Home

NetComm V200 User Guide

1. 1 5 Your Broadband Connection Bandwidth Consideration In order to achieve good voice quality when using the V200 VoIP feature we recommend that you use the V200 on a broadband connection with an upstream speed of at least 128kpbs This should allow you to have two simultaneous VoIP calls with G 729 codec using the V200 with good voice quality The more bandwidth you have the better the quality Note If your broadband router modem handles the Internet traffic for your LAN network then the V200 voice quality might be affected when you are in heavy Internet usage If your router has QoS feature please enable and configure it to give V200 traffic high priority V200 also has its QoS feature please see section 5 2 for instructions on how to use it V200 VoIP Telephone Adaptor Router YML795 Rev1 Melkoni 16 Package Contents Your V200 package contains the following items e V200 VoIP Telephone Adaptor e 12VDC 1 5 Amps power supply d LS Weser dB RJ 11 ADSL Line connection cable RJ45 10 100 Ethernet cable nstallation CD containing the User Guide and Adobe Acrobat Reader Package Contents List and Quick Start Guide If any of the above items are damaged or missing please contact your dealer immediately 10 V200 VoIP Telephone Adaptor Router YML795 Rev1 MAIL 17 Front Panel LED Indicators LED Indicator Status Function WAN On The WAN link is established Off Ethernet link
2. MELLE Broadband Solutions User Guide Melton Contents VoIP Telephone Adaptor Router settings cese treten nter ret nai idnina Sm kan taie 4 Chapter 1 IntroduGcklOn cesi oce oap ettu eroe opa nea e petuo nrt etes eoru won mga eg taS Esa et ga Pie RR 5 1 1 Product OVERVIEW z ussssstocu tn nitent id aninda ce r UeME AU RE ETE IE NERO IrRIRE 5 1 2 zzdurg e M 6 1 3 AP PIIGAEOMN e EAA 8 1 4 System Minimum Req ulrements ux niania ianen i EEE 9 1 5 Your Broadband Connection Bandwidth Consideration eee 9 1 6 Package Contents e coe pecia extus asus te e nE N ts divas 10 1 7 Front Panel MED TIndicatoES s eaiueoenesc ur iet tro hene inini kamen titia dieu nn 11 1 8 Back Panel and WiNA essiri renan etie ete ta tee Eer Ooi DEP TIrFI CE rewent 12 1 9 Power p Boot and ReSQt iisicseee tre eren sauces catecacys are n epe Russa aia Rada Rad 12 Chapter 2 Quick Start iieri eese rers beu see esas hah tanus ua Ennii TK ES RPRRRRRESRATAKRR Eii 13 2 1 Before you Begin ii iron xi remettre ae has na RR ENA EEES NENS EE NEATE 13 2 2 Typical Network Connections for V200 cesses sssi ennemi hix eaxsa ERR Renan 14 2 3 Marre mee a OE E T EA 16 2 3 1 Cable Connections asoscssecs etes en decee ska rninu ona Rus Ex eena nE EEE iNES Ernia 16 2 3 2 Poweron your V200 and PG ricina stata anmien Steed Noc ute E ONNA 16 2 3 3 Connecting to V200 ui
3. NetMask The subnet mask of the IP network DHCP Server Select Enable if you use the V200 as a DHCP server Starting IP Address The first IP address of the address pool in the DHCP server The IP address should be in the same subnet as the V200 LAN IP address End IP Address The last IP address of the address pool in the DHCP server The IP address should be in the same subnet as the V200 LAN IP address Enter or select the parameters and then click on the Apply button to submit the settings A confirmation window will be displayed Click Yes to confirm the submission or click No to cancel them The Web configuration will be interrupted if the IP address is changed Use the new IP address to login again 30 V200 VoIP Telephone Adaptor Router YML795 Rev1 Melton Chapter 5 VoIP Setup 5 1 p i SIP The Session Initiation Protocol SIP is an Internet Engineering Task Force IETF standard protocol for initiating an interactive user session that involves multimedia elements such as video voice chat gaming and virtual reality The SIP is a request response protocol dealing with requests from clients and responses from servers It can establish multimedia sessions or Internet telephony calls and modify or terminate them Because the SIP supports name mapping and redirection services it makes it possible for users to initiate and receive communications and services from any location and for networks to identify the users wherev
4. Category mode only 3 Click the Network Connections icon 4 In the LAN or High Speed Internet window right click on the icon corresponding to your network interface card NIC and select Properties Often this icon is labelled Local Area Connection 5 The Local Area Connection dialog box displays with a list of currently installed network items Ensure that the check box to the left of the item labelled Internet Protocol TCP IP is checked Select Internet Protocol TCP IP and click on Properties 6 In the Internet Protocol TCP IP Properties dialog box click the radio button labelled Obtain an IP address automatically Also click the radio button labelled Obtain DNS server address automatically 7 Click OK twice to confirm your changes and close the Control Panel V200 VoIP Telephone Adaptor Router YML795 Rev1 Melton Windows 2000 PCs First check for the IP protocol and if necessary install it 1 In the Windows task bar click the Start button point to Settings and then click Con trol Panel N Double click the Network and Dial up Connections icon 3 In the Network and Dial up Connections window right click the Local Area Connec tion icon and then select Properties 4 In the Local Area Connection Properties dialog box select Internet Protocol TCP IP and then click Properties 5 In the Internet Protocol TCP IP Properties dialog box click the radio button labelled Obtain an IP address a
5. The Add phone number window is opened Fconfiguration g Stun v Phone Book Wf call Forward Wf Dial Plan Wii Add Phone Number User Name 03768 Speed Dial 123 IPv4 Addr 202 96 136 135 PortNo 5060 Display Name Enter the information and click the Add button You will be returned to the phone list window with the added number now displayed You can also modify or delete any entry by selecting the corresponding Select option and then clicking on the Modify or Delete buttons 36 V200 VoIP Telephone Adaptor Router YML795 Rev1 MEL 5 1 4 Call Forward Call Forward lists the configured call forward information The first page displays the current call forward list The V200 has two call forwarding entries which allows you to specify call forwarding for each SIP account configuration Stun W rhone Book W call Forward W Dial Plan X Phone Call Forward List Select Phone No User Name HOST PortNo Fwd Call Fwd Uncond Fwd Rings 1 630795 fwd pulver com 5060 Yes Yes 6 Oo 2 676485 fwd pulver com 5060 Yes No 6 Modify To modify the call forward list select the corresponding Select option and then click on the Modify button The Modify Call Forward window is opened Modify Call Forward Fwd Call YES z User Name o0755 Host Addr or Domain Name wdpuvercom Port No 5o60 Fwd Uncond NO CallForward Rings B 1 15 Modify Cancel Field Description Fwd Call Choose YES if you want calls to be for
6. 3 YML795 Rev1 MIL VoIP Telephone Adaptor Router settings WEB account User Name admin Password admin LAN port IP 192 168 30 1 4 V200 VoIP Telephone Adaptor Router YML795 Rev1 Melton Chapter 1 Introduction This chapter gives a brief introduction to the V200 VoIP Telephone Adaptor Router including a product overview description of the product features and its application 1 1 Product Overview The V200 has been designed for residential and small business users to deliver predictable real time voice quality over the Internet It connects directly to any broadband modem and service Cable or DSL which supports VoIP Two standard analogue telephones desktop or cordless can be connected to the Phone FXS ports on the back of the V200 allowing the user to route calls over the Internet to anywhere in the world using VoIP significantly reducing or eliminating long distance call charges To enhance your VoIP experience and simplify network integration the V200 is equipped with a 3 port Switch and Quality of Service QoS Router The V200 s QoS feature ensures you maintain high quality VoIP calls during periods of heavy Internet use by dynamically calculating and prioritising the required upstream bandwidth The V200 can be configured as a DHCP server for LAN and Network Address Translation NAT can be used to translate private addresses to public address In this way computers in the LAN do not require public IP addr
7. Default 3478 V200 VoIP Telephone Adaptor Router 35 YML795 Rev1 Melton 5 1 3 Phone Book The Phone Book should only be used in SIP non use Proxy mode With the Phone Book you do not need to subscribe to a VoIP service provider You will need to obtain the public IP address and SIP outbound address port of the SIP phone or ATA you wish to communicate with The first page displays the current phone list Below is a typical example oonfiguration g Stun W Prone Book Wf call Forward Dial Plan Y Peer To Peer Contacts Note This phone book only works when your V200 configured in non proxy mode Select User Name Speed Dial HOST Port No Display Name Oo 03768 123 202 96 136 135 5060 Kirstin Field Description User Name User name of the person e g Kirstin that you want to reach And the remote party must use this user name to accept incoming call Speed Dial A speed dial number Whenever dialling 123 using your V200 you will be connecting to the Destination IP address on the specified port Host The host IP address to call Port No The port number on which destination party listens your V200 SIP requests Display Name The name displayed to the person you are calling You will need to ask the person you are calling to configure their Internet device Modem Router to allow connections on the specified port to be forwarded to their SIP phone or ATA To add a new phone number to the phone book click the Add button
8. LAN is a data communications system that lies within a limited spatial area has a specific user group and has a specific topology Light Emitting Diode A light or status indicator Media Access Control address The unique fixed address of a piece of hardware normally set at the time of manufacture and used in PAT protocols Medium Access Control a protocol for determining which device has access to the network at any one time Megabits per second One megabit is 1 048 576 10242 bits Media Gateway Control Protocol is a protocol used within a VoIP system Network Address Translation is a transparent routing function that translates a Private IP address on a PAT into a Public address that can be used in a public network The network portion of an IP address Network protocols encapsulate and forward data packets from one interface to another Unwanted interference to a transmitted signal by an outside source Password Authentication Protocol PPP protocol that ensures authentication of the connection between two devices Port Address Translation is a form of NAT that maps multiple Private IP addresses to a single Public IP address An Internet utility signal sent to check the accessibility of a device automatically without requiring the user to turn off the system during installation Any connection with only two endpoints A dedicated data link that connects only two stations An access point where data can e
9. Please refer to the User Manual of your ADSL modem router for instructions on how to set this up RJ11 telephone cable 845 network cable Telephone Socket Analogue Telephone Broadband Modem V200 VoIP Telephone Adaptor Router Analogue Telephone Note The WAN port mode in this diagram can be either in PPPoE or Static IP assign a public IP mode V200 VoIP Telephone Adaptor Router 41 YML795 Rev1 MILI Routing Internet Traffic for your LAN Network When your V200 WAN interface is assigned with a Public IP either through static WAN IP or PPPoE it actually does the routing for your Internet connection When you configure QoS you need to specify your ADSL true upstream bandwidth It might be 64 128 256 or 512 If you are not sure about this parameter please consult your ADSL Internet service provider Click VoIP QoS in the menu bar to bring up the QoS configuration window VoIP QOS Configuration Current Status Disable The Link Speed of Up Stream 128 Kbps VoIP Qos Enable z Apply The link speed of Up Stream is in the unit of Kbps type in your ADSL true upstream speed value and click on the Apply button to submit the settings That s all there is to it QoS for VoIP calls is now enabled 42 V200 VoIP Telephone Adaptor Router YML795 Rev1 MEL Chapter 6 Additional Routing Features This chapter describes the use and configuration of the additional Routing features suppor
10. RP xx mre Rd Ro xis Seria 43 6 1 NAT Port Forwarditig 5 seus cionem sner errant aka epu ea SEEEN iE ETE 43 6 2 p p 44 6 3 Access Control isos ieiuna tna edsirancmenedsananenansesaced Ka PY RF Sa a a aN 45 6 4 REMOLE ACCESS sss xavkiuedie pus rd webs E UNDIS AUDI EALESKUE FEE ad hr SU e da sien 46 Chapter 7 V200 System Information 12e herren euin cae enea a araisa Eia 47 7 1 ic o 47 7 2 Nisier iu urjde mr 48 732 1 Inrtebface StatistiCS succes eroe tali bbs Ad ei aversos ocui ex Du ROPA ERNR ARRA OR UE 48 v Mer vashoededacte Bawa aaa esa A tulsa E A 49 2 V200 VoIP Telephone Adaptor Router YML795 Rev1 MEL 72 3 DHCP LGedSe sisi tnit sistas cemebies Fbbas ceca Eni aa S oPudH UU nS RE PAM E MPRUAA Ue eia 50 7 3 Pil TELE QI ID LLL OLI DIDI UBI 51 7 4 LEE 52 7 5 RESOU sauce secon uio etenim ud OUIR Ta auta ine MMRUSS ENDO CR tau shiae aate UR PATE d DCUM E 53 7 6 Merl ET 54 7 7 Rebooting the System ciini etes ere np RR RI Kem ka esai uir ra TER E RR ER ERR YR 55 Appendix A Cable Information u cucc eerta ot tnr rhet rate tet tutem dino RE CRM eR RR RR Era n Ennis 56 Appendix B GlosSary iier tegere recense enne rmx xut bein pbe se sau ud ieu a aa dro go tile idR 58 Appendix C Registration and Warranty Information sss 63 V200 VoIP Telephone Adaptor Router
11. Status Registered Success Register Status Registered Success Qvalue Codec Payload Type 0 8 G729 101 Client Expire 60 RTP packet interval 20 DTMF in band MaxDigist 24 Port No 5060 Internal Call Yes Proxy Register Domain Proxy fwd pulver com Domain fwd pulver com WAN WAN MODE DHCP mode WAN IP Address 192 168 1 11 Subnet Mask 255 255 255 0 Default Gateway 192 168 1 253 STUN Current State Enable STUN Server stun fwdnet net V200 VoIP Telephone Adaptor Router YML795 Rev1 MaxRings 15 UseProxy YES RTP Port 16384 Port 5060 Current State Active Primary DNS Server 192 168 1 253 Secondry DNS Server 4 2 2 2 Port No 3478 47 MILI 7 2 Traffic Statistics The Traffic Statistics menu will display detailed information on the V200 s LAN amp WAN Interface TCP IP settings and DHCP client leased information 7 2 1 Interface Statistics Interfaces is the first page of the Traffic Statistics window Web Configuration Configuration Microsoft Internet Explorer File Edit View Favorites Tools Help Back gt O A A Reach Gyravorites media C B 5 Address http 192 168 30 1 Remote Access Status zigixi Interfaces Interface Statistics Admin Status ois Unicast Broadcast EE Errors Octets Unicast Broadcast ESRB Eats In In Out In PktsIn PktsIn In Out PktsOut PktsOut O
12. bring up the Upgrade screen ini x F Web Configuration Configuration Microsoft Internet Explorer E P File Edit View Favorites Tools Help Se as Back gt 2 Qsearch xgjFevortes Ameda C Ey S Address http 192 168 0 1 z CG inis Qr p NAT Port Forwarding DMZ Access Control Upgrade Remote Access Locate the firmware on your local hard drive by clicking the Browse button below Status File Name C Documents and Set _ Browse Traffic Statistics Ping Please do not reboot until instructed to do so Use the Browse button to locate the software and then click on the Upgrade button A window will display the upgrade process On successful completion of the firmware upgrade the following screen will be displayed Upgrade Firmware Upgraded Successfully Reboot Click on the Reboot button to save the changes and reboot your V200 54 V200 VoIP Telephone Adaptor Router YML795 Rev1 MAI 7 Rebooting the System It may be necessary to reboot the V200 Ensure that you have saved any changes to the system setting of the V200 Please note that any customised configuration settings will be lost if you proceed with this function without saving the changes refer to the section on the Save menu Click the Reboot menu item in the menu bar on the left to bring up the Reboot screen Click on the Reboot button to reboot the V200 Zh Web Configuration Configuration M
13. registration authentication Device Ports 1 WAN port RJ 45 IEEE 802 3 10 100 Base T Auto crossing for easy connection 3 LAN port RJ 45 IEEE 802 3 10 100 Base T for LAN switch 2FXS RJ 11 for connection to analog telephone Note The availability of some listed call features is dependent on the service supported by your VoIP service provider Please consult them for further information V200 VoIP Telephone Adaptor Router 7 YML795 Rev1 PM 13 Application Please refer to the following diagram for a typical application of the V200 Figure 1 illustrates a simplified connection for the V200 In addition to providing basic VoIP calls the V200 provides you with normal VoIP and router switch capabilities so it can work as a router and a VoIP ATA analog telephone adapter at the same time ees RJ11 telephone cable 845 network cable Telephone Socket Analogue Telephone V200 VoIP Telephone Adaptor Router Analogue Telephone Figure 1 8 V200 VoIP Telephone Adaptor Router YML795 Rev1 Melton 14 System Minimum Requirements A valid SIP VoIP account from a VoIP Service Provider A Broadband service A Broadband Modem Router bridge mode capable An Analog telephone with RJ11 line cord Desktop Cordless or Dect A PC with Web browsing application for V200 configuration only Note In some cases you may need to configure your broadband router in bridge mode The V200 will perform routing on your network
14. this menu Click the Access Control menu item in the menu bar on the left to change your password for the V200 s Web log in Web Configuration Configuration Microsoft Internet Explorer Fie Edit View Favorites Tools Help Back gt O A Gt Qsearch 3gFavortes dijMeda B H Address http 192 168 30 1 VoIP OO Ge wis Gsneat ts p Change Password NAT Port Forwarding DMZ Old Password Access Control New Password Remote Access Confirm New Password soar Status Teaffin Ctatictine Type the old password and then type the new password twice Click on the Apply button to submit the settings Note If you change the password make sure you keep a record of it in a safe place as you will require it the next time you log on V200 VoIP Telephone Adaptor Router 45 YML795 Rev1 Melton 6 4 Remote Access To manage the V200 via a web browser you do not have to login from a PC directly connected to the V200 With the Remote Access feature you can login through the Internet from anywhere if you know the public WAN IP address of the V200 This feature is only available if you connect your V200 and configure your network in 1 Basic ADSL Router connection with the Router in Bridge mode or 2 A Cable connection with no Router between the cable modem and the V200 Just type in the WAN public IP address in the address bar of your web browser and you can login into V200 remotely thr
15. 0 during the boot up as this may cause unexpected results or even damage the V200 Reset Reset reloads the V200 to its factory default settings After the V200 has completely booted up use a small object like a ballpoint pen to press the button and hold it down for over three seconds The V200 will reset and all its parameters will return to their factory default settings Then the V200 will reboot automatically You can also reset the V200 in the Reset menu of its Web configuration page 12 V200 VoIP Telephone Adaptor Router YML795 Rev1 D Ll gll Chapter 2 Quick Start 24 Before you begin You will need to collect your VoIP account details before you start to configure your V200 Details should include your SIP username VoIP number your SIP account authentication ID and its password SIP proxy server IP URL your VoIP network preferred codec and whether you need use STUN When you open a VoIP account your VoIP provider should provide you with this information Please try to complete the following information before you start your V200 setup VoIP phone number also known as SIP username VoIP account authentication ID VoIP account authentication password SIP server IP URL SIP server domain name SIP server port VoIP codec VoIP DTMF transport method Traversing firewall method V200 VoIP Telephone Adaptor Router 13 YML795 Rev1 Melton 2 2 14 Typical Network Connections for V200 The Quick Start sectio
16. 8 Errors Destination Unreaches 178 Time Exceeds 0 Source Quenches 0 Redirects 0 Echos 6 Echo Replys 4 OUT Messages 13 Errors 0 Destination Unreaches 7 Time Exceeds 0 Source Quenches 0 Redirects 0 Echos o Echo Replys 6 V200 VoIP Telephone Adaptor Router 49 YML795 Rev1 MAIL 7 2 3 DHCP Lease DHCP Lease page displays information regarding MAC Address mapping to Lease IP DHCP Lease Statistics Lease IP 192 168 30 3 MAC Address 00 00 e2 9d 28 fc 50 YML795 Rev1 V200 VoIP Telephone Adaptor Router MEL 73 Ping A Ping test is used to verify the status of a network connection Ping sends a request message to the host and waits for a return message This function can verify if the remote host is reachable Ping can also measure the round trip time to the remote host Click the Ping menu item in the menu bar on the left to bring up the Ping screen Web Configuration Configuration Microsoft Internet Explorer 0 x File Edit View Favorites Tools Help ES Back gt O S A Reach GFavortes meda G D 5 Address heepyjis 168 90 1f NT unis Osnat ps Status Ping Traffic Statistics Host Name or IP Address stun fwdnet net Enter the Host Name or IP address of the remote terminal and click on the Submit button to start the ping The results are displayed The following is an example of the ping result Host is alive Ping Statistics i
17. 95 Rev1 MAIL 6 2 44 DMZ A DMZ allows a single computer on your LAN to expose ALL of its ports to the Internet By doing this the exposed computer is no longer behind the NAT firewall DMZ is far easier to set up than port forwarding in terms of setting up a virtual server but it exposes your entire computer to the Internet Note Sometimes TCP IP applications require very specialized IP configurations that are difficult to set up In this case placing your computer in the DMZ is the only way to get the application working Following is an example of DMZ which redirects all of low ports on WAN interface to a host with internal IP address 192 168 30 143 Click the DMZ menu item in the menu bar on the left to display the current DMZ configuration setting Web Configuration Configuration Microsoft Internet Explorer ni xi File Edit View Favorites Tools Help Heak gt OA A Aseh Haravortes Greda Eb 3 Address http 192 168 30 1 e inks Osnat ts VoIP UO E 4 DMZ Configuration NAT Port Forwarding DMZ pz Enable Access Control IP address REEEEEETEEE Remote Access Css caves Status Traffic Statistics al You can decide to Enable or Disable DMZ Enter the internal IP address if DMZ is enabled Then click the Apply button to submit the setting V200 VoIP Telephone Adaptor Router YML795 Rev1 MAI 6 3 Access Control You can change your password in
18. Header The beginning of a frame or cell that contains management and addressing information Hop One point to point transmission in a series required to transmit a message between two hosts in a network Host An addressable computer connected to a network Hub A device that serves as the central location for attaching wires form workstations H 323 The ITU International Telecommunication Union standard which defines how audio visual conferencing data is sent across any packet network ICMP Internet Control Management Protocol An Internet protocol that allows for the generation of error messages tests packets and information messages related to IP IEEE Institute of Electrical and Electronics Engineers IEEE The Institute of Electrical and Electronics Engineers IP address Internet Protocol address The decimal numeric fixed length address assigned to an Internet host IRQ Interrupt re quest a hardware interrupt on a PC ISO International Standards Organization V200 VoIP Telephone Adaptor Router 59 Melton Kbps LAN LED MAC address MAC Mbps MGCP NAT Network address Network protocol Noise PAP PAT Ping Point to point connection Port POTS PPP 60 YML795 Rev1 Internet Service Provider An organization that provides access to the Internet Literally it means Kilobits per second but usually it is taken to mean 1 024 bits per second Local Area Network A
19. LLLLLLI Normal Assignment Input Receive Data Input Receive Data Output Transmit Data Output Transmit Data Not used Figure 1 RJ 45 plug attached to cable Figure 2 V200 VoIP Telephone Adaptor Router MEL Straight and crossover cable configuration There are two types of the wiring Straight Through Cables and Crossover Cables Category 5 UTP STP cable has eight wires inside the sheath The wires form four pairs Straight Through Cables has same pinouts at both ends while Crossover Cables has a different pin arrangement at each end In a straight through cable wires 1 2 3 4 5 6 7 and 8 at one end of the cable are still wires 1 8 at the other end In a crossover cable the wires of 1 2 3 6 are reversed so that wire 1 become 3 at the other end of the cable 2 becomes 6 and so forth To determine which wire is wire 1 hold the RJ 45 cable tip with the spring clip facing towards the ground and the end pointing away from you The copper wires exposed upwards to your view The first wire on the far left is wire 1 You can also refer to the illustrations and charts of the internal wiring on the following page Straight Through Cabling Y UN Figure 3 Wire Becomes 1 1 2 2 3 3 6 6 Figure 4 Wire Becomes 1 3 2 6 3 1 6 2 Note To prevent loss of signal make sure that the length of any twisted pair connection does not exceed 100 metres V200 VoIP Telephone Adapt
20. an configure the WAN and LAN interface settings 41 WAN Setup Click on the WAN Setup menu item from the menu bar to bring up the WAN Status window The WAN IP address information will be displayed The following screen is an example which shows the V200 s WAN port is in PPPoE mode and currently active WAN STATUS WAN MODE PPPoE mode Current State Active WAN IP Address 220 240 6 225 Subnet Mask 255 255 255 0 Default Gateway 203 194 30 180 Primary DNS Server 203 194 56 150 Secondry DNS Server 203 194 27 58 WAN Setup Field Description WAN IP address The WAN IP address Subnet Mask The subnet mask of this network Default Gateway The gateway IP address of this network Primary DNS Server The primary DNS server IP address Secondary DNS Server The secondary DNS server IP address that will be used in the event that the primary server IP address fails or is not available To set up WAN click the WAN Setup button and the following information will be displayed V200 VoIP Telephone Adaptor Router 25 YML795 Rev1 Melton WAN SETUP Select WAN MODE C Static IP address C DHCP mode PPPoE mode _Next Cancel Select a WAN connection type and then click on the Next button Field Description Static IP address A static IP address it can be a static LAN IP address or public IP address If you will use static public IP address and are using ADSL broadband you can enable the V200 QoS feature whi
21. ch will maintain VoIP call quality even in periods of heavy Internet usage DHCP mode Obtain an IP address via DHCP protocol PPPoE mode PPPoE is often used in ADSL environment Your ISP will assign you IP address via PPPoE protocol 26 V200 VoIP Telephone Adaptor Router YML795 Rev1 MEL 4 1 1 Static IP address Select the Static IP address option and click on the Next button to display the following window WAN SETUP Static IP Address WAN IP Address 220 240 6 225 Subnet Mask 255 255 255 0 Default Gateway 203 194 30 180 Primary DNS Server 203 194 56 150 Secondry DNS Server 203 194 27 58 Apply Cancel Field Description WAN IP address The WAN IP address Subnet Mask The subnet mask of this network Default Gateway The gateway IP address of this network Primary DNS Server The primary DNS server IP address Secondary DNS Server The secondary DNS server IP address that will be used in the event that the primary server IP address fails or is not available Enter the necessary parameters and click the Apply button to submit the settings V200 VoIP Telephone Adaptor Router 27 YML795 Rev1 MAIL 4 1 2 DHCP Mode Select the DHCP Mode option and click on the Next button to display the following window WAN SETUP Click YES to Start DHCP client Click NO to Return Click the YES button to enable your V200 as a DHCP client 28 V200 VoIP Telephone Adaptor Router YML795 Re
22. cluded This warranty is in addition to and not in replacement for such conditions and warranties To the extent permitted by the Relevant Acts in relation to your product and any other materials provided with the product the Goods the liability of NetComm under the Relevant Acts is limited at the option of NetComm to 64 Replacement of the Goods or Repair of the Goods or Payment of the cost of replacing the Goods or Payment of the cost of having the Goods repaired V200 VoIP Telephone Adaptor Router YML795 Rev1 9 NETCOMM LIMITED Asn 85 002 490 486 IH 7 PO Box 1200 Lane Cove NSW 2066 Australia P 02 9424 2070 F 02 9424 2010 Broadband Solutions E sales netcomm com au W www netcomm com au
23. communicate with the SIP server or remote end This port can be changed Default 5060 UseProxy In order to use the V200 with a VoIP service provider you will need to specify a Proxy server which the V200 communicates with Choose Yes and enter the details under the Proxy Register and Domain sections Choose No if you want to use the V200 in Peer to Peer mode 32 V200 VoIP Telephone Adaptor Router YML795 Rev1 MIL Field Description The base RTP port of V200 The real range of V200 RTP port is Base Port Base Port 7 8 ports in total For example by specifying 16384 here the real RTP port range will be 16384 16391 RTP Port The Internal Call Note The Internal Call option allows you to specify how the V200 handles calls between Phone 1 and Phone 2 when they have separate VoIP accounts By default this feature is enabled and allows you to route the calls locally between Phonel and Phone 2 In this case there is no traffic going through to the Internet If disabled calls between Phonel and Phone2 will be routed by your VoIP providers SIP server You must configure Account 1 and Account 2 before you can use the internal call feature That means both Account 1 and Account 2 need to have a VoIP account information entered In terms of the internal call there is an alias for Account 1 and Account 2 To make internal calls just simply dial and the other phone will ring Proxy Register Host Addre
24. d number meets the Prefix the V200 will modify the dialled number before dialling it If the dialled number does not meet the Prefix the V200 will dial the number without any modification The first page displays current dial plan Dial Plan List Select Prefix Mini_digit Max digit Delete digit Insert digit C 00 10 22 2 0011 Add Modify Delete To add a new entry in the Dial Plan click the Add button The Add Dial Plan window is opened Add Dial Plan Prefix b Mini digit 10 Max digit ze Delete digit 2 Insert digit boar Add Cancel Field Description Prefix The prefix number that needs to be modified for Dial Plan Mini_digit Minimum length of the dialled number that must be equal to or greater than the Prefix number Max digit Maximum length of the dialled number If the length of the dialled number is greater than this value the digits over this value will be eliminated Delete digit The number of digits that need to be eliminated before dialling The eliminated digits begin at the first digit of the dialled number Insert digit The digits that need to replace the deleted number Above window shows Kirstin s first dialling method in her Dial Plan Kirstin just come Australia from UK The international call number in UK is 00 With the V200 she does not have to change it into 0011 In above dial plan configuration whenever she dials 00XXYYYYYY the output i
25. de Current State Active WAN IP Address 192 168 1 11 Primary DNS Server 192 168 1 253 Subnet Mask 255 255 255 0 Secondry DNS Server 4 2 2 2 Default Gateway 192 168 1 253 STUN Current State Disable STUN Server Port No 3478 V200 VoIP Telephone Adaptor Router YML795 Rev1 19 MALUM B Select V200 WAN port type Click on WAN Setup menu item from the menu bar on the left hand side to bring up the WAN Setup window h WAN SETUP Select WAN MODE C Static IP address DHCP mode PPPoE mode Next Cancel By default the WAN port is setup to operate in DHCP mode This will work with a typical ADSL or cable broadband network as shown in Figures 2 amp 3 The following screen shot is an example of the V200 in DHCP mode R WAN STATUS WAN MODE DHCP mode Current State Active WAN IP Address 192 168 1 10 Subnet Mask 255 255 255 0 Default Gateway 192 168 1 253 Primary DNS Server 192 168 1 253 Secondry DNS Server 210 0 111 111 WAN Setup If you are using a cable broadband service you can simply use the V200 WAN port default setting as DHCP 20 V200 VoIP Telephone Adaptor Router YML795 Rev1 MAIL C Configure V200 SIP On the V200 Configuration page click the SIP button will bring a SIP configuration page The following screen shows you an example of SIP configuration of the V200 which will allow the V200 to use 630801 and 683752 as its VoIP phone number and authenticati
26. er they are Configuration You can configure SIP parameters in Configuration window The figure below shows you an example of a SIP account configuration There are two VoIP accounts in this page Account 1 and Account 2 which represent Phonel and Phone2 respectively By default the Phone 2 Account 2 is disabled So if you only have one SIP account you can simply configure the account in Phone 1 Account 1 and leave the Account 2 disabled as its default If you have two accounts you need to enable Account 2 before you configure it Lu A Stun W Prone Book WF cou Forward WP Dial Plan WH Account2 Enable v Phone Number 683752 Display Number NetCommV200 Account1 Phone Number 630801 Display Number NetCommV200 Auth ID 630801 Auth ID 683752 Auth Password ee Auth Password essees Confirm Password Confirm Password eeeeee Proxy Register Domain Host Address URL Domain Address fwd pulver com fwd pulver com Port No Client Expire 60 QValue 0 8 RTP packet interval 20 Codec 6729 DTMF in band Payload Type 101 MaxDigist 24 MaxRings 15 Port No 5060 UseProxy Yes Internal Call YES RTP Port 16384 5060 Field Description Client Phone Number Display Name V200 VoIP Telephone Adaptor Router YML795 Rev1 The phone number used for your V200 to register on a SIP s
27. erver What the call party see when you call them 31 MEM Auth ID The authentication username assigned by your VoIP service provider This can be a different number to your VoIP number Auth Password The authentication password assigned by your VoIP service provider Confirm Password Repeat the password Expire Duration of interval for SIP keep alive registration Default 60 QValue The priority assigned to the V200 to register on the SIP server of your VoIP service provider The value must be between 0 and 1 with 1 having the highest priority Default 0 8 RTP packet interval Duration frequency of the V200 sending compressed voice data packet There are two options for this setting 20ms and 40ms In some cases a 40ms interval can save your broadband upstream bandwidth comparable to a 20ms interval For the best value for this setting please consult your VoIP service provider Codec G 729 is the highest compression codec which only occupies 8kbits sec PCMA G 711 alaw and PCMU G 711 ulaw quire 64kbits sec We highly recommended you to use G 729 Default G 729 DTMF In band or RFC 2833 Default in band Payload Type It indicates which RTP packets contain DTMF information in normal RTP stream MaxDigist The maximum number of digits numbers you can dial using the V200 Default 24 MaxRings The number of rings before an incoming call is answered Maximum 24 Default 15 Port No The port on the host used to
28. eset This function allows you to reset your V200 back to the factory default settings Please note that any customised configuration settings will be lost if you proceed with this function We recommend that you take a note of your settings before you proceed The default settings will take effect after the system reboots Click the Reset menu item in the menu bar on the left to bring up the reset screen and then click on the Reset button File Edt View Favorites Tools He EJ Back gt O A A Asearch Favorites Ameda C D S Address E mpqnezieosnn Sh ee wis Gest E DMZ z 5 Access Control Remote Access The current parameters will be erased from the flash and Status reset to their original default settings T This will come into effect after reboot Traffic Statistics Ping Save Reset Reset Upgrade Reboot al V200 VoIP Telephone Adaptor Router 53 YML795 Rev1 Melton 7 6 Upgrade This function allows you to Upgrade your V200 s firmware Please note that any customised configuration settings will be lost if you proceed with this function We recommend that you take a note of your settings before you proceed From time to time new Upgrade firmware may become available from NetComm s web site Download the appropriate file to your PC and note the location into which you have saved the file Click the Upgrade menu item in the menu bar on the left to
29. esses in order to access the Internet V200 VoIP Telephone Adaptor Router 5 YML795 Rev1 Melton 1 2 6 Features VolP Protocol Support Session Initiation Protocol SIP Session Description Protocol SDP Transport Protocol for Real Time Applications RTP VoIP Audio Codec e G 729a e G 711 alaw e G 711 ulaw DTMF Relay n band Out band RFC 2833 Voice Features Echo Cancellation G 168 Voice Activity Detection VAD Comfort Noise Generation CNG Silence Suppression Jitter Buffer Adjustable RTP packetization interval Telephone Function Support Caller ID On Off hook Caller ID ETSI based DTMF tone generation Dialtone Busy tone Ring back tone generation QoS Internal bandwidth control Allocating enough bandwidth for VoIP calls VoIP Call types e SIP proxy Phone Book for Peer to Peer IP Call Built in Router DHCP client server NAT Port Forwarding DMZ e Virtual Server YML795 Rev1 V200 VoIP Telephone Adaptor Router MEL VoIP call functions Call Transfer Call Waiting Call Hold Resume Call Forward e Call Switch e CFU Call Forward Unconditional CFB Call Forward Busy WAN Protocol Support DHCP client Static IP PPP over Ethernet client Internet Support IP TCP UDP ICMP ARP protocols HTTP DNS VPN Support IPSec and PPTP pass through Security PAP CHAP for PPPoE authentication e MDS for SIP
30. f the V200 is connected to your PC using a RJ45 cable 2 3 2 Power on your V200 and PC Make sure all cables are connected properly and then power on the V200 It will take approximately 1 to 2 minutes for the V200 to boot up After the V200 is completely booted up switch on your PC which is directly connect to V200 via its LAN port This PC is only required for V200 configuration period 2 3 3 Connecting to V200 16 The purpose of this section is to provide instructions on how to assign an IP address to your PC When the PC completely boots up it might already be able to talk to the V200 You can check it using Ping utility If the connectivity is OK you can skip this section and jump to Section 2 3 4 This section are only required if you are having trouble accessing your V200 HINT To test the network connectivity between the PC and the V200 you can open a DOS prompt Start gt Run gt cmd and execute coming ping 192 168 30 1 Once you receive a reply from the V200 you know that the PC and talk to the V200 The Please ensure your PC is setup as DHCP client mode in which the V200 will assign a valid IP address to your PC and allow it can communicate with your V200 The following section provides instructions on how to set this up with different Windows Operating Systems Windows XP PCs 1 In the Windows task bar click the Start button and then click Control Panel 2 Click on Network amp Internet Connections icon
31. for the WAN port is not established Flash Data transmitting or receiving over WAN LAN1 LAN3 On Ethernet link for LAN port is established Off Ethernet link for a LAN port is not established Flash Data transmitting or receiving over LAN Phone1 2 On Phone is off hook and being used Off Phone is not being used Flash VoIP call is coming POWER On Power is supplied Off Power is not supplied YML795 Rev1 Melton 1 8 Back Panel and Wiring Label Description Reset Press button to restore the configuration to its factory state WAN Connect to your ADSL modem LAN port with an RJ45 connector cable Phone 1 2 Connect to one or two phones with an RJ11 connector cable LAN Connect to your PCs Ethernet ports or a hub switch with RJ45 connector cables Power Connect to the power adapter and then plug the power adapter into the wall outlet 19 Power up Boot and Reset Please only power up your V200 after all cables are connected The POWER LED should always be on after the V200 has powered up Once the power is on the V200 will boot up automatically Do not do anything until the boot up process has completed Boot or reboot During the booting period all of the LEDs except for the POWER LED will flash irregularly This is part of the normal process All LEDs should be stabilized after the V200 has completely booted up on off or regular flashing The whole booting procedure takes about 1 5 minutes Do not do anything to the V20
32. g Information Protocol The protocol governing the exchange of routing information A 6 position jack used with dial networks and telephone sets An 8 position jack used with programmable dial networks Protocol dependent device that connects subnets together Routers operate at the network layer layer 3 of the ISO Open Systems Interconnection Reference Model A table that lists routing paths to enable a node to route traffic to another node in the network A low speed 25 position DCE DTE interface Hardware or software that offers a specific service such as database management to a client Session Initiation Protocol a signaling protocol for Internet conferencing telephony A route that is permanent rather than a route that is dynamically assigned by another router STP Shielded Twisted Pair Telephone wire that is wrapped in a sheath to eliminate external interference V200 VoIP Telephone Adaptor Router 61 YML795 Rev1 Melton Subnet address Subnet mask Subnet Switch TCP IP TCP Telnet Throughput UDP Upload URL VPN WAN 62 YML795 Rev1 Simple Traversal of UDP User Datagram Protocol through NAT Network Address Translation The subnet portion of an IP address A number that identifies the subnet portion of a network address so that IP addresses can be shared on a local area network An independent network segment that is it has the same network address b
33. ges lightning power surges or shortages of materials or labour The customer is responsible for the security of their computer and network at all times Security fea tures may be disabled within the factory default settings NetComm recommends that you enable these features to enhance your security The warranty is automatically voided if 1 2 You or someone else use the product or attempts to use it other than as specified by NetComm The fault or defect in your product is the result of a voltage surge subjected to the product either by the way of power supply or communication line whether caused by thunderstorm activity or any other cause s The fault is the result of accidental damage or damage in transit including but not limited to liquid spill age Your product has been used for any purposes other than that for which it is sold or in any way other than in strict accordance with the user manual supplied Your product has been repaired or modified or attempted to be repaired or modified other than by a qualified person at a service centre authorised by NetComm and The serial number has been defaced or altered in any way or if the serial number plate has been removed Limitations of Warranty The Trade Practices Act 1974 and corresponding State and Territory Fair Trading Acts or legalisation of another Government the relevant acts in certain circumstances imply mandatory conditions and warranties which cannot be ex
34. iated with your network card or adapter 11 In the TCP IP Properties dialog box click the IP Address tab 12 Click the radio button labelled Obtain an IP address automatically 13 Click OK twice to confirm and save your changes You will be prompted to restart Win dows 14 Click Yes 18 V200 VoIP Telephone Adaptor Router YML795 Rev1 MEL 2 3 4 Configure the V200 via Web browser This section describes how to logon and configure the V200 via a Web browser from your PC which should be directly connected to the V200 via its LAN port A Logon to your V200 Open your Web browser IE or Netscape and type 192 168 30 1 in its address bar You will see the login window A unique default user account is assigned with user name admin and password admin Connect to 192 168 30 1 NetComm 200 User name Password admin Remember my password E After you have logged in to the V200 you will be presented with the V200 Status page Software Version Voip Account 1 Number 200 Voip Account 2 Number 201 A007 89210NCM C02 Register Status DIRECT CALL Register Status Disable Client Expire 60 Qvalue 0 8 RTP packet interval 20 Codec G729 DTMF in band Payload Type 101 MaxDigist 24 MaxRings 15 Port No 5060 UseProxy NO Internal Call Yes RTP Port 16384 Proxy Register Domain Proxy N C Port N C Domain N C WAN WAN MODE DHCP mo
35. icrosoft Internet Explorer Be ER yew Favores Tout teip O O DAD Ds frs O Z S m l Pajkos A htprjf192 168 30 1 Eje is d Todsupdste Gater Malim V2UU will reboot And it will take 20 seconds to reboot and startup WAN Setup LAN Setup V200 VoIP Telephone Adaptor Router 55 YML795 Rev1 MALUM Appendix A Cable Information This cable information is provided for your reference only Please ensure you only connect the appropriate cable into the correct socket on either this product or your computer If you are unsure about which cable to use or which socket to connect it to please refer to the hardware installation section in this manual If you are still not sure about cable connections please contact a professional computer technician or NetComm for further advice RJ 45 Network Ports RJ 45 Network Ports can connect any networking devices that use a standard LAN interface such as a Hub Switch Hub or Router Use unshielded twisted pair UTP or shield twisted pair STP cable to connect the networking device to the RJ 45 Ethernet port Depending on the type of connection 10Mbps or 100Mbps use the following Ethernet cable as prescribed 10Mbps 100Mbps Note Use EIA TIA 568 100 Category 3 4 or 5 cable Use EIA TIA 568 100 Category 5 cable To prevent loss of signal make sure that the length of any twisted pair connection does not exceed 100 metres RJ 45 Connector Pin Assignment 56 YML795 Rev1 12345678 BLL
36. ket interval 20 Codec G729 DTMF in band Payload Type 101 MaxDigist 24 MaxRings 15 PortNo 5060 UseProxy YES Internal Call Yes RTP Port 16384 Proxy Register Domain Proxy fwd pulver com Port 5060 Domain fwd pulver com WAN WAN MODE DHCP mode Current State Active WAN IP Address 192 168 1 11 Primary DNS Server 192 168 1 253 Subnet Mask 255 255 255 0 Secondry DNS Server 4 2 2 2 Default Gateway 192 168 1 253 STUN Current State Enable STUN Server stun fwdnet net Port No 3478 Note Please consult your VoIP service provider for your SIP account details whether you need to configure STUN and which codec you should use and its packet interval If unsure use the default settings When you finish your configuration click the Apply button to apply your settings Once you click the Apply button the V200 will return you to the Status page A few seconds later refresh this page using your Web browser refresh button it should display Registered Success in the Register Status field If you experience a problem please see Chapter 5 VoIP 22 V200 VoIP Telephone Adaptor Router YML795 Rev1 MEL D Save your settings and Reboot the V200 Save your setting by clicking on the Save button under the System section Saves the current configuration to the flash memory Do not turn off the power before the next page is displayed Or else the unit will be damaged Save N After yo
37. l Packets Transmitted Packets Received 3 Packet Loss 36 lo Minimum Round Trip 264 ms Time Maximum Round Trip 270 ms Time Back Field Description Packets transmitted Number of packets that were transmitted Packets received Number of packets that were received Packets loss Number of packets lost transmitted received Minimum round trip time The fastest round trip time Maximum round trip time The slowest round trip time V200 VoIP Telephone Adaptor Router 51 YML795 Rev1 Melkoni 7 4 Save A new setting will take effect immediately after the setting is submitted If the V200 is powered down however it will be lost To keep your new settings permanently you need to save them into flash memory by using the Save menu Click the Save menu item in the menu bar on the left and then click on the Save button to save your configuration settings Z Web Configuration Configuration Microsoft Internet Explorer Tm _ 5 xj File Edt View Favorites Tools Help N EAS Back gt gt 2 Al seach ijFavortes Bmedia C Eh amp Address http 192 168 0 1 60 Links 5j Gsnact yl DMZ Access Control Remote Access Saves the current configuration to the flash memory Do not turn off the power before the next page is displayed Or else the unit will be damaged Save 52 V200 VoIP Telephone Adaptor Router YML795 Rev1 MAIL 7 5 R
38. n will show you how to connect the V200 to your network A typical ADSL and cable broadband network are illustrated here ADSL Broadband In general a residential ADSL router runs PPPoE client and DHCP server for your PCs to share Internet access In this case you can just simply connect the V200 to your ADSL router as shown in Figure 2 Your PCs can connect to any LAN port in either the ADSL router or the V200 Telephone Socket NB5Plus4 ADSL Modem Router V200 VoIP Telephone Adaptor Router Analogue em RJ11 telephone cable Telephone Telephone R45 network cable Figure 2 Note V200 also has advanced routing and QoS features To use these features in conjunction with ADSL broadband service please refer to Section 4 1 WAN setup and 5 2 VoIP QoS for details V200 VoIP Telephone Adaptor Router YML795 Rev1 Melton Cable Broadband Figure 3 illustrates the V200 installation for cable broadband network RJ11 telephone cable 845 network cable Calle BNC Cable Socket Analogue Telephone V200 VoIP Telephone Adaptor Router Analogue Telephone Figure 3 V200 VoIP Telephone Adaptor Router 15 YML795 Rev1 Melton 2 3 Installation 2 3 1 Cable Connections The Phone ports of the V200 are connected to a normal analog phone using a RJ11 cable The WAN port of the V200 is connected to your ADSL Cable modem using a RJ45 cable ALAN port o
39. nnected Consult an experienced radio TV technician for help 3 The power supply that is provided with this unit is only intended for use with this product Do not use this power supply with any other product or do not use any other power supply that is not approved for use with this product by NetComm Failure to do so may cause damage to this product fire or result in personal injury V200 VoIP Telephone Adaptor Router 63 YML795 Rev1 Melton Product Warranty The warranty is granted on the following conditions 1 2 This warranty extends to the original purchaser you and is not transferable This warranty shall not apply to software programs batteries power supplies cables or other acces sories supplied in or with the product The customer complies with all of the terms of any relevant agreement with NetComm and any other reasonable requirements of NetComm including producing such evidence of purchase as NetComm may require The cost of transporting product to and from NetComm s nominated premises is your responsibility and NetComm does not have any liability or responsibility under this warranty where any cost loss injury or damage of any kind whether direct indirect consequential incidental or otherwise arises out of events beyond NetComm s reasonable control This includes but is not limited to acts of God war riot embargoes acts of civil or military authorities fire floods electricity outa
40. nter or exit Plain Old Telephone Service Point to Point Protocol A protocol RFC 1661 for transmitting packets over serial links between devices made by the same or different manufacturers V200 VoIP Telephone Adaptor Router PPPoE PPTP Protocol Proxy server PSTN QoS Remote access Remote digital loopback test Remote host RFC RIP RJ11 RJ45 Router Routing table RS 232 Server SIP Static route MEL Point to Point Protocol over Ethernet A method for establishing sessions and encapsulating PPP packets over an Ethernet specified by RFC 2516 Point to Point Tunneling Protocol An extension of Point to Point Protocol used to create virtual private networks between PCs A set of rules that govern the transmission of data between interconnected devices to maintain or improve communication Provides a list of items available on other servers to increase the availability and speed of retrieving that information Public Switched Telephone Network The standard telephone network Quality of Service The expected data loss or latency Communication from a remote location or facility through a data link This test loops the remote digital receiver output back into the transmitter input The computer receiving the network commands Request for Comments Documents published by the Internet Engineering Task Force pertaining to Internet protocols and policies Routin
41. nternet If disabled calls between Phonel and Phone2 will be routed by your VoIP providers SIP server Foontigurationy stun W Phone Book WF call Forward ial Pin 3 3 3 Account Phone Number Display Number Auth ID Auth Password Confirm Password Client Expire RTP packet interval DTMF MaxDigist Port No Internal Call Proxy Register Host Address URL Domain Domain Address 630801 NetCommV200 630801 seceee Lo 20 v in band 24 w 5060 Yes fwd pulver com fwd pulver com V200 VoIP Telephone Adaptor Router YML795 Rev1 Account2 Enable vj Phone Number Display Number Auth ID Auth Password Confirm Password QValue Codec Payload Type MaxRings UseProxy RTP Port Port No 683752 NetCommV200 683752 5060 21 MALUM Note You must configure Account 1 and Account 2 on the above page before you can use the internal call feature That means both Account 1 and Account 2 need to have a VoIP account information entered In terms of the internal call there is an alias for Account 1 and Account 2 To make internal calls just simply dial and the other phone will ring Software Version A007 S9210NCM C02 Voip Account 1 Number 630801 Register Status Registered Success Voip Account 2 Number 683752 Register Status Registered Success Client Expire 60 Qvalue 0 8 RTP pac
42. omm is a registered trademark of NetComm Limited All other trademarks are acknowledged the property of their respective owners Customer Information ACA Australian Communications Authority requires you to be aware of the following information and warnings 1 This unit shall be connected to the Telecommunication Network through a line cord which meets the requirements of the ACA TS008 Standard 2 This equipment has been tested and found to comply with the Standards for C Tick and or A Tick as set by the ACA These standards are designed to provide reasonable protection against harmful interfer ence in a residential installation This equipment generates uses and can radiate radio noise and if not installed and used in accordance with the instructions detailed within this manual may cause interference to radio communications However there is no guarantee that interference will not occur with the installation of this product in your home or office If this equipment does cause some degree of interference to radio or television reception which can be determined by turning the equipment off and on we encourage the user to try to correct the interference by one or more of the following measures Change the direction or relocate the receiving antenna Increase the separation between this equipment and the receiver Connect the equipment to an alternate power outlet on a different power circuit from that to which the receiver TV is co
43. on ID to register on fwd pulver com SIP server It will also show the use of STUN for traversing your router s NAT Firewall Stun Fulxction Stun Enable STUN IP or Domain Name stun fwdnet net STUN Type Blocked Modify Port No 1 3478 Type in your SIP account information provided by your VoIP service provider in this page The most common parameters are Phone Number also called SIP user name Authentication ID Authentication password SIP proxy host Address and SIP proxy Port and Domain address There are two VoIP accounts in this page Account 1 and Account 2 which represent Phone and Phone respectively By default the Phone 2 Account 2 is disabled So if you only have one SIP account you can simply configure the account in Phone 1 Account 1 and leave the Account 2 disabled as its default If you have two accounts you need to enable Account 2 before you configure it If you have a VoIP account you need to choose YES in the UseProxy option the default setting of this option is in Non Proxy mode Then you can input SIP Proxy Register server information and let the V200 register with the specified SIP server The Internal Call option allows you to specify how the V200 handles calls between Phone 1 and Phone 2 when they have separate VoIP accounts By default this feature is enabled and allows you to route the calls locally between Phonel and Phone 2 i e In this case there is no traffic going through to the I
44. or Router 57 YML795 Rev1 Melton Appendix B Glossary 100BaseT 10BaseT Arp Address ASCII Bandwidth Baud Bit Boot Bps Bridge Broadband Broadcast Byte CHAP CPE DHCP server DHCP DNS Download 58 YML795 Rev1 A 100 Mbps Ethernet standard that uses twisted pair wiring A 10 Mbps Ethernet standard that uses twisted pair wiring Address Resolution Protocol The symbol usually numeric identifying an interface attached to a network American Standard Code for Information Interchange The range of frequencies of a transmission channel The wider the range the higher the data rate that can be sent Hence bandwidth is also taken to mean the data rate One baud is one symbol state transition or level transition per second A binary digit with the value of 0 or 1 Start a device Bits per second The speed at which bits are transmitted across a data connection A device that links local or remote area networks together forwarding packets based on a MAC address compare with gateway Communication channels operating at transmission rates in excess of 64 Kbps The simultaneous transmission to two or more communication devices Eight bits arranged in sequence Challenge Handshake Authentication Protocol A PPP protocol to ensure authentication of the connection between two devices Customer Premises Equipment Equipment used by the end user A serve
45. ough the Internet Click the Remote Access menu item in the menu bar on the left to enable remote access to your V200 eb Configuration configuration Microsoft Internet Ep OO zigixi Fie Edt View Favorites Tools Help ES Back gt gt O A A Reach Favorites Meda C B 5 Address http 192 168 30 1 60 Links Gsractt ts Remote Access NAT Port Forwarding DMZ Access Control Remote Access Enable gt Apply Remote Access Status Traffic Statistics Remote Access feature can put your V200 at risk because an intruder can access it in the same way This menu gives you the option to Enable or Disable this feature Simply make your selection then click the Apply button to submit the setting The default is Disable Note It is good practice to enable this feature only when necessary 46 V200 VoIP Telephone Adaptor Router YML795 Rev1 Melton Chapter 7 V200 System Information This Chapter describes the System section where information on the whole system is displayed or is used to implement certain configurations 71 Status The Status window displays the basic information of the system Itis also the first window displayed when you login to the web configuration utility You also can bring up this window by clicking on Status menu item on the left in the menu bar Software Version A007 89210NCM C02 Voip Account 1 Number 630801 Voip Account 2 Number 683752 Register
46. r PC and the V200 you can skip this section and proceed directly to 3 2 Web Login 3 2 Web Login Open a Web browser and type 192 168 30 1 in its address bar You will see the login window Connect to 122 68 30 1 A NetComm 200 User name E admin v Password fee sd Remember my password a Enter your user name and password then click OK The following V200 Status window is an example of what will be displayed The contents of this page are explained in the chapters 4 and 5 Software Version A007 S9210NCM C02 Voip Account 1 Number 630801 Register Status Registered Success Voip Account 2 Number 683752 Register Status Registered Success Client Expire 60 Qvalue 0 8 RTP packet interval 20 Codec G729 DTMF in band Payload Type 101 MaxDigist 24 MaxRings 15 Port No 5060 UseProxy YES Internal Call Yes RTP Port 16384 Proxy Register Domain Proxy fwd pulver com Port 5060 Domain fwd pulver com WAN WAN MODE DHCP mode Current State Active WAN IP Address 192 168 1 11 Primary ONS Server 192 168 1253 Subnet Mask 255 255 255 0 Secondry DNS Server 4 2 2 2 Default Gateway 192 168 1 253 STUN Current State Enable STUN Server stun fwdnet net Port No 3478 24 V200 VolP Telephone Adaptor Router YML795 Rev1 Melton Chapter 4 WAN and LAN Set up The Basic Menu tab is located on the left hand side of the Web interface With these screens you c
47. r that dynamically allocates network addresses and delivers configuration parameters to hosts Dynamic Host Configuration Protocol A TCP IP protocol that enables a network connected to the Internet to automatically assign a temporary IP address to a host when the host connects to the network Domain Name Server A server that retains the addresses and routing information for TCP IP PAT users To receive a file over a network compare with upload V200 VoIP Telephone Adaptor Router DSP DTE Dynamic detection Ethernet address Ethernet ETSI Firmware Flash memory YML795 Rev1 MEL Digital Signal Processor The microprocessor that handles line signaling in a modem Data Terminal Equipment Equipment that transmits or receives data in the form of digital signals A process of a automatic detection of a new device added or removed from the PC Another name for MAC address A standard protocol IEEE 802 3 for a 10 Mb s baseband local area network PAT bus that supports high speed communication among systems It operates at the Physical Layer of the OSI Model European Telecommunications Standards Institute Software that has been temporarily or permanently loaded into ROM A type of RAM that retains its information even after powering down FTP File Transfer Protocol A TCP IP standard protocol for transferring files Gateway A communications device that connects two different networks
48. s 0011 XXY YY YYY So she can keep her dialling habit as she is dialling overseas in UK V200 VoIP Telephone Adaptor Router 39 YML795 Rev1 MAIL Enter the information and click the Add button You will be returned to the Dial Plan list window with the added plan now displayed You also can modify or delete any specific method from the Dial Plan by selecting the corresponding Select option and clicking on the Modify or Delete button 40 V200 VoIP Telephone Adaptor Router YML795 Rev1 Melkoni 5 2 VolP QoS VoIP QoS is a function that allows users to keep enough bandwidth for VoIP calls during heavy Internet usage periods hence it can maintain high quality VoIP calls Conditions of QoS There are two conditions to use the V200 QoS feature properly Firstly your broadband Internet connection should have a fixed upstream bandwidth Cable broadband Internet services share a fixed bandwidth and therefore do not have a fixed upstream bandwidth for their Internet access In contrast ADSL users normally have a fixed upstream bandwidth which should be stated in their ADSL service plan contract Secondly you will need to let your V200 to handle the Internet traffic for your LAN network We recommend you install your V200 based on the following network diagram which will let the V200 QoS work properly If you have already had an ADSL router working you will need to reconfigure your ADSL router into bridge mode in order to use the QoS feature
49. si xr aa su tripod cssc hi ER RSRU DURER IE 16 2 3 4 Configure the V200 via Web DrowSel cccccscecsseeeeeeseeseeeaneeeeeeeeeeeeeaeeeseeeseees 19 Chapter 3 How to Log in using a Web Browser eeeee eene nennen nena nnn 24 3 1 V200 TP AddEeSS zccucsssis Ens PxEx ern cese Rex suis AER RARU e UN EMILE ERE 24 3 2 sigo e ET 24 Chapter 4 WAN and LAN Setups sine iiit icn nave totu ien nee letus a c uice RaT divans 25 4 1 WAN Setup cites guisa Aa ne su vnn hr ckaR E Ke aa xrtex Si na fna adi ajuste DE Pu 25 4 1 1 Static IP addres Smia nn bdersesr sa oree ie mers nad tuos REL iR DEP URNA 27 4 1 2 IDHCP MOGG 5iuitau acteur pertes conii nii ax eru edu Eaa AR abbas RR niae RE DdS 28 AAS IRPPOE m M 29 4 2 LAN TP AGOPOSS P 30 Chapter 5 VOIP Setup caiinnctiesvaiedvencsiatodencaan rna beer paie ce E AA E ia E 31 5 1 SIPS eI 31 5 1 1 COMMON ALON areca dinates quere lirics tence cla cana aes SE E E E EN 31 51 2 STUN EET 35 5 1 3 Phone BOOK sesccccccansisninasd sasvtndeasbacaccecacanstenadscadsntieed cebeaaanceseanetbindaadhaentedeaes 36 Dele Call Forward sesoun onan EAE A EE a AEN E 37 5 4 5 Dial Plan nc diecsccccccssassiecncnseniee tet qaiasnecsanssanidaadancitiveadbeieansactees peindiaamemaneedaaios 39 5 2 v Neo fj e 41 Chapter 6 Additional Routing Feat res incdus ortae etienne pado citu niches
50. ss URL Port No Domain Domain Address Software Version Voip Account 1 Number Voip Account 2 Number 683752 Client Expire RTP packet interval DTMF ii MaxDigist Port No Internal Call A007 89210NCM C02 630801 Proxy Register Domain Proxy Domain WAN WAN MODE WAN IP Address Subnet Mask Default Gateway STUN Current State STUN Server fwd pulver corn fwd pulver com DHCP mode 192 168 1 11 255 255 255 0 192 168 1 253 Enable stun fwdnet net V200 VoIP Telephone Adaptor Router YML795 Rev1 IP address of the SIP proxy server Port number of the SIP Proxy server at which it listens to your VoIP signalling messages Default 5060 Domain name of the SIP Registrar server Register Status Registered Success Register Status Registered Success Qvalue 0 8 Codec G729 Payload Type 101 MaxRings 15 UseProxy YES 16384 RTP Port Port 5060 Current State Primary DNS Server Secondry DNS Server Port No Active 192 168 1 253 4 2 2 2 MALUM Enter or select the required information and then click on the Apply button to submit the settings The system status window will be opened The SIP registration status is displayed in the top right hand corner It will take a while to complete the registration process Use the Refresh button on your web browser to check the registration status Field Description Register Stat
51. ted by the V200 6 1 NAT Port Forwarding Port forwarding is the action of forwarding network ports on the WAN interface to PCs or servers in LAN network Virtual servers use this technique to allow external users in most cases via the Internet to reach services provided by internal servers such as FTP HTTP Telnet etc The V200 has the capability to perform port forwarding Click the NAT Port Forward menu item in the menu bar on the left to display the current port forward setting i Web Configuration Configuration Microsoft Internet Explorer OOOO zox le Edt View Favorites Tools Help Back gt A A search Ggravorites media A B B Address http 192 168 30 1 7 So Links il sagt S 2 WAN Setup Port Forwarding LAN Setup Port Forwarding Configuration Public Port From 21 SIP VoIP QOS Public Port To 22 M Protocol tcp Local Address FEFIEEEREIBEIS Local Port From 21 NAT Port Forwarding DMZ Access Control Remote Access Local Port To 22 Cancel Field Description Public Port From Public Port To Type in the public port for remote user accessing The category is 1 65535 Protocol TCP or UDP Local Address Type in the local IP address Local Port From Local Port To Type in the Local Port You can add a new entry using the Add button or delete an entry by selecting the corresponding Select option and clicking on the Delete button V200 VoIP Telephone Adaptor Router 43 YML7
52. the products will operate in accordance with the specifications outlined in the User Guide However some products have an extended warranty option please refer to your packaging To be eligible for the extended warranty you must supply the requested warranty information to NetComm within 30 days of the original purchase by registering on line via the NetComm web site at www netcomm com au Contact Information If you have any technical difficulties with your product please do not hesitate to contact NetComm s Customer Support Department Email support netcomm com au Fax 612 9424 2010 Web www netcomm com au Copyright Information This manual is copyright Apart from any fair dealing for the purposes of private study research criticism or review as permitted under the Copyright Act no part may be reproduced stored in a retrieval system or transmitted in any form by any means be it electronic mechanical recording or otherwise without the prior written permission of NetComm Limited NetComm Limited accepts no liability or responsibility for consequences arising from the use of this product Please note that the images used in this document may vary slightly from those of the actual product Specifications are accurate at the time of the preparation of this document but are subject to change without notice NetComm Limited reserves the right to change the specifications and operating details of this product without notice NetC
53. u save the settings click the Reboot button to reboot the V200 You have completed the basic configuration of your V200 200 will reb ot nd it will take 20 seconds to reboot and startup Reboot You have now completed the basic installation and configuration of your new NetComm V200 At this point you will be able to make VoIP calls to and from your V200 connection You may consider contacting your VoIP service provider s customer support line to test your VoIP service and enable any available supplementary call features V200 VoIP Telephone Adaptor Router 23 YML795 Rev1 Melton Chapter 3 How to Log in using a Web Browser This chapter describes how to manage the V200 via a Web browser from a PC directly connected to the V200 You can use a web browser such as Microsoft Internet Explorer Netscape Navigator or Mozilla Firefox A default user account is assigned with user name admin and password admin You can change the default password later after logging on to the device 3 1 V200lP Address To log on to the V200 using a web browser your PC and the V200 should both be on the same network segment The default IP address for the V200 is 192 168 30 1 If your PC is not on the same network segment you can modify its IP address or change its IP address assignment to DHCP mode so that the V200 can assign a valid LAN IP address to your PC Note If you have already completed the Quick Start section and successfully connected you
54. us There are three instances as explained in the following DIRECT CALL will be displayed all the time if you choose non UseProxy mode Not Registered will be displayed if you configure the V200 in UseProxy mode but fail to register Registered Success will be displayed if you choose UseProxy mode and registered successfully VoIP Phone number Client Proxy Register Domain WAN and STUN display their related information 34 V200 VoIP Telephone Adaptor Router YML795 Rev1 MIL 5 1 2 STUN STUN stands for Simple Traversal of UDP over NAT It is a protocol which enables the V200 to detect the presence and type of NAT behind which the phone is placed STUN will allow SIP signalling and bi direction to successfully traverse a NAT without requiring any configuration changes on the NAT Stun Fution Stun Enable z STUN IP or Domain Name stun fwdnet net Port No 3478 STUN Type Blocked Modify Select Enable or Disabled enter all the information if Enable is selected and then click on the Modify button to apply the new settings Field Description STUN IP or Domain Name The IP address or domain name of the STUN server which could be provided by your service provider or a free STUN server on the Internet STUN type This column is Read Only The STUN mechanism will identify your NAT type and display it on the screen Port No Port number of the STUN server where the server listens to your STUN client requests
55. ut UP laszess 3118 i15 o 0 1961949 2361 0 o 0 GENI o so1278 2937 o Interface Name Name of the interface Admin Status Indicates whether the interface is Up or Down Octets In Number of Octets bytes received Unicast PktsIn Number of unicast packets received Broadcast PktsIn Number of broadcast packets received Discards In Number of packets received that were discarded Errors In Number of inward errors Octets Out Number of Octets bytes transmitted Unicast PktsOut Number of unicast packets transmitted Broadcast PktsOut Number of broadcast packets transmitted Discards Out Number of packets transmitted that were discarded Errors Out Number of outward errors 48 V200 VoIP Telephone Adaptor Router YML795 Rev1 MAI mm 7 2 2 TCP IP The TCP IP page displays the IP statistics UDP statistics TCP statistics and ICMP statistics Interfaces TCP IP DHCP Lease TCP IP Statistics IP Statistics In receives 22337 In Errors f212 In Unknown Protos 0 Forwarded Datagrams 0 Out Requests 9165 Out Discards 0 Out No Routes le12 UDP Statistics Datagrams In i03 Datagrams Out 7621 Errors In 0 TCP Statistics Active Opens D Passive Opens 54 Attempt Fails lo Current Establishments 1 Segments In 1386 Segments Out 1513 Segments retransmitted 15 Errors In lo ICMP Statistics IN Messages 18
56. ut its subnet address is different A data switch connects computing devices to host computers enabling multiple devices to share a limited number of ports An electrical switch is a device for making breaking or changing the connections in an electrical circuit Transmission control protocol Internet protocol a set of protocols that govern peer to peer connectivity functions for local and wide area networks Transmission Control Protocol The TCP IP virtual terminal protocol that allows a user at one site to access a remote system at another site The number of bits characters or blocks that are able to pass through a data communication system User Datagram Protocol A connectionless protocol that converts data messages generated by an application into packets to be sent over IP To receive a file transmitted over a network Uniform Resource Locator An Internet standard addressing protocol for describing the location and access method of a resource on the Internet Virtual Private Network A network implemented over a public network that is made private by use of encryption Wide area network A communications network that connects geographically separated areas Compare with LAN V200 VoIP Telephone Adaptor Router MEL Appendix C Registration and Warranty Information All NetComm Limited NetComm products have a standard 12 month warranty from date of purchase against defects in manufacturing and that
57. utomatically Also click the radio button labelled Obtain DNS server address automatically 6 Click OK twice to confirm and save your changes and then close the Control Panel Windows Me PCs 1 In the Windows task bar click the Start button point to Settings and then click Con trol Panel Click on View All Control Panel Options 3 Double click the Network icon 4 The Network Properties dialog box displays with a list of currently installed network components If the list includes Internet Protocol TCP IP then the protocol has already been enabled Skip to step 10 N 5 If Internet Protocol TCP IP does not display as an installed component click Add 6 Inthe Select Network Component Type dialog box select Protocol and then click Add 7 Select Microsoft in the Manufacturers box 8 Select Internet Protocol TCP IP in the Network Protocols list and then click OK You may be prompted to install files from your Windows ME installation CD or other media Follow the instructions to install the files If prompted click OK to restart your computer with the new settings Next configure the PC to accept IP information assigned by the modem 9 Follow steps 1 4 above 10 In the Network Properties dialog box select TCP IP and then click Properties If you have multiple TCP IP listings select the listing associated with your network card or adapter 11 In the TCP IP Settings dialog box click the radio b
58. utton labelled Obtain an IP ad dress automatically 12 Click OK twice to confirm and save your changes and then close the Control Panel V200 VoIP Telephone Adaptor Router 17 YML795 Rev1 Melton Windows 95 98 PCs First check for the IP protocol and if necessary install it l 9 In the Windows task bar click the Start button point to Settings and then click Con trol Panel Double click the Network icon The Network dialog box displays with a list of currently installed network components If the list includes TCP IP and then the protocol has already been enabled Skip to step 9 If TCP IP does not display as an installed component click Add The Select Network Component Type dialog box displays Select Protocol and then click Add The Select Network Protocol dialog box dis plays Click on Microsoft in the Manufacturers list box and then click TCP IP in the Net work Protocols list box Click OK to return to the Network dialog box and then click OK again You may be prompted to install files from your Windows 95 98 installation CD Follow the instruc tions to install the files Click OK to restart the PC and complete the TCP IP installation Next configure the PCs to accept IP information assigned by the modem Follow steps 1 3 above 10 Select the network component labelled TCP IP and then click Properties If you have multiple TCP IP listings select the listing assoc
59. v1 MEL 4 1 3 PPPoE When using PPPoE the V200 will assign you an IP address via PPPoE protocol from your ISP When WAN port is set in PPPoE mode the V200 will do routing for your network and you are able to enable its QoS feature Please see Section 5 2 for details about cable connection of the V200 and your ADSL modem router and its WAN mode Select the PPPoE mode option and click on the Next button to display the following window WAN SETUP PPPoE Configuration User name netcommacsp your dsl net Password Confirm Password Apply Cancel Field Description User name PPPoE account username This is not your VoIP number This username is issued by your ISP Password PPPoE account password This is not your VoIP password This password is issued by your ISP Confirm Password Same as Password Enter your Username Password and Confirm password then click the Apply button to summit the settings V200 VoIP Telephone Adaptor Router 29 YML795 Rev1 MAIL 4 2 LAN IP Address Click LAN Setup from the menu bar to bring up the LAN Setup window LAN Setup LAN IP Address 192 168 30 1 NetMask 255 255 255 0 DHCP Server Configuration Status Enable DHCP Server Enable Starting IP Address 192 168 30 2 End IP Address 152 168 30 100 Lease Time in Days I o Apply Cancel Field Description LAN IP Address The unique IP address of the V200 on the LAN network
60. warded Choose NO if you do not want calls to be forwarded User Name SIP user name VoIP number to which calls will be forwarded to e g 09100308 Host Addr or Domain Name If you use the V200 in SIP proxy mode this is the Domain name in which your V200 currently registers If you use V200 in Non Proxy mode this is the IP address of the forward to VoIP ATA or IP phone Port No The port number at which the remote ATA IP phone or SIP server listen SIP request Default 5060 Fwd Uncond If you choose Yes incoming calls will be forwarded to the specified number without ringing on your VoIP phone If you choose No your VoIP phone will ring the specific number of times before being forwarded to the number above Fwd Rings The specified number of rings before Unconditional call forwarding happens V200 VoIP Telephone Adaptor Router 37 YML795 Rev1 Melton Enter the information and click on the Modify button You will be returned to the Call Forward List window with the modified details now displayed You also can delete any entry from the call forward list by selecting the corresponding Select option and clicking on the Delete button In the V200 s default state there are no entries for this window so the Add button is displayed instead of the Modify button Use the Add button to add the list 38 V200 VoIP Telephone Adaptor Router YML795 Rev1 MEL 5 1 5 Dial Plan Dial Plan can make your dialling easier If the dialle

NetComm V200 User Guide

Contents

Download Pdf Manuals

Related Search

Related Contents