Installation Operation Manual
Contents
1. Main Burner Injector y Pilot Burners 1 Carry out the following 2 Remove pilot injectors and replace with correct Lead to piezo igniter Unscrew and remove piezo igniter Slacken gas supply tube at gas control end Disconnect gas supply tube to pilot burner size injectors as shown in Gas Specifications Tables at rear of this section Re connect the following e Gas supply tube to pilot burner e Tighten gas supply tube at gas control end e Refit piezo igniter e Re connect lead to piezo igniter Pilot Securing Screws Low Fire Adjustment 12 11 Set burner low fire adjustment Low fire screw should be screwed fully In then unscrewed by measurement shown in Gas Specifications table at end of this section Low Fire Adjustment Screw Low Fire Screw should be sealed with coloured paint on completion of low fire adjustment 1 Refit control panel 2 Refit gas control knob Part 6 Gas Conversion Gas Regulator NOTE The gas regulator supplied is convertible between Natural Gas and LP Gas but it s outlet pressure is fixed ex factory and is NOT to be adjusted NAT Gas LPG Butane Only NOTE Pin rotated for Natural Gas NOTE Pin rotated for LPG Town Gas Only Cap Nut 1 Remove slotted cap from regulator2. Piezo Igniter Gas Control Knob O OFF Position 2 Pilot Burner A HIGH Flame 2 LOW Part5 Cleaning and Maintenance General CAUTION Always turn off the gas at the main gas supply before cleaning This appliance is not waterproof Do not use water jet spray to clean interior or exterior of this appliance e achieve the best results cleaning must be regular and thorough and all controls and mechanical parts checked and adjusted periodically by a qualified service person e f any small faults occur have them attended to promptly Don t wait until they cause complete breakdown It is recommended that the appliance is serviced every 6 months e Clean the griddle toaster regularly A clean appliance looks better will last longer and will perform better Carbonised grease on the surface or on the griddle plate will hinder the transfer of heat from the cooking surface to the food This will result in loss of cooking efficiency DO NOT use water on the griddle plate while this item is still hot as warping and cracking may occur Allow the griddle plate to cool down before cleaning NOTE e DO NOT use abrasive detergents strong solvents or caustic detergents as they could corrode or damage the griddle toaster e n order to prevent the forming of rust on the griddle plate Steel Plate ensure that any detergent or cleaning material has been completely removed
3. 2 Turn On gas supply and appliance 3 Adjust pressure adjusting screw to achieve correct burner operating pressure NOTE Measure operating pressure at manifold test point with two burners operating at High Flame setting 4 Screw cap nut back onto regulator Gas Type Identification Label 1 On completion of gas conversion replace gas type identification label located at Rear of appliance above gas connection Beside the rating plate Commissioning Before leaving the installation 1 Check all gas connections for leakage using soapy water or other gas detecting equipment WARNING DO NOT USE A NAKED FLAME TO CHECK FOR GAS LEAKAGES 2 Carry out a Commissioning check of appliance as shown in Installation Section of this manual 3 Ensure any adjustments done to components that have adjustments settings paint sealed are to be re sealed NOTE If it is not possible to get appliance to operate correcily shut Off the gas supply and contact supplier of this appliance 12 Part 6 Gas Conversion Gas Specifications Australia e e LP Gas Propane Main Burner Injectors 2 10mm 1 30mm Pilot Burner Injectors 0 35 0 23 Low Fire Adjustment 1 turn out 1 2 turn out ccw Burner Operating Pressure 1 0 kPa 2 5 kPa Main Burner Aeration Shutter Fully Open Fully Open Gas Regulator Cap Screw New Zealand at Gas MU NNNM Main Burner In
4. Cobra Gas Griddle Toaster Model CT6 INSTALLATION AND OPERATION MANUAL CE 228009 6 MANUFACTURED BY Moffat Limited Christchurch New Zealand INTERNATIONAL CONTACTS AUSTRALIA Moffat Pty Limited E Mail vsales moffat com au Main Office tel 61 03 9518 3888 fax 61 03 9518 3833 Service tel 1800 622 216 Spares tel 1800 337 963 Customer Service CANADA Serve Canada tel 1800 335 315 fax 1800 350 281 Web www servecanada com E Mail info servecanada com Sales tel 800 551 8795 Toll Free Service tel 800 263 1455 Toll Free NEW ZEALAND Moffat Limited Web www moffat co nz E Mail sales moffat co nz Main Office tel O800 663328 UNITED KINGDOM Blue Seal Web www blue seal co uk E Mail sales blue seal co uk Sales tel 44 121 327 5575 fax 44 121 327 9711 Spares tel 44 121 322 6640 fax 44 121 327 9201 Service tel 44 121 322 6644 UNITED STATES fax 44 121 327 6257 Moffat Web www moffat com Sales tel 800 551 8795 Toll Free tel 1 336 661 1556 fax 1 336 661 9546 Service tel 800 858 4477 Toll Free tel 1 366 661 1556 fax 1 336 661 1660 REST OF WORLD Moffat Limited Web www moffat co nz E Mail export moffat co nz The reproduction or copying of any part of this manual by any means whatsoever is strictly forbidden unless authorized previously in writing by the manufacturer In line wi
5. e Remove the 2 screws holding shaft plate to gas control body and remove control shaft and plate Note orientation of shaft for correct re assembly f Using needle nose pliers or similar pull out gas control spindle again noting its orientation g Apply a suitable high temperature gas cock grease or lubricant such as ROCOL A S P Anti scuffing paste Dry Moly Paste to the outside of the spindle h Replace spindle and re assemble the gas control in reverse order i Refit the control panel to the appliance and secure with 2 screws Refit the knobs to the gas control valve spindles Two Screws Spindle Part Gas Conversion Gas Conversion Procedure CAUTION Ensure that the unit is isolated from the gas supply before commencing servicing NOTE e These conversions should only be carried out by qualified service persons All connections must be checked for leaks before re commissioning the appliance e For all relevant gas specifications refer to the table at the end of this section Main Burners 1 Remove the following Gas control knobs Control Panel Disconnect electrical connection lead from rear of piezo igniters 2 Remove main burner injectors and replace with correct size injectors as shown in Gas Specifications Tables at rear of this section Thermocouple Connection x WE Eun
6. appliance is installed correcily and that operation is correct before use Installation shall comply with local gas health and safety requirements This appliance shall be installed with sufficient ventilation to prevent the occurrence of unacceptable concentrations of health harmful substances in the room the appliance is installed in Cobra Series Gas Griddle Toasters are designed to provide years of satisfactory service and correct installation is essential to achieve the best performance efficiency and trouble free operation This appliance must be installed in accordance with National installation codes and in addition in accordance with relevant National Local codes covering gas and fire safety Australia AS 5601 Gas Installations New Zealand NZS 5261 Gas Installation United Kingdom Gas Safety Installation and Use Regulations 1998 BS6173 Installation of catering Appliances BS5440 1 amp 2 Installation Flueing amp Ventilation Ireland 5 820 Non Domestic Gas Installations Installations must be carried out by qualified service persons only Failure to install equipment to the relevant codes and manufacturer s specifications shown in this section will void the warranty Components having adjustments protected e g paint sealed by manufacturer are only to be adjusted by an qualified service agent They are not to be adjusted by the installation person Unpacking e Remove all packaging and
7. service persons should be ignition can be viewed through openings in the used to carry out installation servicing or control panel gas conversion operations 3 Hold in the gas control knob for approximately 10 seconds then release The pilot burner should This appliance is for professional use and is only to be used by qualified people Components having adjustments protected e g paint sealed the remain alight If not repeat Items 1 to 3 manufacturer should not be adjusted by 4 Repeat Items 1 to 3 to light the second pilot the user operator burner 5 FULL flame can now be achieved by rotating the gas control knob anti clockwise to the first 1 Cobra Gas Griddle Toasters have been stop designed to provide simplicity of operation and 6 LOW flame can be achieved by depressing 0 protection rotating the gas control knob fully anti 2 Improper operation is therefore almost clockwise impossible however bad operation practices can reduce the life of the appliance and Using the Griddle produce a poor quality product To use this gas griddle toaster correctly please read the l Light the pilot burners as shown above following sections carefully before use 2 Turn the gas controls to the FULL flame position If starting from a cold start allow the griddle plate to preheat for 10 minutes before using e Using the Griddle 3 Place the product to be cooked onto the griddle plate 4 Forint
8. that this is correct for the gas supply the appliance is being installed for The gas conversion procedure is detailed in the Gas Conversion Instruction Sheet for this appliance b Supply Pressure required for this appliance is shown in the Specifications section of this manual Check the gas supply to ensure that adequate supply pressure exists C Input Rate of this appliance is also stated on the Rating Plate fitted to the inside of the right hand side panel below the middle shelf and in the Specifications section of this manual The input rate should be checked against the available gas supply line capacity Particular note should be taken if the appliance is being added to an existing installation NOTE It is important that adequately sized piping runs directly to the connection joint on the appliance with as few tees and elbows as possible to give maximum supply volume 3 Fit the gas regulator supplied into the gas supply line as close to the appliance as possible NOTE The gas pressure regulator provided with this appliance is convertible between Natural Gas and LPG as per the Gas Conversion Section in this manual Ensure the regulator is converted to the correct gas type that the appliance will operate on The regulator outlet pressure is fixed ex factory for the gas type that the regulator is converted to and it is NOT to be adjusted The regulator connections are 2 BSP female The connection to th
9. transit protection from the appliance including all protective plastic coating from the door outer panel and exterior stainless steel panels e Check equipment and parts for damage Report any damage immediately to the carrier and distributor e Report any deficiencies to the distributor who supplied the appliance e Check that the available gas supply is correct to that shown on the rating plate located on the right hand side panel beneath the middle shelf e Check that the following parts have been supplied with the appliance Enamelled Crumb Tray Toasting Rack Toasting Rack Tray St Steel Grease Drawer Adjustable Legs Gas Regulator gt Location l Installation must allow for a sufficient flow of fresh air for the combustion air supply Combustion Air Requirements Natural Gas LPG Propane 10 m hr minimum 9 m hr minimum 2 Installation must include adequate ventilation means to prevent dangerous build up of combustion products 3 Position the appliance in its approximate working position 4 All air for burner combustion is supplied from underneath the appliance The legs must always be fitted and no obstructions placed on the underside or around the base of the appliance as obstructions will cause incorrect operation and or failure of the appliance o Components having adjustments protected e g paint sealed by manufacturer are only to be adjusted by a qualified service a
10. 3 018067 Pilot Injector Town Gas 0 60 019428 Thermocouple 230608 Gas Control Knob 230586 Piezo Igniter 228047 HT Lead 250mm General 227007 Toasting Rack 227006 Side Racks 229987 Crumb Tray Enamelled 230289 Grease Tray 230578 Adjustable Legs 150mm 229674 Rear Roller Assy Gas Regulators Gas Type _ PartNo Description 228533 e BSP F F Convertible Nat Gas LPG Butane Town Gas 230185 3 4 BSP F F Adjustable Gas Conversion Kits Gas Convert to LPG Propane 231553 231554 231555 231578 15
11. Sheet for this appliance for further details All Other Markets LP Gas Butane Input Rating N H G C 42 MJ hr 42 MJ hr Supply Pressure 2 75 4 50 kPa 2 75 4 50 kPa Comer Operating 2 50 kPa 4 2 50 kPa ressure Gas Connection 15 BSP Male Input Rating N H G C 42 MJ hr 42 MJ hr Supply Pressure 1 13 3 40 kPa 0 75 1 50 kPa Burner Operating Pressure 1 00 kPa 0 63 kPa Gas Connection 1 2 BSP Male NOTE e Burner operating pressure is measured at the manifold test point with both burners operating at the High Flame setting e NAT LPG amp Butane Only Operating pressure is ex factory set and is not to be adjusted apart from when converting between gasses if required e TOWN GAS Only Burner operating pressure is to be adjusted using the Town Gas adjustable gas regulator supplied e Refer to the Gas Conversion and Specifications section of this manual for further details Gas Connection Gas supply connection point is located 130mm from the right hand side of the appliance 32mm from the rear and 655mm from the floor and is accessed from beneath the appliance Connection is 1 2 BSP male Part2 Specifications Dimensions CT6 Gas Griddle Toaster 600mm 800 70 GAS v Iz LO LO O En O 9 100 229 Part 3 Installation Installation Requirements NOTE It is most important that this
12. after each cleaning The appliance should be switched on briefly to ensure the griddle plate becomes dry Oil or grease should be spread over the griddle surface in order to form a thin protective greasy film To keep your griddle toaster clean and operating at peak efficiency follow the procedures shown opposite After Each Use CAUTION Always ensure that an even pressure is applied over the whole surface of the scraper tool when using on the flat surface of the griddle toaster to prevent scoring of the surface NEVER bang the sharp edge of the scraper tool on the flat surface of the griddle as this will damage the finish and invalidate the warranty 1 Clean the griddle with a scraper tool to remove any food debris 2 Always ensure that the scraper tool blades are changed regularly to ensure that the scraper tool works efficiently and prevents damage to the griddle plate surface Daily Cleaning 1 The crumb tray grease drawer should be checked and emptied frequently to prevent overflow and spillage Remove the grease drawer while still warm so that the grease is in a liquid state Empty any grease from the drawer and wash thoroughly in the same manner as any cooking utensil 2 Remove the crumb tray and empty out the contents Wash thoroughly in the same manner as any cooking utensil 3 Thoroughly clean the splash back interior and exterior surfaces of the range with hot water a detergent solution an
13. allow cleaning of the front control panel b Baked on deposits or discolouration may require a good quality stainless steel cleaner or stainless steel wool Always apply cleaner when the appliance is cold and rub in the direction of the grain c Toremove any discolouration use an approved stainless steel cleaner or stainless steel wool Always rub in the direction of the grain d Dry all components thoroughly with a dry cloth and polish with a soft dry cloth 10 Periodic Maintenance NOTE All maintenance operations should only be carried out by a qualified service person To achieve the best results cleaning must be regular and thorough and all controls and mechanical parts should be checked and adjusted periodically by a qualified service person If any small faults occur have them attended to promptly Don t wait until they cause a complete breakdown It is recommended that the appliance is serviced every 6 months Gas Control Valve Re Greasing The gas control valve should be dismantled and greased every 6 months to ensure the correct operation of the gas control valve To carry out this operation a Remove the gas control knobs from the gas tap spindles by pulling the knobs away from the control panel b Remove the drip tray from the appliance c Remove the two screws on the underside of the control panel securing the control panel to the hob d Remove the control panel from the front of the appliance
14. country WARNING IMPROPER INSTALLATION ADJUSTMENT ALTERATION SERVICE OR MAINTENANCE CAN CAUSE PROPERTY DAMAGE INJURY OR DEATH READ THE INSTALLATION OPERATING AND MAINTENANCE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING OR SERVICING THIS APPLIANCE WARNING INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE USER SMELLS GAS ARE TO BE POSTED IN A PROMINENT LOCATION THIS INFORMATION SHALL BE OBTAINED BY CONSULTING THE LOCAL GAS SUPPLIER WARNING GREAT CARE MUST BE TAKEN BY THE OPERATOR TO USE THE EQUIPMENT SAFELY TO GUARD IT AGAINST RISK OF FIRE THE APPLIANCE MUST NOT BE LEFT ON UNATTENDED IT IS RECOMMENDED THAT A REGULAR INSPECTION IS MADE BY A COMPETENT SERVICEMAN TO ENSURE CORRECT AND SAFE OPERATION OF YOUR APPLIANCE IS MAINTAINED DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPOURS OR LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION CAUTION This appliance is For professional use and is to be used by qualified persons only Only Qualified service persons are to carry out installation servicing and gas conversion operations Components having adjustments protected e g paint sealed by the manufacturer should not be adjusted by the user operator DO NOT operate the appliance without the legs supplied fitted Part2 Specifications Model Covered in this Specification CT6 Gas Griddle Toaster General A comme
15. d a soft scrubbing brush 4 Brush the griddle surface with a soft bristled brush Any carbon deposits should be removed using the supplied scraper tool followed by wiping with a cloth to prevent accumulation of food deposits o Clean the control panel with a damp cloth light ly moistened with a solution of mild detergent and water Wipe dry with a clean dry cloth 6 Dry the griddle toaster thoroughly with a dry cloth and polish with a soft dry cloth Weekly Cleaning NOTE e If the griddle toaster usage is very high we recommend that the weekly cleaning procedure is carried out on a more frequent basis e Ensure that protective gloves are worn during the cleaning process e DO NOT use harsh abrasive detergents strong solvents or caustic detergents as they will dam age the griddle toaster and burners e DO NOT use water on the griddle plate while it is still hot as warping may occur Allow these items to cool and remove for cleaning Part5 Cleaning and Maintenance Griddle Plate NOTE In order to prevent the forming of rust on the griddle plate ensure that all detergent and cleaning material has been entirely removed after each cleaning process The appliance should be switched on briefly to ensure the griddle plate becomes dry Oil or grease should be spread over the griddle surface in order to form a thin protective greasy film a Remove and clean the grease collection drawer frequently to prevent over spil
16. e appliance is 2 BSP male Refer to the Specifications section for the gas supply location dimensions NOTE A Manual Isolation Valve must be fitted to the individual appliance supply line 4 Correctly locate the appliance into its final operating position and using a spirit level adjust the legs so that the unit is level and at the correct height o Connect the gas supply to the appliance A suitable joining compound which resists the breakdown action of LPG must be used on every gas line connection unless compression fittings are used 6 Check all gas connections for leakages using soapy water or other gas detecting equipment WARNING DO NOT USE A NAKED FLAME TO CHECK FOR GAS LEAKAGES 7 Check that the gas supply pressure is as shown in the Specifications section Gas Supply Requirements tables NOTE The supply pressure to be measured at the manifold test point 8 Light the Main Burners Refer to the Operations Section Using the Griddle Using the Toaster 9 Verify that the supply pressure Is still correct 10 Check that the Main Burner is alight and adjust the low fire adjustment screw on the open burner gas control valves to obtain the desired flame size 11 Check adjust the main burner aeration gap This gap should be set to the dimensions shown in the Gas Specification Tables in Part 6 Gas Conversion Gas Specifications tables Part 3 Installatio
17. ermediate heat position the gas control m knob between the HIGH and LOW positions to Description of Controls achieve the desired heat 5 During idle periods the burners can be turned down to maintain an appropriate griddle plate temperature or the gas controls can be set to the PILOT position as required e Lighting the Pilot Burners e Using the Toaster Using the Toaster 1 Light the pilot burners as shown above 2 If starting from cold set the burners to the FULL flame position and allow 5 minutes preheat before commencing toasting 3 Adjust the rack position to the desired height 4 Place the product on the rack to toast 5 Best toasting results are achieved using the shaded area shown on the diagram opposite 6 With the main burners alight the individually controlled burners can be operated to suit food quantity requirements 7 Each burner is operated by an OFF PILOT HIGH LOW gas control The HIGH position is recommended for most grilling cheese melting functions and the LOW position for a reduced heat setting Vd le wb DAP Optimum Toasting Area NOSSAS X N W AK UL SANT
18. gent They are not to be adjusted by the installation person NOTE Do not obstruct or block the appliances flue Never directly connect a ventilation system to the appliance flue outlet Clearances NOTE Only non combustible materials can be used in close proximity to this appliance Any gas burning appliance requires adequate clearance and ventilation for optimum and trouble free operation The following minimum installation clearances are to be adhered to Combustible Non Combustible Surface Surface LH RH Part 3 Installation Assembly This model is delivered completely assembled Ensure that the legs are securely attached NOTE This appliance is fitted with adjustable feet to enable the appliance to be positioned securely and level This should be carried out on completion of the gas connection Refer to the Gas Connection section Gas Connection NOTE ALL GAS FITTING MUST ONLY BE CARRIED OUT BY A QUALIFIED SERVICE PERSON 1 Cobra Series Gas Griddle Toasters do not require an electrical connection they function totally on the gas supply only 2 lt is essential that the gas supply is correct for the appliance to be installed and that adequate supply pressure and volume are available The following checks should be made before installation a The Gas Type the appliance has been supplied for is shown on coloured stickers located above the gas entry point and next to the rating plate Check
19. ing pressure at the manifold test point with both burners operating at High Flame setting e NAT LPG amp Butane Only Operating pressure is ex factory set and is not to be adjusted apart from when converting between gasses if required e TOWN GAS Only Adjusted Burner operating pressure using the adjustable gas regulator supplied e Refer to information in this section for further details 14 Part 7 Replacement Parts List Replacement Parts List IMPORTANT Only genuine qualified replacement parts should be used for the servicing and repair of this appliance The instructions supplied with the parts should be followed when replacing components For further information and servicing instructions contact your nearest qualified service branch contact details are as shown on the reverse of the front cover of this manual When ordering spare parts please quote the part number and the description as listed below If the part required is not listed below request the part by description and quote model number and serial number which is shown on the rating plate Controls 231558 Burner Griddle Toaster 037210 Burner Injector Natural Gas 2 10mm 037130 Burner Injector LPG 1 30mm 037120 Burner Injector Butane 1 20mm 037380 Burner Injector Town Gas 3 80mm 22 403 Gas Control Valve 019215K Pilot Burner 026488 Pilot Injector Natural Gas 25 00959 019217 Pilot Injector LPG Butane 0 2
20. jectors 2 10mm 1 30mm Gas Regulator Cap Screw LP UK Only Category I2H3P Flue Type Ai Propane 0 exp Main Burner Injectors Dd 2 10mm D 1 30mm Pilot Burner Injectors 0 35 0 23 Low Fire Adjustment 1 2 turn out Burner Operating Pressure 10 mbar 26 mbar Main Burner Aeration Shutter Fully Open Fully Open Gas Regulator Cap Screw NAT LP NOTE Measure burner operating pressure manifold test point with both_burners operating at full setting Operating pressure is ex factory set through the appliance regulator and is not to be adjusted apart from when carrying out gas conversion Refer to Gas Conversion information for details 13 Part 6 Gas Conversion All Other Markets atura e Town Gas Main Burner Injectors 2 10mm 3 80mm Pilot Burner Injectors 0 35 0 60 Low Fire Adjustment 1 turn out C C w 2 turns out c c w Burner Operating Pressure 1 0 kPa 0 63 kPa Main Burner Aeration Shutter Fully Open Fully Open Adjustable Regulator Adjust to Burner Operating Pressure Gas Regulator Cap Screw NAT Main Burner Injectors 1 30mm 1 20mm Pilot Burner Injectors 0 23 Low Fire Adjustment 1 2 turn out c c w Burner Operating Pressure 2 5 kPa Main Burner Aeration Shutter Fully Open Gas Regulator Cap Screw NOTE e Measure burner operat
21. ls b Remove the crumb tray frequently to prevent overfilling the crumb tray c Clean the griddle surface thoroughly with suitable scraper tool Use a griddle stone or a scotch bright pad on the griddle surface for the removal of stubborn or accumulated carbon deposits d Occasionally bleach the griddle plate with vinegar when the plate is cold e Clean with hot water a mild detergent solution and a scrubbing brush Dry all components thoroughly with a dry cloth f The griddle plate should be switched on briefly to ensure that the griddle plate becomes dry A thin smear of cooking oil should be spread over the griddle plate to form a protective film Grilling Toasting Area a Clean the grilling toasting area with a soft cloth and a mild detergent and hot water solution b Baked on deposits or discolouration may require a good quality stainless steel cleaner or stainless steel wool Always apply cleaner when the appliance is cold and rub in direction of grain c Remove the grease drawer and crumb tray clean with a mild anti bacterial detergent and hot water solution using a soft bristled brush Dry the grease drawer and crumb tray thoroughly with a dry cloth Stainless Steel Surfaces a Clean the exterior surfaces of the griddle toaster with hot water a mild detergent solution and a soft scrubbing brush Note that the gas control knobs are a push fit onto the gas control valve spindles and can be removed to
22. n Commissioning The following commissioning checks must be carried out before the Gas Griddle Toaster is handed over for use to ensure that the unit operates correctly and the operator s understand the correct operating procedure l Before leaving the new installation a Check the following functions in accordance with the operating instructions specified in the Operation section of this manual e Light the Pilot Burners e light the Main Burners e Check the Low Fire Burner operation e Check the High Fire Burner operation b Ensure that each operator has been instructed in the areas of correct lighting operation and shutdown procedures for the appliance 2 This manual must be kept by the owner for future reference and a record of Date of Purchase Date of Installation and Serial Number of Unit recorded and kept with this manual These details can be found on the Rating Plate attached to the inner R H side panel beneath the middle shelf NOTE If for some reason it is not possible to get the appliance to operate correctly shut off the gas supply and contact the supplier of this unit Part4 Operation Operation Guide Lighting the Pilot Burners 1 Depress the gas control knob and rotate anti CAUTION clockwise to the PILOT position 2 Whilst holding the control knob depressed press the piezo ignition button adjacent to the gas control knob until the pilot burner ignites Pilot Only Qualified
23. rcial heavy duty gas fired griddle toaster having two tubular burners heating a griddle plate from underneath and providing toasting heat for the toasting rack below Burners are operated by individual control valves and are provided with a piezo ignition permanent pilot incorporating a thermocouple flame failure control Gas Supply Requirements Australia Natural Gas LF Gas Propane Input Rating 42 MJ hr 42 MJ hr Supply Pressure 1 13 3 40 kPa 2 75 4 50 kPa 1 00 kPa 2 50 kPa ressure Gas Connection 1 2 BSP Male New Zealand Natural Gas LP Gas Input Rating 42 MJ hr 42 MJ hr Supply Pressure 1 13 3 40 kPa 2 75 4 50 kPa bel Operanng 1 00 kPa 2 50 kPa ressure Gas Connection 1 2 BSP Male United Kingdom Category Hus Flue Type 1 Nat Gas Propane Heat Input Nominal 11 0 kW 11 0 kW rt TI Gas Rate Nominal 1 16 m3 hr 0 85 kg hr nett Reduced 0 63 m3 hr 0 44 kg hr Supply Pressure 20 mbar 37 mbar 10 mbar 26 mbar Burner Operating Pressure Gas Connection 1 2 BSP Male NOTE Measure burner operating pressure at manifold test point with all burners operating at full setting The operating pressure is ex factory set through the appliance regulator and is not to be adjusted apart from when converting between gases if required Refer to Gas Conversion Instruction
24. th policy to continually develop and improve its products Moffat Ltd reserves the right to change the specifications and design without prior notice Copyright Moffat Ltd April 2014 CT6 Gas Griddle Toaster Part 1 TER PT 2 Part 2 SD ECC allons od 3 Part 3 DPS CINCH Means ee cates 5 Part 4 QOD SITIO j E TI a TUTUP 8 Part 5 Cleaning and Maintenance cccccccccccccccceceee 9 Part 6 Gas Conversion ina 11 Part 7 Replacement Parts USA ii AAA de 15 Part 1 Introduction We are confident that you will be delighted with your Cobra Series Gas Griddle Toaster and it will become a most valued appliance in your commercial kitchen To ensure you receive the utmost benefit from your new Cobra Series Appliance there are two important things you can do Firstly Please read this instruction book carefully and follow the directions given The time taken will be well spent Secondly If you are unsure of any aspect of the installation instructions or performance of your appliance contact your Cobra Series appliance dealer promptly In many cases a phone call could answer your question CE Only These instructions are only valid if the country code appears on the appliance If the code does not appear on the appliance refer to the supplier of this appliance to obtain the technical instructions for adapting the appliance to the conditions for use in that
Download Pdf Manuals
Related Search