XILICA Audio Design
Contents
1. DCP 3060 Loudspeaker Management System User Manual Pe XILICA Audio Design UT ION DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL Important Safet The lightning flashwith arrowhead symbol within anequilateral triangle is intendedto alert theuser to the presence of uninsulated dangerous voltage withinthe product s enclosurethat may be of sufficient magnitudeto constitute a risk to persons The exclamation point within an equilateral triangle isintended to alert the userto the presence of important operating and maintenance servicing instructions in theliterature accompanying the appliance Instructions 1 READ THESE INSTRUCTIONS All the safety and operating instructions should be read before the product is operated 2 KEEP THESE INSTRUCTIONS The safety and operating instructions should be retained for future reference 3 HEED ALL WARNINGS All warnings on the product and in the operating instructions should be adhered to 4 FOLLOW ALL INSTRUCTIONS All operating and use of instructions should be followed 5 DO NOT USE THIS APPARATUS NEAR WATER Do not use the product near water For example near a bathtub washbowl kitchen sink or laundry tub in a wet basement or near a swimming pool and the like 6 CLEAN ONLY WITH DRY CLOTH Unplug t2. Ranges from 20 to 20 000Hz in either 1Hz steps or 1 36 octave steps The frequency steps can be selected in the O1 XXXXXX XOver FROL 1000Hz w lt O 3 O gt E SLPL Filter Slope of low frequency crossover point high pass Ranges from 6 to 48dB octave If the selected Filter Type is Linkritz Riley the available slopes are 12 24 36 48 dB octave O1 XXXXXX XOver SLPL 24dB FTRH Filter Type of high frequency crossover point low pass O1 XXXXXX XOver FTRH Off FRQH Filter cut off Frequency of high frequency crossover point low pass O1 XXXXXX XOver FROH 1000Hz SLPH Filter Slope of high frequency crossover point low pass O1 XXXXXX XOver SLPH 24dB DCP 3060 User s manual Page 14 Filter Low crossover High crossover configuration point point None FTRL Off FTRH Off Highpass FTRL not Off FTRH Off FROL Lowpass FTRL Off FTRH not Off E FRQH Bandpass FTRL not Off FTRH not Off A FRQL FRQH Limit Output Limter e THRESH Limit Threshold Ranges from 20 to 20dBu in 0 5dB steps O1 XXXXXX Limit THRESH 20 0dB e ATTACK Attack time Ranges from 0 3 to ims in 0 1ms steps then ranges from 1 to 100ms in 1ms steps O1 XXXXXX Limit ATTACK 10ms e RELEASE Release time Can be set at 2X 4X 8X 16X or 32X the attack time O1 XXXXXX Limit RELEASE 8X DCP 3060 User s manual Page 15 Source Input Source e 1 2 3
3. Mute Unmute input and output channels When an input channel is muted a red LED will come on for indication 2 Gain Menu keys Selects the corresponding channel for the LCD menu display and is acknowledged by a green LED The last modified menu will be displayed on the LCD Linking multiple channels is accomplished by pressing and holding the first channel key then pushing the other desired channels This eases programming for same parameters across multiple channels Multiple Inputs can be linked together and multiple outputs can be linked together Inputs and Outputs are linked separately 3 Peak Level LED Indicates the current peak level of the Signal Signal 12dB 6dB 3dB Over Limit The Input Over LED references to the device s maximum headroom The Output Limit LED references to the threshold of the limiter 4 LCD Shows all the necessary information to control the unit 5 Rotary Thumb Wheel Changes parameter data values The wheel has travel velocity sensing which ease large incremental data modifications For modifying delay and frequency 1 Hz resolution pressing the Speed key simultaneously will increment decrement the data value by 100X 6 Menu Control keys There are 6 menu keys lt lt Menu Menu Down Menu gt gt Menu Up lt lt Cursor Cursor Down Cursor gt gt Cursor Up Enter Sys Speed and Exit The functions of each key is explained below DCP 3060 User s manual Page 7 lt lt Menu
4. Input channel source for the current output channel Can be set to enable the input source On or disable it Off If more than one input source are enabled they will be added together as the source for the current output channel O1 XXXXXX Source In1 On O1 XXXXXX Source In2 0ff O1 XXXXXX Source In3 0ff Ch Name Channel Name e Referto the Input Menus for details DCP 3060 User s manual Page 16 6 3 System Menus The System Menus allow the user to control and change parameters that are related to the system behavior and general operation It can be accessed by pressing the Sys key in the main menu when no Input Output or System Menu is activated All System Menus require the Enter key to be pressed for the selected action Recall Program Recall The DCP 3060 has a built in non volatile memory that can store up to 30 different program setups A program can be recalled using this menu e PROG Program Number to be recalled Only first 8 characters of the program name is displayed O1 XXXXXX Recall PROG 01 XXXXXXXX Store Program store The DCP 3060 has a built in non volatile memory that can store up to 30 different program setups A program can be stored using this menu The old program with the same program number will be replaced Once the program is stored in the flash memory it can be recalled at a later time even after power down e PROG Program Number for the current data to be stored O1 XXXXX
5. 01 DEVICE 1 FREQ MODE Selects the frequency control mode for EQ and crossover filters Can be 36 steps octave or All Frequencies 1 Hz resolution O1 XXXXXX Generl FREQ MODE A11 DELAY UNIT ms ft or m O1 XXXXXX Generl DELAY UNIT ms DEVICE Assigns the device ID from 1 to 16 This ID is useful when a network of more than 1 unit is present O1 XXXXXX Generl DEVICE 1 Security Security Lock The DCP 3060 enables the user to secure the unit and prevent undesired changes in the setup In order to lock unlock the unit the user must enter the correct password PASSWORD The password of the DCP 3060 is 4 characters in length The user can change it via the PC application software The factory default of a new unit does not require a password O1 XXXXXX Secure PASSWORD XXXX DCP 3060 User s manual Page 19 7 0 Quick Reference Parameters Menu Ped Min Max Steps Units lt lt Menu gt gt lt lt Cursor gt gt Level Signal LEVEL 40 15 0 25 dB Polarity Signal POL Delay Signal DELAY 0 2 400 1 21us steps EQ Number EQ EQ 1 6 1 EQ Level EQ LEVEL 30 15 0 25 dB EQ Frequency EQ FREQ 20 20 000 1 Hz EQ Bandwidth EQ BW 2 50 0 01 Octave Crossover Low XOver FTRL Off Butterworth Linkwitz Riley Bessel Crossover Low XOver FRQL 20 20 000 1 Hz Crossover Low XOver SLPL 6 48 6 dB octave Crossover High XOver FTRH Off Butterworth Link
6. 16 APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING AND NO OBJECTS FILLED WITH LIQUIDS SUCH AS VASES SHALL BE PLACED ON THE APPARATUS DCP 3060 User s manual Page 3 Table of Contents Table of Coments san RR na 4 e A 5 20 FRAME artes ts ces cscs ainda ter ii idos 6 3 0 Front Panel Functions wiscicssscisesissrcovecascasccnssecsmntecessexnanes 7 4 0 Rear Panel Functions 0ooonccccoonnanncccnconnnnnnnnnnnnnannnnnnnnnanans 9 5 0 Powering Up the Device oocccccccooonnnccccononnnnnnnnnnnnnnnnns 10 6 0 Operating the Device oooooocccccccnnnccoccocennnaannnonrenanaannnnnnnnas 11 6 1 Mpui A 11 6 2 Ouiput MENUS ssaanacieananesanassbainasesriniance ninhada 13 6 3 System Men s carrasco 17 7 0 Quick RRETSI SINCE iiicnaciiccccceciessesretticcsecceavenasesccteennacenvenaste 20 8 0 PC Control Software sccioiciincanicaniniaia noria 21 30 SPeECIICANONS sanada 22 10 0 MI do jo ricerca DDR RAR SR 24 DCP 3060 User s manual Page 4 1 0 Introduction The DCP 3060 is a complete 3 input 6 output digital loudspeaker management system designed for the touring or fixed sound installation markets The absolute latest in available technology is utilized with 32 bit 40 bit extended floating point processors and high performance 24 bit Analog Converters The high bit DSP prevents noise and distortion induced by truncation errors of the commonly used 24 bit fixed point devices A complete set of parameters include I O levels delay polarit
7. EY EXIT FROM THE APPARATUS 11 ONLY USE ATTACHMENTS ACCESSORIES SPECIFIED BY THE MANUFACTURER 12 USE ONLY WITH CART STAND TRIPOD BRACKET OR TABLE SPECIFIED BY THE MANUFACTURER OR SOLD WITH THE APPARATUS WHEN A CART IS USED USE CAUTION WHEN MOVING THE CART APPARATUS TO AVOID INJURY FROM TIP OVER Do not place this unit on an unstable cart stand tripod bracket or table The unit may fall causing serious injury to someone and serious damage to the appliance A unit and cart combination should be moved with care Quick stops excessive force and uneven surfaces may cause the product and cart combination to overturn 13 UNPLUG THIS APPARATUS DURING LIGHTNING STORMS OR WHEN UNUSED FOR LONG PERIODS OF TIME For added protection for this unit during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the antenna or cable system This will prevent damage to the unit due to lightning and power line surges 14 REFER ALL SERVICING TO QUALIFIED SERVICE PERSONNEL SERVICING IS REQUIRED WHEN THE APPARATUS HAS BEEN DAMAGED IN ANYWAY SUCH AS WHEN THE POWER SUPPLY CORD OR PLUG IS DAMAGED LIQUID HAS BEEN SPILLED OR OBJECTS HAVE FALLEN INTO THE APPARATUS THE APPARATUS HAS BEEN EXPOSED TO RAIN OR MOISTURE DOES NOT OPERATE NORMALLY OR HAS BEEN FROPPED 15 WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE
8. Menu gt gt lt lt Cursor Cursor gt gt Enter Sys Speed Exit Previous menu screen Next menu screen Previous cursor in the menu screen Next cursor in the menu Screen Enter is used only in the System Menu to proceed with selected actions Sys enters the System Menu from the main menu Speed modifies delay and frequency 1 Hz resolution mode data values by 100X Exit to the Main Menu DCP 3060 User s manual Page 8 4 0 Rear Panel Functions 1 Main Power Connects via a standard IEC socket A compatible power cord is supplied with the unit The voltage input is either 115VAC or 230VAC and is clearly specified on the unit Voltage requirement has to be stated upon ordering 2 Main Fuse T200mA 250V Slow blow type 3 Power switch Controls power On Off 4 RS232 a standard female DB9 socket A straight through cable is required for PC connection 5 Option slot Option slot for future use 6 XLR input and outputs Separate 3 pin XLR connectors are provided for each audio input and output The device s output stage employs the balanced impedance topology All I O connectors have pin 1 as ground shield pin 2 as and pin 3 as DCP 3060 User s manual Page 9 5 0 Powering Up the Device e After powering up the unit the following initialization screen is displayed on the LCD XILICA DCP 3060 e The initialization process takes about 8 seconds and during that period the unit boots and di
9. Owner s complete name daytime phone number return street address and return authorization number 2 The serial number of the product being returned and a copy of the retail sales receipt if possible 3 A complete description of the problem s experienced including a brief description of how the equipment is being used and other equipments involved DCP 3060 User s manual Page 24 User Manual v4 01 Apr 2005 XILICA Audio Design 88 Oxford Street Richmond Hill Ontario Canada L4C 4L5 Phone 905 770 0055 Fax 905 770 2984 www xXilica com
10. X Store PROG 01 e NAM Program Name allows a maximum length of 12 characters O1 XXXXXX Store NAM XXXXXXXXXXXX DCP 3060 User s manual Page 17 Config Device Configuration SYSTEM SETUP MENU Config MODE 2 Way e MODE configures the mode of operation Mode Outi Out2 Out3 Out4 Out5 Out6 None Any Any Any Any Any Any Stereo 2 Way Ini Int In2 In2 Any Any Stereo 3 Way Inf Int Int In2 In2 In2 The unit assigns the Input source for the corresponding outputs when the Mode of Configuration is selected The crossover point parameters like the filter type cut off frequency and slope have to be configured manually in the Xover Menu in each Output menu Note The configuration mode configures the input sources when selected The user can change the source afterwards if desired It does not keep the configuration in memory Copy Copy channels Copy Channels from the source to the target When the Source and Targets are both Inputs or Outputs all audio parameters will be copied When one of the Source or the Target is an input while the other is an output only the Level Polarity Delay and EQ are copied e SOURCE Channel to be copied from O1 XXXXXX Copy SOURCE Inl e TARGET Channel to be copied to O1 XXXXXX Copy TARGET In2 DCP 3060 User s manual Page 18 General General system parameters SYSTEM SETUP MENU General FREQ MODE All Freq DELAY UNIT
11. e 11 EQ EQ parameters EQ Selects one of the 6 available Equalizers I1 XXXXXX EQ EQ 1 LEVEL EQ level gain Ranges from 30 00dB to 15 00dB in 0 25dB steps I1 XXXXXX EQ LEVEL 0 00dB FREQ EQ center frequency Ranges from 20 to 20 000Hz in either 1Hz steps or 1 36 octave steps The sampling rate and the frequency steps can be selected in the System Menu I1 XXXXXX EQ FREQ 1000Hz BW EQ Bandwidth Ranges from 0 02 to 2 50 octaves in steps of 0 01 octave steps for PEQ The Q value is automatically shown beneath the octave value For Lo SIf or Hi Shf it is either 6 or 12dB Oct I1 XXXXXX EQ BW 0 33 Q 4 36 Type Type of EQ The types can be parametric PEQ Lo shelf Lo shf and Hi shelf Hi shf I1 XXXXXX EQ Type PEQ Ch Name Channel Name I1 XXXXXX ChName NAME XXXXXX e Name Channel name It is 6 characters in length DCP 3060 User s manual Page 12 6 2 Output Menus Each output channel of the DCP 3060 has a separate menu key There are 6 menus for each output channel Signal Signal parameters e Refer to the Input Menus for details EQ EQ paramters e Refer to the Input Menus for details DCP 3060 User s manual Page 13 XOver Crossover parameters FTRL Filter Type of low frequency crossover point high pass Types can be Butterworth Linkritz Riley or Bessel O1 XXXXXX XOver FTRL Off FRQL Filter cut off Frequency of low frequency crossover point high pass
12. esolution Security Lock Lock Unlock Copy channels All parameters Channel Names 6 character length Note Specifications subject to change without notice DCP 3060 User s manual Page 23 10 0 Warranty The DCP 3060 is warranted covering materials and workmanship for a period of one 1 year as determined by the date of retail purchase according to the sales receipt from an authorized dealer or the date of manufacture if the sales receipt is not available according to the serial number This warranty applies to the product therefore the remainder of the warranty period will be automatically transferred to any subsequent owner This warranty applies only to failure of a Xilica product caused by defects in materials and workmanship during the stated warranty period It does not apply to a unit that has been subjected to abuse accident modification improper handling installation or repairs made without factory authorization or by anyone other than authorized Xilica Field Service Stations This warranty is void if the serial number has been defaced altered or removed Products covered by this warranty will be repaired or replaced at the option of Xilica without charge for materials or labor provided all the terms of this warranty have been met For factory service please call or email for a Return Authorization R A number before shipping If the product is shipped the following information must be included in the package 1
13. evel Type Audio Performance Frequency Response Dynamic Range CMMR Crosstalk Distortion gt 10k Ohms 50 Ohms 20dBu Electronically balanced 0 1dB 20 to 20kHz 115dB typ unweighted gt 60dB 50 to 10kHz lt 100dB 0 002 1kHz 4dBu Digital Audio Performance Processor Sampling Rate Analog Converters Propagation Delay Front Panel Controls Display Level Meters Buttons Dial Encoder Connectors Audio RS 232 Power General Power Dimensions Weight 32 bit 40 bit extended 48kHz High Performance 24 bit 3ms 2 x 16 Character Backlit LCD 5 segment LED 9 Mute Controls 9 Gain Menu Controls 6 Menu Controls Embedded Thumb Wheel 3 pin XLR Female DB 9 Standard IEC Socket 115 230 VAC 50 60Hz 19 x1 75 x8 483x44x203 mm 10lbs 4 6kg DCP 3060 User s manual Page 22 Audio Control Parameters Gain 40 to 15dB in 0 25dB steps Polarity Delay Up to 50ms per I O Equalizers 6 per I O Type Parametric Hi shelf Lo shelf Gain 30 to 15dB in 0 25dB steps Bandwidth 0 02 to 2 50 octaves Q 0 5 to 72 Crossover Filters 2 per Output Filter Types Butterworth Bessel Linkwitz Riley Slopes 6 to 48dB oct Limiters Threshold 20 to 20dBu Attack 0 3 to 100ms Release 2 to 32X the attack time System Parameters No of Programs 30 Program Names 12 character length Delay Units ms ft m Frequency Modes 36 steps oct 1Hz r
14. he unit from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning 7 DO NOT BLOCK ANY VENTILATION OPENINGS Slots and openings in the cabinet back or bottom are provided for ventilation to ensure reliable operation of the limit and to protect it from overheating These openings must not be blocked or covered The openings should never be blocked by placing the product on a bed sofa rug or similar surface This product should never be placed near or over a radiator or heat source This product should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacture s instructions have been adhered to DCP 3060 User s manual Page 2 8 DO NOT INSTALL NEAR ANY HEAT SOURCES This Product should be situated away from heat sources such as radiators stoves or other products including amplifiers that produces heat 9 DO NOT DEFEAT THE SAFETY PURPOSE OF THE POLARIZED OR GROUNDING TYPE PLUG A Polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prongs are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 PROTECT THE POWER CORD FROM BEING WALKED ON OR PINCHED PARTICULARLY AT PLUGS CONVENIENCE RECEPTACLES AND THE POINT WHERE TH
15. splays the DCP 3060 firmware version e After the initialization process is finished the DCP 3060 displays its main screen XILICA DCP 3060 e The screen shows the current program number and program name assigned to the unit The program assigned is always the last program the user recalled or stored before powering down the unit e Now the DCP 3060 is now ready to operate DCP 3060 User s manual Page 10 6 0 Operating the Device Tips Channel Linking If the user presses one of the Input or Output Menu keys holds it down and press any other Menu key s in the same group Input or Output group then the channels are linked together The green menu LEDs for the linked channels are lit Any modification of the data for the selected channel will be applied to the linked channels as well To cancel the linking just press any other Menu key or the Sys key after releasing the held key 6 1 Input menus Each of DCP 3060 input channels has a separate Menu key There are 3 menus for each input channel Signal Signal parameters e LEVEL Gain 40 00dB to 15 00dB in 0 25dB steps I1 XXXXXX Signal LEVEL 0 00dB e POL Polarity can be normal or inverted I1 XXXXXX Signal POL e DELAY Delay in 21us steps Can be displayed in ms ft or m The time unit of the delay can be changed in the System menu The maximum delay permitted is 2 400 steps 50ms I1 XXXXXX Signal DELAY 000 000ms DCP 3060 User s manual Pag
16. witz Riley Bessel Crossover High XOver FRQH 20 20 000 1 Hz Crossover High XOver SLPH 6 48 6 dB octave Out Limit Thresh Limit THRESH 20 20 0 5 dBu Out Attack Time Limit ATTACK 0 3 100 0 1 1 ms Out Release Time Limit RELEASE 2 4 8 16 32X Attack time Source Source 1 2 3 Off On Channel Name Ch Name NAME 6 characters DCP 3060 User s manual Page 20 The DCP 3060 is shipped with a special PC Graphic User Interface GUI application XLink XLink gives the user an option to control the DCP 3060 unit from a remote PC via the RS232 serial communication link The GUI application makes it much easier to control and monitor the device allowing the user to get the whole picture on one screen Programs can be recalled and stored from to PC s hard drive thus expanding the storage to become virtually limitless CT EZE A IO E 0 00 8 0 00 0 00 I 0 00 I 0 00 ij 0 00 0 00 y 0 00 ACTI ce ACI Mo mic ACTI ACTI ECT ACTI CTI IT MEIN MES IE EE Morra EII II EI II II O E IE J AA ta Do Do o e ink a E In2 In3 Out1 Out2 Out 3 Out 5 Out 6 Out 8 Progam Confio Copy Security ViwData AllPrograms Sync Device Home Link Status Enor DCP 3060 User s manual Page 21 9 0 Specifications Inputs and Outputs Input Impedance Output Impedance Maximum L
17. y 6 bands of parametric EQ per channel multiple crossover selections and full function limiters Precise frequency control is achieved with its 1 Hz resolution Inputs and outputs can be routed in multiple configuration to meet any requirements The DCP 3060 can be controlled or configured in real time on the front panel or with the intuitive PC GUI accessed via the RS 232 interface Software upgrade for CPU and DSP via PC keeps the device current with newly developed algorithms and functions once available Multiple setup storage and system security complete this professional package Shipped contents DCP 3060 unit User Manual XLink Software CD DCP 3060 User s manual Page 5 2 0 Features gt 3 Inputs and 6 Outputs with flexible routing gt 32 bit 40 bit extended floating point DSP gt High Performance 24 bit A D Converters gt 1 Hz Frequency Resolution gt 6 Parametric Equalizers for each Input and Output gt Multiple Crossover types with Full Function Limiters gt Precise Level Polarity and Delay gt CPU and DSP upgrade via PC gt Individual Channel Buttons with Linking capability gt 2 Line x 16 Character Backlit LCD Display gt Full 5 segment LED s on every Input and Output gt Storage of up to 30 Program Setups gt Security Lock gt RS 232 Interface for PC Control and Configuration gt Future options available DCP 3060 User s manual Page 6 3 0 Front Panel Functions 1 Mute keys
Download Pdf Manuals
Related Search