PowerFlex 753 Drives - Literature Library
Contents
1. drive firmware contains corrections to the digital input processing The processing prevents the drive from responding to the level of a digital input when the digital input function is changed from an inactive de energized input to an active energized input The processing waits for an edge of the digital input This processing applies to the DI Run DI Run Forward DI Run Reverse DI Jog DI Jog Reverse and DI HOA Start commands when parameter 150 Digital In Cfg is set to 0 Run Edge Rockwell Automation Publication 750 RNO30B EN P November 2014 PowerFlex 753 Drives revision 8 002 Adjustable Voltage not Returning to Command Frequency This revision of drive firmware corrects the operation of the adjustable voltage motor control mode so that the frequency returns to the commanded frequency when commanded for all possible values of Accel Decel time parameters Parameter 383 Minimum Value is Too Large for Minimum Resistance This revision of drive firmware corrects the logic and frame rating data used for dynamic brake resistance The minimum value of parameter 383 DB Ext Ohms may now differ from the internal braking resistance value Also the internal resistance values were corrected for the frame 1 and 2 drives DeviceLogix Not Able to Migrate Between Versions This revision of drive firmware corrects the DeviceLogix macro block size eliminating errors from occurring in DeviceLogix programs that use type 3 macro2. in relation to drive parameters 960 Alarm Status B and 963 Alarm B at Fault Double Faults after Option Accept This revision of drive firmware accounts for active faults to be appropriately represented when the fault queue is cleared and persistent fault remains active Rockwell Automation Publication 750 RNO30B EN P November 2014 Known Anomalies PowerFlex 753 Drives revision 8 002 This section describes the known anomalies that are present in this revision Feedback Selection The HIM startup on the PowerFlex 753 drive includes a feedback device selection step Depending on the option modules installed that step may first ask the user to choose a port then a parameter In some situations the list of ports incorrectly shows multiple copies of Port 0 PowerFlex 753 followed by the feedback port module The incorrect behavior happens only under the following conditions e Itis the first time that startup feedback selection has been run since flashing the drive e The feedback module is a dual encoder or UFB and no other option modules are installed e A reset to defaults of the drive NVS parameters has not been performed since the drive was last flashed When the incorrect port list appears it is still possible to successfully select the feedback module port by following one of these methods e Scroll past the multiple copies of Port 0 to reach the desired feedback module e Press the Esc soft key t
3. maximum output frequency greater than 590Hz the drive will ramp to the command frequency set point and once it reaches a value greater than 590Hz for a period of time greater than 16ms the drive will trip on a Fault 31 Over Freq Implementation of Secure Flash With this revision of drive firmware an encryption layer with digital signature has been attached to the drive firmware flash file This encryption layer will not allow the flashing of firmware files that have not been digitally signed by Rockwell Automation When flashing from a revision of firmware that is not digitally signed users will first need to flash up to V11 001 to enable the secure flash feature to read the digital signature Once at V11 001 a customer can flash to any desired firmware revision level that has a secure digital signature Previous versions of drive firmware that don t have a secure digital signature embedded in the flash file will display the error shown below when a flash is attempted Now flashing fle lofi C Program Files ControlFLASH 0001 0078 0490 PF753_App_v9_001_012 dpi us An emor occurred during Flash Update FAILURE OM PROGRAMMING An error occurred or you cancelled the flash update If you did not cancel please retry If the flash update fais again please contact Drives Technical Support at supportdedrives ra rockwell com or 262 512 8176 Rockwell Automation Publication 750 RNO30B EN P November 2014 PowerFlex 753 Drives
4. transfer Press L to cancel an update started by mistake Are you ready to proceed Y N KAN The terminal program will start displaying the letter C This signals the XMODEM protocol that the download may proceed You then have one minute to start the transfer You have chosen to update gt PowerFlex T53 To update the FLASH memory you meed a terminal program capable of dowloading a binary file uweing the XMODEM protocol and a FLASH update File from Rockwall Automation When you press V to signal thal you are ready to proceed the terminal program will start displaying the letter C This signals the KAODEM protocol that the dowmload may preceed You then have one ainule to start the transfer Press CIRL io cance an update started by mistake Are you ready to proceed YH CECCCOECCH nmu e e i e Me de le b h re A en ee ea a pi aii am ERs w a ae te IMPORTANT You have one minute to complete steps 9 14 or HyperTerminal will return to step 5 where you must repeat steps 5 8 TIP To cancel the flash update at any time press CTRL X 9 Select Transfer gt Send File to display the Send File screen testi HyperTerminal 10 Click Browse and navigate to C gt Program Files gt ControlFLASH gt 0001 gt 0086 gt 0490 11 Search through the subfolder until the PF753_LP_App_v8_002_x x dpi file appears in the Select File to Send list Rockwell Automation Public
5. E Etherttet TF Deyite Puree iers 9 Aux ParSply 24 APS L4 gt Devine gb Fimbecdchedd b Host Parameters Bus VDC Hoel Groupe Compare Resuks Using DriveExecutive IMPORTANT You need DriveExecutive version 5 02 or later to interface with the PowerFlex 753 drive To obtain the latest version visit the Allen Bradley Web Updates site located at http www ab com support abdrives webupdate 1 Launch DriveExecutive and go online with the PowerFlex 753 drive To connect to the drive use a 1203 USB converter a 1203 SSS converter or an EtherNet IP network connection 2 Inthe Drives hardware view select the PowerFlex 753 drive in Figure 3 on page 4 3 Click the information icon in Figure 3 to display the drive s Properties dialog box In the Properties dialog box the Revision field in Figure 3 will show the drive s current firmware revision number Rockwell Automation Publication 750 RNO30B EN P November 2014 3 PowerFlex 753 Drives revision 8 002 Firmware Flashing Figure 3 Accessing the PowerFlex 753 Drive Firmware Revision Number Gmi pana yai Tapia Pe Dapa Comporara aia Pree vente a Hm Pare ee et Mai TE i w toc This section describes procedures to flash upgrade your drive firmware Flash kits for drives are provided on the Allen Bradley Web Updates site located at http www ab com support abdrives webupdate Flashin
6. Release Notes Allen Bradley PowerFlex 753 Drives revision 8 002 These release notes correspond to major revision 8 minor revision 2 of firmware for PowerFlex 753 drives Introduction The following information is included in this document For information about See page Determining Firmware Revision Level Using the Drive LCD HIM Using DriveExplorer Lite Full Using DriveExecutive Firmware Flashing Installing the Flash Kit Using DriveExplorer Lite Full to Flash Update Using DriveExecutive to Flash Update Using ControlFLASH to Flash Update Using HyperTerminal to Flash Update Enhancements Corrected Anomalies Known Anomalies Restrictions Rockwell Automation Support IS TIES TIS HS lla lle le Jims fier Jr iw Jie free ir Jim Rockwell Allen Bradley Rockwell Software Automation PowerFlex 753 Drives revision 8 002 Determining Firmware This section describes procedures to determine the firmware revision of your Revision Level PowerFlex 753 drive Using the Drive LCD HIM 1 Access the Status screen which is displayed on HIM power up Figure 1 Status Screen 2 Use the or gt 6 key to scroll to Port 00 for the Host Drive 3 Press the key to display its last viewed folder 4 Use the 4 lt or key to scroll to the DIAGNOSTIC folder 5 Use the or aes key to select Device Version 6 Press the Enter key to display device version information y play FW Revision is listed under Main Cont
7. Upgrade 6 From the Main Menu select the flash upgrade in Figure 5 on page 13 by pressing the number 3 key on your computer keyboard 7 Additional text appears From the Flash Upgrade menu select the PowerFlex 753 drive in Figure 5 by pressing the number 0 key on your computer keyboard 8 Additional text appears After reading the conditions select Yes in Figure 5 to proceed by pressing the letter Y key on your computer keyboard 12 Rockwell Automation Publication 750 RNO30B EN P November 2014 PowerFlex 753 Drives revision 8 002 Figure 5 HyperTerminal Test Screen Dialogue bes Ayer Tenminal i E Tlg Fis Edi vee Cal Traner Hob ojs ols Aa a USE to DFI Communications Module Revision 1 002 Build 1 Hain Menu Enter Number for Selection i gt Displey Setup Farameters ET ams use pee 12 gt i lash Upgrade O Elash Une ahs Enie Number for Selection 1 0 gt PowerFlex 753 2 gt This 1 83 USE 1 4 gt Devicellel Vou have chosen to update 0 gt PowerFlex 753 lo update the FLASH memory you need a terminal program capable of downloading a binary File using the HMODEM protocol and a FLASH update File iraa lockwell Automation When you press Y to signal thal you lare ready to proceed the terminal program will start displaying the iletter C This signals the SMODEM protocol that the download my proceed You then have one minute to start the
8. al Encoder l Rockwell Automation Publication 750 RN030B EN P November 2014 9 PowerFlex 753 Drives revision 8 002 6 In the Firmware Revision dialog box select v8 002 from the list of available updates and click Next gt Firmware Revision Catalog Number PowerFlex 753 LP via 750 Series Com SerialNumber 202D8C7A4 Current Revision 1 005 Select the new revision for this update Revisi 1 007 Control Current Folder e program files contralflash est 7 Follow the remaining prompts until the flash procedure completes and displays the new firmware revision number Using HyperTerminal to Flash Update IMPORTANT The HyperTerminal process takes at least one hour to complete 1 With the Flash Kit installed see Installing the Flash Kit on page 4 access and launch HyperTerminal as shown below S10 AH yO H i a C GLE ijg Metre n HO Hira ya b j ipren Took AD Riesworks Commactions TEASA Ej Faa e GJ adiga Bock T Rtwork Gotu Bord AET EI Hp Hra 3 gaabi i Bis Gorra Wie ard I mb ae unh Bonai aun OE ia Pong Ti Bete bed mp Cover ter Sepa kes ribe E oe Gowa e H S aaien Meah ELD aT l l Fat ria Took E y Bonn pu PET PEP ae a a Fa eee D rrnpire agban i Frapar Sarpi iar A Open fice brni EI Ingheerry front e Ej proie ie eye E Dai varkie Egi al ree SP Prajem i 10 Rockwell Automation Publication 750 RNO30B EN P Novemb
9. ation 750 RNO30B EN P November 2014 13 PowerFlex 753 Drives revision 8 002 14 xmodem file send for testi 12 With the file name highlighted click Open so it appears in the Filename data field in the Send File dialog box E Send File Folder C Program Files ControlFLASH 0001 008610490 Filename C Program Files Contro1FLASH G001 0086 9 Protocol modem Close Cancel 13 In the Protocol box select Xmodem 14 Click Send A dialog box appears and reports the progress of the update This process takes at least one hour for HyperTerminal to complete When it is complete the message Flash Complete appears Sending C Program Files ControlFLASH 0001 0086 0490 PF753_LP_App_vi_0 Packet 477 Error checking ERC Retnes fo Total retnes lo Last error File am Ti 598K of 4242K Elapsed 00 09 23 Aemainundg 00 57 15 Throughput 1086 cps Cancel cps bps 15 Press any key to continue 16 Press the Enter key to return to the main menu Rockwell Automation Publication 750 RNO30B EN P November 2014 PowerFlex 753 Drives revision 8 002 Enhancements This section describes the enhancements included in this revision There are no enhancements associated with this drive firmware release Rockwell Automation Publication 750 RNO30B EN P November 2014 15 PowerFlex 753 Drives revision 8 002 Corrected Anomalies 16 This section describes the anomalies corre
10. blication 750 RNO30B EN P November 2014 PowerFlex 753 Drives revision 8 002 4 Now that the correct communication device has been selected you must select which device is being updated With the Select the PowerFlex dialog box displayed follow these steps a Expand the hardware view for the communication path you are using in Figure 4 b Select the drive icon that represents the PowerFlex 753 drive you are updating in Figure 4 c Click OK in Figure 4 Figure 4 Selecting the Correct Drive to Flash Select the PowerFlex 753 LP via 750 Series Comms i devic Browsing node 10 91 24 7177 found PowerFle PowerFie 10 91 100 70 SLC 3 05 J ne xX 10 91 24 104 Unrecogni 10 97 24 10 91 24 10 91 24 2e lOMM PowerFle 1747 55 a 10 951 24 105 PowerFlex Fi 7 ej 20 91 24 106 Drivelogik 19 91 24 53 10 91 24 54 10 91 24 1756 ENB 1768 ENB 1756 ENB 10 91 24 109 Urr g t 7 10 91 24 110 Unrecogni A 10 91 24 60 10 91 24 66 10 91 24 17565 ENB 1769L35 1091 24 68 10 91 24 55 shale e 5 In the Multiple Assemblies Found display box select Port x PowerFlex 753 from the list and click OK choose the acpembly that pou would like to update from the bist below T i Pai F le Pjan a Port 1 20 HIM x6 Port 2 Hot Prezent Port 3 Mot Present Por 4 DeviceNet Port 5 1 0 Module 247 Port 6 Du
11. blocks when downloaded Calculation of the position integral term System Bandwidth Calculation This revision of drive firmware increases the max allowable value position integral This change has been made for compatibility with Logix V20 and higher PM Motor Encoder Offset Test on Power Up This revision of drive firmware adds logic to ensure that the PM IPM Oftset test is successfully completed before running in a PM or IPM motor control mode If the scheduled test does not successfully complete fault 197 PM Offset Failed will occur and the offset test will be automatically rescheduled 9xx Non Recoverable Faults are not recorded This revision of drive firmware provides fault information fault code and time stamp in the fault queue for all 9xx level faults Associated documentation has also been updated to provide appropriate information Rockwell Automation Publication 750 RNO30B EN P November 2014 17 PowerFlex 753 Drives revision 8 002 18 Ethernet Fault Actions Last Stop Source Not Updated This revision of drive firmware provides support to record the appropriate port as the last stop source when the drive stops due to communication loss The pertinent port must be configured to stop on a communication loss for the last stop source to be updated appropriately Alarm Dynamic Brake OT is Not in Parameters 960 or 963 This revision of drive firmware sets a drive alarm status bit for the Dynamic Brake Overtemp alarm
12. cted in this revision 918 fault in IPM Encoderless FV Mode The drive would throw an F918 Control Task Overload fault when accelerating through the 7 Hz speed because of the way it changed PWM carrier frequency at this speed This anomaly only affected drives operating in the IPM Flux Vector motor control mode without encoder feedback It did not affect any other motor control modes Aux Input Fault Status B This revision of drive firmware changes the operation of parameter 953 Fault Status B bit 0 Aux Input Flt to remain set until the fault is cleared from the drive Previous revisions of firmware would clear this bit as soon as the auxiliary fault input condition cleared Digital Input Config Alarms B amp C This revision of drive firmware corrects the digital input conflict alarm settings Additional Automatic Tach Switchover Configurations for PM Motors This revision of drive firmware provides additional support for Automatic Tach Switchover selections for IPM and SPM motor control Specific additions for IPM motor control include auto switchover from one feedback source to another and auto switchover from feedback to open loop Inconsistent Min Max Default for 10 Option Modules This revision of drive firmware provides consistent minimum maximum and default values for parameters 76 Anlg Out0 Stpt and 86 Anlg Out Stpt of IO option modules in offline configuration Digital Input Run Processing This revision of
13. er 2014 PowerFlex 753 Drives revision 8 002 2 A New Connection dialog box appears a Enter the connection device name in the Name field or select an icon from the library b Click OK once you have finished 3 A Connect To dialog box appears a Use the Connect using drop down menu to select the appropriate connection device b Click OK once you have finished ConnectTo E EAE DP i Enter details for the phone number that you want to chat County regon United States 1 Area code E Phone number 7 E Connect using NmeaDev0 bd NmesaDevt Rockwell Automation Publication 750 RNO30B EN P November 2014 11 PowerFlex 753 Drives revision 8 002 4 A Properties dialog box will appear for the selected connection device a Use any of the drop down menus to change the various port settings b Click OK once you have finished x COM4 Properties E i Bits per second 115200 Data bits s paity Nowe E Stopbits 1 a Flow cortict 5 After you click OK you will get a blank screen Press Enter on your computer keyboard so the following test screen appears pesti Hyper Terminal o 5 x fie fide sew Call Trane Help oja eis cell USE to DPT Communications Module Revision 1 002 Build 1 Hain Menu Enter Huwber for Selection D Display Setup Paraseters Display Event Queue a gt Flash
14. es dialog box click the Component Details tab 5 With the PowerFlex 753 drive selected click Flash Update E Han Contro Board W Power Board 6 Rockwell Automation Publication 750 RNO30B EN P November 2014 PowerFlex 753 Drives revision 8 002 6 From the list of available devices select the PowerFlex 753 drive and click Next gt Select Device To Update e x Select a device to flath update Flash updating the device firmvrare may cause the device to load defaults It is recommended that pou save the settings to your PC before proceeding Note Only devices that support Flash will be shown in the device tree Node 10 91 24 111 U PoweFlexs 54 Revision 1 007 a 1 20 HIk X6 Revision 1 005 Pla 4 DeviceNet Revision 1 003 Harmony Path USMEQTJSYORENAIAB _ETHIP 1410 91 24 111 IMPORTANT Flash updating the device firmware may cause the device to load defaults It is recommended that you save the setting to your PC before proceeding 7 From the list of available updates select v8 002 xxx and click Next gt Select Flash Update PowerFlex 753 Flash Update File Location C Program Files ControlFLAS5H 0001 1008c 0890 Available Flash Updates v 1 007 148 PF753LPADD 8 Follow the remaining prompts until the flash update procedure completes and displays the new firmware revision Rockwell Automation Publication 750 RNO30B EN P November 2014 7 PowerFlex 753 Dr
15. g can be performed using a 1203 USB or 1203 SSS converter For information on connecting either converter to your drive refer to the 1203 USB USB Converter User Manual publication DRIVES UM001 or the 1203 SSS Smart Self powered Serial Converter User Manual publication 20COMM UMO01 Installing the Flash Kit 1 Install the flash kit utility from the Allen Bradley Web Updates site for the PowerFlex 753 drive which includes the latest version of the ControlFLASH utility and deploys firmware files for using HyperTerminal on your computer 2 You are now ready to use DriveExplorer DriveExecutive Control FLASH or HyperTerminal to update the drive Refer to the respective section and follow the instructions Rockwell Automation Publication 750 RNO30B EN P November 2014 PowerFlex 753 Drives revision 8 002 Using DriveExplorer Lite Full to Flash Update 1 With the Flash Kit installed see Installing the Flash Kit launch DriveExplorer and go online via a 1203 USB or 1203 SSS converter with the PowerFlex 753 drive 2 Inthe Drives hardware view select the PowerFlex 753 drive in Figure 3 on page 4 3 Click the information icon in Figure 3 to display the drive s Properties dialog box 4 In the Properties dialog box click the Details tab 5 With the Main Control Board selected click Flash Update PowerFlex 753 480V 232A 10 91 24 170 xj General Detal Status Feedback Alarms Fiti Diegrcatics Sya
16. ives revision 8 002 Using ControlFLASH to Flash Update 1 With the Flash Kit installed see Installing the Flash Kit on page 4 launch ControlFLASH by selecting Start gt All Programs gt Flash Programming Tools gt Control FLASH 2 On the ControlFLASH Welcome dialog box click Next gt Welcome to ControlFLASH Welcome to ControlFLASH the firmware update tool ControlFLASH needs the following infomation from you before it can ra begin updating a devine EUG ME 1 The Catalog Number of the target device 2 The N elwork Contiguration parameters optional 3 The Network Fath to the target device 4 The Firmware Revision for this update 3 The Catalog Number dialog box appears From the list choose the communication device you will use to update the PowerFlex 753 drive In the figure below the embedded EtherNet device is selected Once the appropriate communication device is selected click Next gt Catalog Number Enter the catalog number of the target device PowerFlex 53 LP via 750 Senes Comme Control PowerFlex 700VC Series B PowerFlex O0VC Senes B via 20 COMM PowerFlex 753 HP via 1769 5M1 Compact 1 0 PowerFles 753 HP via 20 COMM Q 7 20K CNETG PowerFlex 753 HP via 750 Series Comme PowerFlex 53 HP via DPI Comme PowerFles 53 LP via 1769 SM1 Compact 0 PowerFlex 753 LP via 20 COMM Q 7 20K CNETGI PowerFles 59 LP via 5U Senes Comms PowerFlex 753 LP via OPI Comme Rockwell Automation Pu
17. o back up one screen then select Feedback and press the Enter soft key to display the port selection screen a second time This time the correct list will be shown Persistent Stop Command with Profile Message Fault Action In an application with the use of a PowerFlex 753 along with the 20 750 ENETR dual port Ethernet IP module a persistent stop command may appear in some cases The action of disconnecting the Ethernet cable from the 20 750 ENETR module which will result in the drive stopping may follow with a nuisance fault action This fault action previously noted is persistent communication of stop commands Saving Parameters using Drive Explorer When a user attempts to save all parameters with a PowerFlex 753 and a 20 750 ENETR dual port EtherNet IP communication adapter DriveExplorer in some cases fails to complete the save function To exit the loop click the cancel button and check if the text file had been saved Rockwell Automation Publication 750 RNO30B EN P November 2014 19 PowerFlex 753 Drives revision 8 002 Restrictions 20 The following restrictions apply to this revision of firmware Max Output Frequency Limited to 590Hz This revision of drive firmware places a limit on the maximum output frequency of the drive In previous versions of drive firmware the maximum operating frequency of the drive was 650Hz The new maximum output frequency limit is 590Hz If a previous application allows for a
18. quarters Americas Rockwell Automation 1201 South Second Street Milwaukee WI 53204 2496 USA Tel 1 414 382 2000 Fax 1 414 382 4444 Europe Middle East Africa Rockwell Automation Pegasus Park De Kleetlaan 12a 1831 Diegem Belgium Tel 32 2 663 0600 Fax 32 2 663 0640 Asia Pacific Rockwell Automation Level 14 Core E Cyberport 3 100 Cyberport Road Hong Kong Tel 852 2887 4788 Fax 852 2508 1846 Publication 750 RNO30B EN P November 2014 Supersedes 750 RNO30A EN P May 2013 Copyright 2014 Rockwell Automation Inc All rights reserved Printed in USA
19. revision 8 002 Rockwell Automation Support To assist you Rockwell Automation provides technical information on the web At http www rockwellautomation com support you can find technical manuals a knowledge base of Frequently Asked Questions FAQs technical and application notes sample code and links to software service packs and a MySupport feature you can customize to make the best use of these tools Rockwell Automation also provides complimentary phone support for drives option modules and peripherals If you experience a problem with an option module please review its documentation For further help contact a Customer Support representative United States 1 262 512 8176 Monday Friday 7am 6pm CST Outside United States Please contact your local Rockwell Automation representative for any technical support issues For an additional level of technical phone support for installation configuration and troubleshooting we offer TechConnect Support programs For more information contact your local distributor or Rockwell Automation representative or visit http www rockwellautomation com support Rockwell Automation Publication 750 RNO30B EN P November 2014 21 U S Allen Bradley Drives Technical Support Tel 1 262 512 8176 Fax 1 262 512 2222 E mail support drives ra rockwell com Online www ab com support abdrives www rockwellautomation com Power Control and Information Solutions Head
20. rol Board see Figure 2 Figure 2 Device Version Information Screen Product Series A 2 Rockwell Automation Publication 750 RNO30B EN P November 2014 PowerFlex 753 Drives revision 8 002 Using DriveExplorer Lite Full IMPORTANT You need DriveExplorer version 6 02 or later to interface with the PowerFlex 753 drive To obtain the latest version visit the Allen Bradley Web Updates site located at http www ab com support abdrives webupdate 1 Launch DriveExplorer and go online with the PowerFlex 753 drive To connect to the drive use a 1203 USB converter a 1203 SSS converter or an EtherNet IP network connection 2 In the Devices hardware view select the PowerFlex 753 drive Once selected information regarding the PowerFlex 753 drive is shown in the right panel including the current firmware revision number 69 OriveEsplorer Ble Edt Expore tons Hep DE DEM Mo rE Dees Etherhiet TP Direct F Jania eee PowerFlex 753 Slo Powerflex 7534800 2 wile iy Migraine PowerFlex 753 Ceca Oana 480V 7 1 A Petiback amp bo Drive Og hens ZOF D2Pi1 Protector Speed Control Standard FO2 1CS6P1I Torque Conia 3 9 fatin Conivel Port 0 10 91 24 93 Crmmurication Revision 1 007 Seriea A Dajcs Aggkca bons 1 20 NIM 16 LED MIH Stopped Devine Parameters Feedback Output Current CC Bus Volts 7 17203 USB USB to DPI Device Parameters 6 20 COMM
21. tern Time Language Produa Serial Number SN202DEC7A Gave As Tet E SET Larti E aad Fumerane Aavan 1 005 Pini Hatke Change Number 02 Application Flash Uplate E Reson 1 015 178 m Checkoum bE 206 Frare Fah Tabie Kerden 2 008 7011 Checkoum 8424 Boot Lode Reson 1 002 06 Checksum EDE E Power Board Fineas Revco 1 001 Hardveare Change Humber Oi __ chee IMPORTANT Flash updating the device firmware may cause the device to load defaults It is recommended that you save the setting to your PC before proceeding Rockwell Automation Publication 750 RNO30B EN P November 2014 5 PowerFlex 753 Drives revision 8 002 6 From the list of available updates select v8 002 xxx and click Next gt Select Flash Update PowerFlex 753 Flash Update File Location C Program Files ControlFLASH 0001 00sec 0590 Browse Available Flash Updates v 1 007 148 PF753LPADD 7 Follow the remaining prompts until the flash update procedure completes and displays the new firmware revision Using DriveExecutive to Flash Update 1 With the Flash Kit installed see Installing the Flash Kit launch DriveExecutive and go online via a 1203 USB or 1203 SSS converter with the PowerFlex 753 drive 2 In the Drives hardware view select the PowerFlex 753 drive in Figure 3 on page 4 3 Click the information icon in Figure 3 to display the drive s Properties dialog box 4 In the Properti
Download Pdf Manuals
Related Search