OnyxPro 132 User Manual
Contents
1. OmniSistem www omnisistem com Fax 253 395 9494 Tel 253 395 9500 6403 South 208 Street Kent WA 98032 KEEP THIS MANUAL FOR FUTURE NEEDS C 1 of 26 Every person involved with the installation operation and maintenance of this device needs to be qualified follow the instructions of this manual consider this manual to be part of the total product keep this manual for the entire service life of the product Pass this manual on to every further owner or user of the product Download the latest version of the user manual from the OmniSistem website CAUTION Keep this device away from rain and moisture Disconnect power before opening the housing For your own safety please read this user manual carefully before you initially start the product INTRODUCTION Thank you for choosing an OmniSistem product OmniSistem is a wholesaler of a large variety of lighting sound truss and effects Since 1986 we have been providing quality and affordable lighting products to North America We are confident that our excellent products will meet your expectations Included in this box you will find OnyxPro 132 User Manual Omega Holder with Quick Lock Fastener Power Supply Cable Safety Cable oe eS SAFETY INSTRUCTIONS This device left our facility after a thorough QC check In order to maintain excellent condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety i2. During the installation do not touch the glass bulbs bare handed Please follow the lamp manufacturer s notes Do not install lamps with a higher wattage Lamps with a higher wattage generate temperatures the device was not designed for Damages caused by non observance are not subject to warranty Procedure Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 Unscrew the eight housing screws standard Philips screws of the projector head cover and remove the projector head cover Unscrew the fixation screws A and B of the lamp system and carefully remove the cover from the housing Unscrew the fixation screw of the lamp holder Push the plate to the right side If replacing the lamp remove the old lamp from the lamp holder First carefully detach the two connection wires from the lamp base Remove the lamp from the lamp holder Carefully insert the new lamp into the lamp holder Carefully attach the two connection wires onto the lamp base Please make sure that the new lamp is in the same position as the old lamp before closing the device Replace the lamp system in the housing and tighten the fixation screws Replace the projector head cover and tighten the screws Attention Please note the Osram Sirius HRI 132W lamp is not a hot restrike type You must wait approximately 10 minutes before you can attempt to strike the lamp once it has been turned off 7 of 26 CAUTION Do not operate this device wit
3. On Off Password XXX Private Reload On Off All Reload On Off Master Standalone Play DMX Receive Slave Receive Sequence Music Music Standalone Select Chase Chase Part 1 Chase 1 8 Chase 1 Chase Part 2 Chase 1 8 Chase 2 Chase Part 3 Program Slave Receive 1 2 3 17 of 26 Reset All Reset Pan amp Tilt Reset Shutter Reset Colors Reset Gobos Reset Others Pan Reverse Tilt Reverse Choose Pan Degree Encoder Wheel On Off Choose Pan Tilt Mode Sensitivity of Mic Mode When No Signal Temperature F or C Fan Auto or High Sleep Time Backlight Time Reverse Display 180 Brightness Setting Show Branding Key Lock On Off Language Select Standard DMX Mode Extended DMX Mode 8 bit Mode 16 bit Mode User mode Edit User Mode Password 050 Edit Channel Value Name Password 050 Set PID of RDM Basic Reload Program Reload Password 050 Private Reload All Reload DMX Receive Choose Slave Position Run Sequence Music Mode Select and Run Auto Program Edit Chase 2 Chase 1 Chase Test Test Zi Step 01 SCXXX Beginning Scene Chase 8 Step 64 SCXXX Ending Scene Edit Scenes 2 Edit Scene 001 Pan Tilt Input Manual Scene Edit Scene Fade Time Fading Time 250 Scene Scene Time Time Input Scene from DMX Input Controller Connect DMX Address Setting With this function you can adjust the desired DMX address via the Control Board Select DMX Address by pressing Up or D
4. XLR termination plug with 120 Ohm in the last lighting in the link in order to ensure proper transmission on the DMX data link DMX Protocol 1 ofp ffm two os Cle fe rte i oa a fs e froenn reese oas Movement Normal 0 15 Function Movement w Blackout 16 31 No Function 32 255 Shutter Function Normal Shutter Functions Pulse Effect Forward Pulse Effect Reverse Random Strobe No Function 5 Shutter Normal Shutter Functions Close Strobe Rate Slow to Fast Open Pulse Effect Forward Close Strobe Rate Slow to Fast Open Pulse Effect Reverse Close Strobe Rate Slow to Fast Open Random Strobe Close Strobe Rate Slow to Fast Open 13 of 26 32 223 224 25 5 Shutter Shutter Closed No Function Shutter Open Strobe Effect Slow to Fast No Function Shutter Open Pulse Effect in Sequences No Function Shutter Open Random Strobe Effect Slow to Fast No Function Shutter Open p p pe foree Color Function Indexed Indexed w Blackout Forward Spin Reverse Spin Continuous Color Bounce No Function Indexed amp Indexed w Blackout amp Color Bounce Position 1 Open Position 2 Position 15 Forward Spin Stop to Fast Reverse Spin Stop to Fast Continuous Positioning 0 360 Indexed Position 1 Open Position 2 Position 15 Indexed w Blackout Position 1 Open Position 2 Position 15 Indexed w Bounce Position 1 Open Position 2 Position 15 Forward
5. program Please refer to the instructions under Control Board DMX Controlled operation You can control the projectors individually via your DMX controller Every DMX channel has a different occupation with different features The individual channels and their features are listed under DMX protocol Addressing The Control Board allows you to assign the DMX starting address which is defined as the first channel from which the fixture will respond to the controller If you set for example the address to channel 20 a fixture in 18 channel mode would use channels 20 to 38 for control Please be sure that you don t have any overlapping channels in order to control each fixture correctly and independently from any other fixture on the DMX chain If several fixtures are addressed similarly they will work in sync Press the Up Down buttons for setting the desired starting address Now you can start operating the fixture via your lighting controller 12 of 26 Note After switching on the device will automatically detect whether DMX 512 data is received or not If there is no data received at the DMX input the display will flash This situation can occur if e the XLR plug cable with DMX signal from controller is not connected with the input of the device the controller is switched off or defective if the cable or connector is defective or the signal wires are swapped in the input connector Note Its necessary to insert the
6. to e g prevent menu tampering If this function is activated the keys will be automatically locked as soon as you exit the menu In order to deactivate or temporarily deactivate the key lock function press UP DOWN LEFT RIGHT ENTER to regain access to the menu commands Users User mode With this function you can create user defined channel orders Edit User With this function you can adjust the preset user defined channel order Calibration With this function you can calibrate and adjust the effect wheels to their correct positions The password for this function is 050 Fixture ID RDM With this function you can call up various submenus via RDM This device is RDM ready RDM stands for Remote Device Management and makes remote control of devices connected to the DMX bus possible ANSI E1 20 2006 by ESTA specifies the RDM standard as an extension of the DMX 512 protocol Manual settings like adjusting the DMX starting address are no longer needed This is especially useful when the device is installed in a remote area RDM is integrated in DMX without influencing the connections The RDM data is transmitted via the standard XLR poles 1 and 2 new DMX cables are not necessary RDM ready and conventional DMX devices can be operated in one DMX line The RDM protocol sends its own packages in the DMX 512 data feed and does not influence conventional devices If DMX splitters are used and RDM control is to be used these sp
7. M12 screw and nut onto the Omega holder Insert the quick lock fasteners of the Omega holder into the respective holes on the bottom of the device Tighten the quick lock fasteners fully clockwise 10 of 26 DMX 512 connection connection between fixtures Projector 1 Projector 2 Projector 3 Starting address 1 Starting address 20 Starting address 39 ND SQ gt 120 Ohms SS NRA MX 512 Controller o The wires must not come in contact with each other otherwise the fixtures may fail to operate Please note the starting address depends upon which controller is being used Only use a DMX cable and 3 pin XLR plugs and connectors in order to connect the controller with the fixture or one fixture with another Occupation of the XLR connection XLR mounting socket XLR mounting plug 1 Ground 1 G Laine Grounc 2 Signal 2 Signal 3 Signal 3 Signal If you are using controllers during your show you can connect the DMX output of the controller directly with the DMX input of the first fixture in the DMX chain If you wish to connect DMX controllers with other XLR outputs you need to use adapter cables Building a serial DMX chain Connect the DMX output of the first fixture in the DMX chain with the DMX input of the next fixture Always connect one output with the input of the next fixture until all fixtures are connected Caution At the last fixture the DMX cable n
8. Wheel Spin Stop to Fast Reverse Wheel Spin Stop to Fast Fa 14 of 26 Indexed w Blackout Forward Spin Reverse Spin Continuous Shake No Function Indexed amp Indexed w Blackout amp Shake Position 1 Open Position 2 Position 18 Forward Wheel Spin Stop to Fast Reverse Wheel Spin Stop to Fastest Continuous Positioning 0 360 Indexed Position 1 Open Position 2 Position 18 Indexed w Blackout Position 1 Open Position 2 Position 18 Indexed w Shake Position 2 Position 3 Position 18 Forward Wheel Spin Stop to Fast Reverse Wheel Spin Stop to Fast Prism amp Prism Prism Open Rotation Prism Rotation Stop to Fast Prism Rotation Reversed Stop to Fast efe a im ramon 13 Control Normal Reset All Reset Pan amp Tilt Reset Color Reset Gobo Reset Shutter Reset Other Display Off Display On Lamp Off Lamp On Hibernate No Function 15 of 26 Control Board The Control Board offers several features You can simply set the starting address run the pre programmed program or perform a reset Main Menu The main menu is accessed by pressing Enter until the display is lit Browse through the menu by pressing the arrow buttons up down left right Press Enter in order to select the desired menu You can change the selection by pressing the arrow buttons Press Enter in order to confirm selection then exit back to the main menu to save changes The function
9. al scenes under Edit Scenes With this function you can run the individual scenes either automatically i e with the adjusted step time The selection Alone means stand alone mode and Master that the device is defined as master Music With this function you can run the internal program in sound controlled mode The selection Alone means stand alone mode and Master that the device is defined as master Select Chase for Auto Program With this function you can select the program for the Program Run Edit Chase With this function you can edit the internal programs Edit scenes With this function you can edit the scenes of the internal programs Rec Controller The device features an integrated DMX recorder that allows you to transmit the programmed scenes from your DMX controller to the device Adjust the desired scene numbers by pressing Up or Down When you call up the scenes at your controller they will automatically be transmitted to the device Excursion A master unit can send up to three different data groups to the slave units i e a master unit can start three different slave units which run three different programs The master unit sends the three program parts in a continuous loop The slave unit receives data from the master unit according to the group which the slave unit was assigned to If e g a slave unit is set to Slave 1 in the menu Set to Slave the Master unit sends Auto Program Part 1 t
10. ed objects The minimum distance between light output and the illuminated surface must be more than this value The device must only be installed on a non flammable surface In order to safeguard sufficient ventilation leave 50cm of free space around the device The housing must never touch surrounding surfaces or objects Make sure that the area below the installation place is clear when rigging derigging or servicing the fixture For overhead use mounting height gt 100 cm always fix the fixture with an appropriate safety cable Fix the safety cable at the correct fixation points only The safety cable must never be fixed at the transport handles Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened The maximum ambient temperature 7 45 C must never be exceeded Operate the device only after having become familiarized with its functions Do not permit operation by persons not qualified for operating the device Most damages are the result of unprofessional operation Please use the original packaging if the device is to be transported Please consider that unauthorized modifications on the device are forbidden due to safety reasons and will void your warranty Never remove the serial barcode from the device as this would void the warranty If this device will be operated in any way different to the one described in this manual the product may suffer damages and the g
11. eeds to be terminated Plug the terminator with a 1200 resistor between Signal and Signal in the DMX output of the last fixture 11 of 26 Connection with the Mains Connect the device to the power source with the enclosed power supply cable The configuration of the connection cables is as follows Cable Pin International Ground needs to be connected If the device will be directly connected with the local power supply network a disconnection switch with a minimum opening of 3mm at every pole has to be included in the permanent electrical installation The device must only be connected with an electric installation carried out in compliance with the IEC standards The electric installation must be equipped with a Residual Current Device RCD with a maximum fault current of 30mA Device must not be connected to dimming packs The device is equipped with a lockable power input connector Plug in the power cord and turn it to the right until it locks Plug the power cord into a grounded electrical outlet that matches the rated voltage of the machine OPERATION With the power switch you can switch the device on and off After being connected to the power supply the fixture starts running During the reset the motors are trimmed and the device is ready for use Stand Alone operation In the Stand Alone mode the device can be used without controller Disconnect the fixture from the controller and call the internal
12. ent modes if there is no DMX signal 1 Select Close Hold Auto or Music by pressing Up or Down 2 Press Up or Down to select between Close Hold Auto or Music 3 Press the Enter button to confirm Select Temperature Designation With this function you can select the temperature designation 1 Select Temperature C F by pressing Up or Down 2 Press Up or Down to select the desired degree between Celsius and Fahrenheit 3 Press the Enter button to confirm Hibernation Power Standby Mode With this function you can put the device in the power standby mode This function will be automatically activated after a predefined period of time of no DMX activity In standby mode the lamp LEDs and all motors will power down if no DMX signal is sent to the fixture for a period of e g 15 minutes can be user defined The fixture will automatically reset and return to normal operation once a DMX signal is sent Backlight With this function you can shut off the display after 2 to 60 minutes Flip Display With this function you can flip the display by 180 for a better view when the fixture is installed upside down 19 of 26 Shortcut Press up and down for three seconds to flip the display directly Brand Show With this function you can show or hide the brand name on the display during menu operation but still show it after reset Key Lock With this function you can lock the keys of the Control Board
13. ery four years in the course of an acceptance test The operator needs to make sure that safety related and machine technical installations are approved by a skilled person once a year Procedure The projector should be installed outside areas where persons may walk by or be seated IMPORTANT OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE including but not limited to calculating working load limits installation material being used and periodic safety inspection of all installation material and the projector If you lack these qualifications do not attempt the installation yourself but instead use a professional structural rigger Improper installation can result in bodily injury and or damage to property 8 of 26 The projector needs to be installed out of reach of people If the projector shall be lowered from the ceiling or high joists professional trussing systems need to be used The projector must never be fixed swinging freely in the room Caution Projectors may cause severe injuries when crashing down If you have doubts concerning the safety of a possible installation do NOT install the projector Before rigging make sure that the installation area can hold a minimum point load of 10 times the projector s weight DANGER OF FIRE When installing the device make sure there is no flammable material within 0 5 meters of the unit CAUTION Use an appropriate clamp to rig the fixture on the truss Follow instructions
14. h the cover housing open Inserting Exchanging Gobos DANGER Only install gobos with the device switched off and disconnected from power If you wish to use other gobos or if gobos are to be exchanged please follow the instructions below CAUTION Never unscrew the screws of the rotating gobo as the ball bearings will be opened Rigging DANGER TO LIFE Please consider the EN 60598 2 17 and the respective national norms during installation The Installation must only be carried out by an authorized dealer The installation of the projector has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation The installation must always be secured with a secondary safety attachment e g an appropriate catch net This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails When rigging derigging or servicing the fixture staying in the area below the installation place on bridges under high working places and other endangered areas is forbidden The operator needs to make sure that safety related and machine technical installations are approved by an expert before taking into operation for the first time and after changes before taking into operation another time The operator needs to make sure that safety related and machine technical installations are approved by an expert after ev
15. h them with wet hands as this could lead to mortal electrical shock Never modify bend strain mechanically put pressure on pull or heat up the power cord Never operate next to sources of heat or cold Disregarding this can lead to power cord damages fire or mortal electrical shock The cable insert or the female part in the device must never be strained There must always be sufficient cable to the device Otherwise the cable may be damaged which may lead to mortal damage Make sure that the power cord is never crimped or damaged by sharp edges Check the device and the power cord from time to time If extension cords are used make sure that the core diameter is sufficient for the required power consumption of the device All warnings concerning the power cords are also valid for possible extension cords Always disconnect from the power source when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord Otherwise the cable or plug can be damaged leading to mortal electrical shock If the power plug or the power switch is not accessible the device must be disconnected via the mains If the power plug or the device is dusty the device must be taken out of operation disconnected and then be cleaned with a dry cloth Dust can reduce the insulation which may lead to electrical shock More severe dirt in and at the device should only be removed by a specia
16. hase by pressing Up or Down Press the Enter button to confirm Press Up or Down to select the desired program With this function you can edit specific scenes into a specific program Press the Enter button to confirm Automatic Scene Recording 1 Select Edit Chase by pressing Up or Down 2 Press the Enter button to confirm 3 Select Edit scenes by pressing Up or Down 4 Press the Enter button to confirm 1 Press Up or Down to select the desired scene numbers You can program a maximum number of 250 scenes 2 Press the Enter button to confirm 3 Press Up or Down to select the desired value 4 Press the Enter button to confirm Example Program 2 includes scenes 10 11 12 13 Program 4 includes scenes 8 9 10 Program 6 includes scenes 12 13 14 15 16 Chase Part 1 is Program 2 Chase Part 2 is Program 3 Chase Part 3 is Program 6 The three slave groups run the Auto Program in certain time segments as shown in the following picture Part 1 seme some soma somes fH Part 2 23 of 26 Error Messages When you turn on the fixture it will perform a reset first The display may show an error message while there are problems with one or more channels The error message stands for the channels equipped with a testing sensor For example when the display shows Err channel PAN it means there is some error in the horizontal movement PAN control channel 1 If there are some erro
17. list There must never enter any liquid into power outlets extension cords or any holes in the housing of the device If you believe even a minimal amount of liquid may have entered the device it must immediately be disconnected This is also valid if the device was exposed to high humidity Also if the device is still running the device must be checked by a specialist if the liquid has reduced any insulation Reduced insulation can cause mortal electrical shock There must never be any objects entering into the device This is especially valid for metal parts If any metal parts like staples or coarse metal chips enter into the device the device must be taken out of operation and disconnected immediately Malfunction or short circuits caused by metal parts may cause mortal injuries HEALTH HAZARD Never look directly into the light source as sensitive persons may suffer an epileptic shock 3 of 26 Keep away children and amateurs Never leave this device running unattended OPERATING PROCEDURES This device is a moving head light for creating decorative effects This product is only allowed to be operated with an alternating voltage of 100 240V 50 60 Hz and was designed for indoor use only This device is designed for professional use e g on stages in clubs bars theatres etc Lighting effects are not designed for permanent operation Consistent operation breaks will ensure that the device will serve you for a long time wi
18. litters must support RDM The number and type of RDM parameters depend on the optional RDM controller being used RDM Parameter ID s Slot 21 22 DISC UNIQUE BRANCH 0x0001 DISC_MUTE 0x0002 DISC _UN_ MUTE 0x0003 SUPPORTED PARAMETERS 0x0050 PARAMETER DESCRIPTION 0x0051 20 of 26 0x0060 DEVICE MODEL DESCRIPTION 0x0080 MANUFACTURER LABEL 0x0081 0x0082 FACTORY DEFAULTS 0x0090 SOFTWARE VERSION LABEL 0x00C0 DMX PERSONALITY 0 006 0 DMX PERSONALITY DESCRIPTION 0x00E1 DMX START _ ADDRESS OxOOFO 0x0120 SLOT DESCRIPTION 0x0121 SENSOR_DEFINITION 0x0200 0x0201 0x0400 0x0500 0x0600 0x0601 IDENTIFY DEVICE 0x1000 0x1001 Reload Default With this function you can restore the factory settings of the device The different settings marked in the table will be set back to the default values shaded DISPLAY_INVERT 4 4 Z lt m A T m U m U m lt O m U J U 0 J gt m m T m m Z lt O lt lt m 5 z 5 5 lt pe z ie O lt O gt z E i O ne C u 6 m Program Play Slave Device With this function you can define the device as a slave You can choose one of three different Slave programs For further information see Edit Chase 21 of 26 Sequence With this function you can run the internal program You can select the desired program under Select Chase You can set the number of steps under Edit Chase You can edit the individu
19. mentioned on bottom of base Make sure the device is fixed properly Ensure that the structure truss to which you are attaching fixture is secure The unit can be placed directly on the stage floor or rigged in any orientation on a truss without altering its operation characteristics see the drawing The fixture base enables mounting in two ways For overhead use mounting height gt 100cm always install an appropriate safety bond Please note for overhead rigging in public or industrial areas a series of safety instructions in this manual need to be followed The operator must inform themselves on the current safety instructions and consider them i i i ll DE 1 pm 9 of 26 The manufacturer cannot be made liable for damages caused by incorrect installations or insufficient safety precautions Install the safety bond by inserting the quick link in the hole on the bottom of the base Pull the safety bond over the trussing system Insert the end in the quick link and tighten the fixation screw The maximum drop distance must never exceed 20cm A safety bond which already holds the strain of a fall or which is defective must not be used again DANGER TO LIFE Before operating for the first time the installation needs to be approved by an expert Omega Holder Clamp Safety Cable Quick Lock Fastener PONA Screw the clamp via a
20. ng or damages and must not rotate unbalanced 4 The electric power supply cables must not show any damages material fatigue e g porous cables or sediments Further instructions depending on the installation spot and usage need to be adhered by a skilled installer and any safety problems have to be removed DANGER TO LIFE Disconnect from power source before starting maintenance operations We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents The lens needs to be replaced when damaged or scratched so that its function is not impaired 24 of 26 The objective lens will require weekly cleaning as fog smoke machine fluid tends to build up residues reducing the light output very quickly The cooling fans should be cleaned monthly The interior of the fixture should be cleaned at least annually using a vacuum cleaner or an air jet There are no serviceable parts inside the device Maintenance and service operations are only to be carried out by authorized dealers Replacing the Fuse Only replace the fuse by a fuse of same type and rating DANGER TO LIFE Before replacing the fuse unplug from power source Procedure Step 1 Remove the fuse holder on the rear panel Step 2 Remove the old fuse from the fuse holder Step 3 Install the new fuse in the fuse holder Step 4 Replace the fuse holder in the housing Should you need any spare parts plea
21. nstructions and warnings detailed in this user manual eS Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems DANGER This device operates on high voltage You can suffer a dangerous electric shock when touching the wires 2 of 26 Safety Instructions Continued If the device has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature Please make sure that there are no obvious transport damages Should you notice any damages on the A C connection cable or on the casing do not take the device into operation and immediately consult your local dealer This device falls under Protection Class The power plug must only be plugged into a Protection Class outlet The voltage and frequency must exactly be the same as stated on the device Wrong voltages or power outlets can lead to the destruction of the device and mortal electrical shock Always plug in the power plug last The power plug must always be inserted without excessive force Make sure that the plug is tightly connected with the outlet Never let the power cord come into contact with other cables Handle the power cord and all connections with the mains with caution Never touc
22. o the Slave unit If set to Slave 2 the slave unit receives Chase Part 2 To Start an Auto Program Proceed as Follows Slave Setting 1 Select Program by pressing Up or Down Press the Enter button to confirm Select Slave by pressing Up or Down Press the Enter button to confirm Press Up or Down to select Slave 1 Slave 2 or Slave 3 Press the Enter button to confirm OF ee Automatic Program Run 1 Select Program by pressing Up or Down Press the Enter button to confirm Select Sequence by pressing Up or Down Press the Enter button to confirm Press Up or Down to select Master or Alone The selection Alone means Stand Alone mode and Master that the device is defined as master Press the Enter button to confirm SO e a Program for Select Chase 1 Select Edit Chase by pressing Up or Down Press the Enter button to confirm Select Select Chase by pressing Up or Down Press the Enter button to confirm Press Up or Down to select Chase Part 1 Chase Part 2 or Chase Part 3 and thus select which a 22 of 26 6 7 Slave program is to be sent Selection Part 1 means that the Slave unit runs the same program as the master units Press the Enter button to confirm Program selection for Edit Program 1 ea Select Edit Chase by pressing Up or Down Press the Enter button to confirm Select Edit C
23. own Press the Enter button then adjust the DMX address by pressing Up or Down Press the Enter button to confirm Light Max Temperature With this function you can set the inside temperature at which the projector will automatically switch the lamp off Press Up or Down to select the maximum internal temperature between 80 C and 139 C Internal temperatures below 90 C are not critical 90 C and more should lead to the lamp being switched off after five minutes Please note that the outside temperature should not exceed 45 C Information Current Time Information With this function you can display the temporary running time of the device from the last power on The display shows XXXX X stands for the number of hours The counter is reset after turning the device off Fixture Life With this function you can display the running time of the device The display shows XXXX X stands for the number of hours Temperature Near Lamp Temp With this function you can display the temperature in the projector head in degrees Celsius Fahrenheit Fan speed With this function you can display the current fan speed The display shows XXXX X stands for Hz Initial status With this function you can display which value the respective channels will start Error channels With this function you can display the channel errors Fixture Model With this function you can display the model number and brand of the fixt
24. rs on several channels at the same time you may see the error messages flash two times and then the fixture will generate a reset signal all the stepper motors will reset If the error messages maintain after performing a reset more than twice only the channels which have errors will not work properly others will work as usual The respective error message will appear after the reset of the fixture if the channels magnetic indexing circuit malfunction sensor failed or magnet missing or the stepping motor is defective or its driving IC on the main PCB The channel feature is not located in the default position after the reset The different error messages are Pan Tilt Color Wheel Prism Rotation Rotating Gobo Wheel Focus CLEANING AND MAINTENANCE The operator needs to make sure that safety related and machine technical installations are inspected by an expert after every four years in the course of an acceptance test The operator needs to make sure that safety relating and machine technical installations are inspected by a skilled person once a year The following points must be considered during the inspection 1 All screws used for installing the devices or parts need to be tightly connected and not corroded 2 There must not be any deformations on housings fixations and installation spots ceiling suspension trussing 3 Mechanically moving parts like axles must not show any traces of wearing e g material abradi
25. s provided are described in the following sections Basic Reload Program Reload Private Reload Default settings are listed in bold MENU SELECTION FUNCTION Light Lamp On Off On Off Lamp On or Off Automatic On Off Lamp On or Off with Power On DMX Control On Off DMX Control On or Off Max Temperature 80 139 C 120 C Set internal 176 282 F 248 F temperature to shut the unit off Activates after 5 minutes Information Time Info Current XXXX Hours Boot Time Fixture Life XXXX Hours Total Run Time Lamp Info Voltage HID Lamp Information Current Power 16 of 26 Software Version 1U01 V 1 0 00 Version of Each IC 2U01 V 1 0 00 All On Off On Off 630 540 Set Reset Pan amp Tilt Shutter Colors Gobos Others Movement Pan Reverse Tilt Reverse Pan Degree Encoders On Off Pan Tilt Mode Stand Smooth Ul Set Mic Sens 3 0 99 60 No Signal Close Hold Auto Music Temperature C F Fahrenheit Celsius Fans Mode Auto High Hibernation OFF 01M 99M 15M Backlight 01 60M 02M Flip Display On Off Display Bright 00 31 10 Brand Show On Off Key Lock On Off Language En fai 4 Fr Sp Users DMX Channel User Mode Mode Standard Extended 8 bit 16 bit User Edit User Max Channel XX Pan CHO1 Calibration 3 Password XXX Color XXX Fixture ID 3 Name Password PID Code Reload Default Basic Reload On Off Program Reload
26. se use genuine parts If the power supply cable of this device becomes damaged it needs to be replaced with a special power supply cable available at your dealer Should you have further questions please contact your dealer 25 of 26 TECHNICAL SPECIFICATIONS Power Consumption DMX Control Channels DMX 512 Connection Sound Control Light Source Color Wheel Fixed Gobo Wheel Maximum PAN Movement 630 or 540 Selectable Dimensions LxWxH 300 x 188 x 435mm 11 8 x 7 4 x 17 1 Weight 12kg 26 5 Ibs Maximum ambient temperature T 45 C 113 F Maximum housing temperature T steady state 60 C 140 F Min distance from flammable surfaces Min distance to lighted object Fuse T 3 15 A 250 V Please note All information is subject to change without prior notice 05 13 2014 26 of 26
27. thout defects Do not shake the device Avoid brute force when installing or operating the device Never lift the fixture by holding it at the projector head as the mechanics may be damaged Always hold the fixture at the transport handles When choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust There should not be any cables lying around Please make sure that the unit cannot be touched or bumped This device must never be operated or stockpiled in surroundings where water splash rain moisture or fog may harm the device Moisture or very high humidity can reduce the insulation and lead to mortal electrical shocks When using smoke machines make sure that the device is never exposed to the direct smoke jet and is installed in a distance of 0 5 meters between smoke machine and device The room must only be saturated with an amount of smoke that the visibility will always be more than 10 meters The ambient temperature must always be between 15 C and 45 C Keep away from direct heat particularly in cars and heaters The relative humidity must not exceed 50 with an ambient temperature of 45 C This device must only be operated in an altitude between 20 and 2000 m over sea level Never use the device during thunderstorms Over voltage could destroy the device Always disconnect the device during thunderstorms me his symbol determines the minimum distance from light
28. uarantee becomes void Furthermore any other operation may lead to dangers like short circuit burns electric shock crashing etc 4 of 26 PRODUCT FEATURES amp SPECIFICATIONS Light Colors Gobos Features Display Power Light source Osram Sirius HRI 132W discharge lamp Lamp life 10 000 hours Luminous Flux 6200 lumen 354200 lux 5m Control Remote on off via DMX Ballast switching mode power supply Beam angle 2 Pan 630 2 8 sec or 540 2 0 sec Tilt 265 1 8 sec 3 phase motor for fast and quiet movement 16 bit resolution Auto repositioning 14 open interchangeable indexable and bidirectional rainbow effect Color bounce Outside 13 8mm inside 6mm 17 open static gobos Real indexable and gobo shaking Distinctive gobo animation effect DMX channels 13 16 10 12 Color wheel 14 White Static gobo wheel 17 Open Motorized focus Full range 0 100 dimmer Various strobe Effect wheel with rotating 8 facet prism RDM function to change DMX address display flip X Y Reverse and more RDM read voltage current power consumption of lamp Software upgrade via DMX Hibernation when lost DMX for preset time Indicate temperature info of base arm and lamp Fan speed auto change according to temperature 2 4 LCD display with English Chinese French Spanish menu Auto lock Flip Back up communicating IC Max power consumption 250W PowerCon in and out Power supply Electronic a
29. ure Software version With this function you can display the software version of each IC 1 Select Software ver by pressing Up or Down 18 of 26 2 Press the Enter button The display shows e g 1001 VX X XX X X XX stands for the version number Set Reset With this function you can reset the device via the Control Board You can select the different Reset functions by pressing Up or Down Movement PAN Reverse With this function you can reverse the pan movement TILT Reverse With this function you can reverse the tilt movement PAN Degree With this function you can select the pan degree 1 Select PAN degree by pressing Up or Down 2 Press the Enter button the display shows 540 3 Press Up or Down to select the desired degree between 540 and 630 4 Press the Enter button to confirm Automatic PAN TILT calibration With the function Encoders you can calibrate the pan tilt movement to the correct starting position Adjust PAN TILT speed With this function you can define the pan tilt soeed You can select one of two different modes UI Set Mic Sensitivity With this function you can select the desired microphone sensitivity between 0 and 99 1 Select Mic Sens by pressing Up or Down 2 Press the Enter button 3 Press Up or Down to select the desired sensitivity 4 Press the Enter button to confirm No DMX Status With the function No Signal you can set differ
30. uto ranging Input voltage range 100 240V 50 60Hz Dimension and Weight 5 of 26 Fixture 300X188X435MM 12 x 7 5 x 17 Packing 510X370X270MM 20 x 15 x 11 Net Weight 10KG 22 Ibs Gross Weight 12KG 26 4 Ibs OVERVIEW 6 of 26 10 11 12 13 14 15 16 17 18 Objective lens Arm Base Handle Wireless indicator Display Microphone Left button Down button Enter button Up button Right button 3 PIN DMX input socket 3 PIN DMX output socket Power input Power output Fuseholder Power switch INSTALLATION Installing Replacing the Lamp DANGER TO LIFE Only install lamp with the device switched off and disconnected from power For the installation you need one Osram Sirius HRI 132W discharge lamp The lamp must only be changed when wearing appropriate protective clothing protection glasses protection gloves helmet with sight leather apron CAUTION The lamp needs to be replaced when damaged or deformed due to heat The lamp life given by the manufacturer must never be exceeded This is why you need to take notes on the operational time of the lamp or check the operating hour meter regularly and replace the lamp in time Keep exchanged lamp in a protective container and remove accordingly During the operation the lamp reaches temperatures of up to 600 C Before replacing the lamp disconnect power and let the lamp cool down approx 10 minutes
Download Pdf Manuals
Related Search