LIAISON Software
Contents
1. GRAFIK Eyee LIAISON LIGHTING CONTROL SOFTWARE Operating Instructions for GRAFIK Eyes LIAISON Software LIAISON Software lets you PROGRAM the following GRAFIK Eye Control Units Scenes intensities and fade times Load types includes non dim options Temporary Mode switch setting Control Unit communication assignments Temporary on line scenes Accessory Controls Control Unit communication assignments Power Panels Control Unit and Zone assign ment for each circuit Load types for each circuit Timeclock Events Real time and astronomic event scheduling Super Sequence Automated synchronized dynamic scene selection throughout the system INTERROGATE the system for The above information Number of Control Units and Accessory Controls present in system Control Unit type Number of Control Units zones 2 24 Accessory Control type BACK UP an entire programmed system including Timeclock events for archival purposes Requires the use of 3500 and or 4500 series Control Units and GRX PRG or GRX CI PRG For use with 3100 3500 4100 and or 4500 series Control Units Requires GRX PRG or GRX CI PRG a LUTRON GRAFIK Eye LIAISON LIGHTING CONTROL SOFTWARE reate or Edit a Project from File Installing GRAFIK Eye LIAISON System Requirements In order to use GRAFIK Eye LIAISON you will need the following HARDWARE IBMe compatible PC Penti2. View the Events for Today To view the events scheduled for the current day select EMHZ Re Es Today s Events from the Online Options menu The screen will display the current day what schedule is to run and the events In the specified schedule If any r events are astronomic the time the event will occur will be shown followed by an indicating that the time has es al been calculated based on sunrise or sunset g00AM SELECT SCENE 1 12 00PM SEQUENCE ON Click on Done to close Today s Events A Monitor the Super Sequence If a super sequence Creating or Editing a Project Y Online Super Sequence PE E3 from File has been created and transferred the cur rent status of your system can be viewed by selecting Online Super Sequence from the Online Options SELECT SCENE menu The Online Super Sequence screen will display SELECT SCENE 10 the status of the super sequence Additionally all steps of the sequence will be shown but cannot be edited From this screen the user can start resume and stop the loaded super sequence Selecting Start will begin the super sequence atthe fj 3 i g 3 e races first step If Start is selected while a super sequence Ee Done is running the Super sequence will immediately go to Emmmms 2 7 Step 1 and continue Selecting Start for a super sequence that is Paused see next page will contin ue the super sequence at the next step following the event when the super sequence was Paus
3. Conf Rm Entrance or Conf Rm Podium on the line corresponding to each Accessory Control Descriptions are for reference only and will not be downloaded to the Programmer Interface GRX PRG or GRX CI PRG 4 Indicate which Control Units you want each Accessory Control to talk to by checking each corresponding box For example click A1 on the first line of the Button table if you want the NTGRX 4S Accessory Control at Address 2 to talk to A1 5 For Fine Tuning Accessory Controls and Shade Accessory Controls individual zone control is available To program which zones of a Control Unit you want the Accessory to control click on the corresponding box This action will bring up a list box of zones for the selected Control Unit Select or de select zones by clicking on the zones of the list box or select de select all zones of the Control Unit by clicking the Select All Clear All button and then click Done to exit the screen SG 3WD is a dual 3 button shade control the top 3 buttons and the bottom 3 buttons can be programmed separately on a zone by zone basis 6 Once you have specified each Accessory Control and Controllers click Done to exit the screen LUTRON 6 Operating Instructions GRAFIK Eyee LIAISON Software Specify Controllers For Programmable Systems using GRX PRG or GRX CI PRG Only t s Uw From the Set Up menu select Specify Accessories Click the Controllers tab on the Accessory C
4. Editing Steps From the Edit menu use the Cut Copy Delete and Paste options to edit steps of the Super Sequence To edit a step select from the Step column and choose the appropriate edit function In addition an edit menu will appear by clicking the right mouse button when an event is highlighted This pop up menu also includes Insert Inserting a step will shift the highlighted step and all steps following down one step and paste the copied step to the current step If a step 60 has been defined it will be shifted off the list Click on Done to leave the Program Super Sequence screen Select Save in the File menu to save the defined Super Sequence After Hours Mode After Hours Mode of the GRX PRG or GRX CI PRG and LIAISON software allows the user to create timeclock schedules that minimize energy usage during off peak periods or periods of non occupancy After a user defined delay following the start of After Hours mode a user defined scene will be selected Any scene selection during this delay period will reset the delay period and lease the lighting for the space The user defined delay can range from two minutes to two hours After Hours mode can be cancelled via a scheduled event After Hours mode can be initiated and cancelled on any combination of Control Units The delay time is the same for all Control Units The scene to be selected is the same for all Control Units After Hours Scene A user designated scen
5. 5 6 7 8 anyday of the year used for special events or exceptions to the default In FERN ERS EN BENE wPUERNS wag addition schedules can be suspended or overridden oe eee ee E OE E ET j i eptember ctober ovember a using Calendar Suspending scheduled events on a a f eee a Sine e 2 ts Suspend ifi i Show Events specific day will only suspend the schedule for that day gys iEi dugdeell eullian e Any scheduled events will resume the following day rere H ia ae le Weekday Exceptions are saved by date in memory indefinitely Decenber 1558 Tal deruay 7583 Ta Februay 1883 Til Special 1 2 Te aoa g 7 8 ot eae B 14 15 16 17 18 13 20 0 Pal Pee rep PLY aay Fas ey 28 Done therefore annual maintenance may be needed for holidays that do not fall on the same day every year e g Thanksgiving Labor Day etc Fixed date holidays such as New Year s Day do not require maintenance 1 Select Calendar from the Timeclock menu tim April 1998 Bee aS awe 2 The Schedule Exceptions screen displays a one year calendar To add an exception drag a schedule from i j emn the list and drop it on any day of the year es es i eae Special 2 12 13 14 15 16 17 18 Suspend 3 To view the events in a schedule select the schedule s 2 a 2 2 4 2 ster Eves in the list and click Show Events s 9 a 8 m ae 4 To view an individual month the button in the top right corner of each month can be selected Using the month
6. CI PRG will also affect timeclock status However timeclock status cannot be enabled on any Control Unit if the timeclock has been turned off using DIP Switch 8 3 Click on Done to close the System Status screen liiis View the Details of your System The details of your system can be viewed in the System Details screen System details include Control Unit model number software revision ideal for troubleshooting communications information and temporary mode settings 1 Select System Details from the Online Options menu 2 lf any changes are made to the system click Update Details to refresh the list of Control Units This feature can be useful during installation or troubleshooting 3 Click on Done to close the System Details screen LUTRON 19 AN GRAFIK Eyee LIAISON Software Operating Instructions View the Accessory Control Details of your System The details of the Accessory Controls in your system can be viewed in the Accessory Control Details screen include Accessory Control model number function and communications information IMPORTANT Accessory Control details are only available from accessory controls with a minimum code revision To determine the code revision level inspect the back of the accessory control If you have questions please contact the Lutron Hotline for assistance Minimum Code Revision of Accessory Controls for Getting Details Type Minimum Code Revision Standard Accessory Con
7. Load Type 1 All 1 search for the next four addresses ELV each panel located circuit information will be received Neon Cold lf any changes are made to the system click Update Details to refresh the Control Unit and Zone and load type assignments This T NEW feature can be useful during installation or troubleshooting ae INC MLY g 4 Update Details Communicate with the GRX PRG or GRX CI PRG in Real Time Click on Done to close Online Power Panels All commands available through the user interface can also be sent using a terminal or equivalent device To use the terminal interface available with LIAISON Select Terminal from the Online Options menu _ Refer to the GRAFIK Eye RS232 Protocol help file installed in the LIAISON program group for commands that can be entered and data that can be received from this screen For a complete set of printed commands refer to the GRAFIK Eye RS232 Protocol Lutron P N 040 138 d Get System Location Information from the PRG m Select Location from the Online Options menu a LIAISON will display the project location information that was stored in the GRX PRG or GRX CI PRG m Click on Done to close online System Location form i System Location System Location User Defined Location Country State City l Select hom deraut locatione fu hited States Pa Philadelphia Location 4nd Time one Data Latit
8. default color of the LIAISON desktop by selecting a color from the palette The selection will be saved to an initialization file and used every time LIAISON is run Communications Type Specify how LIAISON will communicate with a PRG box GRX CI PRG supports RS232 and Ethernet communication LIAISON versions 4 0 and later support both RS232 and Ethernet communication The DevicelP button launches Lutron s Ethernet device discovery program installed from CD separately This program enables you to set and get the IP information from GRX CI PRG units that are connected over Ethernet and connected on the same Ethernet switch or hub or connected directly to the PC x Communications Port If serial communication is present transferring data to the GRAFIK Eye system requires the use of a PC serial COM port From the Preferences screen you may select the COM port through which data will be transferred The selection will be saved in an initialization file and will only need to be set the first time you use LIAISON to program your system or if you change the hardware configuration of your PC The COM port can also be selected from the Set COM Port of the Online Options menu Device IP Information If Ethernet communication is selected you must specify the IP address Port number and login of the GRX CI PRG box from the Preferences screen The following is the default setting of a GRX CI PRG IP Address 192 168 250 1 Port Number 23 lo
9. for Day By default weekday schedules will run Monday through Fal Default Schedule for Day Friday and weekend schedules will run Saturday and Sunday Weekend Weekday Special Special 2 No Schedule If your system requires modifications to this default week Sunday c s s z definition proceed as follows m lo change the week definition select Default Schedules Wednesday from the Timeclock menu The days that constitute week Touteis Friday days and weekend days can be modified in the Default Schedule for Day screen For example to run the weekend schedule every Monday select the Weekend button Saturday m When modifications have been completed click on Done to return to the main screen m Select Save from the File menu to save the changes 7 LUTRON 14 Operating Instructions GRAFIK Eyee LIAISON Software View and Modify Calendar Exceptions After creating and transferring a schedule of events the EEEN aes weekday and weekend schedules will run by default 12345 ees T ee every weekday and weekend as defined in the Default B38 1819 20 21 12 33 14 15 16 7 18 101 Eaters Schedule for Day screen see Default Schedule a ioa heir PES for Day Special 1 and Special 2 schedules can be SS SS a ieee 1 1 from the list below to a ei ff 1s A STETA a es wel eS a see e a 3 g ff Ue ee 2g e et ee TE ay as ee e e 0 UJ N t ot Q3 tom M 2ra A i E ee fe Cer a a es 9 10 11 2a
10. talk to by checking each corresponding box For example click the box under A1 if you want the controller to talk to A1 5 Once you have specified each Controller and Accessories click Done to exit the screen NOTES Each Controller in a system must be assigned a unique Controller address by setting the DIP switch es on the unit There are a maximum of 8 Controllers per system These Controllers do not occupy the 16 standard Accessory Control addresses GRX SVC GRX GC and GRX CCO Zone mode can only control zones on GRAFIK Eye Control Units with software revision 7 0 or higher these controllers will not function correctly with Control Units with lower software revisions Each GRX SVC unit each channel of a GRX GC each relay group of a GRX CCO Zone mode can talk to one zone in a system LUTRON 7 GRAFIK Eyee LIAISON Software Operating Instructions Program Control Units For Programmable Systems using GRX PRG or GRX CI PRG Only In addition to specifying Control Unit model numbers and communications scene names zone names scenes and load types are all programmable using LIAISON 1 Scenes are made up of zone intensities and fade times There are 16 scenes plus an Off scene for each Control Unit 2 Light intensities for all scenes except Off can be adjusted from O to 99 or unaffected UA AC shade positions for all scenes can be set to Open Close or unaffected UA Sivoia shade positions for all sc
11. value of intensity in the box below each zone For example for Scene 1 click on the Zone 1 Raise button to increase the light intensity of that zone or type in 90 in the box if gee you want the intensity at exactly 90 Repeat the procedure for each zone in the scene Lighting Zones Clicking on Raise Lower button or typing in intensity value to set lights intensity AC Shade Zones Clicking on Raise Lower button or typing in the following key to set shade position Open and Close Or Typing in O or o for Open Typing in C or c for Close LUTRON 8 Operating Instructions GRAFIK Eyee LIAISON Software Sivoia Shade Zones Clicking on Raise Lower button or typing in the following key to set shade position Open Preset 1 Preset 2 Preset 3 and Close Or Typing in O or o for Open Typing in C or c for Close Typing in 1 for Preset 1 Typing in 2 for Preset 2 Typing in 3 for Preset 3 Fade Time m Modify the Fade Time for the scene by clicking on the Raise Lower buttons in the Fade box OR by typing in the exact value in the Fade window m Follow the same procedure for each scene aa Program Control Unite m Fade time will not be applied to non lighting zones Select Load Types m O select Load Types click on the Load Types button in the Program Control Units window m Click on the Raise Lower buttons of each zone until the correct nu
12. will be for all buttons or each individual button IMPORTANT Accessory Control details are only available from accessory controls with a minimum code revision To determine the code revision level inspect the back of the accessory control If you have questions please contact the Lutron Hotline for assistance Minimum Code Revision of Accessory Controls For Getting Details Type Minimum Code Revision Standard Accessory Control 2 0 Shade Accessory Control 1 1 Accessories Click the Accessories tab on the Accessory Controls in this System form Click on the drop down menu under the Model column and select the Accessory Control model BRK 26 Finetune ADDRESS numbers for your system weds a None Address 4 2 The functions listed for each address are dependent on the model selected in the first NTGRX 4S Scene Selection Control res column Click on the drop down menu under 5 Scene selection iise lower and off on ons or more cach Accesuy the Function column and select the function for Button at a2 a3 A4 A5 AG A7 AS to the Accessory Control The button table at the A 2k DEN ee Done bottom of the screen may change from ALL to individual buttons based on the selected function NOTE The bottom of this screen may have a different appearance for certain Accessory Controls 3 Name your Accessory Control by highlighting the Description section and entering a description such as
13. your office for future downloading to a GRAFIK Eye system Go Online with System Select this mode after you have transferred data using Create or Edit a Project from File to monitor and operate your GRAFIK Eye system This mode requires interfacing with the GRX PRG or GRX CI PRG refer to instruction sheet P N 040 135 or 040 228 See Page 18 CREATE OR EDIT A PROJECT FROM FILE FILE MENU Open m f you have already created a job file open that file using Open LIAISON files have the extension lia and by default are saved in the same directory as LIAISON New m From the File menu select New Select the type of system that you will be designing There are three options when creating a new file s aw 1 Timeclock Only Schedule real time and or astronomic events for the entire system Use the super sequence for dynamic synchronized scene selections throughout the system Requires a GRX PRG or GRX CI PRG and 3100 and or 4100 series Control Units Programmable System Includes all the Timeclock Only features plus the ability to program all aspects of the system operation using LIAISON Program all Control Unit information scenes intensities and fade times load tyoes communication assignments and temporary mode options m Program Control Unit and zone assignments to the circuits in the system m Program the Control Unit communication assignments for Accessory Controls m Also program all the Timeclock eve
14. Made and printed in U S A 03 07 P N 040 139 Rev E 7 s lt LUTRON
15. S BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR FOR ANY CLAIM BY ANY OTHER PARTY YOU HAVE THE SOLE RESPONSIBILITY FOR ENSURING ADEQUATE PROTECTION AND BACKUP OF YOUR DATA USED IN CONNECTION WITH THE SOFTWARE AS WELL AS ENSURING ADEQUATE PROTECTION OF THE SOFTWARE AND YOUR SERVERS INCLUDING WITHOUT LIMITATION SECURING YOUR SERVERS WITH APPROPRIATE PASSWORDS FIREWALLS AND OTHER RESTRICTIONS ON WHO CAN ACCESS THE SERVERS THE SOFTWARE AND THE DATA LIMITATION OF LIABILITY AND REMEDIES NOTWITHSTANDING ANY DAMAGES THAT YOU MIGHT INCUR FOR ANY REASON WHATSOEVER INCLUDING WITHOUT LIMITATION ALL DAMAGES REFERRED TO ABOVE AND ALL DIRECT OR GENERAL DAMAGES THE ENTIRE LIABILITY OF LUTRON AND ANY OF ITS SUPPLIERS UNDER ANY PROVISION OF THIS LICENSE AGREEMENT AND YOUR EXCLUSIVE REMEDY FOR ALL OF THE FOREGOING SHALL BE LIMITED TO THE AMOUNT ACTUALLY PAID BY YOU FOR THIS SOFTWARE OR U S 100 00 AT LUTRON S SOLE DISCRETION THE FOREGOING LIMITATIONS EXCLUSIONS AND DISCLAIMERS SHALL APPLY TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW EVEN IF ANY REMEDY FAILS OF ITS ESSENTIAL PURPOSE SOME STATES OR JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU THE WARRANTY CONTAINED IN THIS LICENSE AGREEMENT GIVES YOU SPECIFIC RIGHTS YOU MAY HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR JURISDICTION TO JURISDICTION Lutron and GRAFIK Eye are register
16. WARRANTIES DUTIES OR CONDITIONS OF MERCHANTABILITY OF FITNESS FOR A PARTICULAR PURPOSE OF ACCURACY OR COMPLETENESS OF RESPONSES OF RESULTS OF WORKMANLIKE EFFORT OF LACK OF VIRUSES AND OF LACK OF NEGLIGENCE ALL WITH REGARD TO THE SOFTWARE AND THE PROVISION OF OR FAILURE TO PROVIDE SUPPORT SERVICES ALSO THERE IS NO WARRANTY OR CONDITION OF TITLE QUIET ENJOYMENT QUIET POSSESSION CORRESPONDENCE TO DESCRIPTION OR NON INFRINGEMENT WITH REGARD TO THE SOFTWARE EXCLUSION OF INCIDENTAL CONSEQUENTIAL AND CERTAIN OTHER DAMAGES TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW IN NO EVENT WILL LUTRON OR ITS SUPPLIERS BE LIABLE TO YOU FOR ANY SPECIAL INCIDENTAL INDIRECT OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO DAMAGES FOR LOST PROFITS LOSS OF DATA LOSS OF CONFIDENTIAL OR OTHER INFORMATION BUSINESS INTERRUPTION PERSONAL INJURY LOSS OF PRIVACY LOST SAVINGS FAILURE TO MEET ANY DUTY INCLUDING OF GOOD FAITH OR OF REASONABLE CARE FOR NEGLIGENCE AND FOR ANY OTHER PECUNIARY OR OTHER LOSS WHATSOEVER ARISING OUT OF YOUR USE OR INABILITY TO USE THE SOFTWARE THE PROVISION OF OR FAILURE TO PROVIDE SUPPORT SERVICES OR OTHERWISE UNDER OR IN CONNECTION WITH ANY PROVISION OF THIS LICENSE AGREEMENT EVEN IN THE EVENT OF THE FAULT TORT INCLUDING NEGLIGENCE STRICT LIABILITY BREACH OF CONTRACT OR BREACH OF WARRANTY OF LUTRON OR ANY SUPPLIER AND EVEN IF LUTRON OR AN AUTHORIZED LUTRON REPRESENTATIVE OF LUTRON OR ANY SUPPLIER HA
17. e already been programmed you will have to confirm the deletion when prompted 4 window Shades AC Motor The load schedule table at the bottom of the screen lists the circuits in the panel and allows the user to program the Control Unit zone assignments and the load type for each circuit In addition cus tomer circuit information can be provided for reference Select Customer Circuit or Customer Circuit Name to enter customer specific information Click on the Control Unit cell and select from the pull down list the Control Unit of the Zone that will be dimmed by this circuit Only those Control Units that have been included in the system see Specify Control Units will be listed After selecting the Control Unit click on the Zone cell and select a zone from the list This is the zone that will control the light level of the loads attached to the circuit Finally click on the Load Type cell and select from the pull down list the load type of the fixtures of the circuit The load type must be specified at the power panel in addition to specifying load type on the Control Unit see Program Control Units Program the remaining circuits of the panel in the same manner To add additional panels to the sys tem click Add New Panel A new panel will be added to the bottom of the panel table Once you have programmed all the Power Panels click Done to exit the screen Remember to save your changes while working b
18. e and Timeclock Events GRAFIK Eye Accessory Controls NTGRX 2B SL and GRX AV can be assigned to manually control the Timeclock interface by providing the following functions start pause and resume a Super Sequence and turn on or off Timeclock events m lo assign an Accessory Control select Wallstation Control Walstation Controls from the Timeclock menu Choose the appropriate system i e ee sek pee we address for the Accessory Control and the Wallstation type fj 200000 2 sses NTGRX 2B SL or GRX AV a NOTE The Accessory Controls must have the function DIP Switches set for Scene 1 selection START None z PAUSE moo m Assign a button for the function required RESUME E 7 m Select Save from the File menu to save the changes zs LUTRON 17 s aw GRAFIK Eyee LIAISON Software Operating Instructions ONLINE OPTIONS MENU Communicating with the GRX PRG or GRX CI PRG Interface Control Establish communication with the Interface Control Review the GRX PRG or GRX CI PRG instruction sheet before attempting to communicate with the Interface Control For serial connection verify that the provided cable is connected on the Interface Control to a COM port on your computer For Ethernet connection verify that the PC and the GRX CI PRG are connected via an Ethernet network NOTE At this time it is assumed that all system wiring has been completed correctly For Serial connection select Set COM Port from the Onli
19. e that is automatically selected after a user defined delay following a scene selection during After Hours Mode While in After Hours mode the system can automatically return to the desired energy efficiency level during periods of non occupancy or off peak usage After Hours Timeout A user defined time period between two minutes and two hours that the system will stay in a selected scene during After Hours Mode When the time expires the system will automatically select the After Hours Scene LUTRON 16 Operating Instructions GRAFIK Eyee LIAISON Software m Configure After Hours Mode 1 In Edit Mode from the Timeclock menu select After Hours Mode 2 On the After Hours Mode screen check Enable After Hours Mode to enable the After Hours Mode or uncheck the box to disabled it 3 Specify the After Hours Timeout The valid timeout range is 2 minutes to 2 hours Default timeout is 2 hours 4 Select an After Hours Scene After Hours Mode Scene can be any Scene from Scene 1 to16 or scene Off the default is Scene 15 5 Click Done to exit the After Hours Mode screen m After Hours Mode events start After Hours Mode Cancel After Hours Mode These events can be scheduled as timeclock events a View System After Hours Mode Configuration In online mode from Online Options menu select After Hours Mode NOTE After Hours Mode requires a GRX PRG with minimum code revision of 4 2 or GRX CI PRG Assign Controls for Super Sequenc
20. ed Selecting Pause will halt the super sequence at the current step This function may be ideal in a showroom application where specific areas are illuminated in a sequential manner and then stepped through to highlight specific areas Selecting Stop will halt the super sequence Any Start command or Resume from a Wallstation Control Creating or Editing a Project from File will begin the super sequence at the first step Any status change to the super sequence made by a Wallstation Control will affect the status viewed in Online Super Sequence Click on Done to close Online Super Sequence AV mw GRAFIK Eyee LIAISON Software Operating Instructions View the Power Panels of your System The details of the power panels in your system can be viewed in the Online Power Panels screen Panel details include Control Unit and zone assignment and load type for each circuit of a panel IMPORTANT Power Panel details are only available from circuit selectors with a code revision level of 2 50 or newer The code revision is available on the circuit selector of the panel If you have questions please contact the Lutron Hotline for assistance Select Online Power Panels from the Online Options menu f Online Power Panels Tex Address CodeRev Rev Select the panel ikea load LIAISON will search for the first four addresses of power panels For BPrS383 Sige 1 To check for more panel addresses click More Panels LIAISON will
21. ed trademarks and LIAISON is a trademark of Lutron Electronics Co Inc IBM is a registered trademark of International Business Machines Corporation Windows and Microsoft are registered trademarks of Microsoft Corporation Pentium is a registered trademark of Intel Corporation 1998 2001 Lutron Electronics Co Inc Internet www lutron com E mail product lutron com WORLD HEADQUARTERS Lutron Electronics Co Inc TOLL FREE 800 523 9466 U S A Canada Caribbean Tel 610 282 3800 International 1 610 282 3800 Fax 610 282 1243 International 1 610 282 1243 GREAT BRITAIN Lutron EA Ltd Tel 171 702 0657 International 44 0 207 702 0657 Fax 171 480 6899 International 44 0 207 480 6899 GERMANY Lutron Electronics GmbH Tel 809 710 4590 International 49 30 97 10 4590 Fax 309 710 4591 International 49 30 97 10 4591 FRANCE Lutron LTC International 33 0 1 44 70 71 86 Intl Fax 38 0 1 44 70 70 97 ASIAN HEADQUARTERS Lutron Asuka Corporation Japan Tel 03 5405 7383 International 81 3 5405 7333 Fax 03 5405 7496 International 81 3 5405 7496 HONG KONG SALES OFFICE Lutron GL Hong Kong Tel 2104 7733 International 852 2104 7733 Fax 2104 633 International 852 2104 7633 SINGAPORE Lutron GL Singapore Tel 65 220 4666 Fax 4 65 220 4333 Lutron Technical Support Hotline 24 hrs 1 800 523 9466 Lutron Electronics Co Inc
22. elect the information to be printed and then click OK Exit m To exit LIAISON select Exit from the File menu If changes have been made to the currently opened file or a new file was created that has not been saved a prompt to save will be issued before exiting VIEW MENU Enter Project Information By default the Project Information screen is shown every time a new file is created This information can be viewed or edited at any time From the View menu select Project Information m For future reference enter the job name location and descrip tion in the corresponding boxes m Enter the name of individuals and companies for whom the system was designed Include addresses for future reference m Click Done to exit the screen Design By Design For i Name Nancy C tom Company us ddr Coopersburg z 4 Set Preferences Customize LIAISON by setting preferences for the user and hardware interface Preferences for toolbar views desktop color and communication settings are set by selecting Preferences from the View menu m Toolbar The toolbar below can be displayed by selecting Buttons Without Text from the Preferences screen Also Large Buttons With Text and No Buttons are options in the Preferences screen The toolbar provides a shortcut means of selecting menu items teme ae oes ele LUTRON 3 GRAFIK Eyeo LIAISON Software Operating Instructions Desktop Color Change the
23. enes can be set to Open Preset 1 Preset 2 Preset 3 Close or unaffected UA The light level or shade position of an unaffected zone will not change when that scene is selected 3 Fade times are adjustable for all scenes and can range from O to 59 seconds or 1 to 60 minutes The fade time is the time it will take for the zone intensities to raise or lower to the scene s preset level from their current intensities 4 Load types are the type of fixture s that will be controlled on a zone by zone basis It is important to specify the correct load type for each zone to achieve the best dimming performance m From the Set Up menu select Program Control Units Click on the list box in the upper left hand corner of the window and choose from the units specified previously For example click on Confer ence Room to program the Conference Room Control Unit Zone Names m Click on the Zones button a to label your zones Enter the names of your zones e g Downlights or Sconces in the Zones text boxes Presets Fade window Master Raise Lower buttons m Click on the Presets button to set up your scenes Select the scene you want to create In the Scenes list box To change the name of the scene highlight the Scenes list box and enter zone the new scene name lower To create a scene set the intensities of the Fields zones in that scene by clicking on the Zone entering Raise and Lower buttons of each zone OR by typing in the
24. entering a description such as Conference L211 Haze Room or Lobby on the line corresponding to each Control Unit 3 If the Control Units are 3500 and 4500 series check off the addresses of all the Control Units you want each Control Unit to talk to by clicking each corresponding box For example click A2 on the first line if you want Control Unit A1 to talk to Control Unit A2 4 Once you have specified each Control Unit click Done to exit the screen If Timeclock Only was specified when the file was created OR the Wizard decisions did not require programmable Control Units skip the rest of this Section and proceed to Timeclock Menu on Page 13 LUTRON 5 s Uw GRAFIK Eyee LIAISON Software Operating Instructions Specify Accessories For Programmable Systems using GRX PRG or GRX CI PRG Only Many GRAFIK Eye systems include Accessory Controls that allow for remote control of Control Unit s These accessories must be told which Control Unit s to talk to Some accessories are pro grammed such that all buttons talk to the same Control Unit s Others such as partition controls are programmed on a button by button basis These differences are based upon Accessory model and functionality For this reason Accessory Controls must be specified and then programmed NOTE Model information and functionality will not be programmed This information is used to deter mine whether programming
25. ependent on the options chosen in the Transfer Options screen After the data has been compiled and transferred the message will read System Compiled Successfully After transferring data you will be prompted to switch to Online Mode If you would like to monitor the currently installed system switch to Online Mode otherwise if additional editing to the system file is required remain in the Edit Mode Congratulations You have completed programming using LIAISON Lighting Control Software for GRAFIK Eye To monitor the status of your system continue to the next section Go Online with System GO ONLINE WITH SYSTEM After you have transferred data using the first mode Create or Edit a Project from File select this mode to monitor and operate your GRAFIK Eye system System status is available for each Control Unit in the system System status includes current scene selected Timeclock status Super Sequence status and scheduled events Monitoring an installed project does not require a database file files with extension lia The only system information that will not be available will be panel names All other information can be monitored and or retrieved from any installed system LUTRON 18 s aw Operating Instructions GRAFIK Eyee LIAISON Software EHLE Set the Time and Date in the GRX PRG or GRX CI PRG SET TIME AND DATE 1 Select Set Time and Date from the Online Options em ct Mr Curent Date in S232 Interface Contr
26. gin nwk Advanced m Set redirection connecting time By default port redirection connecting time is O If a longer connecting time is needed i e the user tries to use LIAISON to control a GRAFIK Eye system via a network by network enabling the serial device or via telnet to a remote location the user can click Advanced button and specify the connecting time via the Connection and Communication Time screen This time is used when establishing communication Set response timeout By default the response timeout is set to 0 5 second During communication LIAISON will wait for a response from the PRG after sending out a command LIAISON will stop waiting if it receives a response or times out m Log communications If this option is checked the communication between LIAISON software and the PRG will be logged to a file Note that this option may slow down the communication process and should be used for troubleshooting only By default the communication will not be logged If you want to log communication reselect this option each time you start LIAISON The log file is named LiaCommunication log and is located in the LIAISON application directory New records are appended to the log file If you need a clean log file you can delete or rename the existing log file and the software will create a new log file for you NOTE LIAISON is designed to communicate with the GRX PRG GRX CI PRG or GRX RS232 via serial communication or Ether
27. in the appropriate locations on the screen Latitude and longitude are in units of degrees For example 12 5 12 degrees 30 minutes Now enter the correct time zone and Daylight Savings information 4 Click on Done to return to the start up screen Select Save from the File menu to save the changes SETUP MENU Specify Control Units NOTE Programming directly from a Control Unit requires 3500 and 4500 series Control Units Control Units are specified based upon the type of system that you are designing If Timeclock Only was specified when the file was created OR the Wizard decisions did not require programmable Control Units models will be limited to 3100 and 4100 series Control Units If Programmable System was specified OR the Wizard decisions included creating scenes for GRAFIK Eye Control Units the model list will include 3500 and 4500 series Control Units 1 From the Set Up menu select Specify tan Control Units in this System Bis Control Units Click on the menu Under Select the GRAFIK Eye models for your Check the addresses of all units you want system Name your control units each control unit to talk to the Model column to select or change the ee LA2 TAs ae fas Tas Tar Tas Conference Room GRX 3504 GRAFIK Eye model numbers for your sys GRx 3503 VE Lobby tem NotUsed SMM UNIT 3 Not Used UNIT 4 2 Use your pointer to highlight the Description suse unre section and name your Control Units by Not Used a
28. ion To retrieve the current system configuration Once communication has been established between the PC and the Interface Control select Decompile from the Online Options menu The LIAISON Decompiler screen will contain messages pertaining to the current status of the retrieval The first step of decompiling is to select a file name for saving the configuration A warning will appear if the file already exists After retrieving the data you will be prompted to switch to Edit Mode If you would like to view or edit the currently installed sys tem switch to Edit Mode where the decompiled file will be open otherwise if additional monitoring to the system file is desired remain in the Online Mode Finally Switching between Edit Mode and Online Mode After starting LIAISON it is still possible to switch between Create or Edit a Project from File and Go Online with System modes From either mode select the File menu Depending on the current mode of operation select either Go to Online Mode or Go to Edit Mode LUTRON 23 TERMS AND CONDITIONS The Grafik Eye LIAISON software is provided AS IS Lutron makes no claims warranties or promises as to its performance This software is provided without charge DISCLAIMER OF WARRANTIES EXCEPT FOR THE FOREGOING EXPRESS WARRANTY LUTRON HEREBY DISCLAIMS ALL OTHER WARRANTIES AND CONDITIONS EITHER EXPRESS IMPLIED OR STATUTORY INCLUDING BUT NOT LIMITED TO ANY IF ANY IMPLIED
29. it To adjust the current light levels or make gt E TE modifications to presets select Online a see isons iets Soa te pair amore tps Scenes from the Online Options menu Zon refle atte ete the ai stio rthe Any modifications to the light levels using Online Scenes will make TEMPORARY SCENE the currently selected scene on the Control Unit This protects you from inadvertently changing presets unless you are sure of the modifications To save a temporary preset use the Save Options to select the scene and then press Save swLUTRON 20 zs LUTRON 21 s Operating Instructions GRAFIK Eyeo LIAISON Software NOTE All preset and system information in online mode is real time and does not require a file to be opened Saving a preset in this screen saves the data to the Control Unit in the system To retrieve and save this information to a file refer to Decompile To change the Control Unit being viewed select from the Unit Currently Being Monitored list The list of Control Units are the names last programmed using LIAISON To change the current scene of the Control Unit being viewed select from the Scene Currently Selected list Remember the zone intensities shown reflect the current intensities in the space They may not be the preset for the current scene if someone has adjusted light levels from an Accessory Control or directly at the Control Unit Click on Done to close the Online Scenes screen
30. lease contact the Lutron Hotline for assistance IMPORTANT Power Panel details are only available from circuit selectors with a code revision level of 2 50 or newer The code revision is available on the circuit selector of the panel If you have questions please contact the Lutron Hotline for assistance From the Set Up menu select Program Power Dimmer Panel Assignment EO Bex core e umber elect the panel to program loa Panels Choose the Panel to program by specify eed ee ircui schedules ing the address in the table at the top of the screen 2 Add Non Pare For example click on Address 1 to program the Conference Room GP4 Ow Trac 2 ve Blu Neon Cold Cathode To modify the name of the panel select the Name 3 SEW cell of the panel address you are modifying Enter in the new panel name This name is for reference only and will not be downloaded to the system To change how the load schedule is ordered click on a column header To modify the number of circuits in a panel select Sorted by Lutron Circuit Done the Number of Circuits cell of the panel address you are modifying Use the pull down list box to select the number of circuits for the panel being pro grammed If the new number of circuits is greater than the original number the circuits will be added to the current load schedule If the new number is less than the original number the circuits will be deleted If any circuits to be deleted hav
31. mber of LEDs corresponding to the appropriate load type as defined in the chart at the bottom of the screen are lit For example for elec tronic low voltage loads use the Raise Lower buttons to light two LEDs Repeat for each zone Load Type Legend LED Display Load Type Description GRX 3xxx Integrale GXI 3xxx GRX units Yes Incandescent Magnetic low voltage HP 2 4 6 loads 120v supply only Integrale Magnatic Low Voltage MLV GRX units Electronic low voltage Lutron Hi lume or Eco 10 fluorescent Integrale GRX TVI Tu wire compact fluorescent rev 5 5 or higher LUTRON 9 GRAFIK Eyeo LIAISON Software Operating Instructions Neon Cold cathode Non dim last on first off Non dim first on first off AC shade rev 7 0 or rev 7 0 or higher higher Sivoia shade rev 7 0 or rev 7 0 or higher higher Unassigned Non Dim This setting is the default for GXI Control units Auto Phase Last LED ON Reverse Trailing edge Last LED OFF Forward Leading edge Note LIAISON will always display Reverse Trailing edge s LUTRON 10 Operating Instructions GRAFIK Eyeo LIAISON Software Electronic Low Voltage ELV Incandescent GRX ELVI O 10v ballasts DSI compatible ballasts DALI intensity broadcast only ballasts PWM ballasts Key Yes All versions support the LoadType Rev All versions of that code rev
32. ne Options menu or Preference form Select the COM port that corresponds to the port on your computer to which the GRX PRG or GRX CI PRG is connected For Ethernet connection specify IP address Port number and login of the GRX CI PRG from the Preference form Click the Advance button on the Preference form to open the Connection or Communication Time form Specify Connection Timeout and Response Timeout from this form Select Establish Communication from the Online Options menu LIAISON will attempt to locate a GRX PRG or GRX CI PRG Interface Control If one exists and is connected properly you will be notified that the unit was found If an error message is displayed check the wiring to the Interface Control and the PC Transfer Data to the GRX PRG or GRX CI PRG Interface Control Once communication has been established between the PC and the Interface Control select Trans fer Data from the Online Options menu The Transfer Options screen allows the user to selectively transfer portions of data to the system This feature is useful when only a portion e g Timeclock events of the system information has been modified An initial transfer of any system requires that all system information be programmed and will take longer than selectively transferring data After selecting OK the GRAFIK Eye LIAISON Compiler screen will contain messages pertaining to the current status of the transfer The messages shown during compilation will be d
33. net If the user decides to network enable the serial device the communication quality and port redirection connecting time may vary depending on the system setup i e the network adapter device server redirector software operating system etc Not all port redirector software and device servers will work with LIAISON It is the user s responsibility to test the communication s LUTRON 4 Operating Instructions GRAFIK Eyee LIAISON Software E Enter Geographical Location System Location mE System Location A User Defined Location Country State City i i i i Select from default locations nited States v T iladelphia v The geographical location of a job must be defined tmetibates fissa x Pi zA Prieta if any astronomic events are to be scheduled Latitude 51 Longitude 51w TimeZone E Daylight Savings Time Data 1 Select the Location item found in the View Daylight Savings Correction Amount menu Starting Month Amio Ending Month Starting Day OF Week v Ending Day Of Week 2 Select the city where the job is located using the statingoayormonh P Ending Day Of Month pull down lists for Country State if applicable Starting Time 20am Ending Time and City The location value time zone and daylight savings information associated with the chosen city will appear on the screen 3 If the desired city is not present in the list select User Defined Location and enter the latitude and longitude
34. nt type ee EM Lobby will be listed in the schedule ee Add New Time 3 00 PM NOTE For both event types the time 4 00 PM resolution is to the nearest minute Figure 1 displays Time of Day events Figure 1 Time of Day Events All four schedules can include both real time and astronomic events though they cannot be viewed simultaneously on the Schedule Events screen 3 Add an event The Schedule Events screen utilizes the drag and drop method of adding items to alist To add an event begin by adding an action to the list of events Select an action in the Actions list Click on this item by pressing and holding the left button of your mouse Continue to hold the left button down and drag the action to a time in the Time of Day or Astronomic event list To drop the action release the mouse button when the time for the event is highlighted Actions can be dropped on times or other actions For example to change the action of a previously defined event you would drag and drop the new action onto the original action After adding an action you must specify at which GRAFIK Eye Control Units the action will occur The only actions that do not require a Control Unit are SUPER SEQUENCE ON or OFF To add a Control Unit or Units to an action click on the Control Unit in the Control Units list Press and hold the left button of your mouse and drop the Control Unit to an action in the list Control Units can be dro
35. nts and super sequence events available with Timeclock Only Note Programming Requires a GRX PRG or GRX CI PRG To program directly from a Control Unit a 8500 and or 4500 series Control Unit is necessary Lutron Lighting Wizard If you are still in the process of designing your system let the Lutron Lighting Wizard assist you in creating a New file After answering the questions presented by the Wizard and LUTRON 2 Operating Instructions GRAFIK Eyee LIAISON Software clicking Finish those screens that apply to your project will be shown If you want to add to or edit your system at a later time simply use the menus to reopen the needed screen The equipment required is based upon choices selected using the Wizard m From the File menu select Save to save the file Import GRAFIK Eye Timeclock GTC m GRAFIK Eye LIAISON can also be used to create Timeclock Only systems Timeclock systems that have been created by GRAFIK Eye Timeclock P N GRXTC WIN can be imported to LIAISON From the File menu select Import gt GRAFIK Eye Timeclock GTC After selecting the file to import click on OK The file extension will be changed from gtc to lia and the imported file will be opened for editing The original file created by GRAFIK Eye Timeclock will not be changed Print m From the File menu select Print to print information about the currently opened file All system infor mation or selected information can be printed S
36. ol mene Friday August 22 1097 i Synchronize the A5232 clock b 2 The current time and date in the Interface Control will be a p Dome i i Synchronize displayed If the time or date needs to be modified type in the correct information and click the Synchronize button Do not include the day of the week when entering the date 3 Click on Done after the time and date have been set Check the Status of your System 1 The current status of your system can be viewed by BERSSOREs selecting System Status from the Online Options i System Details Online Scenes e 1 i ress ontro ni Iimecioc Vents cene atus information such as the currently selected scene at r Conference Room Disabled Enabled Scene 2 each Control Unit With LIAISON Timeclock events 2 Lobby ODisabled Enabled Scene 13 can be enabled and disabled on a Control Unit by Control Unit basis By disabling the timeclock for a specific Control Unit timeclock events will still occur but will not affect the specified Control Unit 2 If a wallstation control has been configured to turn Timeclock Events on and off Create or Edit a f Project from File the Timeclock Status shown in the m o ON AS ON aa UA 5 25 38 pe System Status screen will be affected The Timeclock ON and OFF functions will enable and disable respectively the timeclock events of all Control Units in the system In addition DIP Switch 8 Timeclock ON OFF on the GRX PRG or GRX
37. ontrols in this System form Click on the drop down menu under the Model column and select the Controller model numbers for your system The functions listed for each address are dependent on the model selected in the first column Click on the drop down menu under the Function column and select the function for the Accessory Control Name your Controller by highlighting the Description section and entering a description such as Conf Rm Entrance or Conf Rm Podium on the line corresponding to each Controller Descriptions are for reference only and will not be downloaded to the Programmer Interface GRX PRG or GRX CI PRG NOTE The bottom of this screen may have a different appearance for certain Accessory Controls Using the table at the bottom of the screen to program the selected controller GRX SVC Specify a zone to control GRX GC For each channel of the unit specify a zone to control GRX CCO Zone mode For each relay group of the unit specify a zone to control Click on the drop down menu under the Control Unit column of the bottom table select the Control Unit that you want the selected unit channel relay group to talk to from the list Click on the drop down menu under the Zone column of the bottom table select the zone that you want the selected unit channel relay group to talk to from the list GRX CCO Scene mode Indicate which Control Units you want the controller to
38. or higher GRX 4000 units should be set to Load Type 1 for those Load Types Temporary Mode m 0O set the Temporary Mode click on the Temporary Mode button A m Use the Master Raise Lower buttons to select a Temporary Mode Sd to Save by default Sb to Save by button Sn to Save never 4S for Scene selection and Master Raise Lower only and bd for Buttons disabled The Temporary Mode selected appears in the Fade window Press F1 for descrip tions s LUTRON 14 s aw GRAFIK Eyee LIAISON Software Operating Instructions Program Power Panels For Programmable Systems using GRX PRG or GRX CI PRG Only If your system requires the use of GRAFIK Eye dimming or switching panels use LIAISON to program Control Unit and Zone assignments plus the load type for each circuit It will be necessary to Program Power Panels if 4100 or 4500 series Control Units have been included in the system Each circuit of a dimming panel receives its light level from a Control Unit and Zone in the system Each circuit will have an individual Zone assigned however multiple circuits may have the same Zone assignment Load types are the type of fixture s that will be controlled on a zone by zone basis It is important to specify the correct load type for each zone to achieve the best dimming performance NOTE Power Panels must be uniquely addressed to allow for programming If you have any questions regarding panel addressing circuit capacities or load types p
39. pped on actions or other Control Units If the Control Unit is already included in the action it will not be added a second time Multiple Control Units can be listed under an action by dragging additional items from the Control Units list to an action in the event list NOTE Only those Control Units that have been included in Specify Control Units will be available for selection NOTE To schedule a START AFTER HOURS MODE or CANCEL AFTER HOURS MODE event After Hours Mode must be enabled 4 Change an event time To change the time that an event will occur again use the drag and drop method Click on the action in the event list Press and hold the left button of your mouse 7 LUTRON 13 GRAFIK Eyee LIAISON Software Operating Instructions Create a Timeclock Schedule continuation Drag this action to the new time in the event list If the time is not listed follow the procedures below to add the new time and then relocate the action 5 Add New Time If you wish to schedule an event for a time not included on the list you will need to add the time In the Enter New Time text box type the time of the event For Time of Day events type in the time formatted based on the computer s international settings For Astronomic events type in the desired amount of time Before or After sunRise or SunSet up to 2 hours fol lowed by the appropriate code BS AS BR AR After entering the time click on Add Ne
40. the step Occurs Set a Hold Time The Hold Time defines the amount of time the system will wait before executing the next Super Sequence step The range of hold times are O to 60 seconds and O to 99 minutes If a Hold Time of O seconds is used that step and the next step will occur simultaneously Operating Instructions l Program Super Sequence Program your super sequence by selecting the scene for the step Then click the control units at which the scene will be selected Hold Time is the time after the scene is selected until the next step Use the radio buttons to set whether the super sequence will run once and stop or run continuously Step Scene to Select a1 a2 a3 aa a5 as a7 As Hold Time No Step End No Step End No Step End LLLLLEABRLEAL EN EN E N EN E a e EN EN ah E E et S SN SN EN a TEN SN N ESU Sy EN E seh eal a TSN IEN SN EN EN E N N els E a E EN EN E SA Ey EN EN SE EN EN EN EQ EN E EN Ti Run Sequence and Loop C Run Sequence Once and Stop NOTE The hold time begins as soon as the scene is selected not after the scene has completed its fade If your application requires that a scene remains for a given time after it has completed its fade you must add the scene s fade time to the hold time For example you require that Scene 1 remains for 20 seconds after it has completed its fade Scene 1 has a fade of 5 seconds therefore a Hold Time of 25 seconds should be set
41. trol 2 0 Shade Accessory Control 1A 1 Select Accessory Controls Details from the Online Options menu fF Accessory Control Details Click the Accessories tab on the Accessory Control TN Details screen to view Accessory details Address Model Funcion Not Used Click the Controllers tab on the Accessory Control lotUsed Details screen to view Controller details Not Used Not Used Controllers GRx 4M GC Group Controller 2 The function is derived from the DIP switch settings of the Accessory Control Refer to the installation and instruction sheets of the Accessory Controls for more information 3 If any changes are made to the system click a a Update Details to refresh the list of Accessory Controls oom This feature can be useful during installation or trouble shooting 4 Click on Done to close the Accessory Control Details screen Modify Scenes Online Online Scenes located in the Online PS onines Scones Options menu enables you tO modify Unit Currently Being Monitored Save a Scene Currently Selected O Sa s temporary scene preset data from your PC Using your PC Geta a 5 temporarily adjust your lights through the r walwash interrogating familiar GRAFIK Eye Interface to create new scenes by adjusting fade times and wer es zone intensities Use this screen to tweak the light levels in the space just as you would use the physical Control Un
42. ude 33 6 H Longitude 75 1 E Time Zone Easter Time Daylight Savings Time Data Daylight Savings Comection Amount i hour Starting Month Jap Ending Month October Starting Day OF Week Sunday Ending Day OF Week Sunday Starting Day OF Month Fist Ending Day OF Month Starting Time 200am Ending Time Operating Instructions GRAFIK Eyee LIAISON Software Get After Hours Mode Information from the PRG select After Hours Mode from the Online Options menu E iier Hour Mode Enabled LIAISON will display the after hours mode information that Acari ite Was stored In the GRX PRG Or GRX CI PRG hours Ey minutes Click on Done to close online After Hours Mode form fen Une ier Sean Ee Retrieve the Current System Configuration from the GRX PRG or GRX CI PRG In many instances the programming of the GRAFIK Eye system may be done using conventional programming methods instead of LIAISON Or perhaps LIAISON may be used for the initial programming and final adjustments to the lighting are done in the space In these instances it would be desirable to recover the system configuration in a format that could be reviewed or reused at a later time Most system information can be recovered including presets communication information Timeclock events Super Sequence data calendar exceptions and default schedules configuration The only data that cannot be retrieved are Accessory Control names system location and customer circuit informat
43. ume 266 MHz or higher recommended m 32 MB RAM 15 MB of free space on your hard drive VGA Graphics SOFTWARE Microsofte Windowse 95 or later operating system or Microsofte Windowse NT version 4 0 or later LIAISON does not support Microsofte Windowse Vista CD INSTALLATION m Quit all other applications including any anti virus programs by 1 Right clicking on its icon in the System Tray and quitting the program or 2 Pressing Cntrl Alt Delete selecting the process and clicking on the button labeled End Process Insert the GRAFIK Eye LIAISON CD into the CD ROM From Windows START menu select RUN In the RUN box type the letter for your computer s CD ROM drive usually D or E and SETUP Click OK After installation is complete click on the LIAISON icon to run LIAISON To download the latest version of LIAISON visit our website at www lutron com GRAFIK Eyee LIAISON Software Operating Instructions START UP SCREEN GRAFIK Eye LIAISON Lighting Control Software can be used to Create Edit Go Online with or Back up a GRAFIK Eye system Select the mode you wish to use Create or Edit a Project from File This mode can be used without being connected to a GRX PRG or GRX CI PRG Select this mode if you are in the design stage of a project or wish to edit an existing project you have created a project and need to download the data for the first time or you want create a project in
44. view you can add exceptions to every day or every weekday in a single drag and drop action For example to create exceptions for every Sunday select the schedule drag and then drop on Sunday To create exceptions for the entire month select the schedule drag and then drop on April 5 To delete an exception highlight the day and select Delete from the Edit menu 6 When the calendar modifications are complete click on Done to return to the main screen A Create a Super Sequence A Super Sequence is a collection of up to 60 system scene selects called steps and their corre sponding hold times The elements involved with a Super Sequence event are the scene the selected GRAFIK Eye units and the Hold Time m To define a Super Sequence select Super Sequence from the Timeclock menu m Set a Step Steps that have not yet been defined will have No Step End in the Scene to Select column From the first unused step select the desired scene number from the pull down list Select the Units at which the scene will be selected by checking the appropriate Control Units zs LUTRON 15 s aw GRAFIK Eyee LIAISON Software NOTE The selected scene will be activated on each of the Control Units selected for that step For example if Scene 2 and Control Units 1 and 2 A1 and A2 are chosen for a step Control Units 1 and 2 will go to their respective Scene 2 levels using their respective Scene 2 fade times when
45. w Time The new time will be added to the list For Time of Day if AM or PM was omitted but included in the computer s international setting the AM or PM extension will automatically be added based on the current event selected in the list 6 To remove any events highlight the event and then select Delete from the Edit MENT Copy From Copy To menu Weekda Weekda Weekend Weekend 7 To copy one schedule to another click on the Copy Schedule button The Speci Special 2 Copy Schedule screen gives the user the option to copy real time events astronomic events or both to another schedule There is also the option to C Boal Te Everts Oriy overwrite the events or to append the events to the end of the Copy To E E R schedule Copy Options Delete Existing Events First C Append to Existing Events 8 The Copy From list is the schedule of events that will be copied The Copy To list is the schedule to which the events will be copied Use the options to Done set which events will be copied Click and drag a schedule from the Copy From list to a schedule in the Copy To list When the copy is complete click on Done 9 To change schedules select a new item from the Schedule list When the Weekday Weekend and any Special schedules have been defined click on the Done button to exit the Schedule Events screen 10 Select Save from the File menu to save your system changes a Default Schedule
46. y selecting Save from the File menu LUTRON 12 Operating Instructions GRAFIK Eyee LIAISON Software TIMECLOCK MENU E Create a Timeclock Schedule NOTE For each schedule there is a maximum of 60 events allowed Select Schedules from the Timeclock menu to open the Schedule Events screen Follow the steps below to define a schedule 1 Select a Schedule There are four schedule options Weekday Weekend Special 1 and Special 2 The Weekday and Weekend options allow schedules to be defined that will run every weekday or every weekend day by default The Special 1 and Special 2 schedules are used to define sched ules of events for a unique day e g Holiday Party etc Select a schedule to program by clicking on an item from the Schedule list 2 Select Event type Time of Day or IB Schedule Events Weekday Astronomic Select the Time of Day or ickonthelstbelow Time of Day Astronomic Se errr Astronomic tab of the schedule If the _ _ aghedue Aon SCENE UNLOCK Time of Day tab is selected events can SELECT SCENE 1 ZONE UNLOCK be scheduled to occur at a particular Special 1 emi ara Salas time of day or night Astronomic ius areal e a E events can be defined by selecting the oe edule SELECT SCENE 2 eee Astronomic tab Events Can be set to ea ibaa a Conference Room occur up to 2 hours before or up to 2 Type anew time to Peet hours after sunrise OR sunset The time eventis _ i200PM scale corresponding to the eve
Download Pdf Manuals
Related Search