(WM169) operating and maintenance manual
Contents
1. p ZZ SS Ap a Soa DG 1 NS LL Ss Model RSE 2001 LA 341 5 E B 179 246 L Model RSE 2 4 Fig 5 Overall dimensions Date of issue Revision Revision date Page 12 of 32 04 06 2014 8 20 07 2015 Pietro RSE METER ENGLISH seas Use and Maintenance Manual Fiorentini PM Version 5 2 Connection to the system After installation RSE must be connected to the system Before connection make sure that at least the portion of the plant upstream of the meter is sectioned and that therefore there cannot be any flow of gas during the installation Before connection make sure that the maximum system pressure is lower than the maximum pressure set for the meter which is fixed and equal to 0 5 relative bar If necessary use fittings not supplied to connect RSE to the piping During the tightening of the fittings do not exceed the torque of 110Nm RSE operates only in vertical position RSE is provided with an on off valve in the open status therefore it is ready to deliver and measure Verify2. Rated capacity of about 8 5 Ah The Bobbin technology assures a maximum current limited by significant intrinsic internal resistance however it still provides sufficient current for the device operation Wiring with polarized connector to assure proper connection to the printed circuit board The cell is fastened inside the meter it cannot be replaced and it is protected by metrological seals 169 MHz radio battery The radio version has an additional non replaceable battery placed in the metrological area and therefore not accessible by the operator A single non rechargeable cell with Lithium Thionyl chloride technology Li SOClz is used The main features are Size C with spiral technology Rated voltage equal to 3 6 Vdc Rated capacity of about 7 0 Ah The spiral technology allows the battery to provide peak currents appropriate for the operation of the enhanced 169 MHz radio battery Wiring with polarized connector to assure proper connection to the printed circuit board The cell is fastened inside the meter it cannot be replaced and it is protected by metrological seals Reference operating conditions Amb temperature 5 of the time 25 C 20 10 C 50 22 C 20 55 C 5 70 C Communication Tx radio cycle Short message volume measurement transmitted 5 messages sent per day Tx Rx radio cycle Tx Rx talks with long message 1 command day User interface 5 minutes per month Display
3. SUCCESS Under the SV menu the display will show VAL 00 A open valve 4 2 Digital outputs RSE does not have any digital outputs 4 3 Data recording With reference to the standards of the series UNI TS 11291 RSE implements in particular the following services UNI TS 11291 1 4 3 3 Service Dynamic multi rate capacity UNI TS 11291 1 4 3 7 Service Metering and load profiles UNI TS 11291 6 5 Detection and recording of data Date of issue Revision Revision date Page 10 of 32 04 06 2014 8 20 07 2015 oC Pietro RSE METER ENGLISH seas Use and Maintenance Manual Fiorentini PM Version 4 4 Acquisition The flow rate measurement is carried out continuously by means of the mechanical system consisting of two measuring chambers of known volume with deformable diaphragms which expand and contract alternately This movement induced by the pressure difference between the inlet and outlet passages operated by a crank mechanism is transmitted to a pin that makes a complete turn every cyclic volume of gas passing through The movement of the pin causes the rotation of an encoder such rotation is detected by means of two optical sensors The management of both HW and SW is carefully optimized to minimize the consumption of the measuring circuit and the processor awakening time The optical sensor provides sufficient resolution to allow the measurement of the amount of gas both during operation and for the certifi
4. 8 Press the upper button twice The meter is counting with normal resolution 7 1 17 Maximum conventional flow rate Abbreviation Qconv_max Format 2 integers and 3 decimals Unit m h Pressing Enter Legal relevance YES Date of issue Revision Revision date Page 27 of 32 04 06 2014 8 20 07 2015 oC Pietro RSE METER ENGLISH seas Use and Maintenance Manual Fiorentini PM Version 7 1 18 Date Abbreviation D Format dd mm yy Unit Pressing enter E By pressing enter it is possible to display the version CRC of the certificate modules and other information on the software The submenus are listed below CRC16 Legally Relevant SW Legally Relevant SW internal release CRC16 Not Legally Relevant SW Not Legally Relevant SW internal release Release date Release time CRC16 Boot module CRC16 Header module CRC16 Loader module CRC16 Hal module CRC16 Kernel module CRC16 Stm32lib module CRC16 KSystem module CRC16 Security module CRC16 Display module CRC16 Metric module CRC16 Plugin header CRC16 Plugin module System global uptime days including low power and running mode System global uptime h m s including low power and running mode System running mode uptime days System running mode uptime h m s Total number of events Code started events Consid param modified events Security param modified events New SW run events Upgrade errors Total CRC errors Kernel Data Kernel only
5. CRC errors Attempted fraud events Legal relevance YES Date of issue Revision Revision date Page 28 of 32 04 06 2014 8 20 07 2015 g Pietro RSE METER ENGLISH seas Use and Maintenance Manual Fiorentini PM Version 7 1 19 Time Abbreviation H Format hh mm Unit Pressing enter E By pressing enter it is possible to view the log of the last 32 firmware updates For each firmware updates a block of three submenus is added CRC16 LR of the firmware Updating date Updating time The firmware loaded at the factory is the oldest entry date and time set to 00 00 00 If the download fails four dashes are displayed instead of CRC 16 LR Legal relevance YES 7 1 20 Current rate Abbreviation Fn Format 1 digit Possible values 1 Range 1 2 Range 2 e 3 Range 3 Unit Pressing enter Legal relevance YES Date of issue Revision Revision date Page 29 of 32 04 06 2014 8 20 07 2015 oC Pietro RSE METER ENGLISH seas Use and Maintenance Manual Fiorentini PM Version 8 Configuration The device configuration can occur from the local ZVEI port or remotely from SAC always by means of the DLMS protocol as specified in the provisions of the standards series UNI TS 11291 9 Maintenance 9 1 Ordinary maintenance 9 1 1 Replacing the batteries The RSE metrological battery is sized to assure an autonomy of more than 15 years under normal environmental and operating conditi
6. E E 12 J SAO e e E E E E E E E E E mates cmcutes 12 54 Me chanics instalatiONMssirsser E A EE Ea a EERE 12 BZ Connection TO TMG syste Minesiseresoiein EE 13 5 2 1 OS TVS ZV Cl ROIS aenea E EE 13 OVE SU oceans ps ct tention aa esse ee gee care nase sttaea EEE EE Gente E E TE 14 5 3 1 Connecting TICs 52 cio tacea sane eenactecciesentnnuednent AEN E E iA 14 5 3 2 UPEN Se Sats stern rt sete ees detest tv nineteen ea parece 2G acetew ss saie naw ance eed ee demeaeedionaeesets 14 5 4 Security and fraud Prevention ccccccssscccceesscccceseccceesececeeenscceseuseceeeeeceeseeeeceeseesecessenecesseggecetsenas 15 o ISOM MMe AGO e E E E 16 e KEDO e E E ne ee eee ee 16 el D Py ea E A EEE E T TS 16 6 2 1 Display testing capabilities nosenosenssseensrerssressrressrreseeresrresrrrssrroseerssrersreresrresrerseeresrreeseersse 16 6 2 2 Mena To e a E E E E E 17 Date of issue Revision Revision date Page 2 of 32 04 06 2014 8 20 07 2015 oC Pietro RSE METER ENGLISH seas Use and Maintenance Manual Fiorentini PM Version 6 2 3 Units of measurement Held zeiserrsrepris arn nn n EENEN E ENEN EET 17 6 2 4 Nomer i Oee E A E piuerecianvearsiiesanstaupoeas deretouetuciares 18 6 2 5 komandalarini NA ea sions E E EE E EE O NE 18 fa OMIM SU GUY soe et ceteps e E E E E E E E 19 Tes CA a ee eee eee eee eee eee 19 7 1 1 Totalizer of volumes under reference conditions in the current billing period essc 19 12 Totalizer of volumes sub
7. Format 5 integers and 3 decimals Unit m Pressing enter Legal relevance YES 7 1 10 Totalizer of volumes for price range 3 in the previous billing period Abbreviation T3 PRE Format 5 integers and 3 decimals Unit m Pressing enter Legal relevance YES 7 1 11 Invoice date 09 02 13 Abbreviation DF Format dd mm yy Unit Pressing enter Legal relevance YES It expresses the date on which the data of the previous period do refer T TA T1 T2 T3 PRE Date of issue Revision Revision date Page 21 of 32 04 06 2014 8 20 07 2015 oC Pietro RSE METER ENGLISH seas Use and Maintenance Manual Fiorentini PM Version 7 1 12 Diagnostics Abbreviation DG Format 4 digits hexadecimal code Unit Pressing enter Legal relevance YES The encoding of the information shown complies with the provisions of the standard UNIT11291 11 chapter 5 4 9 2 given here below Bit Meaning 15 Reseved o 14 Reseved o 13 Reserved 12 __ 1 Valve enabling anomaly gt S 11 1 Daylight Saving Time active 10 1 Tampering detected _9__ 1 Battery level critica 1 Battery level lower than 10 See fe e E T 6 1 Memory error 5 1 fFlowrate error 4 1 Device generic error 3 1 Measurementalgorithmerror S 2 1 Metrological Event Log gt 90 1 1 MetrologicalEventLogcomplete S 0 1 Clocksynchronizationfailed o The 16 bits mentioned above are represented using a hexadecimal enco
8. GSM 1 1 Identification of the product The product can be identified by the metrological cover shown in fig 1 positioned on the front of the device as shown in fig 2 which bears the following symbols and data gt Type of model gt Name of the logic device Type of model Code format RSE 2001 LA RSE 2 4 Name of the logic device Format SMG R 03 WV YY XXXXXX SMG Fixed data indicating the manufacturer Samgas Srl according to the Flag Association coding R Reserved 03 Type of device GAS meter W Type of caliber V Type of communication YY Year of production XXXXXX Serial number The forecast product versions are given here below Version Code W Type of caliber Version Code V Type of communication 169 MHz 58 MHz ee en Date of issue Revision Revision date Page 5 of 32 04 06 2014 8 20 07 2015 wa Pietro iF Aai sean Use and Maintenance Manual _ pn D wae S J n SS aa a n Mec P DN Mi lt venais OIML R137 1 amp 2 2012 EN 1359 1998 A1 2006 g mS SAMOS veiling OIML R137 1 amp 2 2012 EN 1359 1998 A1 2006 T10683 G4 WM169 RSE 2001 LA ma a G6 WM169 RSE 2 4 M15 0122 15 2 4 dm Pmax 0 5 bar 12 dm pmax 0 5 bar s Qmin 0 06 m h Classe 1 5 V Qmin 0 04 m3 h Classe 1 5 Q 0 6 m h tm 25 C 55 C Qmax 6 m h tp 157 T H3 M2 E2 tsp 15 C E go E SMGR0340YYXXXXXX oO S
9. The duration of the conditions is monitored and recorded Metrological seal Metrological seal Date of issue Revision Revision date Page 15 of 32 04 06 2014 8 20 07 2015 oC Pietro RSE METER ENGLISH seas Use and Maintenance Manual Fiorentini PM Version 6 User interface The user interface consists of three operator keys and a display The following paragraphs describe the interaction between the operator and the user interface and the meanings of the various fields available on the display With reference to the standards of the series UNI TS 11291 RSE implements in particular the following services UNI TS 11291 1 4 3 5 Service Consumer information UNI TS 11291 6 8 2 Construction requirements Display 6 1 Keyboard The interaction occurs through three keys up and down scrolling blue color and Enter green on the front of the device 6 2 Display The display is a black and white LCD display consisting of 8 7 segment characters and a series of icons and symbols whose meaning is described below The size of the digits represented by the 8 7 segment characters are compatible with the requirements of MID and EN12405 1 The construction technology of the LCD element display is such as to assure a lifetime of over 15 years under operating conditions which include also prolonged exposure to sunlight DHFnTTAT1T2T3PTPRE DFDGMUIDSVSD Qeonv max COO dad Ug mh MAA at 4 E The meaning of the graphical
10. buttons ZVEl Temperature measurement 1 measurement every 29 sec Code update 2 times in 15 years a Date of issue Revision Revision date Page 32 of 32 04 06 2014 8 20 07 2015
11. elements is outlined in the following table Menu field Each menu can be identified by a letter or a combination of letters and numbers Units of measurement See table for units of measurement field Numeric field 8 7 segment digits displaying the value associated with the displayed menu Icons and l ein See table for icons and alarms To allow a long battery life the display is usually kept OFF To activate it just press the green central key 6 2 1 Display testing capabilities When the display is turned off and the green central key is pressed a test Sequence is displayed to check the presence of defective segments or icons The test sequence lasts 3 seconds and turns on all segments and icons of the display at the same time At the end of this step the first page of the menu is displayed The description of the menu and the information display order are shown below Date of issue Revision Revision date Page 16 of 32 04 06 2014 8 20 07 2015 mg Pietro jokers Use and Maintenance Manual 6 2 2 Menu field Totalizer of volumes under reference conditions Totalizer of volumes under reference conditions for range 1 Totalizer of volumes under reference conditions for range 2 Totalizer of volumes under reference conditions for range 3 Added to T TA T1 T2 or T3 When the count refers to previous billing periods DF fier DG fre i Message to the user Status of the valve Quen max 0T oonvento
12. least 15 years The battery autonomy was estimated in the following reference operating conditions The 169 MHz radio transmission battery is dimensioned to assure the operation of RSE for at least 15 years The battery autonomy was estimated in the following reference operating conditions 169 MHz Radio Communication Tx Only radio cycle Short Message volume reading transmitted 5 messages day Tx Rx radio cycle Tx Rx talks with long message Display message ZVEI communication 5 minutes per month Valve control 1 complete control including 1 opening and 1 closing every year 1 valve test period valve periodic test 1 cycle per month Ambient temperature profile 5 of the time at 25 C 20 of the time at 10 C 50 of the time at 22 C 20 of the time at 55 C 5 of the time at 70 C RSE implements and manages service quality logs available only through the communication channels not on the display able to verify the deviation of the actual operating conditions from the reference ones 5 3 1 Connecting the batteries RSE is supplied with the metrological battery already connected and inserted in the related compartment therefore RSE is ready for operation 5 3 2 Supply status Power status shows the current battery level The functionality of calculation of the actual use of the battery has been implemented in order to signal when the limit of 90 is reached A weight has been configured for the main activ
13. of issue Revision Revision date Page 11 of 32 04 06 2014 8 20 07 2015 oC Pietro RSE METER ENGLISH seas Use and Maintenance Manual Fiorentini PM Version 4 8 User interface The user interface consists of a LCD display and three operator keys The interface allows only the consultation of the parameters and provides access to the SD status of the device menu 5 Installation RSE is suitable for installation in hazardous areas classified as ATEX Zone 2 RSE meets the protection requirements of type II 3G Ex ic IIB T3 Gc 3G For use in Zone 2 atmospheres therefore it is safe in case of operation without interferences IIB It establishes the maximum ignition energy that shall not be exceeded and therefore with what types of gas the product can be used in a safe manner e g ethylene T3 It defines the maximum allowable surface temperature equal to 200 C Caution Before beginning with the installation read and verify the safety instructions contained in the first chapter carefully 5 1 Mechanics installation The overall dimensions of RSE are shown below RSE is fastened to the system using a special shelf for GAS meter 190 _ 172 5 223
14. pressed for about two minutes the display returns to off status By pressuring the up and down keys it is possible to navigate through the various menus Pressing the up button it is possible to go back to the previous page pressing the down button it is possible to move to next page Some menus consist of various submenus in this case the letter E Enter is displayed on the lower right corner of the display By pressing the green Enter button the submenu appears By pressing the up and down buttons it is possible to navigate inside the submenus 7 1 Chapters The various menus are identified by the letters shown on the display under menu field Here below there are the menus displayed in sequence scrolling down after switching on the display The sequence is circular the list can be scrolled indifferently downwards and upwards Once the corresponding end is reached the display continues in the order defined below 7 1 1 Totalizer of volumes under reference conditions in the current billing period U 1990 100 m Abbreviation T Format 5 integers and 3 decimals Unit m Pressing enter Legal relevance YES 7 1 2 Totalizer of volumes subject to alarm in the current billing period Abbreviation TA Format 5 integers and 3 decimals Unit m Pressing enter Legal relevance YES Date of issue Revision Revision date Page 19 of 32 04 06 2014 8 20 07 2015 oC Pietro RSE METER ENGLISH seas Use and Mainte
15. EGSI on 27 12 2013 Fig 4 Meter internal view Date of issue Revision Revision date Page 9 of 32 04 06 2014 8 20 07 2015 oC Pietro RSE METER ENGLISH seas Use and Maintenance Manual Fiorentini PM Version 4 Main functions 4 1 On off valve With reference to the standards of the series UNI TS 11291 RSE implements in particular the following services UNI TS 11291 1 4 3 4 Service Supply management UNI TS 11291 6 6 Flow on off The gas flow on off valve is located within the body of the meter into the inlet connection and is not accessible without causing permanent damage to the meter itself The purpose of the valve is to intercept the gas flow towards the user exclusively for the commercial purposes In no way or condition the valve has to be considered and used as a useful device to assure safety conditions in the user s plant in case of possible or patent gas leakages The valve is specifically designed to assure its performance and functioning for at least 15 years and it is able to provide the control microprocessor with the actual status of the valve closed open and with information about its correct operation The valve can be closed e Due to a remote control sent via wireless communication channel e g from the SAC Remote Management Center e When changing the battery is not authorized Due to a break in attempted beyond the threshold e When there is no communication for a configurable time e When t
16. MGR0360YYXXXXXX oO oe a CE E 2015 CE amp 201 II 3G Exic IIB T3 Gc A II 3G Exic IIB T3 Gc a e S J CEC 14 ATEX 011 CEC 14 ATEX 011 25 C lt Tamb lt 55 C q 25 C lt Tamb lt 55 C H IP55 IP55 OO we MY See Fig 1 Fig 2 1 2 Packaging content The package contains the following parts Device RSE device including o Metrological battery o Communication battery not replaceable o Two plugs for the protection of the connection fittings The batteries are inside in their operation seat already electrically connected Date of issue Revision Revision date Page 6 of 32 04 06 2014 8 20 07 2015 oC Pietro RSE METER ENGLISH seas Use and Maintenance Manual Fiorentini PM Version Manual User Manual The user manual and the use and maintenance manual are available for download on the website www fiorentini com Certificates The EC declaration of conformity is enclosed to the transport documents of the instrument 2 Safety instructions RSE is an intrinsically safe device suitable for use in hazardous areas classified as Zone 2 Group IIB The minimum installation category is ATEX Category II 3G The harmonized CENELEC standards relevant to the compliance with the EHSR requirements Essentia
17. Pietro Fiorentini RSE SAMANJ Smart GAS meter RSE 2001 LA RSE 2 4 Use and Maintenance Manual Point Multipoint Version PM Rev Date 8 20 07 2015 oC Pietro RSE METER ENGLISH seas Use and Maintenance Manual Fiorentini PM Version Index T DDU ON ee E E E E E E E E 5 te Taenu Onor Nep odU C eeaeee a E E A A A 5 L2 PACKS NE CO E aE E ATE E te 6 PE A EES AS R NET EAE EE 7 21l Electrostatic discharges sunrc Aaa a ieee 7 Dds COMMOECEING LO Oter dEV CE Sac icc aed tome easnarsse anced eeesuauieaed dacaitedneensncosmnceanene savant ose EE 7 ko Feen OV O ee eee eee ee ee eee 7 2 4 Safety instructions for installation in the hazardous Area ccseecccesssscccceeseccccesececceusceceesusecessegees 8 3 18 c ec lee che UON eee ee en he ere eae eine ener ete ee eee ee eae 8 de MA TEMG U ONG iss asatesisect death adios E E A E 10 ig ONON AI recs areas sect steasdev E A eater decaaenanmneatteuaeauenaitaneaentarnees 10 4 1 1 Procedure for opening the valve through the user interface ccccccessecceeeeeseceteeseceeeeeeeees 10 BZ DEOU aiar E A E E E A a roantane te voeak santos 10 A DITE OE on E E E A E A eee ee OA 10 AA AAO E A E A A E A E A 11 AS E AIC OS CE T EE EE E E AEE Senet 11 EO ACV 0 6 eee eee rece e eee Cnn ere ere erence er er ees ee reer eee 11 A CONMIGO ee ce gece E E pa acts ea deo E EEA E A ES 11 DB UTE ACC sera sacuscecevorsaviceeysta tons seccenslsaid rsinseht A A E EE E A
18. Revision Revision date Page 4 of 32 04 06 2014 8 20 07 2015 or Pietro RSE METER ENGLISH seas Use and Maintenance Manual Fiorentini PM Version 1 Introduction RSE is a family of products dedicated to measuring gas volume which involves the application in end points of redelivery of natural gas networks This document refers to the versions RSE 2001 LA and RSE 2 4 The product incorporates a mechanical device for measuring the gas volumes based on the diaphragm metering technology with an electronic processor able to guarantee the functions provided by the resolution 631 2013 R GAS issued by AEEGSI on 27 12 2013 as well as to allow the remote reading and remote control of the flow without the use of additional external devices RSE meters are used in low pressure measuring systems lt 0 5 bar gauge with a flow rate lower than 10m h class A2 according to the classification of UNITS 11291 This document provides information about the use of the involved device with application starting from the firmware release LR 1 09 NLR 2 22 RSE 2001 LA and RSE 2 4 are available in different models with the following main common features IP 55 protection Integrated temperature sensor Local optical communication port complying with CEI EN 62056 21 ZVEI LCD display 3 front keys user interface VV VV YV The various models differ in the following features gt Type of modem o Wireless M Bus 169 Mhz mode N o 868 Mhz o GPRS
19. cation production calibration steps using in this case a modified counting algorithm The two pairs of LED phototransistor sensors are positioned at 90 to one another For each rotation of the encoder divided into full and empty sectors a given sequence of statuses is therefore available The coding of this sequence allows identifying a regular counting a reverse rotation or an oscillation In this way it is possible not to affect the taken measurement in any way The system consisting of an encoder and optical sensors represents the interface between the measuring mechanics and the calculation and management electronics The piloting and detection of the optical sensors is entrusted directly to the microprocessor which performs also an ongoing diagnostic activity to highlight any faults and fraud attempts made by blinding the sensors The piloting of the sensors is carried out in a controlled manner which is such as to assure proper operation during the whole RSE life cycle The measurement of the temperature required for the calculation of the volumes on the reference thermodynamic conditions is carried out using a temperature sensor with a resolution of 10 bits which provides a measurement in Kelvin degrees with a resolution of 0 25 C in a time span of 50ms The measurement of the gas temperature is acquired and updated every 30 s 4 5 Events and diagnostics With reference to the standards of the series UNI TS 11291 RSE implements
20. ding 0 F by sets of 4 as shown below BT 8 14 is et tof ejet7 ei sj4isi2i tio E es ee ee ee Example Diagnostics Hexadecimal encoding 0 8 0 2 Binary encoding 0000 1000 0000 0010 Meaning Bit 1 1 gt Metrological Event Log complete Bit 11 1 gt Dayligth saving time ora legale attiva 7 1 13 User Message Abbreviation MU Format Text 100 characters Unit Pressing enter Legal relevance NO User message information displayed pursuant to the provisions of the standard UNITS 11291 11 1 chapter 5 4 8 13 Date of issue Revision Revision date Page 22 of 32 04 06 2014 8 20 07 2015 oC Pietro RSE METER ENGLISH seas Use and Maintenance Manual Fiorentini PM Version 7 1 14 Redelivery Point PDR ID Abbreviation ID Format 14 digits Unit Pressing Enter E By pressing enter it is possible to scroll the 14 digits in both directions using the arrow keys Legal relevance Yes Redelivery Point PDR ID 7 1 15 Status of the valve Abbreviation SV Pressing Enter Press the central button to access the valve menu The menu structure is shown below To enter the password using the up and down buttons to select the numbers then press the enter button to confirm To perform the leak testing press the Enter button Here below there are all the submenus VAL 00 A Open valve 00 C Closed valve 00r Valve enabled to be opened VT number of attempis VP PSSD VP password ente
21. e ZVEI port 1 From the main SD menu press the central button to access the submenu ZVEI port status Disabled 2 Press the lower button once Submenu to enable the ZVEI port 3 Press the central button The operation was completed successfully 4 Press the upper button once ZVEI port status Enabled 5 Press the lower button twice Submenu to disable the ZVEI port Date of issue Revision Revision date Page 25 of 32 04 06 2014 8 20 07 2015 Pietro RSE METER ENGLISH seas Use and Maintenance Manual 6 Press the central button The operation was completed successfully 7 Press the upper button twice ZVEI port status disabled 7 1 16 2 Enabling and disabling of the counting for the test phase 1 From the main SD menu press the central button to access the submenu 2 Press the lower button three times The meter is counting with normal resolution 3 Press the lower button Menu to set the counting in high resolution 4 Press the central button The operation was completed successfully 5 Press the upper button The meter is counting with high resolution Date of issue Revision Revision date Page 26 of 32 04 06 2014 8 20 07 2015 Pietro RSE METER ENGLISH seas Use and Maintenance Manual 6 Press the lower button twice Menu to set the counting in low resolution 7 Press the central button The operation was completed successfully
22. eresne 23 Tides SEO CO N NO e E E N A E E E E E ENE 23 7 1 16 Status Ofthe CEVICE ec eecccsssssssseeeccccccsaessseeececccecssaeesseeeeceesssausueussseeeeeeessuauasseeeeeeeessaaaagssss 24 7 1 16 1 Enabling and disabling of the ZVEI port ccccccccssssecccesececeeecceeeeeeeceseeeecesseneceeeeneeeeeas 25 7 1 16 2 Enabling and disabling of the counting for the test Phase cccccesecccecesseceeeeseeeeeeeeeeeeeas 26 7 1 17 Maximum conventional flow rate ccccccccccccccccsseesesecccceesaeeeseseeeecccesssaeeseeeeeceseesauaaaeeeeeess 27 LLS een ee eee ee rece re een nee eee en ene eee ee ee eee ee 28 LL gece ener creer ne eee ree arse cnn eter nese Cree cere erent eee re ee ee eee cr ore 29 Pe 218 CTT 2 eee ene eee ne ae Tense ee ee ee eee 29 B AOA CUI OM meern E E E E A E E E E seaineeatgonrae 30 J Mamea a E A E E E E E 30 LE Ora N E enaa E E EA 30 9 1 1 Rao ene NE NSS rE ANE A E 30 9 1 2 PNN pO Ee EE E E E O 30 9 2 Devicereplacement and disposal iiiiz seis sepueditusan cpavecediaccesssbeteaiatolesavdenndecsnbindeasriatiesdiaaesesalteateaness 30 Date of issue Revision Revision date Page 3 of 32 04 06 2014 8 20 07 2015 RSE METER ENGLISH oc Pietro f OO aces es TaN se an aintenance manua 10 TCENNICAl CHALACICN SUC sccssessressar cn e Er a E NEN E EEEN EE aia Eni 31 10 1 Cenar Tee aA E A A E E E E 31 10 2 COMAN CaO DO S n aE E E E A E O A 32 32 10 3 Feeding devices Date of issue
23. f the normal resolution 00 operation not yet preformed 01 operation performed successfully 02 operation failed e Display of the read temperature Setting of the display contrast Press enter and then the up down keys to select the desired contrast value for the LCD display then press enter to confirm Reserved factory diagnostic b P Reserved factory diagnostic 00 o 02 03 PM1 affiliation status 00 PM1 off Waiting affiliation 01 Affiliation in progress 02 Affiliation failed 03 Affiliated 00 01 02 Start PM1 affiliation 00 ready to start Enter turns PM1 on if it is off and starts the affiliation 01 Affiliation in progress radio icon flashing 02 Affiliation already started Exit Press enter to close the maintenance menu and return to the main menu NO The menu 6 allows displaying the current status of the PM1 affiliation procedure menu 06 01 and the related enabling menu 06 02 by pressing the Enter key The procedure allows turning on the PM1 radio section and simultaneously initiating the affiliation proceedings SND IR The procedure can be restarted until a confirmation message is received for the first time CNF IR oO oO oO O O oo NO id N Legal relevance Date of issue Revision Revision date Page 24 of 32 04 06 2014 8 20 07 2015 Er Pietro RSE METER ENGLISH seas Use and Maintenance Manual Fiorentini PM Version 7 1 16 1 Enabling and disabling of th
24. h temperatures T Resistance to high temperatures EN 1359 1998 A1 2006 paragraph 6 5 5 Atex Ex ic 3G IIB T3 Gc MID Metrological battery Type 3 6 V lithium battery Format Size C Autonomy gt 15 years Transmission battery Type 3 6 V lithium battery Format Size C Autonomy gt 15 years Data memory Type EEPROM 12 Kbyte Data memory gt 20 years Real Time Clock RTC always active Accuracy according to EN62054 21 Accuracy class 1 5 1 According to MID Operating conditions Ambient temperature Ta min 25 C Flow rate Max Use of user interface 5 minutes per month Valve control 1 cycle per year Code update 2 every 15 years Date of issue Revision Revision date Page 31 of 32 04 06 2014 8 20 07 2015 oC Pietro RSE METER ENGLISH seas Use and Maintenance Manual Fiorentini PM Version 10 2 Communication ports Parameter Features Local communication port Physical level ZVEI IEC 62056 21 Speed 9600 baud Application level Protocol DLMS 10 3 Feeding devices RSE can ONLY be fed by a separate approved battery pack Metrological battery The feeding of the metrological equipment is guaranteed by a non rechargeable lithium battery with a duration gt 15 years under reference operating conditions see table below A single non rechargeable cell with Lithium Thionyl chloride technology Li SOClz is used The main features are Size C with Bobbin technology Rated voltage equal to 3 6 Vdc
25. h the provisions and regulations in force The manufacturer cannot be liable for damages resulting from failure to follow instructions and inappropriate use Safety warning All works must be performed by qualified personnel Transformation of spare parts Any technical changes are forbidden Use only original spare parts Transport As a rule meters shall be transported being kept in vertical position Upon receipt of the product examine the supplied material Immediately notify any shipping damage Storage As a rule meters have to be stored in vertical position and in a dry place at ambient temperature WARNING Install in a compartment that meets the provisions in force on safety away from any possible damage of mechanical origin away from sources of heat or open flames in a dry place and protected from external agents e Install with the indicator device in a horizontal position not in contact with the wall and raised with respect to the floor During installation avoid mechanical stress to the inlet and outlet connections e The arrow on the top of the meter indicates the direction of the gas flow e The on off valve positioned in the system upstream of the meter has to be opened in a gradual manner in order to make the gas flow homogeneously without violent shocks that could damage the internal components of the meter e It is strictly forbidden to repair or make any modifications to the instrument e The installa
26. he residual battery power is below the critical level In case of failure of the Gdm system The previously closed valve can be opened only locally by activating the keyboard according to a special procedure see chapter 4 1 1 The opening of the previously closed valve must be authorized in advance by the SAC Control Center It is possible to display the status of the valve in the related SV menu see chapter 6 and chapter 7 1 18 To reactivate a previously closed valve RSE must have first of all received the authorization for opening from the Control Center 4 1 1 Procedure for opening the valve through the user interface After receiving permission for opening the valve from SAC with a set time window useful to perform such operation and the maximum number of possible attempts under the SV valve menu the following will appear on the display VAL 40 r valve enabled to be opened Press ENTER to access the submenu Under the VP menu the message PSSD password requested appears press ENTER to enter the four digits of the password to be entered the operator must have the password Use the up and down buttons to select the digit to be set once the desired digit is displayed press ENTER to confirm it Repeat the same operation for all four digits After selecting the last digit and having pressed ENTER press again ENTER to start the opening of the valve At the end of the occurred opening the display shows the message
27. ice 2 3 Feeding devices RSE can be powered exclusively by a special approved battery pack As a matter of fat the battery pack is a proprietary assembly consisting of a lithium battery and a cable ending with a special connector coated by a protective sheath The battery pack is a device certified for exclusive use with the RSE device and it is the only permissible power supply device Caution Use only batteries of the type and model complying with the original The connector of the battery pack is polarized in such a way as to fit only in the connector specifically provided for on the device observing the correct polarity Date of issue Revision Revision date Page 7 of 32 04 06 2014 8 20 07 2015 Pietro RSE METER ENGLISH seas Use and Maintenance Manual Fiorentini PM Version The following data are given on the battery pack e Model e Maximum output levels e Week and year of production e Quality pass upon acceptance The metrological battery pack is sufficient to assure an autonomy of at least 15 years under the reference operating conditions specified in paragraph Technical features The transmission battery pack for the 169 MHz radio module is sufficient to assure an autonomy of at least 15 years under the reference operating conditions specified in paragraph Technical features 2 4 Safety instructions for installation in the hazardous area This equipment has to be installed and operated in compliance wit
28. in particular the following services UNI TS 11291 1 4 3 9 Service Detection and reporting of anomalies UNI TS 11291 6 7 1 Functional Requirements Event Log UNI TS 11291 6 7 6 Functional Requirements Diagnostics and alarms 4 6 Activation With reference to the standards of the series UNI TS 11291 RSE implements in particular the following services UNI TS 11291 1 4 3 1 Service Synchronization UNI TS 11291 1 4 3 6 Service Software updating UNI TS 11291 1 4 3 8 Service Management and Maintenance of the infrastructure UNI TS 11291 6 7 3 Functional Requirements Programming UNI TS 11291 6 7 4 Functional Requirements Operations concerning commissioning and maintenance UNI TS 11291 6 7 5 Functional Requirements Clock 4 7 Communication RSE has two communication interfaces a local one and a remote one Local interface Optical port Infrared port complying with the standard EN 62056 21 it requires an external device ZVEI probe The protocol used for the ZVEI optical port is DLMS The asynchronous format and the speed of the optical port are set to the following values Speed 9600 baud format 1 start bit 8 data bit N no parity 1 stop bit The ZVEI optical port is normally off To enable it follow the instructions given in chapter 7 1 19 1 Remote interface WMbus modem Integrated in the device antenna included and not remotizable The WMbus modem including the antenna is integrated in the meter Date
29. ities of the device periodic and not Therefore the actual consumption of the battery is calculated according to the time elapsed the individual functions actually performed and the weight in terms of consumption When this estimate exceeds 90 of the value set as threshold the appropriate alarm event is generated Date of issue Revision Revision date Page 14 of 32 04 06 2014 8 20 07 2015 Er Pietro RSE METER ENGLISH seas Use and Maintenance Manual Fiorentini PM Version 5 4 Security and fraud prevention The solutions implemented on the RSE meter to assure the security comply with the requirement set forth by the standard UNI TS 11291 With reference to the standards of the series UNI TS 11291 RSE implements in particular the following services UNI TS 11291 1 4 3 2 Service Detection and reporting of fraud UNI TS 11291 1 4 3 10 Service Security Management UNI TS 11291 6 7 2 Functional Requirements Access RSE implements all security policies defined by the reference standards and in particular by UNI TS 11291 In detail Access to the electronics is not possible without removing the mechanical and metrological seal and without permanently damaging the metrological cover Access to the memory device is not possible without permanently and patently damaging the meter Access to the flow on off valve and the temperature sensor is not possible without permanently and patently damaging the meter Access to the me
30. ject to alarm in the current billing period ssesesseseeesesrrerssrrrsesrress 19 7 1 3 Totalizer of volumes for price range 1 in the current billing period essessessseeesesrreresrrrreseeress 20 7 1 4 Totalizer of volumes for price range 2 in the current billing period essssssesseeserrreresrrrresrrres 20 Tiled Totalizer of volumes for price range 3 in the current billing Period cc cc eecccceeeeseeeeeeeeees 20 7 1 6 Totalizer of volumes under reference conditions in the previous billing period 20 7 1 7 Totalizer of volumes subject to alarm in the previous billing period cc eeeccceeeseeeeeeeeeees 20 7 1 8 Totalizer of volumes for price range 1 in the previous billing Period cc ceecccsessseeeeeeeeees 21 7 1 9 Totalizer of volumes for price range 2 in the previous billing Period ceecccesssseeeeeeeeees 21 7 1 10 Totalizer of volumes for price range 3 in the previous billing period ccceeecceeeeeeeeeeeees 21 ALI Invoice dale aoa ncece ea cece ans cnees sic onsen a civeqaeeienwsnc aes ss cecatodinsayaveaeos aeons au dionesinecnasannaesesindaneeeenvoiecascey 21 fj hat Wa B Je 2d 90s aa a ee een eee ren en eee E ee een eet ee etre ae eee 22 7 14 15 User Message sescancsacesecsascsenesessincacencnusssanoaranavnevanaacsay oan AER R EREEREER 22 7 1 14 Redelivery Point PDR ID eesssssssssssersessrsnssrresresssernsrrrnsrersseensrresrtenserensrresrtesrtensrresrtesererne
31. l Health and Safety Requirements of the ATEX Directive are EN 60079 0 and EN 60079 11 This device is designed to comply with the requirements of the type of protection Ex ic IIA T3 Gc ambient temperature range 25 55 C and ATEX category II 3G 2 1 Electrostatic discharges This device is approved for installation in areas with low explosion risk risk only for short periods In these areas sparks produced from electrostatic discharges could generate explosions in extreme cases Although during normal operation there is no presence of dangerous potentials on the device the use of dissipative footwear and of a damp cloth gt 65 is recommended during the installation maintenance Further information can be found in CEI 50404 During the installation or use of this instrument it is advisable to take steps to assure protection against electrostatic discharges Pietro Fiorentini SpA denies all liabilities resulting from the risks and consequences caused by the non compliance with these provisions 2 2 Connecting to other devices There is no RSE connection with external devices RSE can connect using the ZVEI optical port to devices for the communication of data and commands useful for configuration and maintenance of the device RSE can connect using the GSM modem wireless radio port to local and or remote devices for the communication of the data and commands useful for configuration management and maintenance of the dev
32. na tow rate ee Dom OH mo o o 6 2 3 Units of measurement field or YY When a temperature value is displayed h When a flow rate value is displayed Used together with the icon Date of issue Revision Revision date Page 17 of 32 04 06 2014 8 20 07 2015 mg Pietro jokers seas Use and Maintenance Manual Fiorentini PM Version 6 2 4 Numeric field lt consists of 8 7 segment digits and gives the value associated with the displayed menu page 6 2 5 Icons and alarms field O Flashing 9 aocemnnnnte o Ganaralwarnin Active alarnh Alarm not active but previously recorded and not 3 yet displayed Low battery to be replaced eow pane residual charge lt 10 Temperature alarm AGive alanm Alarm not active but previously recorded and not p yet displayed Authentication required to access the a submenu functions a netate cotter ee ee Date of issue Revision Revision date Page 18 of 32 04 06 2014 8 20 07 2015 or Pietro RSE METER ENGLISH seas Use and Maintenance Manual Fiorentini PM Version 7 Menu structure This section shows the hierarchy of the pages making up the interface with the user Under normal operating conditions the display is completely off Pressing the green Enter key the display turns on and performs a test in which all segments and icons are lit simultaneously for three seconds At the end of the test the first page of the menu is displayed If not any key is
33. nance Manual Fiorentini PM Version 7 1 3 Totalizer of volumes for price range 1 in the current billing period TI Abbreviation T1 Format 5 integers and 3 decimals Unit m Pressing enter Legal relevance YES 7 1 4 Totalizer of volumes for price range 2 in the current billing period Abbreviation T2 Format 5 integers and 3 decimals Unit m Pressing enter Legal relevance YES 7 1 5 Totalizer of volumes for price range 3 in the current billing period Abbreviation T3 Format 5 integers and 3 decimals Unit m Pressing enter Legal relevance YES 7 1 6 Totalizer of volumes under reference conditions in the previous billing period T PRE nn H nn h g A LI LI LI LI LI m Abbreviation T PRE Format 5 integers and 3 decimals Unit m Pressing enter Legal relevance YES 7 1 7 Totalizer of volumes subject to alarm in the previous billing period Abbreviation TA PRE Format 5 integers and 3 decimals Unit m Pressing enter Legal relevance YES Date of issue Revision Revision date Page 20 of 32 04 06 2014 8 20 07 2015 oC Pietro RSE METER ENGLISH seas Use and Maintenance Manual Fiorentini PM Version 7 1 8 Totalizer of volumes for price range 1 in the previous billing period Abbreviation T1 PRE Format 5 integers and 3 decimals Unit m Pressing enter Legal relevance YES 7 1 9 Totalizer of volumes for price range 2 in the previous billing period Abbreviation T2 PRE
34. ons see paragraph 10 3 and therefore it is not necessary to replace it The 169 MHz transmission battery is sized to assure an autonomy of more than 15 years under normal environmental and operating conditions see paragraph 10 3 and therefore it is necessary to replace it 9 1 2 Firmware update In case of release of a new firmware version the notes that describe the changes made since the previous version are distributed The firmware update can easily be performed also remotely Contact Samgas for further details 9 2 Device replacement and disposal Upon removal if necessary the device has to be disposed of according to the regulations on the management of waste in force at the time of disposal On the current date the Italian Legislative Decree No 152 2006 as amended and integrated is in force in Italy Date of issue Revision Revision date Page 30 of 32 04 06 2014 8 20 07 2015 oC Pietro RSE METER ENGLISH seas Use and Maintenance Manual Fiorentini PM Version 10 Technical characteristics 10 1 General features Parameter Features Enclosure Main body Polycarbonate Transparent cover Polycarbonate Protection degree IP 55 Dimensions overall RSE 2001 LA Max 223 H x 190 L x 172 5 P RSE 2 4 Max 246 H x 341 5 L x 179 P Distance RSE 2001 LA 110 mm RSE 2 4 250 mm Type of gas Methane gas town gas propane and UNI EN 437 2003 butane gas from the first to the third family Resistance to hig
35. ring Up and down to select Enter to confirm VL leak testing and result dm3 Legal relevance NO Date of issue Revision Revision date Page 23 of 32 04 06 2014 8 20 07 2015 mg Pietro jokers seas Use and Maintenance Manual Fiorentini PM Version 7 1 16 Status of the device SD fl LI E Abbreviation SD Format 1 digit Possible values 2 production e 1 factory 0 device configured 1 device under maintenance e 3 device not configured Unit Pressing Enter E Pressing the central button access is granted to the maintenance menu The menu structure is shown below 2 decimal digits define the menu id 2 decimal digits define the operation id 2 decimal digits define the operation result To perform the maintenance test if allowed it is necessary to press the central button Here below there is a list of submenus menu id operation result Description 00 01 ZVEI port status 00 disabled 01 enabled 00 01 02 Enabling the ZVEI port 00 operation not yet preformed 01 operation performed successfully 02 operation failed 00 01 02 Disabling the ZVEI port 00 operation not yet preformed 01 operation performed successfully 02 operation failed 00 01 Counting resolution status 00 Normal resolution 01 Resolution subject to testing 00 01 02 Setting of the counting resolution 00 operation not yet preformed 01 operation performed successfully 02 operation failed 00 01 02 Setting o
36. that the utilities on the customer side are closed Slowly load the RSE meter with pressure If on the meter a piping for pressure measurement has been subsequently installed check the tightness of the related connection After leak testing slowly remove pressure to the RSE meter Once the tightness has been checked the meter is ready for use The meters of the company SAMGAS require no maintenance WARNING When the meter is disassembled it may contain a residual amount of gas Considering the danger of explosion it is necessary to take safety measures e g After disassembling the RSE meter clean it very well with an inert gas For transporting the meter with residual amounts of gas use a vehicle with an open or vented loading area 5 2 1 Using the ZVEI probe The ZVEI probe available as an option is equipped with magnetic coupling Place the probe in the provided groove on the front part of RSE with the cable facing downwards The magnet and the groove will retain the probe in place To enable the communication on the ZVEI optical port it is sufficient to let the display show the SD menu Date of issue Revision Revision date Page 13 of 32 04 06 2014 8 20 07 2015 oC Pietro RSE METER ENGLISH seas Use and Maintenance Manual Fiorentini PM Version 5 3 Power supply The RSE meter can be powered exclusively by batteries The metrological battery is dimensioned to assure the operation of RSE for at
37. tion removal and any works in general have to be performed by qualified personnel in compliance with the provisions in force concerning safety 3 General description Figures 3 and 4 illustrate the structure and the main parts of the device The device consists of A metal enclosure containing in it e The mechanics for measuring the volumes complying with that of the RS 2001 meter e The flow on off valve e The sensor for measuring gas temperature e The permanent memory device see paragraph 4 3 data recording A plastic enclosure containing in it e The electronic measurement and communication card e The battery batteries On the front of the plastic container there are e A segment and icon display e Three operator keys e Optical communication interface Date of issue Revision Revision date Page 8 of 32 04 06 2014 8 20 07 2015 wa Pietro iF Aai sean Use and Maintenance Manual Metal enclosure Plastic enclosure Fig 3 RSE 2001 LA View Metrological battery Radio transmission battery not replaceable PCB card GSM transmission battery RSE is a measuring instrument with accuracy class 1 5 or 1 upon request as defined in Directive 2004 22 EC MID RSE is able to count the amount of gas that has passed through the meter in different consumption ranges in relation to the time in which it was measured in compliance with the provisions of the resolution 631 2013 R GAS issued by AE
38. trological battery and to the non replaceable transmission battery is not possible without removing the mechanical and metrological seal and without permanently damaging the metrological cover Access to the replaceable communication battery is not possible without leaving a record of the event in the Metrological Log of the meter Using interface equipment usually available to the user it is only possible to read the data and it is not possible to perform any configuration The configurations that can be performed through the communication channels with which the device is equipped which can be carried out only by authorized personnel leave a track as they are stored in the relevant memory log Metrological Log Attempts to tamper with the proper functioning of the meter are detected and recorded in the Metrological Log Attempts to access the meter through the communication channels with which it is equipped by unauthorized personnel are detected and recorded in the Metrological Log The commands sent by external devices through the communication channels with which the device is equipped are verified in terms of the source authenticity The messages transmitted through the communication channels conveying sensitive information are all efficiently encrypted Attempts to access the meter through the communication channels made with wrong passwords or encryption keys are detected listed and made available to the control center
Download Pdf Manuals
Related Search