Flight Instrumentation
Contents
1. zero pitch line which is a thin white line stretched across the entire screen Most of the ladder rungs are in 5 degree increments Small horizontal lines below the zero pitch line are in 1 degree increments for precise pitch control during landing approach In the screenshot above right the pitch angle of the aircraft is about 1 degree nose low as shown by the Attitude Reference Index bars crossing the first rung below the zero pitch line In the screenshot below it note the white circle that marks the 90 degree pitch rung This is visible during a loop or hammerhead 90 Pitch Rung Revision Al Horizon HXr User Manual Draft 23 Flight Instrumentation GR T Adjusting Pitch Ladder Offset During straight and level unaccelerated flight at the normal cruise power setting the pitch ladder should be set so that the Attitude Reference Index is aligned with the zero pitch line The object is to set the pitch ladder for the easiest possible instrument scan during cruise 1 Press MORE gt Set Menu gt Primary Flight Display 2 Scroll to Pitch Ladder Offset Adjustments are made in positive or negative 1 degree increments a positive setting will move the Attitude Reference Index up and a negative setting will move it down 3 Adjust it in small increments until the Attitude Reference Index and the zero pitch line are aligned during level normal cruise flight NOTE Pitch Ladder Offset should notbe used to compensate for th2. Maintenance page Terrain Terrain features are presented on the primary flight display as they would appear out the window Mountains rivers lakes valleys and other features appear on the screen and help guide the pilot in low visibility situations In addition to the normal green to brown terrain shading portions of the surrounding terrain that are close to the aircraft s present altitude can be colored yellow 500 1000 feet below the aircraft and red within 500 feet of the aircraft s altitude and higher NOTE Turning terrain warning ON will color all terrain within 1000 feet of present altitude even during landing approach Some passengers may find this to be alarming To turn on red and yellow terrain warning shading on the PFD 1 Press SCREEN gt PFD OPTIONS gt TERRAIN To turn off terrain warning shading and go back to default SV 1 Press SCREEN gt PFD OPTIONS gt SYN VIS Obstacles Towers and other obstacles in the 56 day Navigation Database are displayed on the PFD as either simple lines or chart style graphic tower symbols The same altitude color coding as Terrain applies To choose how obstacles are depicted on the PFD screen 1 Press MORE gt Set Menu gt Primary Flight Display 2 Scroll to Obstacle Style and choose Line or Chart Horizon HXr User Manual Draft Revision Al L AVIONI Artificial Runways Runways can be displayed on the PFD as a black strip with centerline and runway de
3. the brick Sky Pointer Always points toward sky perpendicular to Earth Turn Rate Indicator Place Sky Pointer on green triangle for standard rate turn Vertical Speed Indicator White band is visual digital block on bottom Is actual vertical speed Altimeter Tape with color coded bands for terrain awareness Wind Vector Displays Headwind Tailwind and L R crosswind components Altimeter Setting Traditional barometric pressure setting Height AGL Derived from GPS altitude and terrain database Visible on Synthetic Approach only Flight Path Marker Airplane s path through space in relation to the ground Attitude Indicator Traditional attitude indicator markings uses entire screen as a horizon Airspeed Indicator Airspeed tape with configurable V speeds colored bands and trend indicator 9 2 Horizon HXr User Manual Draft Revision Al GR T Flight Instrumentation 2 2 Attitude Indicator Artificial Horizon The Artificial Horizon is just that a pictorial representation of the earth The blue portion represents the sky the green or brown portion represents the ground The HXr displays a computer generated representation of the view out the window using GPS based technology known as synthetic vision to enhance the artificial horizon and make it more realistic By adding details such as mountain peaks runways and obstacles to the pilot s instrument scan field of view the system adds intuitive situational awareness ev
4. value for most phases of flight but is useful for stall warning and to a limited extent as a means of establishing an approach speed that accounts for the current weight of the airplane WARNING The AOA must be activated in the Primary Flight Display set menu and calibrated before use See HX User Guide Section 9 for more information Ss WARNING The use of this indication is purely at the judgment of the pilot The accuracy of this AOA indexer and its stall warning is affected by EFIS sensor errors and the accuracy of the calibration procedure The EFIS calculation of angle of attack and the approach AOA indexer should not be used as the only stall warning instrument Some indication lag and error will occur when flying through areas of rising and falling air Do not rely on the indexer in turbulent conditions Approach AOA Indexer This indicator appears just to the right of the airspeed tape and shows the angle of attack relative to the optimal for approach When the angle of attack too low the airplane is flying faster than optimal approach speed yellow chevrons pointing up into a yellow circle prompt the pilot to increase back pressure to reduce speed and similarly red chevrons pointing down into a circle prompt the pilot to push forward to increase speed When stall is imminent the word PUSH appears above the AOA indexer The indexer will show a green circle with no chevrons when the angle of attack is in the
5. 1 5 134 amp a Oil Oil EiS EFIS EFS Amp e n THT Oil Oil EIS Psi Temp Volt PUSH SYNC SEL HDG Psi Temp Volt VItl INSET SCREEN SNAP FLTPLAN CDI OBS Split screen heading tape with EGT CHT gauges Split screen HSI presentation No EGT CHT gauges 2 12 Horizon HXr User Manual Draft Revision Al AVIONICS 2 7 Wind Vector amp Crosswind Component The wind vector is located to the right of the altimeter baro setting It is calculated using GPS ground track ground speed and heading and true airspeed data provided by the AHRS It consists of two main parts a vector arrow with velocity and direction and a headwind crosswind component At its simplest it is an arrow with a velocity number next to it The wind blows from tail to head The velocity is given in the speed distance units chosen for the EFIS system In addition to the vector arrow a magnetic compass direction can also be displayed The arrow points from left to right signifying R a crosswind trom the left at 8 knots To turn on the wind vector 1 Press MORE gt Set Menu gt Primary Flight Display 332 8 2 Scroll to Wind Indicator Mode Choose OFF Vector and Digital Speed shown above or Vector and Digital Soeed Direction adds magnetic wind direction to the above display shown at right Headwind Crosswind Component The headwind crosswind component gives headwind H or tailwind T first and left L or right R crossw
6. Centerline course ribbon leading to waypoint balloon on the horizon F R Q 2 lt Z Thal ali al PUSH AJP FLTPLAN CDI OBS MORE INSET SEL ALT Revision Al Horizon HXr User Manual Draft 99
7. GR T Flight Instrumentation 2 1 Primary Flight Display Overview The HXr Primary Flight Display or PFD is a digital representation of the traditional flight instruments such as airspeed altimeter heading and attitude indicator enhanced by features that help ease pilot workload and give a more intuitive feel to the instrument scan The flight instrumentation of HXr was designed to minimize pilot workload by maintaining consistency in layout and design of critical elements for aircraft control Supplemental information such as map and engine data is provided in pilot selectable inset windows that do not rearrange the basic flight instrumentation this allows a pilot to always maintain the same scan even though he or she may need different types of information on the screen as the flight progresses A a split screen PFD view is also available that displays a large PFD next to a detailed moving map and engine instrumentation strip WARNING The magnetometer and pitot static system must be calibrated before the first flight to ensure correct instrument indications on the PFD See Section 9 of the HX User Manual for instructions WARNING A PFD offers much more information and requires a different instrument scan than a traditional 6 pack grouping of analog flight instruments It is imperative that you develop proficiency using the PFD and become accustomed to the different instrument scan needed for a PFD before flying in actual instrument c
8. ays the G meter on the PFD in Auto setting when this negative value is exceeded Turning On the G Meter 1 Press MORE gt Set Menu gt Primary Flight Display 2 Scroll to the G Meter options near the bottom of the screen Select an option on the G Meter Mode setting a Off Does not display Note that even when the G Meter Mode is set to Off all G force data is recorded during data logging b On Displays all the time c On with Min Max Displays all the time with the minimum and maximum Gs experienced during the flight d Auto Comes on if a preset Auto G Meter High or Low Threshold is exceeded This allows it to replace Trim Indicators temporarily until the G limits settle below the threshold See Trim Indicator notation 2 14 Horizon HXr User Manual Draft Revision Al GR T Flight Instrumentation Setting Up the G Meter Enter the maximum positive limit and minimum negative limit of your aircraft in the G Meter Minimum and Maximum settings Set the Caution limits the same way the G meter turns red if the Max Min limits are exceeded and turns yellow if the Caution limits are exceeded Your aircraft designer may have established caution levels or you can choose your own Using the G Meter with Trim Indicators Space on the PFD is limited and the best place for the flap and pitch trim indicators happens to be the same place the G meter resides The G Meter Mode Auto setting will automatically make
9. d The turn coordinator triangles spread out or in as the airspeed increases or decreases To make a standard rate turn align the sky pointer with the green triangle This pilot is performing a half standard rate turn by placing the sky pointer between the neutral marker and the green triangle The turn coordinator can be turned off to declutter the display To turn it on or off 1 Press MORE gt Set Menu gt Primary Flight Display 2 Scroll to Turn Rate Indicator 3 Select ON or OFF as appropriate Revision Al Horizon HXr User Manual Draft 2 5 Flight Instrumentation GR T 2 3 Airspeed Tape The primary function of the airspeed tape is to display indicated airspeed and its associated color bands all of which are fully programmable according to the aircraft design limitations It also has several supplemental sources of information to provide the pilot with an intuitive sense of airspeed change as well as true airspeed and groundspeed True Airspeed gt 143 ro j T S 200 Digital Airspeed Readout gt Speed Distance Trend Arrow Units Groundspeed gt i The instantaneous airspeed readout is contained in the black box with large bold numbers The digits appear to roll by smoothly as speed changes The units of distance speed are displayed below the digital readout True airspeed TAS is displayed in the upper left corner while GPS groundspeed is displayed in the lower left corner as sho
10. e above mean sea level MSL in hundreds of feet or meters Even Terrain thousands are depicted by a solid marker either Clearance a circle triangle or rectangle Five hundred foot a an increments are depicted by a hollow marker The baro setting is displayed in the lower right corner Digital MSL The terrain clearance color band on the edge of Altitude the altimeter tape shows the Off Route Obstacle Clearance Altitude OROCA which provides 1000 foot obstruction clearance in non mountainous terrain areas and 2 000 foot obstruction clearance attitude Bug in designated mountainous areas within the set below the Altimeter United States An altitude below the OROCA is tape range on shown yellow above the OROCA is shown green Revision Al Horizon HXr User Manual Draft a7 2 0 Flight Instrumentation GR T To adjust the barometric pressure setting on the altimeter 1 From any HOME screen press the light blue BARO softkey 2 Turn the right knob to the current altimeter setting GPS Alt t Alternatively press the 29 92 softkey for transition 013 3 Press the knob again to accept the new baro setting or CANCEL to abandon the changes NOTE The difference between the pitot static altitude and GPS derived altitude is displayed in the window behind the right knob while the BARO controls are active Using the Altitude Bug The Altitude Bug has a window located above the altimeter tape and is marked on the altimeter tape
11. e tail down attitude of a taildragger on the ground When you are on the ground in a taildragger the view out the virtual EFIS window should look toward the sky just as it looks out the windshield Pitch ladder offset is ONLY for calibrating straight and level flight It should also never be used to adjust the attitude indication for varying airspeeds or other flight conditions Once it s set for your particular airframe engine propeller combo the Pitch Ladder Offset should not normally be moved Adjusting this for varying flight conditions can be dangerous when those conditions change again potentially leading to spacial disorientation in instrument conditions Paying attention to a consistently placed pitch ladder indication will result in greater understanding of the pitch changes that occur with changing airspeeds power settings and cargo loading Sky Pointer amp Slip Skid Indicator The Sky Pointer is the white triangle in the middle of the bank indicator hash marks This simply points UP at all times If you roll inverted it will point at the sky and thus appear as if it s pointed at your floorboards This is displayed as an aid for unusual attitude recovery and also serves as the bank angle pointer The small rectangular bar that slides under the Sky Pointer is the Slip Skid Indicator thus the modern instructor s command for coordinated turns has become Step on the Brick At the request of some of our aerobatic HXr pilots the t
12. e the form of a magenta course centerline or dual magenta shaded boundaries on each side of the course starting at 200 feet apart and tapering inward as the waypoint gets closer Course ribbons beyond the next waypoint show as white centerlines In the example below the next waypoint is after a right turn COMI Cs ALL STBY E e STBY Active leg of flight 117 50 122 70 10 127 97 plan denoted by i T course ribbon boundary is shown Magenta waypoint balloon marks RIPON the active waypoint The next waypoint in a sequential flight plan is a white balloon This example looks es pink because it is behind the transparent course ribbon boundary 2000 17 29 89 Omi 220 Horizon HXr User Manual Draft Revision Al ESRI To turn course ribbons on and select their form 1 Press MORE gt Set Menu gt Primary Flight Display 2 Scroll to Course Ribbons Select NONE CENTER or BOUNDARIES Course ribbon centerline form This pilot is flying slightly above and to the left of course as indicated by the magenta course ribbon centerline the HSI and the altitude bug marker RIPON 19nm 358 ETE 8m1l3s 1 LUMI 1 2 ALLISTBY STEHY 117 50 122 70 MON 1100 22 27 19 154 Ft 301 110 1 inn Zo 1 Fi a I A E gt ip COMI OL 19 SQL ON PUSH OFF HOLD AD ACTIVE amp Mm STHY O OFF N 1500 n ZME PEET n
13. en in low visibility and instrument conditions Other instruments add motion sensing trend vectors and environmental information to the scan as well providing an intuitive feel for the pilot The total picture offered by the artificial horizon consists of several components working together Attitude Reference Index The Attitude Reference Index is always the in the same position relative to the aircraft The horizon line pitch ladder and sky pointer move in relation to it providing the indications of pitch roll and which way is UP as a a a Attitude Reference Index Bars The traditional attitude bars or wings can be replaced by a nose indicator shown at right This small indicator concisely displays the nose position of the aircraft relative to the horizon To select Nose or Bars wings 1 Access Set Menu gt Primary Flight Display gt Attitude Reference Index Nose 2 Select NOSE or BARS NOTE When ILS CDI crosshairs are displayed on the PFD they replace the Attitude Reference Index The crosshairs are always in the same position as the Attitude Reference Index so they provide an effective replacement Displaying both would unnecessarily clutter the screen Pitch Ladder Offset The Pitch Ladder is a portion of the artificial horizon that depicts the pitch Pitch Ladder angle of the aircraft in relation to the horizon It consists of horizontal lines above and below the neutral
14. ft has flown off course to the right The heading bug and the GPS waypoint bearing marker are both beyond range of the tape so they are hollow and appear to be stuck at the edge of the heading tape The pilot can get back on course by turning left toward the heading bug and GPS waypoint bearing Using the Heading Bug To change the position of the heading bug from any HOME N PUSH SYNC screen turn the left knob The digital position of the heading bug SELHDG INSET SCREEN will display in the window above the left knob and the visual bug indicator rotates around or slides across the heading tape To immediately set the heading bug to the present heading er EJ Ly simply push the left knob to sync it For more information about using the heading bug with the autopilot please refer to the Autopilot section of this manual Moving the heading bug while the autopilot is engaged in Heading Mode will result in an immediate turn to the new heading specified by the bug Split Screen PFD HSI Presentation On the Split Screen PFD pilots can choose between the straight heading tape with EGT CHT graphs or the full HSI presentation on the Split Screen PFD by pressing SCREEN gt PFD Options gt EGT CHT or HSI softkeys This allows the most important information to be displayed in a minimum amount of space 057 y V i 6 fi R 77 178 134 53 52 CHT 324 321 EGT 1431 1403 314 321 1412 1428 7
15. ind second To turn on head crosswind 332 8 component ad OT 8L 1 Press MORE gt Set Menu gt Primary FLight Display 2 Scroll to Digital Head Crosswind Display and turn it ON or OFF NOTE If insufficient data exists for calculation of winds the wind information is not displayed Accurate winds require accurate magnetic heading and airspeed data which are enhanced by performing proper calibration of magnetometer and pitot static systems as detailed in the HXr Installation Manual also the HX User Manual Rev C Section 9 Revision Al Horizon HXr User Manual Draft 2 18 Flight Instrumentation GR T 2 8 G Meter The G meter measures the G loading of the airplane based on forces measured by the accelerometers inside the AHRS It is displayed to the right of the airspeed tape on the Primary Flight Display G Meter Settings Press MORE gt Set Menu gt Primary Flight Display to access G Meter settings G Meter Mode Choose if or how to display it on the Primary Flight Display G Meter Maximum Sets the maximum positive G loading on the scale G Meter Minimum Sets the minimum negative G loading on the scale G Meter Caution Max Positive G load caution threshold Turns yellow beyond this value G Meter Caution Min Negative G load caution threshold Turns yellow beyond this value Auto G Meter High Threshold Displays the G meter on the PFD in Auto setting when this positive G value is exceeded Auto G Meter Low Threshold Displ
16. itself by a magenta rectangle with a notch The altitude bug serves two functions e The commanded altitude for the autopilot to Altitude Preselect climb descend to and hold Window e A reminder for a cruise altitude or any other altitude the pilot wishes to remember To set the altitude bug from any HOME page 1 Turn the Right Knob to enter the desired altitude into the Altitude Preselect Window Altitude Bug Marker 2 Press the knob to set 3 If an autopilot with vertical navigation capability is installed and engaged the system will then display a message to verify the speed or rate of the climb or descent desired to fly to the set altitude See Autopilot section of this manual for more information on coupled climbs amp descents Altitude Intercept Arc Map Screen The Altitude Intercept Arc appears as a variable green arc on the map screen It is a visual depiction of the place the aircraft will be when it f Trara intercepts the altitude entered into the altitude preselect window It is Ay calculated using the current rate of climb or descent and groundspeed esfitve AZOLE During a climb or descent adjust the rate of altitude change to place the arc over the place you want to be when you get to your selected altitude This can be very useful in a cruise descent toward your destination if you set the altitude bug to pattern altitude or your next IFR altitude It can also be useful for planning climbs nea
17. ly even if the visual indicator is maxed out 2 6 Heading Indicator The HXr magnetic heading indicator is presented in a Horizontal Situation Indicator HSI format on the PFD screen and an arc format on the Map screen This section of the manual covers the basic heading functions of the HSI Detailed information on how to use the bearing pointers and navigation functions of the HSI are found in the Navigation section of this manual Using the Heading Indicator The heading indicator gets its magnetic information from the magnetometer and is corrected with internal calculations by the AHRS After the magnetometer is calibrated there is no need or provision for manually adjusting it it is all done automatically during AHRS boot up and alignment This eliminates in flight precession and forgetting to set it before takeoff common issues with vacuum gyro instruments Revision Al Horizon HXr User Manual Draft g9 Flight Instrumentation G RT AVIONICS Components of the HSI Horizontal Situation Indicator The HSI overlays GPS and VOR LOC courses onto a heading indicator It functions as a standard HSI Vertical Compass Presentation Presents all 360 with your aircraft in the center Automatically sets correct magnetic heading before flight using magnetometer information Magnetic Heading The present magnetic heading is displayed in large numbers at the top Heading Bug Small rectangle either white or dark magenta used as a reminder and t
18. n The heading tape covers a 70 span and is presented above the engine strip on the Split PFD screen It displays four parameters with the following white or magenta symbols V Magnetic Heading H V GPS Ground Track T AA Bearing or course to current GPS waypoint CIL Heading Bug On both the Primary Flight Display and Moving Map Setup pages there is a setting for Up Reference on the very top of the page This can be either Heading or Track Most pilots prefer their PFD heading indicator to be Heading Up so they can accurately follow ATC vectors Track Up is usually preferred for the moving map screen The parameter that is set as the Up Reference is stationary at the top or center of the heading presentation and labeled as shown below PFD Tape Heading UP Bearing to GPS Ground Heading waypoint Heading Track Bug Map Arc Track UP The bearing and track symbols fit inside each other so they create a nice visual effect when the aircraft IS ON course The symbols are magenta when they are selected for navigation for example if the autopilot is in heading mode the heading bug and heading triangle will be magenta and the track and bearing symbols will be white Revision Al Horizon HXr User Manual Draft aii Flight Instrumentation GR T In the tape and arc views if one of the symbols runs off the edge of the screen it becomes hollow and stays on the side of the screen closest to it as shown below This aircra
19. o control the lateral autopilot in heading mode Controlled by the Left Knob Track Pointer Small magenta diamond that points in the direction of the current ground track Bearing Pointers Independent of the course pointer and always point at their corresponding nav source BRG 1 has a solid head and single tail shaft BRG 2 has a split head and double tail shaft Course Selection Needle Represents active nav course The center segment of the GPS or VOR LOC course needle or Course Deviation Bar moves along a CDI scale when in range To From Indicator Green triangle appears when tracking a VOR radial TO points toward Course Selection Pointer head From points toward Course Selection Pointer tail Magnetic Heading GPS Ground Track Pointer Heading Bug Bearing Pointer Head BRG 1 002 Course Selection Needle Head BEBE Rae eh 0 am Hr E p Course Deviation Bar F 30 To From _ Indicator Course Selection Course Deviation Needle Tail Indicator CDI Scale Pa UVa EE n i FLTPLAN CDI OBS 210 Horizon HXr User Manual Draft Revision Al Bearing Pointer Tail BRG 1 GRT AVIONICS Flight Instrumentation Arc and Tape Heading Presentations While the 360 HSI presentation is straightforward the heading tape and arc views have some unique features The tape view is present on the PFD Split Screen view if the EGT CHT graphs are shown The 160 arc or 360 non HSI view can be shown on the map scree
20. onditions Dual instruction from a CFI experienced with EFIS systems is highly recommended The basic PFD Home screen consists of the primary flight instruments e Full width Artificial Horizon with 30 mile Synthetic Vision e Altimeter Tape with trend marker and sensitive baro setting e Airspeed Tape with programmable V speeds color strips and trend marker e 360 Heading Indicator with HSI and heading bug e Vertical Speed Indicator with programmable range visual needle and digital readout e Pitch Ladder Bank Angle indictors Turn Coordinator and Slip Skid indicator Secondary information on the PFD covered in this section includes e Wind vectors true airspeed GPS groundspeed amp waypoint information e Sky Pointer and Flight Path Marker to add awareness of aircraft position and motion in space e Synthetic vision terrain course ribbons and waypoint markers to make enroute navigation easy e G Meter programmable for individual aircraft limits e Trim and flap indicators optional trim flap position sensor required Revision Al Horizon HXr User Manual Draft ax AVIONICS Slip Skid Sky Turn Rate 3 Brick Pointer Indicator are Altimeter Indicator ae UU ee ee i hii iy Le F 30 11 mA Airspeed Attitude Flight Path Height AGL Altimeter Wind Indicator Indicator Marker Setting Slip Skid Brick Slides under Sky Pointer triangle to represent coordination Replaces traditional skid ball Step on
21. optimal range for approach The approach AOA indexer will not appear at low angles of attack Barber Pole Stall Speed Indicator A vertical red black bar is displayed on the bottom half of the airspeed tape The top of this bar corresponds to the stall speed at the current G loading and is based on the stall speed entry made in the EFIS and the normal acceleration G s sensed by the AHRS GR T Flight Instrumentation Pitch Limit Indicator When enabled on the PFD settings page the pitch limit indicator appears on the PFD screen when the angle of attack is less than 8 degrees from stall and goes away when the angle of attack more than 9 degrees from stall It resembles a red pair of antlers and is shown in the screenshot below The indicator moves downward toward the nose or bars pitch indicator as the angle of attack increases Stall will occur approximately when this indicator is on the nose or bar pitch indicator This indicator is limited to 30 degrees pitch to prevent chasing a pitch limit that could temporarily be at a very high pitch angle due to high airplane speed The pitch limit indicator was originally created to give pilots a maximum pitch angle reference when performing a windshear escape maneuver While this may be of little use for the typical experimental aircraft pilot it could be useful for assisting with terrain avoidance in a low airspeed situation In that case the pilot can use the pitch limit indicator as an ap
22. proximate reference of a pitch angle that will result in stall AOA Settings To turn on or turn off AOA functions 1 Press MORE gt Set Menu gt Primary Flight Display 2 Scroll to AOA Select ON or OFF This will activate more settings just below the AOA setting 3 Turn on the Pitch Limit Indicator if desired WARNING AOA must be calibrated before use See Section 9 HX User Manual Revision Al Horizon HXr User Manual Draft O17 Flight Instrumentation GR T 2 11 Synthetic Vision Features amp Settings Synthetic vision SV is standard on HXr It displays a 30 mile out the window view on the PFD of terrain runways obstacles and traffic It also provides a top down terrain view on the Map pages GRT factory technicians load the synthetic vision terrain database appropriate for the area of the world in which the EFIS system will be used prior to shipment NOTE Synthetic vision is dependent upon GPS signal for proper depiction relative to the internal terrain database NOTE The synthetic vision terrain database does NOT need to be periodically updated and is not downloadable from the GRT website Contact GRT for support if you encounter any problems with the synthetic vision database or if you are flying in an area of the world that is different from the database loaded in your system To access synthetic vision database status for troubleshooting press MORE gt Set Menu gt Display Unit Maintenance gt Database
23. r high terrain The more stable the descent or climb the more stable the arc will be It shrinks as you get closer to the altitude intercept point Horizon HXr User Manual Draft Revision Al GR T Flight Instrumentation Altitude Deviation Alerts An alert can be set to flash on the EFIS when the altitude specified in the Altitude Bug Window is exceeded by a certain amount To set an Altitude Alert 1 Press MORE gt Set Menu gt Primary Flight Display 2 Scroll to Altitude Alerting and turn it ON 3 Highlight Max Altitude Deviation Set the altitude deviation alert threshold typically 200 feet 2 5 Vertical Speed Indicator The vertical speed indicator VSI is along the left side of the altimeter VSI The tape is white and radiates upward or downward from the neutral digital mark as the aircraft climbs and descends It shows vertical speed in feet value or meters per minute The vertical speed is also presented digitally at the bottom of the scale when descending and at the top of the scale when climbing The VSI tape s upper limit can be programmed to fit the climb performance capability of the aircraft for a more precise visual representation VSI tape To customize the VSI 1 Press MORE gt Set Menu gt Primary Flight Display 2 Scroll to Max Indicator Vertical Speed Choose the upper limit of the VSI scale most appropriate for the aircraft s climb performance The actual rate of climb will still be displayed numerical
24. raditional ball type slip skid indicator is now available as a choice on the HXr under the Set Menu gt Primary Flight Display gt Slip indicator setting When ball is selected the bar disappears and the electronic ball is prominently displayed above the heading indicator Slip indicator ball 9 4 Horizon HXr User Manual Draft Revision Al GR T Flight Instrumentation Flight Path Marker The flight path marker shows where the aircraft will go if all conditions of motion and wind stay the same Shown as a circle with three spikes it is a projection of the aircraft s flight path It combines many data factors including attitude airspeed and wind vectors calculated from GPS ground track ground speed airspeed and magnetic M heading The flight path marker will appear to float about the display as the aircraft pitches and rolls This movement is most evident in strong crosswind or unusual attitudes For example during a properly flown crabbed crosswind approach the heading nose will point to the upwind side but the flight path marker center of mass will be superimposed on the virtual runway because that is where the airplane is going at that particular instant in time 2 3 Turn Coordinator The turn coordinator is depicted at the top of the pitch ladder and below the heading window as a pair of inverted green triangles The HXr calculates the angle of bank required to make a standard rate turn at the current airspee
25. raffic on the PFD ai y i oe 33 1 Press MORE gt Set Menu gt Primary Flight Display amp a J 6 2 Scroll to Traffic In View and select ON a j 24 Screenshot at right illustrates grid overlay and traffic amp target shown on both the synthetic vision see red oy i 13 a nd lt arrow and in the Traffic Alert Inset PLAN CDI OBS BARO MORE INSET Revision Al Horizon HXr User Manual Draft 9 19 AVIONICS Waypoint Balloons Waypoint balloons are markers that highlight the next GPS waypoints in the flight plan on the PFD They have a tether that points directly downward to the waypoint and are raised and lowered with the altitude bug They are visible f s3 beyond the 30 mile horizon line in that case they do not have a tether as shown to the right In an enroute crosswind situation keep the flight path marker on the waypoint balloon to fly directly to the waypoint The active waypoint balloon is magenta Subsequent waypoints in the flight plan are white Waypoint Balloon over the horizon To turn on waypoint balloons 1 Press MORE gt Set Menu gt Primary Flight Display 2 Scroll to Waypoint Balloons and select ON or OFF Course Ribbons Course ribbons are a form of enroute Highway In The Sky They connect waypoint balloons and draw a path in the sky that corresponds to the active flight plan leg essentially a 3D version of the course lines drawn on the map screen Course ribbons can tak
26. signation number This is extremely useful for spotting runways from the air and for flying into airports with multiple runways NOTE Turf runways will be depicted as black strips even though they are not paved Private runways can be added to the database by E adding them as User Waypoints See Section 3 Adding User Waypoints To display runways on synthetic vision 1 Press MORE gt Set Menu gt Primary Flight Display 2 Scroll to Artificial Runways and select ON Grid Overlay The HXr can lay a grid onto the terrain of the PFD creating an enhanced sense of depth height and direction to the synthetic vision The grid is aligned with the cardinal true directions N S E and W It fades with height and distance to create an illusion of space The squares are 12 arc seconds apart or about 1 215 feet and follow the shape of the terrain To display the grid on synthetic vision 1 Press MORE gt Set Menu gt Primary Flight 3700 21 46 26 Display 3700 14626 2 Scroll to Synthetic Vision Grid Overlay and select ON s a b a sy Traffic s Traffic targets picked up by ADS B or TIS can be displayed in space on the PFD to mimic the view 1k out the windshield The traffic vector line points from a the diamond shaped target in the direction of motion 1 h 1500 See Traffic Alert inset or map for target altitude a JL 5555 17 relative to your position in hundreds of feet E 29 89 seam 355 To display t
27. the G meter appear in place of the trim indicator when the Auto G Meter Max and Min Threshold limits are exceeded in flight G Meter Data Logging G force data is recorded with all of the other AHRS data during a demo recording For instructions on how to record a permanent record of your G readings see the Flight Data Recording Feature of the Week on the GRT website for automatic recording of flight data G Meter Limitations The G meter has the same limitations as the AHRS 10 G of acceleration 2 9 Flap and Trim Indicators If the aircraft is equipped with electronic flap and trim position sensors they can be wired directly to the HXr analogs and the indication programmed to appear on the screen eliminating the need for external LED indicator lights See HXr Installation Manual for information on wiring and setup The indicators appear to the immediate lower right of the airspeed indicator as shown below To change the direction of the Pitch Trim indication UP on top or DOWN on top 1 Press MORE gt Set Menu gt General Setup 120 165 110 GS 2 Scroll to Elevator Trim Orientation and choose Down trim D at the top or UP trim U at the top Revision Al Horizon HXr User Manual Draft 9 15 2 10 Angle of Attack Indicator AOA Angle of Attack is calculated by the EFIS by combining a variety of sensor data It may be used to drive two different indicators on the PFD screen Angle of attack is not of much
28. wn below Trend Arrow The trend arrow points to the predicted speed of the aircraft in 5 seconds at the current rate of acceleration V Speed Reference Markers The airspeed tape also features three programmable V speed reference markers that appear as magenta triangles with letters X Y amp G these stand for for Vx Vy and Ve best glide Vx airspeed marker alongside the green and white color bands pa Horizon HXr User Manual Draft Revision Al GR T Flight Instrumentation Colored Airspeed Bands The colored band on the airspeed tape follows the standard airspeed color scheme The digital airspeed value turns yellow or red when it is within the yellow or red ranges for additional emphasis Zero to Vs full flap stall speed Airspeed values too low to register on the EFIS will appear as a red dash in the digital readout window Option Red or clear Stall speed Vso to maximum structural cruise speed Vno Maximum structural cruise speed Vno to never exceed speed Vne Never exceed Vne and beyond Customizing the Airspeed Tape For Your Aircraft The airspeed indicator settings are programmed in SET Menu gt General Setup gt Primary Flight Display They should be programmed before the first flight according to the design limitations of the aircraft and can be fine tuned during flight testing to match the individual aircraft s flight characteristics 2 4 Altimeter Tape The Altimeter Tape displays altitud
Download Pdf Manuals
Related Search