Turbhogar - Rofer y Rodi Chimeneas
Contents
1. Manual de uso y montaje Manual of assembly and use Manuel d utilisation et de montage i Benutzer und Montagehandbuch RO MEN E TURBHOGAR MANUAL OF ASSEMBLY AND USE A The proper functioning of the TURBHOGAR Fireplace will depend on its correct installation and use To ensure this read this manual carefu lly and follow the general instructions and those pertaining to each model in the respective technical data section The TURBHOGAR fireplace is a model of open fireplace that is designed to provide the maximum amount of calorific energy while achieving the most economical performance and providing the greatest degree of safety The heat given off directly by radiation is added to by that obtained from the efficient system of hot air heating driven by its two turbines This enables us to heat up more quickly the space in which the TURBHOGAR fireplace is installed by means of its front air outlets Moreover and thanks to its two upper outlets the hot air can be conveyed to other rooms in the house With the TURBHOGAR fireplace the fuel will be exploited to good effect as It is fitted with a device for regulating the draught by means of an upper switch and one for controlling the influx of combustion air through an adjustable lower grate In this way the consumption of fuel can be optimised according to the room temperature requirements at any given time Finally it is important to point2. Malaga Espa a Tel 95 254 2316 e Fax 95 254 4973 e e mail rofer rofer com www rofer com om
3. high heating power of the fireplace we do not recommend its installation in small rooms as the resulting increase in temperature could cause a heat shock hazardous to persons health For this reason the device should not be used during hot days or periods e Below is a detailed list of instructions on how to correct and avoid an irregular functioning of the device and some example cases of failure with indications on how to repair the problem IMPORTANT NOTE the repair work or procedures indicated with an asterisk must be carried out by qualified professional staff table 1 Description of failure Probable cause Procedure Turn the switch to position 0 This will automatically disconnect the turbines The turbines continue to function manualconnecian after a time Switch is in position H after the device has been turned off Disconnect the device from the electricity Failure of thermostat mains and do not use again until the device has been repaired The switch is in position As the temperature is falling 0 automatic disconnection is automatically activated connection Press position II if you wish to continue heating the room The turbines stop while the device is Check that the plug is correctly inserted in i i No electrical supply in operation the socket Disconnect the device from the electricity Turbine failure mains and do not use again until the device has been repaired Failure
4. in the electrical The protection circuit differential of installation of the Disconnect the device from the electricity the dwelling is activated when the dwelling or in the device mains and do not use again until the turbines start functioning device has been repaired TOR Malfunction of the Disconnect the device from the electricity The turbines function in automatic i h turbine switch mains and do not use again until the mode but not in manual mode device has been repaired 14 ROFER 8 RODI FIREPLACES TURBHOGAR Complementary sheet to the Manual of Installation and Use table 2 Irregular function Probable cause Course of action Close the hot air outlets in the rooms that Reduction in the hot air are not being used You have probably Excess of hot air outlets flow installed more outlets than the recommended number for your fireplace quality recommended in the user s manual generate sufficient heat amount of firewood recommended in the user s manual The premises may be too large for the type of fireplace installed or they are poorly insulated Use dry not damp or green firewood To ensure the firewood sets alight it is The firewood pieces are advisable to use small branches or twigs too large that burn well Use split firewood to stoke up the hearth once lit Open the draught regulator and once the firewood has caught fire sufficiently close the draught again The pre
5. kg 117 kg 9 12 kg 12 15 kg Fireplace made of electro soldered steel i 15 20 plate 5mm i i Door with vitro ceramic glass guaranteed to resist up to 7502 C Draught adjustable by means of external handle Removable ashes box with air inlet control Heat chamber with turbines and thermostat T Stainless steel door handles and knobs 4 65 80 ia 49 52 58 65 26 R ROFER amp RODI TURBHOGAR Complementary sheet to the Manual of Installation and Use Complementary sheet to the Manual of Installation and Use Review 281108 TURBHOGAR Models Alfa Beta Delta Epsilon Lambda Neo Sigma Family Models TURBHOGAR Models Alfa Beta Delta Epsilon Lambda Neo Sigma Heating power i_ ae kW Energetic Performance materials of Oxygen Temperature of smoke emissions 430 C Insertable fireplace that uses natural firewood as fuel for intermittent use and which functions with the door closed Read and follow the instructions for installation and use Use only the recommended fuels ROFER amp RODI FIREPLACES 9 TURBHOGAR Complementary sheet to the Manual of Installation and Use Warning for installer and user Add to the beginning of page 3 e The installation of the fireplace and of the smoke duct should be carried out in observance of all the local regulations including those referring to national and European norms e An incorrectly installed fireplace or one with a defe
6. out that the TURBHOGAR as compared with traditional open fireplaces provides greater safety as it comes with a vitro ceramic glass door an anti opening system and an electrical circuit controlled by thermostat R ROFER amp RODI 15 TURBHOGAR MANUAL OF ASSEMBLY AND USE Assembly TURBHOGAR Heat ducts Whilst the brickwork is being done the front section of the TURBHOGAR fireplace should be protected against plaster remains or water falling onto the device as this could damage the paintwork or cause rusting Do not rest the brickwork decorative fittings or wood directly on the TURBHOGAR fireplace A channel of at least 4mm should be left between the decorative fittings and the front section of the device This is to allow for any expansion of the device and avoids cracks appearing in the decorative fittings An interior air chamber of at least 5cm should be left between the lateral decorative fittings the back wall and the main body of the fireplace Under no circumstances should the TURBHOGAR be coated with fibre glass sheets or other types of insulating material To convey hot air to other rooms the TURBHOGAR fireplace is fitted with two upper outlets The connection is made with a flexible aluminium pipe by first removing the cover and then inserting an adjustable grille in the outlet The connections should be fastened with metal clamps The fireplace hood should be made ideally from bulkhead set in plaster A gr
7. Connection of the heat ducts 1 Remove the upper cover of the Turbhogar 2 Insert the metallic connector supplied fireplace using a screwdriver to lever the edge which will serve as a joint for the flexible heat of the cover pipe m Front hot air outlets n E g n Smoke outlet Removable Draught control handle ashes box Turbine switch key Grille with air Door with vitro ceramic glass cn inlet control Turbines and thermostat Handles for transportation Heating capacity 10 000 kcal h 14 000 kcal h Maximum firewood load 8 10 kg 11 13 kg 920 25 Fireplace made of electro soldered steel plate 5mm Door with vitro ceramic glass guaranteed to resist up to 750 C Stainless steel handles and knobs 58 65 Draught adjustable by means of external handle Removable ashes box with air inlet control an Heat chamber with turbines and thermostat 65 80 43 46 _ R ROFER amp RODI 25 WT oooosooon ATT EN TURBHOGAR MANUAL OF ASSEMBLY AND USE Technical data SIGMA Model Upper hot air outlets Smoke outlet Front hot air outlets Draught control handle Door with vitro ceramic glass Anchors for transportation Removable ashes box Folding cover This model has an air inlet control grille turbines and a Handles for transportation switch key behind the folding cover 12 000 kcal h 16 000 kcal h 86
8. amage and even fire due to the heat radiation For this reason do not place inside the indicated area wood or plastic furnishings wallpaper fitted carpeting carpet rugs curtains etc e Once the fireplace is functioning the door must be kept closed except when opening to refuel e This device is not an incinerator Do not use it to burn domestic waste cardboard magazines etc ROFER amp RODI FIREPLACES 11 TURBHOGAR Complementary sheet to the Manual of Installation and Use Maintenance Add to the end of page 8 e In order to prevent the soot accumulated in the chimney draught catching fire we recommend a periodic check and cleaning of the draught installation using mechanical means carried out by qualified technical staff at least once a year e In the event of this soot catching fire close the chimney draught and call the fire service immediately Spare Parts e To order spare parts indicate the serial number and year of manufacture figuring on the plate attached to the device or on the warranty card Only original spare parts must be used Parts replaceable only by qualified professional staff Electrical cables Turbines Thermostat Switch Parts replaceable by the user Draught break plate Firedog Ashes grate Ashes box Grille knobs Vitro ceramic glass bear in mind that although resistant to temperature it is fragile and any impact to it or to the fireplace may cause it to break In order to replace i
9. ata DELTA 2 DELTA 3 Model Connection of the heat ducts 1 Remove the upper cover of the Turbhogar 2 Insert the metallic connector supplied fireplace using a screwdriver to lever the edge which will serve as a joint for the flexible heat of the lid pipe Hot air outlets n 2 with adjustable grilles BE se __ Door with Draught vitro ceramic glass control handle Smoke outlet Removable ashes box Turbine switch key Grille with air inlet control Handle for transportation Turbines and thermostat After transporting the fireplace remove the auxiliary handles and install the lateral grille pressing on the corners Do not use a hammer as the blows may cause deterioration to the paintwork Reference 65 65 D 65 C 80 80 D 80 C Diameter of Smoke Ducts 20 cm 25 cm Flexible hot air pipe 13 cm 13 cm Heating capacity 10 000 kcal h 14 000 kcal h Weight 91kg 91kg 87kg 120kg 120kg 115 kg Maximum firewood load 8 10 kg 11 13 kg 820 25 e Fireplace made of electro soldered cI lr St steel plate 5mm f _ Tj e Door with vitro ceramic glass guaranteed to resist up to 7502 C e Stainless steel handles and knobs 58 65 Draught adjustable by means of external handle Removable ashes box with air inlet control Heat chamber with turbines and thermostat 24 R ROFER amp RODI TURBHOGAR MANUAL OF ASSEMBLY AND USE Technical data NEO Model
10. ctive chimney installation could cause damage to the apparatus and set on fire the soot accumulated in the chimney draught causing a risk of fire back puffing smoke etc e The manufacturer refuses any responsibility for damage or deterioration caused by the use of fuels not recommended or by unauthorised alterations made to the device or the installation The installation and repair of the device as well as the periodic maintenance of the chimney draught must be carried out by qualified professionals e Failure to observe the instructions for installation and use will result in the invalidation of the manufacturer s warranty Assembly Add to the end of page 5 e To guarantee the correct insulation of the fireplace and chimney fire bricks ceramic and steel plates etc can be used The safety distance for adjacent combustible materials must be observed e The floor surface on which the chimney is placed should be able to support the load or total weight of the fireplace decorative fittings and hood In the event of this condition not be observed the forging work can be reinforced by means of a metal structure or the load can be distributed by the laying of a reinforced concrete slab Consult a qualified technician before carrying out any of these measures e If the dwelling is fitted with mechanical air conditioning units or extractors when these begin to function the air intake for the chimney draught is likely to be insufficient and
11. cumstances should liquid fuel or coal briquettes be used to light the fire To help in the lighting of the fire a mixture of fine and bulky firewood can be used Once it is functioning when opening the door to refuel do so Slowly to avoid the back puffing of smoke Observe the maximum load indicated During the first lighting some smoke may appear as a result of the drying of the protective coat of heat resistant paint in the TURBHOGAR fireplace For this reason we recommend that you ventilate the area until this smoke disappears To improve the performance of the TURBHOGAR fireplace there is an adjustable draught operated by a handle located on the upper section To open the draught turn to horizontal position To close the draught turn to vertical position which prevents the door from opening The lighting of the fire is helped by opening the adjustable grille on the ashes box and opening the draught When the fire has taken well the grille can be closed and adjust the draught in order to reduce fuel consumption The draught must never be closed when the door is open In order to control the flow of hot air the TURBHOGAR fireplace is fitted with a three position switch Position O Automatic mode minimum speed Position I Manual Mode minimum speed Position Il Manual Mode maximum speed R ROFER amp RODI 19 TURBHOGAR MANUAL OF ASSEMBLY AND USE Lighting and Control At position O due to the action of the the
12. e fireplace or use of inadequate material A check on the ducts a hood should be carried out by qualified professional staff ROFER amp RODI FIREPLACES 15 TURBHOGAR Complementary sheet to the Manual of Installation and Use CE Declaration of compliance C E The manufacturer hereby Certifies that the fireplace models listed below meet all the requirements of the EU Directive governing construction products 89 106 EEC and comply with regulations UNE EN 13229 2001 Insertable devices including open fireplaces 2003 which use solid fuels test requirements and methods amended by UNE EN 13229 AC UNE EN 13229 A1 2003 UNE EN 13229 2002 A2 2005 UNE EN 13229 AC 2006 and UNE EN 13229 2002 A2 2005 AC 2006 Commercial brand ROFER amp RODI Family Models TURBHOGAR models Alfa Beta Delta Epsilon Lambda Neo Sigma Description Insertable device using natural firewood as fuel for intermittent use and functioning with the door closed Heating power 12 kW Energy performance 70 Public Organism notified N 1722 CEIS Manufacturer ROFER AXARQUIA S L Vega Melilla plot 1 P O Box 81 29740 TORRE DEL MAR Malaga SPAIN Ft F 7 fa SF pe Fi i L Signed Andres Roman Cort s Technical Director 16 ROFER amp RODI FIREPLACES tradiciondisenocalidad R1 07 ROFER amp RODI itl IM Ee IN CE A Apdo de Correos 81 e Ctra Malaga Almeria km 269 e 29740 TORRE DEL MAR
13. e use of a Stainless or vitrified steel pipe with a bracket joint In the event of an exterior assembly this should be of a modular double panel type Avoid reducing the diameter of the pipe the use of elbow bends of more than 452 and the connection of various devices to the same duct as this could cause the back puffing of smoke In the event of requiring insulation in a section of the chimney draught we recommend the use of ceramic heat resistant panels The chimney draught should have a minimum height of 4m and rise to at least 50cm above the highest section of the roof It should be placed at a distance of over 8m from any adjacent building For the top of the chimney it is advisable to use standardised prefabricated or metallic hoods When joining together the pipes the nozzle end should be pointing upwards To ensure a faultless sealing in the section that passes through the hood between the TURBHOGAR fireplace and the wrought ironwork heat resistant putty may be used 18 R ROFER amp RODI TURBHOGAR MANUAL OF ASSEMBLY AND USE Lighting and Control Before lighting the TURBHOGAR fireplace ensure that the draught is open horizontal handle Whilst the device is functioning at least one of the hot air outlet grilles must remain open You are advised to use dry firewood with low resin content for example olive or evergreen oak Wafer board or wood with paint or varnish remains should not be used Under no cir
14. for this operation Removable corsaire plate TURBHOGAR SECTION 20 R ROFER amp RODI TURBHOGAR MANUAL OF ASSEMBLY AND USE Diagram and Connection to the electricity mains During the normal use of the device and whilst it is lit you are advised not to disconnect it from the electrical mains However a permanent connection must not be made in the fuse box but preferably by means of an approved plug with an earth wire which when required allows the user to disconnect it Z Remember that your fireplace is connected to the electrical mains It must not be extinguished with water as in addition to causing a Safety hazard it could damage the device and its electrical components Resistance Thermostat Diagram of the electrical connection Any repair work to or handling of the Turbhogar model particular the electrical system must be carried out by authorised technical staff For any information related to the assembly use or maintenance of your fireplace which is not contained in this manual please do not hesitate to contact the nearest Rofer amp Rodi Fireplace Dealer R ROFER amp RODI 21 en TURBHOGAR MANUAL OF ASSEMBLY AND USE Technical data ALFA Model Upper hot air outlets Hot air outlets Smoke outlet with adjustable grilles Draught control handle Door with vitro ceramic glass Anchors for transportation Ashes box with i adjustable grille Handles for
15. ille can be fitted in this hood to enable ventilation of the air chamber and avoid cracks occurring 16 R ROFER amp RODI TURBHOGAR MANUAL OF ASSEMBLY AND USE Assembly Hood ventilation grille optional Outlet of hot air on same floor Hot air outlet optional in upper floor Flexible aluminium pipe Smoke outlet in stainless for heating or vitrified steel Front hot air outlets a TURBHOGAR fireplace section Cold air inlets The TURBOHOGAR fireplace ducts and hood should not be installed next to coatings wood parquet or other potentially inflammable elements Nor is the installation authorised in houses with wooden frames beams or roof or asphalt roofing felt No installation in the house should be passed through the interior of the chimney duct or hood A safety distance of 0 5m should be maintained where the installation passes near electrical conduits or other installations The site of the fireplace installation should have sufficient ventilation to provide a draught and allow for air recycling In the event of it being Insufficient an exterior air inlet grille can be fitted as close as possible to the fireplace R ROFER amp RODI 17 en FS CA TURBHOGAR MANUAL OF ASSEMBLY AND USE Smoke ducts A metallic pipe of a specified diameter must be used for the evacuation of smoke through the draught In accordance with current regulations we recommend th
16. it will be necessary to install an exterior air inlet grille which must not be sealable as close as possible to the fireplace with a minimum section size of 100 cm2 As a general rule we recommend the installation of this type of grille as it guarantees an adequate combustion and chimney draught 10 ROFER amp RODI FIREPLACES TURBHOGAR Complementary sheet to the Manual of Installation and Use Smoke ducts Add to the end of page 6 e The smoke duct and the hood of each device should be individual Do not connect 2 or more heating devices to the same smoke duct e Where necessary fit dampers to ensure that the installation of the smoke ducts and the chimney coping hood do not obstruct the mechanical removal of soot from the chimney draught Lighting and Adjustment Add to the beginning of page 7 e Contact with the lighted stove or with the vitro ceramic glass can cause burns For this reason in order to adjust the draught and open the door you should use the handle supplied with the device e For safety reasons do not allow children to go near the lighted fireplace moreover once extinguished take the necessary precautionary measures as the device will remain hot for a certain period of time afterwards e A safety distance of 1 2 m around the device should be observed inside which no potentially inflammable materials should be placed Take into account that even though there may be no direct contact there may exist a risk of d
17. mises are poorly insulated The firewood is damp The fire does not light sufficiently or goes out The chimney draught is closed Open the lower air inlet and keep it open The air inlet is closed for as long as is necessary The chimney draught is Adjust the draught control and close open completely if necessary The air inlet is open Close the lower air inlet The fire is too high Avoid using certain types of wood that The firewood is of a poor cause rapid burning such as chipboard quality ply wood carpentry shop wood shavings and sawdust pine wood etc The fire needs to be high as soon as it is The smoke outlet duct is lit in order to heat up the duct To achieve cold this use fuel briquettes for barbeques and fireplaces Check that there is no blockage in the The chimney draught is duct particularly at hood level Where blocked necessary clean out the soot mechanically Smoke emanates during Check that the exterior air inlets are not the lighting process or blocked It may be necessary to lengthen when the device is the smoke ducts in order to obtain the functioning optimal chimney draught suction In specific cases it may cause a suction that prevents the device from functioning correctly In such event it will be necessary to install an external air inlet next to the fireplace The draught is insufficient Use of ventilators or mechanical extractors A defective installation of th
18. rmostat the turbines start func tioning automatically once a specified temperature has been reached normally 20 30 minutes after the lighting in the same way the turbines switch off when the temperature of the TURBHOGAR fireplace drops To get full benefit from the heating power of the TURBHOGAR fireplace we recommend using Position II as its greater air flow is specially desig ned for the conveying of air to other rooms or for heating up an area more quickly Once the desired room temperature has been reached Position I can be used If you want the turbines to switch off automatically after the fire has been put out switch to Position O O C__ 3 Safety Handle for the opening of the door and the control of the draught Maintenance For the cleaning of the exterior a dry cloth should be used and should not be moistened or used with any abrasive product that may damage the paintwork The glass should be cleaned when cold using a product specially designed for fireplaces or any brand of oven cleaner In the event of persistent stains a glass scraper can be used The cleaning out of the ashes is done by removing the interior fireplace grille and collecting up the ashes in the box making sure beforehand that the live embers are fully extinguished For the periodic removal of soot from your chimney we recommend that you seek professional advice The draught shutter blade of the TURBHOGAR fireplace is detach able to allow
19. t the use of specialised tools may be required and adequate protection measures need to be taken to avoid suffering cuts during the handling of broken glass 12 ROFER amp RODI FIREPLACES TURBHOGAR Complementary sheet to the Manual of Installation and Use Technical data Add to the beginning of page 10 e The TURBHOGAR fireplace is an insertable device which conforms with the obligatory UNE EN 13229 regulations Normal heat output Performance CO concentration at 13 oxygen Smoke flow Optimum draught suction Average smoke temperature 430 C Combustion chamber Closed Type of combustion Intermittent wood Diameter 18 cm Recommended type of firewood Beech oak Chestnut elm olive holm oak etc The size weight and other characteristics of each model are set out in the relevant technical catalogue ROFER amp RODI FIREPLACES 13 TURBHOGAR Complementary sheet to the Manual of Installation and Use Probable causes of failure or irregular functioning e The device you have purchased is a high performance fireplace of guaranteed quality Nevertheless certain extreme climate conditions such as strong winds hail storms or risks of freezing temperatures may cause the chimney draught to be inadequate In view of the potential risk of back puffing smoke we advise you not to use the fireplace under such conditions as this will not be considered as a defect or malfunction of the device e Owing to the
20. transportation Turbines and thermostat Heating capacity 12 000 kcal h 16 000 kcal h Maximum firewood load 9 12 kg 12 15 kg 617 5 20 1 yit a Fireplace made of electro a soldered steel plate 5mm LELLI Door with vitro ceramic glass guaranteed to resist up to 7502 C 58 65 Draught adjustable by means of external handle r Bronze handles and knobs rer Removable ashes box with air inlet control e Heat chamber with turbines p 65 80 E do 49 52 and thermostat L 22 R ROFER amp RODI TURBHOGAR MANUAL OF ASSEMBLY AND USE Technical data BETA Model Upper hot air outlets P Smoke outlet Hot air outlets with adjustable grilles ar F Draught control handle Double door with Anchor for vitro ceramic glass o o transportation Ashes box with adjustable grille Turbines and thermostat Handles for transportation Reference Diameter of Smoke Ducts 16 000 kcal h 128 kg 12 15 kg Heating capacity Weight Maximum firewood load Fireplace made of electro soldered steel plate 5mm Double door with vitro ceramic glass guaranteed to resist up to 7502 C Draught adjustable by means of external handle Bronze handles and knobs Removable ashes box with air inlet control Heat chamber with turbines and thermostat ao J 55 R ROFER amp RODI 23 M en TURBHOGAR MANUAL OF ASSEMBLY AND USE Technical d
Download Pdf Manuals
Related Search