning cloths 01750097332 For cleaning and maintaining delicate EDP devices keyboards and housing Dispenser box with 100 cloths Dry cleaning cloths 01750097334 For cleaning display panes Antistatic and fluff free Pack with 300 cloths Compressed air spray 01750097331 Cleaned compressed air FCKW free for removing loose dust and dirt PRESSAIR particles 400ml bottle without a valve 70cm hose Cloth with ISOPROPYL 1000 01750104065 Pure isopropyl alcohol for cleaning pieces display Cleaning card 01750016388 For cleaning magnetic heads and chip contacts in ID card readers Please note the manufacturer s specifications on t
22. solutely necessary to check the function of the original equipment before you perform any changes e g by installing an expansion card Only then it is possible to accept a functional defect as a claim i We recommend to save the original packaging for transport at a later time protection from impact and shock 11 Important Notes Site Preparation and Commissioning Installing the Tower Line 150 in the Store The BEETLE iSCAN Tower Line 150 will be delivered on a pallet with a size in industry standard 1000mm x 1200mm First remove the wrapping paper The device is fixed at the pallet with 8 screws Another eight screws are to adjust the device at the designated site AN Caution At first remove the fixing screws at the front side of the device To reach the screws in the back of the BEETLE iSCAN Tower Line 150 you have to remove the back panels of each module see next pages CY These screws are to adjust the device OS Remove these screws to tilt the BEETLE iSCAN Tower Line from the pallet AN Caution Always wear safety gloves and safety shoes with steel toe caps while transporting heavy appliances AN Caution Tilt the device max 15 very carefully with min 2 persons at the edge of the pallet and set it up at the designated site Ensure that the installation site has the required load carrying capacity 400 kg 12 Important Notes Site Preparation and Commissioning Removing the Back Panel at t
23. t the Cash Tower CINEO 6010 1 2 Adjusting Points for bi optical tower 2 28 Important Notes Site Preparation and Commissioning Removing the Transportation Locks After unwrapping the system remove the transportation locks from the following components see arrows iCash10 iCash15 29 Important Notes Site Preparation and Commissioning Coupon Box gt H D bh H A Ta Lge A Ch FS Wi Ze 30 Important Notes Site Preparation and Commissioning Connecting the System The delivered system is completely configured There are just a few things to do before starting up the BEETLE iSCAN Tower Line 150 A 16A fuse complying with IEC60127 breaking capacity of 1500A must be part of the building installation Start up The power supply system must be equipped with separately guided protective earth conductor PE This kind of electricity system is known as TN S network Do not use PEN conductors Ratings of BEETLE iSCAN Tower Line 150 220 V 240 V 50 60 Hz 2 9A 110 V 120 V 50 60 Hz 3 5A Find the rating of your device on the type label at the back side of the device AN A 16A fuse complying with IEC60127 breaking capacity of 1500A must be part of the building installation 31 Important Notes Site Preparation and Commissioning Caution Check that the set nominal voltage of the appliance corresponds to the local mains voltage Power Connection and LAN
24. tem from the Mains 34 At first shut down the system by the software application Switching off the device is the same procedure like switching on but in reverse order Caution To separate the device completely from power supply unplug the power cable UPS must switched off this too to separate BEETLE iSCAN Tower Line 150 from power completely Important Notes Site Preparation and Commissioning Appendix Further Documentation KR You will find the Hardware User Manual on the Internet http www wincor nixdorf com internet site DE DE Support Downloads POSLotterySystems Manuals BEETLE BEETLE node html The service documentation will be available on the Wincor Nixdorf Intranet only Cleaning Instructions Always turn off the system before cleaning The glass surface of your Touch Screen should be cleaned with a mild abrasive free com mercially available glass cleaning product All pH neutral materials pH 6 to 8 are good for cleaning Cleaners with pH values 9 to 10 are not recommended Cleaning with water and isopropyl alcohol is possible as well Do not use solvents containing acetic acid Use a soft fine meshed cloth to clean the surface Dampen the cloth slightly and then clean the screen Wrong maintenance may cause damages to the screen which are not covered by guarantee or warranty Maintenance and Service When carrying out work on the components and modules that carry an electrical cha
25. th the help of the ramp from the pallet Unlock the door and pull out the carrier completely Remove the two screws fixing the cover WINCOR NIXDORF m Mount the back panel in reverse order 15 Important Notes Site Preparation and Commissioning Removing the Back Panel at the Cash Module iCASH 10 iCASH 15E AN Caution After removing the screws close the device as far as possible to avoid an uncontrolled tilting of the system after removing the fixing screws at the rear side Keep the carrier as close as possible After removing the screws at the rear side close the device at both sides and lock the front door before you tilt the BEETLE iSCAN from the pallet Always remove the device with two persons and with the help of the ramp from the pallet Unlock the front door of the cash module and pull out the carrier completely NOTE OUT 16 Important Notes Site Preparation and Commissioning Remove the two screws fixing the cover in it s position Remove the back panel upwards and remove the fixing screws from the pallet 17 Important Notes Site Preparation and Commissioning Removing the Back Panel at the Cash Module CINEO 6010 AN Caution After removing the screws close the device as far as possible to avoid an uncontrolled tilting of the system after removing the fixing screws at the rear side Keep the carrier as close as possible After removing the scr
Download Pdf Manuals
Related Search