MASKED Electric Screen – instruction - Viz
Contents
1. Hz 3x 1 5 mm a gu Ws D Optional control The electric screen can be upgraded with wireless radio RC or infrared IR controllers When programming the stop positions use the programming manual RC IR A wo mounted receiver IR controls RC F 12V TRIGGER 230V receivers RC Ed Lis 5 EXTEND IR 4 REGULATION front of the screen power cable 1 yellow colour down 2 white colour up nT edge beam of the screen back of the screen POSITION SCREEN UNROLLED Additional adjustment of settings other than factory defaults is possible using the screw marked 1 yellow Only by authorised persons LIMITING SCREEN UNROLLING In order to unroll the screen less than its factory setting turn the key to the left INCREASING SCREEN UNROLLING In order to unroll the screen more than its factory setting by 5 cm at most turn the key to the right An increase in screen unrolling of more than 5 cm may cause permanent damage to the screen POSITION SCREEN ROLLED UP Additional adjustment of settings other than factory defaults is possible using the screw marked 2 white Only by authorised persons LIMITING EDGE BEAM UNROLLING In order to unroll the lower edge screen beam less than its factory setting turn the key to the right INCREASING EDGE BEAM UNROLLING In order to unroll the lower edge screen beam more than its factory setting by 5 cm at most turn the key to the lef2. MASKED Enclosed electrically unrolled screen LIST OF ITEMS Electric screen Mounting elements 2 pcs Button switch Assembly kit Mounting instruction manual 2 INSTALATION AND REGULATION A Dimension table 145 Ste D4 D1 D2 159 D3 D2 20 D5 D2 135 D6 D2 180 SIZE mm D3 D4 D5 WIDTH D2 GAP IN THE CEILING Screw in elements C pins into elements B Then set the place of installation of the screen on a solid ceiling at distances as per table D2 Use wall plugs and screws included in the mounting kit 4x 0 75 mm2 CURRENT DESIGNATION CABLE FROM THE DRIVE CPHASEL EARTH YELLOW GREEN UP DIRECTION BLACK DOWN DIRECTION BROWN C SAFETY in transport Before each transport make sure that the screen is protected in accordance with the guidelines PE foam wee Rea screen housing edge beam elements securing the edge beam C Lift the screen by inserting pins marked C into holes D Adjust nuts E to level the screen and then tighten to ensure stability Using magnets F attach masking elements G Electrical connection diagram for a screen with the radio control option built in PLEASE NOTE The electrical connection should be performed by a person with appropriate certification and in accordance with health and safety regulations 3 x 0 75 mm2 PHASE BROWN NEUTRAL BLUE 230V 50
3. ibility that the products Elecric screens SUPERNOVA SUPERNOVA TENSION MASKED MASKED TENSION ELLIPSE ELLIPSE TENSION BUSINESS Plus to which this declaration relates in accordance with m the Low Voltage Directive 73 23EEC together with the modifications of Directive 93 68 EEC a EMC Directive 89 336 EEC along with its amendments92 31 EEC 93 68 EEC i 91 263 EEC comply with the following European standards EN 60335 2 97 with reference to EN 60335 1 EN 55014 1 EN 55014 2 EN 61000 3 2 EN 61000 3 3 and are CE certified CE
4. ibited to perform any steps that may damage the power supply cord or plug e Do not modify the power cord i e do not make any structural modifications do not pla ce the cord in immediate vicinity of hot objects do not bend or twist the cord do not pull the cord do not place any heavy objects on the cord and do not coil the power cord e Using the equipment with a damaged power cord may cause electrocution or shorting of the circuits and fire e Do not touch the power cord or plug with wet hands e Always follow the guidelines provided in this instruction manual and in the equipment mounting instructions e Before installing the equipment make sure it is complete free of defects compliant with your order and has not sustained damage in transport INSTALLATION GUIDELINES e The equipment should be installed by a qualified engineer in accordance with the guide lines provided in the mounting instructions Electrical connections should be made by a specialist with an appropriate license e Install the equipment using screws and mounting elements appropriate for the conditions of the installation to which the lift is mounted and stable original auxiliary elements dedicated for the specific lift model e After mounting the equipment before first use check if it is mounted as per the instruc tions and level If the equipment is not level adjust the mounting Do not use equ ipment that is not properly installed e Do not modify
5. or unscrew elements of the equipment as this may cause a risk of perma nent damage to the equipment and or the safety of the users WARRANTY CONDITIONS The warranty period for the device is 24 months from the date of purchase indica ted on the original receipt 1 The warranty period for the device s electric drive is 60 months 2 The warrantor commits to fix free of charge damage suffered by a device de livered to the service point that demonstrates defects resulting from defects in workmanship or materials which become noticeable during the warranty period 3 The warranty does not cover a damage caused by use of the device in a manner other than that described in the user manual b damage caused by improper storage or transport c mechanical damage d abrupt changes in electrical grid voltage e disassembly and reassembly 4 Defects will be removed within 14 days from the date the device is accepted on warranty at a service point 5 Service point address Manufactured after 13 08 2005 Do not dispose of used electrical and electronic equipment together with municipal waste due to the presence of substances hazardous to the environment in the equipment Such devices should be delivered to a collection point for recycling Information on collection points is ava ilable from local government authorities or in stores A VLZ ANAT DECLARATION OF CONFORMITY CE VIZ ART AUTOMATION I hereby declare with sole respons
6. t An increase in screen unrolling of more than 5 cm may cause permanent damage to the screen yellow whit 1 2 Screen surface URAN Matt White URAN GREY Cine Grey URAN PROFESSIONAL Professional Matt White URAN PEARLESCENT Pearlescent Image aspekt ratio Square Video Cine 1 1 4 3 16 9 Power supply 230V 50 HZ Manufacturer VIZ ART Automation tel 48 22 6138899 www viz art eu Rules of safe operation of VIZ ART AUTOMATION equipment SAFETY INFORMATION CAUTION To ensure safety of the personnel make sure to follow the guidelines provided in this instruction manual Keep the instruction manual for future reference e Do not allow children to play with the device controller switch or remote control e Do not leave device controllers within the reach of children e Inspect the equipment assembly periodically to identify and repair any damages e f any damages are identified do not use the equipment until the necessary repairs are made e Keep appropriate distance from the equipment during operation In case of a failure the equipment may constitute a risk of injury or wounds e Do not install any items other than those specified in the equipment instruction manual All installation and mounting works should be done by an engineer with appropriate li censes e Inappropriate mounting may damage the product or cause injury e Use only elements compliant with the mounting instructions e t is proh
Download Pdf Manuals
Related Search