L 76475 FL L 76675 FL EN User manual
Contents
1. CAUTION Do not put cardboard wood or equivalent materials below the A appliance feet to adjust the level 13 4 The inlet hose Do not use an extension hose if the inlet hose is too short Con tact the service centre for the re placement of the inlet hose i Water stop device ENGLISH 29 e Connect the hose to the appliance Turn the inlet hose only left or right Loose the ring nut to set it in the cor rect position e Connect the water inlet hose to the cold water tap with 3 4 thread CAUTION Make sure that there are no leaks from the couplings The inlet hose has a water stop device This device prevents water leaks in the hose because of its natural ageing The red sector in the window A shows this fault If this occur close the water tap and contact the service centre to replace the hose 30 www aeg com 13 5 Water drainage There are different procedures to con nect the drain hose With the plastic hose guide On the edge of a sink Make sure that the plastic guide can not move when the appliance drains Attach the guide to the water tap or the wall To a stand pipe with vent hole Refer to the illustration Directly into a drain pipe at a height of not less than 60 cm and not more than 100 cm The end of the drain hose must always be ventilated i e the inner diameter of the drainp2. To L 76475 FL EN User manual L 76675 FL WAEG perfekt in form und funktion 2 www aeg com CONTENTS oNOAVWRWDNMN SAFETY INFORMATION 2 0348 een asp d Ba yd SAFETY INSTRUGTIONS 24 422 ee ee ea esd TECHNICAL INFORMATION 00 0 0 sense nenne nenn PRODUCT DESCRIPTION 3 22 4 bed Sie de ea ha CONTROEPANEL sr a aa een a PROGRAMME Sen ar nt a creat cael ee en a ee er he CONSUMPTION VALUES 2 00 dite ial en chin x BEFORE FIRST USE eu ne eh a ehe 92 BAITU SEn aie ate ee ee a Ara eis re ee ee 10 HINTSANDTIPSE cA A ee een 11 EAREAND CLE NING 4 5322 22 a en ee a a Buche 12 TROUBLESHOOTING dree diaii mane eect eee EG 13 INSTALLATION insets Wits don Sa Raine hae aed hae een Dia FOR PERFECT RESULTS Thank you for choosing this AEG product We have created it to give you impeccable performance for many years with innovative technologies that help make life simpler features you might not find on ordinary appliances Please spend a few minutes reading to get the very best from it Visit our website for Get usage advice brochures trouble shooter service information www aeg com Register your product for better service www aeg com productregistration Buy Accessories Consumables and Original spare parts for your appliance www aeg com shop iw amp CUSTOMER CARE AND SERVICE We recommend the use of original spare parts When contacting Service ensure
3. Open the door and remove all the items from the drum 6 10 11 ENGLISH 27 Put one of the polystyrene packag ing elements on the floor behind the appliance Carefully put down the appliance with the rear side on it Make sure not to damage the ho ses Remove the polystyrene protection from the bottom Pull up the appliance in vertical po sition Remove the power supply cable and the drain hose from the hose hold ers Remove the three bolts Use the key supplied with the appliance Pull out the plastic spacers 28 www aeg com 12 Put the plastic caps in the holes You can find these caps in the user manual bag i We recommend that you keep the packaging and the transit bolts for when you move the appliance If the appliance is delivered in the winter months when there are minus temperatures Store it at room temperature for 24 hours before using for the first time 13 3 Positioning and levelling Install the appliance on a flat hard floor e Make sure that carpets do not stop the air circulation below the appliance e Make sure that the appliance does not touch the wall or other units e Loosen or tighten the feet to adjust the level A correct adjustment of the appliance level prevents the vibration noise and the movement of the appli ance when in operation e The appliance must be level and sta ble
4. Remove the top part of the liquid additive compartment 4 Clean all the parts with water 5 Clean the dispenser recess with a brush 6 Put back the dispenser in the recess 11 7 Drain pump i Clean the pump if e The appliance does not drain the wa ter Regularly examine the drain pump and make sure that it is clean e The drum cannot turn e The appliance makes an unusual noise because of the blockage of the drain pump e The display shows an alarm code be cause of the problem with water drain WARNING 1 Disconnect the mains plug from the mains socket 2 Do not remove the filter while the appliance oper ates Do not clean the drain pump if the water in the ap pliance is hot The water must be cold before you clean the drain pump ENGLISH 21 To clean the drain pump Open the drain pump door Pull the flap out to remove it Put a container below the recess of the drain pump to collect the water that flows out Press the two levers and pull for ward the drainage duct to let the water flow out When the container is full of water put the drainage duct back again and empty the container Do steps 4 and 5 again and again until no more water flows out from the drain pump Pull back the drainage duct and turn the filter to remove it Remove fluff and objects from the pump Make sure that the impeller of the
5. Start Pause button Start Pauze Delay start button Startuitstel E Time saving button Tijd Besparen Extra rinse button Extra Spoelen Ei Stain button Vlekken 9 Spin reduction button TPM Temperature button Temp C 5 1 On Off button Press this button to activate or deacti vate the appliance A tune sounds when the appliance is activated The AUTO Stand by function automati cally deactivates the appliance to de crease the energy consumption when e You do not use the appliance for 5 mi nutes before you press button Jy All settings are cancelled Press button fj to activate the ap pliance again Set again the washing programme and all possible options 8 www aeg com e After 5 minutes from the end of the 5 2 Programme knob washing programme Refer to At the end of programme Turn this knob to set a programme The related programme indicator comes on 5 3 Display The display shows A The maximum temperature of the programme B The default spin speed of the programme e No Spin and Rinse Hold symbols C The display symbols 2 Symbols Description Washing phase E Rinse phases Spin phase Child lock Lor You cannot open the appliance door when the symbol is on You can open the door only when the symbol goes off If the programme is completed but the symbol stays on e There is water in the drum e The Rinse Hold funct
6. Descaling The water we use contains limescale If it becomes necessary use a water softener to remove limescales Use a special product made for washing machines Obey the instructions that you find on the packaging of the manufactur er Do this separately from the laundry wash 11 2 External cleaning Clean the appliance only with soap and warm water Fully dry all the surfaces 11 4 Door seal Do not use alcohol solvents or chemical products 11 3 Maintenance wash With the low temperature programmes it is possible that some detergent stays in the drum Make regularly a maintenance wash To do this e Empty the laundry from the drum e Set the hottest cotton wash pro gramme e Use a correct quantity of powder de tergent with biological properties After each wash keep the door open for a while to prevent mould and to let un pleasant smells go out Regularly examine the seal and remove all objects from the inner part 11 5 Drum Regularly examine the drum to prevent limescale and rust particles Only use special products to remove rust particles from the drum To do this e Clean the drum with special product for stainless steel e Start a short programme for cotton at the maximum temperature with a small quantity of detergent 20 www aeg com 11 6 Detergent dispenser To clean the dispenser 1 Press the lever Pull the dispenser out 3
7. add the stain phase to a programme Use this function for laundry with hard stains to remove When you set this function put the stain remover into compartment LL J i This function increases the pro gramme duration This function is not available with a temperature lower than 40 C 5 9 Spin button K Press this button to e Decrease the maximum speed of the spin phase when you set a pro gramme speeds available with the set programme e Deactivate the spin phase e Activate the Rinse Hold function Set this function to prevent fabric creases The appliance does not drain the wa ter when the programme is comple ted The display shows only the spin 10 www aeg com Spin phase is off J Rinse Hold function is on 5 10 Temperature button Press button fd to change the default temperature cold water 5 11 Acoustic signals function You can hear the acoustic signals when e You activate the appliance e You deactivate the appliance e You press the buttons e The programme is completed e The appliance has a malfunction To deactivate activate the acoustic sig nals press button BJ and button J at the same time for 6 seconds i If you deactivate the acoustic sig nals they continue operate only when you press the buttons and when a malfunction occurs 5 12 Child lock function This function prevents children to play with the control panel 6 PROGRAMME
8. adds some rinses 4 The default phase of the spin speed is related to cotton items Set the spin speed Make sure that it agrees with the laundry To select the DRAIN programme only set the function NO SPIN 5 Press EXTRA RINSE button to add rinses With a low spin speed the appliance performs delicate rinses and a short spin ENGLISH 13 6 Set this programme to decrease the time and the consumption of energy and water 7 STANDARD PROGRAMMES for the Energy Label consumption values According to regulation 1061 2010 these programmes are respectively the standard 60 C cotton programme and the standard 40 C cotton programme They are the most efficient programmes in terms of combined energy and water consumption for washing normally soiled cotton laundry Set this programme to have a good washing results and decrease the energy consumption The time of the washing programme is extended 7 CONSUMPTION VALUES i At programme start the display shows the duration programme for the max imum load capacity During the washing phase the programme duration is automatically calcula ted and can greatly be reduced if the laundry load is lower than the maxi mum load capacity e g Cotton 60 C maximum load capacity 7 kg the pro gramme duration exceeds 2 hours real load 1 kg the programme duration don t reach 1 hour When the appliance is calculating the real programme duration a dot blinks in the display
9. area is high or moderate we recommend that you use a water softener for washing ma chines In areas where the water hard ness is soft it is not necessary to use a water softener To know the water hardness in your area contact your local water authority Obey the instructions that you find on the packaging of the products Equivalent scales measure the water hardness e German degrees dH e French degrees TH e mmol l millimol for each litre inter national unit for the hardness of wa ter e Clarke degrees Laundry without hems or with cuts Underwired bras Use a washing bag to wash small items e Avery small load can cause balance problems with the spin phase If this occurs adjust manually the items in the tub and start the spin phase again 10 2 Stubborn stains For some stains water and detergent is not sufficient We recommend that you remove these stains before you put the items in the appliance Special stain removers are available Use the special stain remover that is applica ble to the type of stain and fabric Water hardness table ENGLISH 19 Water hardness Level T gt dH T H mmol l Clarke 1 soft 0 7 0 15 0 1 5 0 9 2 medium 8 14 16 25 1 6 2 5 10 16 3 hard 15 21 26 37 2 6 3 7 17 25 4 very hard gt 21 gt 37 gt 3 7 gt 25 11 CARE AND CLEANING CAUTION IN WARNING Disconnect the appliance from the mains supply before you clean it 11 1
10. i The data of this table are approximate Different causes can change the da ta the quantity and type of laundry the water and ambient temperature Programmes Load Energy Water Approxi Remain Remain kg consump con mate ing ing tion sump pro mois mois kWh tion li gramme ture ture tre duration 1 1 mi 176475 L76675 nutes FL FL Cottons60 C 7 15 7 9146 5 My Cottons 40 C 7 0 78 70 161 52 44 Ai 40 35 0 47 50 171 35 35 Pola 40 35 0 53 62 121 35 35 Wool Hand wash 30 C 2 O22 bi 2 Standard cotton programmes N 60 7 0 72 45 232 52 44 cotton Standard 60 35 0 62 33 190 52 44 C cotton Standard 40 QE 0 46 34 186 52 44 C cotton 1 At the end of spin phase 14 www aeg com Off Mode W 0 48 Left On Mode W 0 48 The information given in the charts above are in compliance with the EU Com mission regulation 1015 2010 implementing directive 2009 125 EC 8 BEFORE FIRST USE 1 To activate the drain system put 2 li tre of water in the main wash com partment of the detergent dispens er Put a small quantity of detergent in the main wash compartment of the 9 DAILY USE Open the water tap Connect the mains plug to the mains socket Press button fj to activate the ap pliance Put the laundry in the appliance Use the correct quantity of deter gent and additives Set and start the correct programme for the type of laundry and soil detergent dispe
11. socket e Do not change the specification of this appliance e Obey the maximum load volume of 7 kg refer to the Programme chart chapter 4 www aeg com e fthe supply cord is damaged it must be replaced by the manufacturer its service agent or similarly quali tied persons in order to avoid a hazard The operating water pressure minimum and maxi mum must be between 0 5 bar 0 05 MPa and 8 bar 2 SAFETY INSTRUCTIONS 0 8 MPa The ventilation openings in the base if applicable must not be obstructed by a carpet e The appliance is to be connected to the water mains using the new supplied hose sets Old hose sets must not be reused 2 1 Installation Remove all the packaging and the transit bolts Keep the transit bolts When you move the appliance again you must block the drum Do not install or use a damaged appli ance Do not install or use the appliance where the temperature is less than 0 C or where it is exposed to the weather Obey the installation instruction sup plied with the appliance Make sure that the floor where you in stall the appliance is flat stable heat resistant and clean Do not install the appliance where the appliance door can not be fully opened Always be careful when you move the appliance because it is heavy Always wear safety gloves Make sure that there is air circulation between the appliance and the floor Adjust the feet to have the necessar
12. solid parti IPX4 cles and moisture ensured by the protective cover except where the low voltage equipment has no protection against moisture 6 Wwww aeg com Water supply pressure Minimum 0 5 bar 0 05 MPa Maximum 8 bar 0 8 MPa Water supply 1 Cold water Maximum load Cotton 7kg Spin speed Maximum 1400 rom L 76475 FL 1600 rem L 76675 FL 1 Connect the water inlet hose to a water tap with a 3 4 thread 4 PRODUCT DESCRIPTION Worktop Detergent dispenser Control panel Door handle Rating plate E Drain pump Feet for the appliance level Ei Water drain hose 9 Water inlet valve Mains cable Transit bolts Feet for the appliance level 4 1 Accessories ENGLISH 7 Spanner To remove the transit bolts Plastic caps To close the holes on the rear side of the cabinet after the removal of the transit bolts Anti flood inlet hose To prevent possible leakage Plastic hose guide To connect the drain hose on the edge of a sink 5 CONTROL PANEL Ke ae 0 OlKatoen Super Eco D Voorwas 20 Min 3 kg Oj Extra Stil Kort Intensief Synthetica Jeans 0 D Voorwas Gordijnen D Strijkvrij Spoelen Fine Was S eS eS Centr ide IZ r B ij Start Wol Zijde 2 Ewa Tjd Sa Pompen Aan Uit 0 Temp C TMP Vlekken Spoelen Besparen uitstel Start Pauze Coe Loo o On Off button Aan Uit Programme knob Display
13. that you have the following data available The information can be found on the rating plate Model PNC Serial Number A Warning Caution Safety information i General information and tips ws Environmental information Subject to change without notice ENGLISH 3 1 SAFETY INFORMATION Before the installation and use of the appliance careful ly read the supplied instructions The manufacturer is not responsible if an incorrect installation and use cau ses injuries and damages Always keep the instructions with the appliance for future reference 1 1 Children and vulnerable people safety WARNING Risk of suffocation injury or permanent disability e This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved e Do not let children play with the appliance e Keep all packaging away from children e Keep all detergents away from children e Keep children and pets away from the appliance door when it is open e Ifthe appliance has a child safety device we recom mend you activate it e Cleaning and user maintenance shall not be made by children without supervision 1 2 General Safety e Before maintenance deactivate the appliance and disconnect the mains plug from the mains
14. 2 Wait for some minutes 3 Make sure that no water is in the drum i ENGLISH 17 If you deactivate the appliance it is necessary to set the pro gramme again A 9 10 At the end of the programme e The appliance stops automatically e The acoustic signals operate Inthe display 7 comes on e The indicator of the Start Pause but ton JE goes off e The door lock symbol goes off e Press button fi to deactivate the ap pliance After five minutes from the end of the programme the energy saving function automatically deacti vates the appliance When you activate the appliance again the display show the end of the last set programme Turn the programme knob to set a new cycle e Remove the laundry from the appli ance Make sure that the drum is emp ty e Keep the door ajar to prevent mildew and odours e Close the water tap The washing programme is completed but there is water in the drum The drum turns regularly to prevent the creases in the laundry The door stays locked You must drain the water to open the door To drain the water 1 If necessary decrease the spin speed 2 Press the Start Pause button Jj The appliance drain the water and spin 3 When the programme is completed and the door lock symbol goes off you can open the door 4 Deactivate the appliance The appliance drain and spin au tomatically after approximately 18 hours 18 www aeg c
15. EXTRA SP LEN soil Stop with water in 2 max 7 kg the drum AE TSEAREN Synthetica Synthetic or mixed Wash SPIN REDUC 60 Cold fabric items with nor Rinses TION mal level of soil Short spin RINSE HOLD max 3 5 kg FLECKEN EXTRA SP LEN ZEIT SPAREN Synthetica Synthetic or mixed Prewash SPIN REDUC Voorwas fabric items with Wash TION 60 Cold heavy soil Rinses RINSE HOLD max 3 5 kg Short spin EXTRA SP LEN ZEIT SPAREN Strijkvrij gt Synthetic fabric items Wash SPIN REDUC 60 Cold with normal soil Rinses TION max 3 5 kg Short spin RINSE HOLD EXTRA SPULEN ZEIT SPAREN Fijne Was Delicate fabrics as Wash SPIN REDUC 40 Cold acrylics viscose pol Rinses TION yester items with nor Short spin RINSE HOLD mal soil FLECKEN max 3 5 kg EXTRA SPULEN ZEIT SPAREN N Machine washable Wash SPIN REDUC zia wool Hand washable Rinses TION A PE id wool and delicate Short spin RINSE HOLD Ce fabrics with hand washing care sym bol max 2 kg Centrifugeren All fabrics Drainage ofthe SPIN REDUC Pompen4 The maximum load water TION of the laundry is rela Spin phase atthe NO SPIN ted to the type of maximum speed laundry Spoelen All fabrics One rinse with SPIN REDUC additive spin TION phase RINSE HOLD EXTRA SP LEN 12 www aeg com Programme Type of load Cycle Functions Temperature max weight of load description Gordijnen Set this programme Prewash SPIN REDUC 40 Cold to wash curtains It W
16. Refer to Installation Remove the packaging and or the transit bolts Refer to Instal lation Add more laundry in the drum The appliance fills with water and drain immediately The washing re sults are not satis factory The end of the drain hose is too low The detergent you used was not sufficient or cor rect You did not remove the stubborn stains before you wash the laundry Incorrect temperature was set Make sure that the drain hose is in the correct position Increase the detergent quantity or use a different one Use special products to remove the stubborn stains Make sure that you set the cor rect temperature After the check activate the appliance The programme continues from the point of interruption Too much laundry load If the problem occurs again contact the service centre 13 INSTALLATION 13 1 Fixing plate kit 405517114 Available from your authorized dealer Decrease the laundry load If the display shows other alarm codes contact the service centre If you install the appliance on a plinth secure the appliance in the fixing plates Follow the instructions supplied with the kit 26 www aeg com 13 2 Unpacking Use the gloves Remove the external film If necessary use a cutter Remove the cardboard top Remove the polystyrene packaging materials Remove the internal film
17. S Programme Type of load Temperature max weight of load Katoen White and coloured 95 Cold cotton with normal soil max 7 kg Katoen Voor White and coloured was cotton with heavy 95 Cold soil max 7 kg e To activate the function press button and button J at the same time until the display shows the symbol FA e To deactivate the function press but ton and button fj at the same time until the symbol FX goes off You can activate the function e Before you press the Start Pause but ton 9 the appliance cannot start e After you press the Start Pause button EJ all the buttons and the pro gramme knob are deactivated 5 13 Permanent extra rinse function With this function you can keep the extra rinse function permanently on when you set a new programme e To activate the function press button El and button Bj at the same time until the indicator of button is on e To deactivate the function press but ton J and button BJ at the same time until the indicator of button is off Cycle Functions description Wash SPIN REDUC Rinses TION Long spin RINSE HOLD FLECKEN EXTRA SPULEN ZEIT SPAREN Prewash SPIN REDUC Wash TION Rinses RINSE HOLD Long spin EXTRA SP LEN ZEIT SPAREN ENGLISH 11 Programme Type of load Cycle Functions Temperature max weight of load description Extra Stil White and coloured Wash FLECKEN 95 Cold cotton with normal Rinses
18. Use this appliance in a household en vironment e Do not change the specification of this appliance e Obey the safety instructions on the detergent packaging e Do not put flammable products or items that are wet with flammable products in near or on the appliance e Do not touch the glass of the door while a programme operates The glass can be hot e Make sure that you remove all metal objects from the laundry 3 TECHNICAL INFORMATION ENGLISH 5 e Do not put a container to collect pos sible water leakage under the appli ance Contact the Service to ensure which accessories can be used 2 3 Care and Cleaning WARNING Risk of injury or damage to the appliance e Before maintenance deactivate the appliance and disconnect the mains plug from the mains socket e Do not use water spray and steam to clean the appliance e Clean the appliance with a moist soft cloth Only use neutral detergents Do not use abrasive products abrasive cleaning pads solvents or metal ob jects 2 4 Disposal WARNING Risk of injury or suffocation e Disconnect the appliance from the mains supply e Cut off the mains cable and discard it e Remove the door catch to prevent children and pets to get closed in the appliance Dimensions Width Height Depth 600 850 522 mm Total depth 540 mm Electrical connection Voltage 230 V Overall power 2200 W Fuse 10A Frequency 50 Hz Level of protection against ingress of
19. ash TION adds automatically Rinses RINSE HOLD the prewash phase to Short spin EXTRA SPULEN clean the dust from the curtains Do not put the deter gent into the pre wash compartment max 2 5 kg Jeans All items in jeans Wash SPIN REDUC 60 Cold Jersey made items Rinses TION with hi tech materi Short spin RINSE HOLD als EXTRA SPULEN max 3 kg ZEIT SPAREN2 Kort Intensief Quick washing pro Wash SPIN REDUC 60 40 gramme tobe used Rinses TION for lightly soiled Long spin RINSE HOLD white fast coloured EXTRA SPULEN cottons and mixed fabrics max 2 5 kg 20 Min 3 kg Cotton and synthetic Wash SPIN REDUC 40 30 items with light soil Rinses TION or worn only one Short spin time Super Eco Mixed fabrics cotton Wash SPIN REDUC Cold and synthetic items Rinses TION max 3kg Short spin RINSE HOLD EXTRA SPULEN lt __ Katoen White and fast col Wash SPIN REDUC Eco oured cotton with Rinses TION 60 40 normal soil Long spin RINSE HOLD max 7 kg FLECKEN For this programme EXTRA SP LEN you can set only the ZEIT SPAREN Extra Quick duration 1 The STAIN function is not available with a temperature lower than 40 C 2 if you press the button 6 two times Extra Quick duration we recommend that you decrease the quantity of the load It is possible to load fully the appliance however the washing results are reduced 3 The wash and spin phase is soft to prevent the creases of the laundry The appliance
20. ate the appli ance 2 Press button again to activate the appliance Now you can set a new washing programme The appliance does not drain the water 9 6 Change a function You can change only some functions be fore they operate 1 Press button The indicator flashes 2 Change the function set 9 7 Set the delay start 1 Press button RJ again and again un til the display shows the number of minutes or hours The related sym bols comes on 2 Press button the appliance starts the countdown of the delay start When the countdown is completed the programme starts automatically i Before you press button Jj to start the appliance you can can cel or change the set of the delay start 9 8 Cancel the delay start 1 Press button J The related indica tor flashes 2 Press button again and again un til the display shows 0 3 Press button The programme starts 9 9 Open the door While a programme or the delay start operates the appliance door is locked To open the appliance door 1 Press button The door lock symbol in the display goes off 2 Open the appliance door 3 Close the appliance door and press button Jj The programme or the delay start continues i If the temperature and level of the water in the drum are too high the door lock symbol stays on and you cannot open the door To open the door do the steps that follow 1 Deactivate the appliance
21. ce before you do the checks Possible solution The appliance does not fill with water The water tap is closed Open the water tap damaged scale correct The water inlet hose is The filters in the water inlet hose is blocked The water tap is blocked or is furred with lime The connection of the water inlet hose is not Make sure that the water inlet hose has no damages Clean the filters Refer to Care and cleaning Clean the water tap Make sure that the connection is correct too low The water pressure is Contact your local water author ity 24 www aeg com Problem The appliance does not drain the water Possible cause The water drain hose is damaged The filter ofthe drain pump is blocked The connection ofthe water drain hose is not correct A washing programme without the drain phase is set The function Rinse amp Hold is on Possible solution Make sure that the water drain hose has no damages Clean the filter ofthe drain pump Refer to Care and clean ing Make sure that the connection is correct Set the drain programme Set the drain programme The appliance door is open or not closed cor rectly Close the door correctly The anti flood de vice is on The spin phase does not operate The spin phase is off e Disconnect the appliance e Close the water tap e Contact the service ce
22. ion is on amp Delay start ENGLISH 9 The programme time When the programme starts the time decreases with steps of 1 mi nute e The delay start When you press the delay start button the display shows the delay start time e Alarm codes If the appliance has a malfunction the display shows alarm codes Re fer to Troubleshooting chapter e Err The display shows this message for some seconds if You set a function that is not applicable for the programme You change the programme while it operates The indicator of the Start Pause button K flashes S E When the programme is completed 1 Only available for Spin Drain programme 2 The symbols appear on the display when the related phase or function is set 5 4 Start Pause button Press button fi to start or interrupt a programme 5 5 Delay start button Press button JR to delay the start of a programme from 30 minutes to 20 hours 5 6 Time save button Il Press the button J to decrease the programme duration e Press one time to set Shortened dura tion for items with daily soil e Press two times to set Extra Quick for items with almost no soil i 5 7 Extra rinse button Press button J to add rinsing phases to a programme Use this function for persons allergic to detergents and in areas where the water is soft Some programmes accept only one of the two functions 5 8 Stain button El Press button J to
23. ipe must be larger than the external diameter of the drain hose e To a sink spigot Refer to the illustration Put the drain hose in the spigot and tighten it with a clip Make sure that the drain hose makes a loop to prevent that remain ing particles go in the appliance from the sink ENGLISH 31 e Directly to a built in drain pipe in the room wall and tighten it with a clip i You can extend the drain hose to maximum 400 cm Contact the service centre for the other drain hose and the extension 14 ENVIRONMENT CONCERNS Recycle the materials with the appliances Do not dispose symbol amp Put the packaging in appliances marked with the symbol applicable containers to recycle it with the household waste Return the Help protect the environment and product to your local recycling human health and to recycle waste facility or contact your municipal of electrical and electronic office www aeg com shop P Ce es I 132918571 A 142013 C MA HAEG perfekt in form und funktion
24. nser Set and start a programme for cotton at the highest temperature without laundry This removes all possible dirt from the drum and the tub 9 1 Loading the laundry 1 Open the appliance door 2 Put the laundry in the drum one item at a time Shake the items be fore you put them in the appliance Make sure not to put too much laun dry in the drum 3 Close the door Make sure that no laundry stays between the seal and the door There is a risk of water leakage or damage to the laundry ENGLISH 15 9 2 Filling the detergent and additives The detergent compartment for the prewash phase the soak LU programme and for the stain function Add the detergent for prewash soak and stain remover before the start of the programme The detergent compartment for the washing phase If you use a liquid detergent put it immediately before you start the programme i Liquid additives compartment fabric conditioner starch Put the product in the compartment before you start the pro gramme MAX DI This is the maximum level for the quantity of liquid additives Flap for powder or liquid detergent Turn it up or down in the correct position to use powder or liq uid detergent i Always obey the instructions that you find on the packaging of the de tergent products Check the position of the flap 1 Pull out the detergent dispenser un til it st
25. ntre Set the spin programme The filter of the drain pump is blocked Clean the filter of the drain pump Refer to Care and clean ing Balance problems with the laundry load Adjust manually the items in the tub and start the spin phase again The programme does not start The mains plug is not connected in the mains socket Put in the mains plug Blow out fuse in the household fuse box You did not press but ton Qj Replace the fuse Press button i The delay start is set To start immediately the pro gramme cancel the delay start There is water on the floor The Child Lock function is activated Leakages from the cou plings of the water ho ses Deactivate the Child Lock func tion Make sure that the couplings are tight Problem Possible cause Leakages from the drain pump The water drain hose is damaged ENGLISH 25 Possible solution Make sure that the drain pump filter is tight Make sure that the water inlet hose has no damages You cannot open the appliance door The washing pro gramme is in operation Let the washing programme end The appliance makes an unusual noise There is water in the drum Incorrect level of the ap pliance You did not remove the packaging and or the transit bolts The load is very small Set the drain or the spin pro gramme Adjust the level of the appli ance
26. ocedure you must acti vate again the drain system 1 Put 2 litres of water in the main wash compartment of the detergent dis penser 2 Start the programme to drain the water 11 10 Frost precautions If the appliance is installed in an area where the temperature can be less than 0 C remove the remaining water from the inlet hose and the drain pump 1 Disconnect the mains plug from the mains socket 12 TROUBLESHOOTING The start of the appliance does not oc cur or it stops during operation First try to find a solution to the problem refer to the table If not contact the service centre With some problems the acoustic signals operate and the display shows an alarm code Eig The appliance does not fill with water Problem Possible cause ENGLISH 23 2 Close the water tap Remove the water inlet hose hed 4 Put the two ends of the inlet hose in a container and let the water flow out of the hose 5 Empty the drain pump Refer to the emergency drain procedure 6 When the drain pump is empty in stall the inlet hose again IN WARNING Make sure that the temperature is more than 0 C before you use the appliance again The manufacturer is not responsi ble for damages caused by low temperatures e EAE The appliance does not drain the water e EUf The appliance door is open or not closed correctly e EEI The anti flood device is on WARNING Deactivate the applian
27. om 10 HINTS AND TIPS 10 1 The laundry load 10 3 Detergents and additives e Divide the laundry in white coloured synthetics delicates and wool Obey the washing instructions that are on the laundry care labels e Do not wash together white and col oured items e Some coloured items can discolour with the first wash We recommend that you wash them separately for the first times e Button up pillowcases close zippers hooks and poppers Tie up belts e Empty the pockets and unfold the items e Turn inside out multilayered fabrics wool and items with painted illustra tions e Remove hard stains e Wash with a special detergent heavy soil stains e Be careful with the curtains Remove Only use detergents and additives specially made for washing machines Do not mix different types of deter gents To help the environment do not use more than the correct quantity of de tergent Obey the instructions that you find on the on packaging of these products Use the correct products for the type and colour of the fabric the pro gramme temperature and the level of soil If you use liquid detergents do not set the prewash phase If your appliance has not the deter gent dispenser with the flap device add the liquid detergents with a dos ing ball 10 4 Water hardness the hooks or put the curtains in a washing bag or pillowcase e Do not wash in the appliance If the water hardness in your
28. ops 2 Press the lever down to remove the dispenser 16 www aeg com 5 Measure out the detergent and the fabric conditioner 6 Carefully close the detergent dis penser Make sure that the flap does not cause a blockage when you close the drawer 3 4 To use powder detergent turn the flap up To use liquid detergent turn the flap down With the flap in the position DOWN Do not use gelatinous or thick liquid detergents Do not put more liquid deter gent than the limit showed in the flap Do not set the prewash phase Do not set the delay start func tion 9 3 Setting and starting a programme 1 Turn the programme knob The rela ted programme indicator comes on 2 The indicator of button Ej flashes with red colour 3 The display shows the default tem perature and spin speed To change the temperature and or the spin speed press the related buttons 4 Set the available functions The indi cator of the set function comes on or the display shows the related sym bol 5 Press button JJ to start the pro gramme The indicator of button is on The drain pump can operate for a short time when the appliance fills water 9 4 Interrupt a programme 1 Press button The indicator flashes Press button Jj again The washing programme continues 9 5 Cancel a programme 1 Press button to cancel the pro gramme and to deactiv
29. pump can turn If this does not oc cur contact the service centre 22 www aeg com 9 Clean the filter under the water tap and put it back in the pump into the special guides 10 Make sure that you tighten correctly the filter to prevent leakages 11 Put the flap back and close the drain pump door 11 8 The inlet hose filter and The indicator of button JZ flashes and the valve filter the display shows the related alarm Refer to Troubleshooting It could be necessary to clean the filters WARNING when e The appliance does not fill with water e The appliance fills with the water for a long time Disconnect the mains plug from the mains socket To clean the water inlet filters 1 Close the water tap 2 Remove the water inlet hose from the water tap 3 Clean the filter in the inlet hose with a stiff brush 4 Remove the inlet hose behind the appliance 5 Clean the filter in the valve with a stiff brush or a towel 6 Install again the inlet hose Make sure that the couplings are tight to prevent leakages 7 Open the water tap Ko 7 7 11 9 Emergency drain If this occurs do steps 1 through 6 of To clean the drain pump Because of a malfunction the appliance If necessary clean the pump cannot drain the water Put the drainage duct back and close the drain pump flap When you drain the water with the emer gency drain pr
30. y space between the appliance and the carpet Electrical connection WARNING Risk of fire and electrical shock e The appliance must be earthed e Make sure that the electrical informa tion on the rating plate agrees with the power supply If not contact an electrician e Always use a correctly installed shock proof socket e Do not use multi plug adapters and extension cables e Make sure not to cause damage to the mains plug and to the mains cable Should the appliance power supply cable need to be replaced this must be carried out by our Service Centre e Connect the mains plug to the mains socket only at the end of the installa tion Make sure that there is access to the mains plug after the installation e Do not pull the mains cable to discon nect the appliance Always pull the mains plug e Do not touch the mains cable or the mains plug with wet hands e This appliance complies with the E E C Directives Water connection e Make sure not to cause damage to the water hoses e The appliance is to be connected to the water mains using the new sup plied hose sets Old hose sets must not be reused e Before you connect the appliance to new pipes or pipes not used for a long time let the water flow until it is clean e The first time you use the appliance make sure that there is no leakage 2 2 Use WARNING Risk of injury electrical shock fire burns or damage to the ap pliance e
Download Pdf Manuals
Related Search