XR 330 SPOT - PR Lighting
Contents
1. d aAA li MC ei AL m ws INPUT OUTPUT INPUT OUTPUT INPUT DMX TERMINATOR OPERATION MENU First Menu Secondary Menu Third Menu Fourth Menu XXX Dyes XXX 1 449 Reset Are You Sure DMX Mode Snai Default Standard Short By Control Channel Lamp Control By Power On By DMX Present When DMX is Lost Normal Time out Config Settings Loss of DMX When DMX is Lost Hold Last value Fan Operate Mode Fan Operate Mode man Hot Environment Factory Settings Fixture Type Press button WARNING Never change the DOWN UP ENTER at the same fixture type or the fixture will be time to enter the sub menu damaged 7 23 Option Settings Color Positions Color Positions STEPPED Color Positions LINEAR F Gobo Positions F Gobo Positions STEPPED F Gobo Positions LINEAR Pan DMX Invert Pan DMX Invert OFF Pan DMX Invert ON Tilt DMX Invert Tilt DMX Invert OFF Tilt DMX Invert ON Pan Tilt Swap Pan Tilt Swap OFF Pan Tilt Swap ON Dimmer Invert Dimmer Invert OFF Dimmer Invert ON Tris Invert Tris Invert OFF Tris Invert ON Zoom Invert Zoom Invert OFF Zoom Invert ON CMY Invert CMY Invert OFF CMY Invert O2. R prism In out Salt mon R Prism Rotate AN Frost Frost Focus Focus XXX Zoom OU Pan Coarse k i Pan Fine Pan Fine XXX Tilt Coarse Tilt Coarse XXX ee Tilt Fine Tilt Fine XXX M Speed M Speed XXX 000 255 DelayXX Seconds Delay 0 258 100min Link To Step Link To Step XXX 1 28 Shutter ANE Dimmer XXX Colour n XXX is Iris XXX Fixed Gobo e R Gobo Wheel R Gobo Wheel R Gobo Rotate n ne R Prism Wheel SO bi ji R Prism Rotate Q pism Wheel Scene XX User Memory 2 1 28 Focus oe XXX Zoom OU Pan Coarse get m Pan Fine oe y Tilt Coarse Tilt Coarse XXX Tilt Fine Se M Speed M Speed XXX 000 255 DelayXX Seconds Delay 0 25s 100min Link To Step Link To Step XXX 1 28 Shutter Shutter XXX Static Scene Fi e stad Colour Colour XXX 11 23 e Iris Iris XXX Fixed Gobo an R GoboWheel e a vnes R Gobo Rotate n Rotate R Prism Wheel Coote R Prism Rotate on Focus Ven Z Zoom oom XXX Pan Coarse pwe parse Pan Fine E Tilt Coarse V a Tilt Fine ok M Speed M Speed XXX 000 255 Reset User 1 Reset User lt Unlock gt 2 3 amp Memory 1 Has Memory 1 A press Been Reset UP DOWN ENTER at the same time Reset User 2 Init User Memory Reset User ME 226 Memory 2 Has Memory 2 UP DOWN ENTER Been Reset at the same time Reset Static Scn Reset MEL 238 Static Scene Has Static Scene UP DOWNENTER Been Reset at the same time ERROR MESSAGES In
3. XR 330 SPOT PR 2350 This product manual contains important information about the safe installation and use of this projector Please read and follow these instructions carefully and keep this manual in a safe place for future reference PR LIGHTING LTD http www pr lighting com 1 23 SAFE USAGE OF THE PROJECTOR 3 INSTALLING THE PROJECTOR 4 FITTING THE LAMP 4 POWER SUPPLY MAINS 5 CONTROL CONNECTIONS 5 DMX TERMINATOR 6 SETUP OPTIONS PROJECTOR CONFIGURATION 6 TO SET THE DMX START ADDRESS 6 STAND ALONE MODE 7 MASTER SLAVE MODES 7 OPERATION MENU 7 ERROR MESSAGE 10 REPLACING GOBOS 11 DMX PROTOCOL 12 MAINTENANCE 15 LUBRICATION 15 KEEPING THE PROJECTOR CLEAN 15 TROUBLESHOOTING 15 TECHNICAL DATA 16 ELECTRICAL DIAGRAM 19 COMPONENT ORDER CODES 20 Please note that as part of our ongoing commitment to continuous product development specifications are subject to change without notice Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the course of product improvement The publishers cannot be held responsible for the accuracy of the information herein or any consequence arising from them Every unit is tested completely and packed properly by the manufacturer Please make sure the packing and or the unit are in good condition before installation and use Should there be any damage caused by transportation consult your dealer and do not use the unit Any damage caused
4. NET WEIGHT 22Kg Gross Weight in Flight Case 76Kg inFlight Case 2pcs flight case with accessories supplied 31 Kg inCarton 1pes carton with accessories supplied 19 23 SIZES iS Sel LIGHT OUT 42 Lux 3 8 Lux 7m 6m 4m 2m Om 2m 4m 6m DISTANCE m 0 908 227 101 57 36 25 0 74063 18516 8229 4629 2963 2057 5m 3m 1m 1m 3m 5m 7m Om 5m 10m 15m 20m 25m 30m DIAMETER m 0 60 34 068 1 02 136 1 70 2 04 DIAMETER m 0 3 59 7 18 10 76 614 35 17 94 21 53 20 23 Ma m3 M Ms mi ma m3 11 162 13 14 18 5 126 Mi mas Colour Gan Fel Menn obk 1 amp 2 ie Rota Gobo Gobo Fon Fid Gobo Veel Fo Loom Zoam 2 Prim Heec Pim Rotation Fat Driver Board3 Driver Board 1 Driver Board 2 p Ucar HD HALL21 HALL22 HALL23 Gobo Rata Fied Cobo Wheel Display Board XY Driver Board 0 li Switch KE an
5. Switching pow la z Electronic Ballast Power Interface Temperature Switch Housing 21 23 E FE s ki TETE Ta Ey PRIS sida Damn Py Electrical Diagram Component Order Code NAME PART NO QUANTITY REMARK Pan Motor 030040233 1 Tilt Motor 030040233 1 Dimmer Strobe Motor 030040213 2 CYM Motor 030040228 3 Rotating Gobo Wheel Motor 030040231 1 Fixed Gobo Wheel Motor 030040221 1 Color Wheel Motor 030040221 1 Iris Motor 030040230 l Rotator Motor 030040221 1 FOCUS MOTOR 030040232 l FROST MOTOR 030040221 l ZOOM MOTOR 030040215 2 Prism Rotation Motor 030040224 1 Prism Move in Motor 030040221 1 Fan 030060086 2 At Rear side ofthe lamp Turbo Fan 030060064 l Lamp Cooling Fan 030060088 2 In the middle of Head fan 030060089 2 Base Lamp Ballast 040070115 l Lamp 100070031 l Rotating Gobo Wheel Accessory 120110615 1 Color Wheel Accessory 120110609 l Fixed Gobo Wheel Accessory 120110616 1 Power Switch 192010171 1 LCD Master Board 230020678 1 6 channel driver board1 230020680 1 6 channel driver board2 230020681 1 6 channel driver board3 230020682 1 XY Driver Board 230060274 1 Fuse 270041079 1 Tilt Belt 290151244 l Zooming Belt 290151383 2 CYM Belt 290151382 3 Prism Wheel Move in Belt 290151384 1 Gobo Rotation be
6. The connections are illustrated below DMX TERMINATOR CONNECTION Connect a 120 OHM resistor 3 across pins 2 and 3 in an XLR plug 1200 and insert into the DMX out socket on the last unit in the chain BIN 2S ily SETUP OPTIONS PROJECTOR CONFIGURATION DMX o W DMX PR 2350 XR 330 Spot Projector configuration can be set conveniently via push button and LCD display Launch the projector and press button ENTERI for more than 5 seconds to unlock the panel the LCD will show the function menu of the projector each main menu has its submenus and each submenu has a specific function For details please see the OPERATION MENU section Press button UB or DOWN if you want to browse through the various Setup Options Press button ENTER to save your settings or enter the submenu Press button UB or DOWN to change values plus or minus Press button FUNG it will return to the upper menu If button FUNG not pressed the default will show display status automatically TO SET THE DMX START ADDRESS Each XR 330 Spot must be given a DMX start address so that the correct projector responds to the correct control signals This DMX start address is the channel number from which the projector starts to listen to the digital control information being sent out from the controller The XR 330 Spot has 3 DMX modes There are standard mode short mode and extended
7. from power loosen the four fastfit screws of the side cover like figure 1 pull out the rotators by finger as figure 2 figure 2 rotator figure 1 DMX PROTOCOL 13 23 Short Standard Extended FUNCTION DESCRIPTION mode mode Mode 2 Dimming 004 255 Linear dimming 0 100 000 255 Dimmer in 16 bit C 000 016 017 035 Yellow Magenta Red 036 054 CYM Macro yan i 4 KES en n ei Fen 5 000 255 Yellow linear 0 100 8 Yellow in 16 Bit 000 255 Yellow in 16 Bit a pa en 10 Magentain16Bit 000255 Magentain 16 Bit 049 056 000 255 Cyan linear 0 100 Cyan in 16 Bit 000 255 Cyan 16Bit 1 2 3 4 5 7 10 11 7 z Iris Fine Iris in 16 Bit 14 23 000 255 Magenta linear 0 100 000 008 009 016 017 024 025 032 033 040 041 048 057 064 Color Wheel a 2 3 9 10 14 Iris Macro 000 010 011 072 073 136 137 198 199 214 215 222 223 230 Fixed Gobo Wheel 147 165 Reverse Rotation anti clockwise From slow to kn Shakeo Gobo1 O O 15 23 000 128 Gobo Indexing 0 540 f 129 188 Rotation Clockwise From slow to Fast 12 13 17 Gobo Rotation 189 195 196 255 Rotation Anti Clockwise From slow to Fast 13 15 19 Three Facet Prism 000 128 Prism Indexing 129 191 Rotation Clockwise from slow to fast 14 16 20 Prism Rotation 193 255 Rotation Anti Clockwise from slow to fast 15 000 255 Linea
8. the course of launch Projector examines automatically whether there are errors and if there are it will display information as follows Sensor Err S1 M1 Sensor Err S1 M2 Sensor Err S1 M3 Sensor Err S1 M4 Sensor Err S2 M1 Sensor Err S2 M2 Sensor Err S2 M3 Sensor Err S3 M1 Sensor Err S3 M2 Sensor Err S3 M4 Color wheel 1 drive board motor 1 error CYM Cyan 1 drive board motor 2 error CYM yellow 1 drive board motor 3 error CYM Magenta 1 drive board motor 4 error Rotating Gobo wheel 2 drive board motor 1 error Gobo rotation 2 drive board motor 2 error Fixed Gobo Wheel 2 drive board motor 3 error Focus 3 drive board motor 1 error Zooml 3 drive board motor 2 error Prism 3 drive board motor 4 error 12 23 Over Temp Error Temp Sense Error Head Fan 1 Fail Lamp Fan error Head Fan 2 Fail Head Fanl error Head Fan 3 Fail Head Fan2 error Head Fan 4 Fail CYM Fan error Head Fan 5 Fail Fixed gobo wheel fan error Pan Encoder Err Tilt Encoder Err Pan Enc T Out Pan Auto Position Overtime Tilt Enc T Out Tilt Auto Position Overtime Pan Sensor Error Tilt Sensor Error Pan Over Temp Pan Driver Fault Tilt Over Temp Tilt Driver Fault Pan Enc Rev Err Pan Encoder Reverse Wiring Error Tilt Enc Rev Err Tilt Encoder Reverse Wiring Error Replacement of rotating gobos rotating gobo wheel disconnect
9. N Defaults Defaults OFF Defaults Restore Defaults Display Options Display Mode Display On Always Display OffAfter Delay Display Invert Display Invert OFF Display Invert ON Display Dimming Disp Dim Level Min Disp Dim Level l Disp Dim Level 2 Disp Dim Level 3 Disp Dim Level 4 Disp Dim Level 5 Disp Dim Level 6 Disp Dim Level 7 Disp Dim Level 8 Disp Dim Level 9 Disp Dim Level Full 8 23 Display Contrast Display Contrast XX 1 21 default 11 kab H s Lamp Hours Reset Lamp Hours p XX Are You Sure UP DOWN i Total Hours F Hi ixture Hours Xx A Display Board Display Bi isplay Board xXx Driver Board 1 Driver B 1 ver Board XXC Driver Board 2 Dri ver Board 2 XXC Temperature Driver Board 3 ver Board 3 Driver B 3 ver Board XXC Pan and Tilt P Tilt men XXC Head Sensor H ead Sensor XXC A Display Board Display Board XXX Driver Board 1 Driver Board 1 XXX Information Driver Board 2 Software Version Driver Board 2 XXX Driver Board 3 Driver Board 3 XXX Pan and Tilt Pan and Tilt XXX DMX Channel View DMX Val iew lues 1 Electronic SN Electronic SN 2k 2g 2s ak ok ak ok k k kkk RDM Device Label RDM Device Label Wiring Normal Pan Encoder Pan Err 0 Count 0 Wiring Normal Tilt Encoder Tilt Err 0 Count 0 X Ove
10. Warning Please run the safety cord Safety Cord Panel Digital Control through two holes for safety 148 5 Take 2 clamps and the safety cord out from the package and mount 2 clamps on the underside of fixture with 2 retainers attached to each clamp Hang the fixture on the structure and fasten the screws attached to each clamp See the WARNING on the underside of the base as shown above To pass the SAFETY CORD through the HOLES for safety Always ensure that the projector is firmly anchored to avoid vibration and slipping whilst functioning Always ensure that the structure that you are going to mount the projector to is secure and strong enough to support the weight of a XR 330 Spot WARNING 1 The projector MUST be lifted or carried by the HANDLES instead of clamps 2 For safety the safety cord should afford 10 times the Projector s weight FITTING THE LAMP Lock the yoke before fitting replacing adjusting the lam just as Shown by Figure 1 after Opening the cover at the rear of the projector by loosening 8fastfit screws at both sides of the head For lamp adjustment please see the figure2 The removal of a lamp is showed by the figure3 Please tighten the power cord for the lamp before the installation Installation and removal are in reverse orders Note don t touch the bulb of the new lamp with bare hands so as not to impair the beam output Do not damage t
11. by improper use will not be assumed by the manufacturer and or dealer ACCESSORIES These items are packed together with the projector Name Quantity Unit Remark G clamps 2 Pcs XLR connector 1 Set Without cable Power Con 1 Set With cable Safety cord 1 Pc User s manual 1 Pc Q clamps 2 Pcs Optional 2 23 SAFE USAGE OF THE PROJECTOR When unpacking and before disposing of the carton check there is no transportation damage before using the projector Should there be any damage caused by transportation consult your dealer and do not use the apparatus The projector is for indoor use only IP20 Use only in dry locations Keep this device away from rain and moisture excessive heat humidity and dust Do not allow contact with water or any other liquids The projector is not designed or intended to be mounted directly on to inflammable surfaces W The projector is only intended for installation operation and maintenance by qualified personnel The projector must be installed in a location with adequate ventilation at least 50cm from adjacent wall surfaces Be sure that no ventilation slots are blocked Do not project the beam onto inflammable surfaces minimum distance is 3m Avoid direct exposure to the light from the lamp The light is harmful to the eye Do not attempt to dismantle and or modify the projector in any way Electrical connection must only be carried out by qualified person
12. ean It is recommended that the fans should be cleaned every 15 days The lens and dichroic colour filters should also be regularly cleaned to maintain an optimum light output Do NOT use any type of solvent containing chemical elements on dichroic colour filters Cleaning frequency depends on the environment in which the fixture operates A soft cloth and typical glass cleaning products should be used in cleaning It is recommended to clean the external optics at least once every 20 days and clean the internal optics at least once every 30 60 days Do not use any organic solvent e g alcohol to clean the reflector mirror dichroic colour filters or housing of the apparatus TROUBLESHOOTING PROBLEM ACTION tt ens gt Check the fuse on the power socket The projector doesn t switch on gt Check the lamp The lamp is on but the projector doesn t respond gt Make sure that the fixture s start address is right to the controller gt Replace or repair the XLR signal cable The projector functions intermittently gt Make sure the fan is working well or fans and their shields are not blocked a Men gt Make sure the lamp is within its lifespan e din Loy Wenines gt Remove dust or grease from the lenses The project image appears to have a halo gt Carefilly clean the lamp optical lenses and other components Heavily Berediye Baan gt Checkif lensare in good condition not cracked gt Clean dust or grease o
13. hat none of the pins touch the metallic body of the plug or each other XLR plugs and sockets mustn t be connected in any way other than mentioned in the above figure The XR 330 Spot accepts digital control signals in protocol DMX512 1990 Connect the controller s DMX output to the first fixture s DMX input and connect the first fixture s DMX output to the second fixture s DMX input and connect the rest fixtures in the same way Eventually connect the last fixture s DMX output to a DMX terminator as shown in the figure below DMX IN DMX OUT DMX IN DMX OUT TO CONTROLLER TERMINATER 5 23 DMX TERMINATOR In the Controller mode at the last fixture in the chain the DMX output has to be connected with a DMX terminator This prevents electrical noise from disturbing and corrupting the DMX control signals The DMX terminator is simply an XLR connector with a 1200 ohm resistor connected across pins 2 and 3 which is then plugged into the output socket on the last projector in the chain
14. he sticking out of the lamp Important Always read Instructions for use enclosed with the lamp Figure 1 8pcs of fastfit screws oo Figure2 Lamp adjustment loosen the two screws and lift the fan Using cross serewdriver to adjust the two screws for the adjustment the lamp s position and gently and take the lamp out POWER SUPPLY MAINS Connect the power cord as follows L live brown E earth yellow green N neutral blue Before connection with mains power make sure that the voltage and frequency marked on the rating plate of the projector match what are supplied It is recommended that each projector be supplied separately so that they may be individually switched on and off IMPORTANT It is essential that each projector is correctly earthed yellow green twin wire and the electrical installation conforms to all relevant standards CONTROL CONNECTION DMX OUT DMX IN DMX 512 1 ap mi ka vi O QO 3 3 DMX OUT DMX IN 5 PIN 5 ak SO L 5 Co 4 1 0 0 9 4 3 Connection between controller and projector and between one projector and another must be made with a twin screened cable with each wire having at least a 0 5mm in diameter Connection to and from the projector is via cannon 5 pin which are included with the projector or 5 pin XLR plugs and sockets The XLR s are connected as shown in the figure above Note care should be taken to ensure t
15. lt 290151260 1 Pan Belt 290151223 l Prism Wheel Rotation Belt 290151385 1 Focusing Belt 290151383 2 22123 PR LIGHTING LTD 1582 Xingye Avenue Nancun Panyu Guangzhou 511442 China TEL 86 20 3995 2888 FAX 86 20 3995 2330 P N 320020212 Version 20140108 Preliminary 23 23
16. mode For example standard mode has 25channels so set the No 1 projector s address 001 No 2 projector s address 026 No 3 projector s address 051 and so on Launch the projector Press button ENTERI more than 5 seconds to unlock panel Press button ENTER to display DMX address Press button UB and DOWN you can set the address Press button ENTER to confirm after powered on next time the default will be last value saved Press button FUNG it will return to the upper menu 6 23 STAND ALONE MODE Operate the projector without connecting a controller enable the master mode in the operation panel the projector will run in Stand Alone mode automatically MASTER SLAVE MODE Without using a controller many projectors can run synchronously in the Master Slave mode by linking them with each other Connect the controller s output to the first fixture s input and connect the first fixture s output to the second fixture s input and connect the rest fixtures in the same way Eventually connect the last fixture s output toa DMX terminator as shown in the figure below Then the first one is the master with setting options as master mode enabled and others are slaves Start Address for all slaves is 001 The Master can run at any mode for the Master and Slaves run at the corresponding mode compared to the Master After powered the group will run at Master Slave Mode SLAVE
17. n the lens 17 23 TECHNICAL DATA VOLTAGES 100V 240V AC 50 60Hz POWER CONSUMPTION 450W 220V LAMP OSRAM SIRIUS HRI 330W XL Colour Temperature 7500K Manufacturers Rated Lamp Life 1500hours COLOURS CMY linear color mixing system with Marco 1 Color Wheel with 14 colors plus white With variable speed bi directional rainbow effect Optional Stepping linear color changing FIXED GOBO WHEEL 1 Fixed gobo wheel 17gobos White Shake and Bi directional wheel scroll at variable speeds ROTATING GOBO WHEEL 1 Rotating Gobo Wheel 9 gobos White Shake and Bi directional wheel scroll at variable speeds Rotating Gobo Replaceable IRIS Macro Function PRISM Ipc 3 facet rotating Prism bi directional with variable speeds FROST Ipc frost filter FOCUS DMX linear Focusing ZOOM DMX linear Zooming 18 23 DIMMER 0 100 linearly adjustable SHUTTER Double shutter blades 0 3 25 EP S HEAD MOVEMENT Pan 540 Tilt 270 with auto position correction BEAM ANGLE Zoom 3 8 42 linearly adjustable CONTROL DMX512 3 pin and 5 pin interfaces 20 channels in short mode 25 channels in standard mode and 31 channels in extended mode Selftest mode OTHER FUNCTIONS Adjustable Pan amp Tilt speed Use time display for the projector and the lamp respectively Modular Structure for easy maintenance Optional DMX512 Wireless Transmitter HOUSING High temperature Engineering plastic IP20
18. nel Before installation ensure that the voltage and frequency of power supply match the power requirements of the projector It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards Do not connect this device to any other types of dimmer apparatus Make sure that the power cord is never crimped or damaged by sharp edges Never let the power cord come into contact with other cables Only handle the power cord by the plug Never pull out the plug by tugging the power cord Keep the lamp clean Do not touch the lamp glass with bare hand The projector should always be installed with a secondary safety fixing A safety cord is supplied for this it should be attached as shown in installing the projector section Shields and lens shall be changed if they have become visibly damaged to such an extent that their effectiveness is impaired for example by cracks or deep scratches OO Exterior surface temperatures of the luminaire after 30 minutes operation is 45 C when steady state is achieved 60 C There is no user serviceable parts inside the projector do not open the housing and never operate the projector with the covers removed If you have any questions or suggestions don t hesitate to consult your dealer or manufacturer Always disconnection from Power when the device not in use or before cleaning or any maintenance work 3 23 INSTALL THE PROJECTOR Ax
19. r Frost O O f s Ano 0 non Pat arr mass inion 000255 TOZ 16 23 000 255 Tilt in 16 bit precision Pan amp Tilt Speeds 000 255 Pan amp Tilt Speed from Fast to Slow T ee fa anan st 20 25 31 Control 6 20 Prism is prior to Frost Filter Ifthe projector s lens becomes damaged or broken it should be replaced If the lamp becomes damaged or deformed in any way it must be replaced Ifthe light from the lamp appears dim this would normally indicate that it is reaching the end of its life and it should be changed at once aged lamps run to the extremity of their life might explode If the projector does not function check the fuses on the power socket of the projector they should only be replaced by fuses of the same specification The projector has overheat protection device that will switch off the projector in case of overheating Should it happen check if the fans are blocked or not or if they are dirty clean them before switching on the projector again Any maintenance work should only be carried out by qualified technicians LUBRICATION To ensure the smooth rotation of the rotating gobos and movement of the lens for focusing it is recommended that the bearings for the rotating gobos and the 2 sliding tracks for the focusing lens holder be lubricated every two months Use only high quality high temperature grease KEEPING THE PROJECTOR CLEAN To ensure the reliability of the projector it should be kept cl
20. r Temp 0 z Y Over Temp 0 Driver Faults X Fault 0 Y Fault 0 Factory Setup Factory Setuj actory Se Ge Factory Setup ON Test Modes Self Test OFF Self Test Self Test ON On Command Sent Lamp Status S X CX Lamp Manual Control Lamp On Turn Lamp On 9 23 Turn Lamp Off Wireless Mode XLR First Wireless Mode XLR Only Wireless Mode Wastes Mode Wireless To XLR Wireless Options Wireless Mode XLR Only Wireless Mode Wireless First Un Link Wireless Really Un Link Enter Yes Operation Mode DMX Operation Select Memory User Memory 1 Select Memory User Memory 2 Operation Mode Master Mode Select Memory Preset Memory 1 Select Memory Preset Memory 2 Operation Mode Select Memory Preset Memory 3 Select Memory User Memory 1 Select Memory F User Memory 2 Operation Mode Slave Mode Select Memory Preset Memory 1 Select Memory Preset Memory 2 Select Memory Preset Memory 3 Mode Static Scene Shutter ad Dimmer vo can Dimmer Low Dimmer Low XXX CYM Macros gt sel Cyan Yellow User Memories Edit User Memory User Memory 1 Scene XX Magenta Colour Colour Iris Iris Iris Macro Iris Macro XXX Fixed Gobo To R Gobo Wheel R Gobo Wheel XXX R Gobo Rotate S rotate R Gobo Rotate L R Gobo Rotate L XXX
Download Pdf Manuals
Related Search