Masterclock CS5 Lan Network Injector User Manual – v2014.01.16
Contents
1. CE Table of Contents Thank you for your purchase of a CS5 Timecode Network Injector from Masterclock Here you ll find instructions for unpacking and installing your device proper care and configuration We are here to help You can reach us using various contact methods phone email etc found at our website www masterclock com Before calling please attempt to find the answer to your situation here You ll find the answer to most situations here DISCLAIMER The information contained in this document is subject to change without notice Masterclock Inc hereinafter Masterclock or MC makes no warranty of any kind with regard to this material including but not limited to the implied warranties of merchantability and fitness for a particular purpose Masterclock shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing performance or use of this material See important limited warranty information starting on page 18 Introduction cccccccccsseeeccccseeseceeeaeeseecesseeeeeeeseeseeeeesaaaeseesnaaaeeeeees 3 Stallati sorpass R E EE ENS 4 Wiring Solutions ccccccccsseeccesscccsenseecseesecseuscesseneeesaesessaeseees 4 Reset to Factory Default cc ceccccccssseeceeceeseeeeeseeseeeessaeeeeeeees 5 WinDiscovery cccccsecccsescccesccsecccsseccesccsusceseecessusessusessueeesaesenes 5 TEE2. Ok and the assignment will be saved Clear All Device Assignments button This feature allows the end user to clear all associations between all the MASTERCLOCK CS5 LAN INJECTOR s and all the clock displays By clicking Ok all MASTERCLOCK CS5 LAN Injectors and clock displays on the network will have their assignments cleared This is a global clear all In order for a MASTERCLOCK CS5 LAN INJECTOR to regain control of a clock display it will need to go through the Clock Assignment configuration process again CS 5 Encrypted Select for Masterclock proprietary format Packets directed from specific device to specific MDN clocks CS Standard Select for non encrypted directed to IP addresses of independent devices DS gt ADMINISTRATIVE FUNCTIONS AF Click the Administrative Functions button to open a menu that is rarely accessed These include 1 Set Password and 2 Reset Device DS gt AF gt SET PASSWORD Click the Set Password button to create a new password You will need to enter the old password A warning is printed on this window concerning the ramifications of forgetting an appliance password In a worst case scenario you would have to reset the Masterclock CS5 LAN Injector to its factory default settings That reverts back to the factory default password public There is another method to set a password discussed further in this document and describes more fully the rules surro
3. for scope allowed by laws Masterclock CS5 Lan Network Injector User Manual v2014 01 16 CELAB Via Maira snc ke 04100 Latina Kaa LAB Tk he CERTIFICATE OF CONFORMITY Certificate Number UCN 800509446285 Job J10453 Date of Issue 2011 10 17 Certificate valid up to 2014 10 16 Brand Name Masterclock Inc Type COUNTER CONTROLLER RC500 POE Model N COUNTER CONTROLLER RC500 POE Manufacturer Masterclock Inc Address 2484 W Clay St 63301 St Charles MO United States Standard Used EN 55024 1998 A1 A2 EN 55022 2006 A1 2007 Conclusion 18 The product meets the technical requirement of the above standards and the technical requirements of the following directives EMC 2004 108 EC This certificate is only valid for the equipment and configuration described in conjunction with the test data detailed above and with compliance with all applicable legal requirement for the product The CE mark as show below can be used under the responsibility of the manufacturer or the importer after completition of an EC Declaration of Conformity and compliance with all relevant EC Directives prescriptions Copyright of this Certificate is owned by CELAB Italy and may not be reproduced other than in full and with the prior approval of the General Manager Use of this certificate is subjected to Celab regulation available on Celab web site Please check the authenticity of this certificate and related informati
4. 28 47 NTDS26DF 28 49 INTDS26DF 28 48 NTDS46 26 BE 07 kevin lt All MTDS46 14 9E INTDS46 28 45 NTPDS46DF 1D 1F Multicast IP Address as 22 0 0 Port 6168 Communication Timeout seconds 0 15 65535 0 no timeout CS 5 Encrypted CS 5 Standard Configurable Options Firmware Serial Device version Number Network Configuration C55 Injector 1 1 0 12240008 Display Properties Communications Control Clock Control Settings Save Save and Close Time Reference Local Time Settings Administrative Functions Exit Status Administrative Functions accel Set Password Reset Device OO Set To Default Configuration DS gt COMMUNICATIONS CONTROL Certain advanced features may be configured using the Communications Control button This gives access to the Telnet Control window below DS gt CLOCK CONTROL SETTINGS Use this menu to configure which remote MDNXxX displays will respond to the MASTERCLOCK CS5 LAN INJECTOR CS 5 network injector The left column shows the Available Clock The right column shows the clocks Assigned to this Device Use the buttons located in the center to move a device from the Available to the Assigned column Move all available clock displays by pressing All gt and lt All and gt and lt to move individual clock displays When finished click
5. Connection to PC Ethernet communications with MDNXxX display and NASA supplied CS 5 generator 9 28VDC Threaded Universal DC input connector 6 75 x 4 13 x 1 5 inches 17 15 w 10 48 3 81 h in cm 17 3 oz 490 5 grams Masterclock CS5 Lan Network Injector User Manual v2014 01 16 15 Limited Warranty This Masterclock product warranty extends to the original purchaser Masterclock warrants this Masterclock CS5 LAN Injector against defects in materials and workmanship for a period of one year from the date of sale If Masterclock receives notice of such defects during the warranty period Masterclock will at its option either repair or replace products that prove to be defective Should Masterclock be unable to repair or replace the product within a reasonable amount of time the customer s alternate remedy shall be a refund of the purchase price upon return of the product to Masterclock This warranty gives the customer specific legal rights Other rights which vary from state to state or province to province may be available EXCLUSIONS The above warranty shall not apply to defects resulting from improper or inadequate maintenance by the customer customer supplied software or interfacing unauthorized modification or misuse operation outside of the environmental specifications for the product or improper site preparation and maintenance if applicable WARRANTY LIMITATIONS 16 MASTERCLOCK MAKES NO OTHER WARRA
6. User Manual v2014 01 16 Configurable Options Firmware Serial Device version Number Time Reference Network Configuration c55 Injector 1 1 0 12240008 etca Display Properties Communications Control Clock Control Settings Local Time Settings Save fone Save and Close Status Exit Administrative Functions Network Configuration Device Name CS5 INJECTOR 23 68 7 Automatically obtain network configuration from DHCP BOOTP IP address 10 0 100 240 Netmask Gateway 0 0 100 0 0100 7 Click the Discover button to reveal all the devices accessible on the network The status bar will display the count of devices found When complete please wait until 100 appears then disappears a list of device families and groups will be displayed in the left pane of the WinDiscovery window Click the buttons to reveal the individual devices Click the buttons to hide them Each device is configured with a device name from the factory Each device name includes the model name and a MAC address extension You should change the device name to one that can identify the location of the device It is highly recommended that only one user opens WinDiscovery at a time Other methods should not be used to manage the network devices while using this app NETWORK CONFIGURATION The network configuration lower near left may be viewed in summary by clicking the Network Configuratio
7. on hold the button in for 5 seconds or until the led goes dark 3 The unit will go through an initialization process WinDiscovery Installation and Operation Lj a WinDiscovery Included on the CD with your Masterclock CS5 LAN Injector is the WinDiscovery software application for detection configuration and management of all your NTP devices from Masterclock The application operates in the Microsoft Windows OS INSTALLING WINDISCOVERY If you haven t already done so insert the CD that shipped with your Masterclock CS5 LAN Injector to automatically install WinDiscovery If Auto Run is not enabled on your computer 1 Run the setup exe application from the CD 2 By default the setup utility will suggest installing files to C Program Files Masterclock WinDiscovery 3 Click the OK button USING WINDISCOVERY Open WinDiscovery from the Start Menu or by double clicking the shortcut icon on the desktop Device _Intertace 2 CS5 LAN 2B E4 H MCR Reference Generator H MFD Multifunction Display H NTDS Clocks H NTP Clocks H NTP Clocks H RC500 Controller Address When a device is WinDiscovery via USB to the PC the device will appear in blue as Discover Global Password Include discovery for attached Masterclock ALD displays This may significantly increase discovery time 13 39 06 04 26 2013 Masterclock CS5 Lan Network Injector
8. NTY EITHER EXPRESSED OR IMPLIED WITH RESPECT TO THIS PRODUCT MASTERCLOCK SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE In any state or province which does not allow the foregoing disclaimer any implied warranty of merchantability or fitness for a particular purpose imposed by law in those states or provinces is limited to the one year duration of the written warranty EXCLUSIVE REMEDIES THE REMEDIES PROVIDED HEREIN ARE THE CUSTOMER S SOLE AND EXCLUSIVE REMEDIES INNO EVENT SHALL MASTERCLOCK BE LIABLE FOR ANY DIRECT INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES WHETHER BASED ON CONTRACT TORT OR ANY OTHER LEGAL THEORY In any state or province that does not allow the foregoing exclusion or limitation of incidental or consequential damages the customer may have other remedies HARDWARE SERVICE You may return your Masterclock CS5 LAN Injector to Masterclock for repair service Please contact the factory for RETURN AUTHORIZATION before returning the unit When you return your Masterclock CS5 LAN Injector for service you must prepay all shipping charges duty and taxes For international returns please contact the factory Masterclock CS5 Lan Network Injector User Manual v2014 01 16 CELAB Via Maira snc Xk MARS LAB z Fs CERTIFICATE OF CONFORMITY Certificate Number UCN 800509436278 Job J10451 Date of Issue 2011 10 17 Certificate v
9. WORD Set Password Each Masterclock device in your network may have its own Old password password see the Properties window to Set Password New password or you may create a Global Password on the Discover window see below The default password is public New password confirm Your custom password should be one to eleven characters Warning consult your product manual for information on the B ramifications of setting then forgetting an appliance s password and is case sensitive For added password strength you rre A should use both alphanumeric and special ASCII characters ance The password must be entered twice to confirm the entry Click Change Password to save it When a password is set for a device each time you click OK Apply or Apply and Close for that device you will be asked for the password You can select the Remember this password for the session button and you will not be prompted for the password until you restart WinDiscovery Or you can use the Global Password feature see below If you enter the wrong password and selected the Remember this password for the session checkbox you will receive an error upon clicking OK Apply or Apply and Close to any configuration changes You can close the WinDiscovery session to forget the wrong password s However this will require entering the password s again for each device TE Masterclock Inc Ne
10. alid up to 2014 10 16 Brand Name Masterclock Inc Type COUNTER CONTROLLER RC500 AC Model N COUNTER CONTROLLER RC500 AC Manufacturer Masterclock Inc Address 2484 W Clay St 63301 St Charles MO United States Standard Used EN 61000 3 3 2008 EN 61000 3 2 2006 EN 60950 1 2006 EN 55024 1998 A1 A2 EN 55022 2006 A1 2007 Conclusion The product meets the technical requirement of the above standards and the technical requirements of the following directives Low Voltage Directive 2006 95 EC EMC 2004 108 EC This certificate is only valid for the equipment and configuration described in conjunction with the test data detailed above and with compliance with all applicable legal requirement for the product The CE mark as show below can be used under the responsibility of the manufacturer or the importer after completition of an EC Declaration of Conformity and compliance with all relevant EC Directives T adi Copyright of this Certificate is owned by CELAB Italy and may not be reproduced other than in full and with the prior approval of the General Manager Use of this certificate is subjected to Celab regulation available on Celab web site Please check the authenticity of this certificate and related information in the web site w celab com introducing the UCN number in the Check document authenticity area You will see FORY of this certificate and regulation on certificate use This document is released only
11. curity purposes the Telnet configured to use DHCP for network configuration but interface can be disabled When disabled no DHCP BOOTP server is present the RC 500 may not you will no longer be able to access the respond to discovery requests for up to twenty seconds unit with Telnet To re enable the Telnet after power on feature one of the other configuration methods must be used or the unit must Note DHCP is enabled as a factory default be reset to factory default configuration 2 Verify that you have the correct IP address for the unit and the IP address did not change If using DHCP to provide the IP address this address may change periodically you must know the IP address of the unit to use the TELNET interface Masterclock CS5 Lan Network Injector User Manual v2014 01 16 3 Verify that the device does not have the Telnet interface disabled PROBLEM Lost the password POSSIBLE REASONS SOLUTIONS 1 The password cannot be recovered if it is lost Reset the clock to the factory default configuration using the procedure described in the Configuration section After the clock has been reset to factory defaults the unit must be reconfigured 2 The factory default password is public 14 Masterclock CS5 Lan Network Injector User Manual v2014 01 16 MASTERCLOCK CS5 LAN INJECTOR CS 5 Specs SPECIFICATIONS CONNECTORS USB RJ45 POWER Voltage Connector PHYSICAL Size Weight
12. e ee guesphek A A E AE AEE AS 10 Problems Trouble Shooting cccccsccccssesecceseeeeeeeeeeeseneeess 11 Sp cificationS eeepc esi seat sean eee 15 Limited Warranty and Service ccccsssecccessecceesecseeeesseeeess 16 Certificates Of CONFOrMITY cccccceeeecccceeseeeeeceeeeeceseaeeeeeeseaees 17 Contact InformatiOn cccccccsssssseecccecceeeeseeecccessaeeeeeeeceseesaeeees 19 Masterclock CS5 Lan Network Injector User Manual v2014 01 16 Introduction The CS 5 accepts a standard RS 422 CS 5 signal and converts it to UDP network protocol socket 9 28v DC power RJ45 port USB port Ethernet Communication with communications PC via WinDiscovery software RS 422 LAN Steady indicates CS5 RS422 input is present Steady indicates CS5 LAN packets are multicasting on the assigned IP Port Flashing indicates no CS5 RS422 input is present Flashing indicates a network interruption preventing the OFF indicate the network cable is disconnected unit from multicasting OFF indicate the network cable is disconnected Masterclock CS5 Lan Network Injector User Manual v2014 01 16 Network Installation You may install the Masterclock CS5 LAN INJECTOR on your desktop or in a rack mount configuration using the optional Masterclock RM45 Attach power and communication at the back according to these specs For DC power plug in the 9 28v DC cord into its s
13. fell back to a 169 254 xxx xxx address approximately every ten minutes depending upon the Advanced Setting values the Ethernet interface will be reinitialized and the MASTERCLOCK CS5 LAN INJECTOR will attempt to get an IP address from the DHCP sever If the device is successful the error will be cleared and the new address from the DHCP server will be used If a discovery was done using WinDiscovery or Telnet was used this initialization will be delayed by 1 hour PROBLEM MASTERCLOCK CS5 LAN INJECTOR appears to reset periodically POSSIBLE REASONS SOLUTIONS 1 Check the network connection and setup If DHCP is enabled by default and a DHCP server is not active on the network the clock will hesitate periodically while attempting to resolve DHCP configuration To correct the problem switch to manual networking configuration or determine why the local DHCP server is not operating 2 Ifthe device cannot resolve its DHCP mode the unit will periodically perform a soft restart to reinitialize its communication port and DHCP configuration 3 Ifthe MASTERCLOCK CS5 LAN INJECTOR has no valid DNS server or it is down hesitations similar to those described in 1 will occur At least one valid DNS server is required for operation PROBLEM Unable to communicate with the MASTERCLOCK CS5 LAN INJECTOR using Telnet POSSIBLE REASONS SOLUTIONS Telnet can be disabled 1 If the MASTERCLOCK CS5 LAN INJECTOR has been For se
14. ical network as the computer from which you are running WinDiscovery If the computer is separated from the device by a router on a remote network or a firewall it is likely that the router firewall is blocking communications with the device Run WinDiscovery from a computer within the remote network or ask a network system administrator to configure the router firewall in question to pass through both directions UDP broadcasts on port 6163 Note If this does not resolve the detection problems you may additionally configure to pass through both directions UDP broadcasts on ports 6165 6166 and 6364 Some routers will not forward UDP broadcasts across networks currently this capability is required to use WinDiscovery for enterprise level management of Masterclock Inc network appliances If you are running a personal firewall product such as Zone Alarm or Black ICE or the built in Windows firewall you must adjust their configuration to pass through both directions UDP traffic on port 6163 Verify that the hub switch router is capable of supporting the 10MB speed that the attached network device requires Verify that the network device and the computer running WinDiscovery are attached to the network Verify all network cables hubs etc are in proper working order Masterclock CS5 Lan Network Injector User Manual v2014 01 16 1 Devices which have been assigned a fallback IP address of 169 254 xxx xxx will be dis
15. messages are not guaranteed this can cause WinDiscovery to not receive the latest configuration or status packets and thus show outdated or garbled information In some cases it may not be discovered in the WinDiscovery device tree PROBLEM MASTERCLOCK CS5 LAN INJECTOR appears in RED text under WinDiscovery device tree POSSIBLE REASONS SOLUTIONS 1 Incorrect network configuration may be causing the device to receive a fallback IP address and or perform soft restarts Verify that the IP address configured for the device is correct If you manually enter or DHCP assigns an IP address that already exists on the network this will create a conflict The device will reset its address fallback within the local address space Determine the cause of fallback IP address and resolve the issue View the error status under the status window Near the bottom of the status window the error will be displayed 2 When the Ethernet Interface is initialized the network device will verify the IP address either Static or assigned by DHCP is not being used by another device on the network If a conflict is found the device will default to a 169 254 xxx xxx address The IP address that caused the error is saved and returned as an error to WinDiscovery Masterclock CS5 Lan Network Injector User Manual v2014 01 16 This error status is available to the user via the Status window on WinDiscovery 3 If DHCP was selected and the network device
16. n button DEVICE SETTINGS DS The Device Settings window lower left configures the Masterclock CS5 LAN INJECTOR to receive and display in the format that you prefer The top right section of the Device Settings window shows a list of the firmware and options associated with your Masterclock CS5 LAN INJECTOR The rest of the Device Settings window includes access to all configuration options for the network These include display properties and administrative functions such as password There is also a status display to monitor the Masterclock CS5 LAN INJECTOR communication status Any changes made in this window including all the buttons thereon will not be applied until you click the Save button or the Save and Close button prior to clicking the Exit button DS gt NETWORK CONFIGURATION As on the earlier described window the Network Configuration window may be viewed in summary by clicking the Network Configuration selection Masterclock CS5 Lan Network Injector User Manual v2014 01 16 F Communications Control Telnet Control Telnet Control W Allow Telnet Configuration Telnet Port Available Clocks Current Assignment Assigned to this Device Bill s office KEVIN S CUBE MDAIZ9 03 12 Kevin S319 MDN2Z9 03 14 iminei al 5319 imine3al 5319 NTD516 DT 23 2F iNTDS16 DT 28 35 NTDS24 00 DE kevin 9140 NTDS26 12 4D Conf Room NTDS26DF
17. ocket and tighten the locking nut to secure The enclosed CD contains a pdf of this User Manual and discovery communication configuration Microsoft Windows based software called WinDiscovery If you have not already downloaded WinDiscovery for another Masterclock product you should do so now for your Masterclock CS5 LAN Injector On the following page is the preferred wiring diagram for the Masterclock CS5 LAN Injector m CS5 LAN SOLUTION Masterclock CS5 LAN UNIT CS5 ON PIN 7 CS5 ON PINS DC IN 9 28 V SW Computer Required for device configuration system monitoring RS422 CS5 LAN ONLY Ethernet Switch Router USER SUPPLIED SIGNAL SPLITTER CAT5 Ethernet cable RJ45 connectors MDN19 29 49 Multifunctional Digital Display qm RS422 CS5 Gum CAT5 Ethernet cable LAN ONLY aD CATS Ethernet cable LAN RS422 CS5 Masterelock Inc phone USA and Canada 1 800 940 2248 phone international 1 636 724 3666 2484 West Clay Street email sales masterclock com online www masterclock com Saint Charles MO 63301 Masterclock CS5 Lan Network Injector User Manual v2014 01 16 Factory Default Settings RESET CONFIGURATION TO FACTORY DEFAULT In some situations it may be necessary to return the unit to factory default settings To reset to factory default 1 Find the reset button located on the rear of the unit next to the USB port at left 2 While the unit is powered
18. on in the web site v celab com introducing the UCN number in the Check document authenticity area You will see copy of this certificate and regulation on certificate use This document is released only for scope allowed by laws E RAS a AN i N9 B Sot SN O yOs wh i J YL ey o Massimiliano Bertoldi Genera Manager CELAB 1 00 121 Masterclock CS5 Lan Network Injector User Manual v2014 01 16 Contact Us Masterclock Inc 2484 West Clay Street St Charles MO 63301 USA website www masterclock com USA and Canada 1 800 940 2248 1 636 724 3666 1 636 724 3776 fax International 1 636 724 3666 1 636 724 3776 fax Sales sales masterclock com Technical Support i support masterclock com Masterclock Masterclock CS5 Lan Network Injector User Manual v2014 01 16
19. played in the main WinDiscovery window with RED text indicating a problem with the configuration If the configuration of the network device is changed while a 169 254 xxx xxx is being use then the current 169 254 xxx xxx address will become the permanent static address and the original conflicting static address is lost At this point it is necessary to manually change the static IP address to one that will not conflict or you may do a Reset Configuration to restore the system to factory default settings PROBLEM No response to configuration changes under WinDiscovery or garbled characters POSSIBLE REASONS SOLUTIONS 1 The WinDiscovery application has been open for too long and the device s configuration s have changed For the example this can occur if the DHCP server has issued new refreshed addresses Close the WinDiscovery application and restart 2 The discovery process was not complete before selecting device After selecting Discover button wait until the discovery status indicates 100 completion 3 Verify that the physical network cables and equipment and configuration for UDP have not changed 4 Verify that you are currently the only user accessing the device via WinDiscovery or Telnet 5 The network may currently be experiencing heavy traffic which is reducing bandwidth and or causing collisions with the UDP messages packets between the device and WinDiscovery Since delivery of UDP
20. the server with which to connect The factory default port is Telnet server port 23 By default Microsoft Windows 7 has the Telnet Client disabled TO INITIATE A TELNET SESSION IN WINDOWS Select the Run command line interface from the Start menu and enter the command Telnet followed by a space and then the IP address of the unit and click OK TO ENABLE TELNET IN WINDOWS Open the Windows Control Panel click on Programs click on Turn Windows features on or off check V Telnet Client 10 and click OK TO ENABLE TELNET IN LINUX See your system administrator lt 7 Programs and Features I ww Uninstall a program ps Turn Windows features on or off i EL Windows Features Turn Windows features on or off e To turn a feature on select its check box To turn a feature off clear its check box A filled box means that only part of the feature is turned on vib Tablet PC Components W Telnet Server A TFTP Client Masterclock CS5 Lan Network Injector User Manual v2014 01 16 Problems Troubleshooting PROBLEM Unable to discover the MASTERCLOCK CS5 LAN INJECTOR using WinDiscovery POSSIBLE REASONS SOLUTIONS Verify that you have supplied power to the network device The discovery process was not complete After selecting the Discover button wait until the discovery status indicates 100 completion Verify that the MASTERCLOCK CS5 LAN INJECTOR is on the same phys
21. twork Device Discoven Known devices E Masterclock Inc CRL Bell Ringer Device Interface Address Masterclock Inc MCR El MCR1000 Device MCR5000 Device MCR5000 15 32 MCR5000 23 C0 You can also remove the incorrect password entry during a WinDiscovery session by going to the drop down menu for the device right click to see this and selecting the Forget memorized password button Masterclock Inc NTDS Clocks Masterclock Inc NTP Clocks Unknown Device Id 0 CLKNTD12 NTD26 H NTD44 Masterclock Inc RC500 Discover Ext Global Parone p ee eve GLOBAL PASSWORD nd The Global Password button at left on the Network Device Discovery window allows the user to enter a single Global Password mm i i password once for all NTP devices During subsequent wien wi abied the clobal password is used for sessions you will not have to reenter the password Windiscovery comunications with network devices Make sure all devices have the same password before enabling fiero cessor Cancel ENABLING DISABLING GLOBAL PASSWORD IV Enable Global Password To enable the Global Password Enter Global Password 1 Check Enable Global Password C UUA 2 Type your password 3 Click OK The Global Password being used must match To disable the Global Password the password on all the devices being 1 De select the Enable Global Pass
22. unding password usage Masterclock CS5 Lan Network Injector User Manual v2014 01 16 DS gt STATUS E sha anes on CO At the bottom left of the Masterclock CS5 LAN Injector eee Network Configuration C5 Injector 1 1 0 12240008 window is the Status button The Masterclock CS5 LAN siete Duplay Poetics Injector window includes a Display Snapshot of a graphic Communications Central digital clock representing the face of the actual Masterclock Clock Control Settings CS5 LAN Injector in real time Local Time Settings Save Save and Close iia ine Network Tab includes the name of the device the model of the device and a summary of the network configuration much of this data is repeated from the network configuration window described earlier Decoding Multicasting Network Name CSS INJECTOR 23 B8 Model C55 Network Injector Network Configuration Ethernet 00 21 32 01 23 B8 IP 10 0 100 240 Netmask 255 255 252 0 Gateway 10 0 100 1 DNS 10 0 100 7 DHCP Enabled CS5 INJECTOR 23 B8 Status Display snapshot eats n Network Name CSS INJECTOR 23 B8 Model C55 Network Injector m Network Configuration Ethernet 00 21 32 01 23 B8 IP 10 0 100 240 Netmask 255 255 252 0 Gateway 10 0 100 1 DNS 10 0 100 7 Enabled Masterclock CS5 Lan Network Injector User Manual v2014 01 16 lee SET PASS
23. word checkbox administered On any new system being installed the factory default global password is 2 Click OK public Masterclock CS5 Lan Network Injector User Manual v2014 01 16 Telnet Configuration via Telnet may not be convenient for devices operating with a factory default configuration since the IP address is not known Use the WinDiscovery application to establish first time networking configuration For security purposes the Telnet interface can be disabled When disabled you will no longer be able to access the device with Telnet To re enable the Telnet feature one of the other configuration methods must be used or the clock must be reset to factory default If you are not familiar with Telnet ask your network administrator for assistance Type the name of a program folder document or Internet resource and Windows will open it for you Open telnet 10 0 100 120 x Cancel Browse Control Panel Home System and Security Network and Internet Hardware and Sound Programs User Accounts and Family a Ep A RN S ERT RC I O Y N T G A gt Control Pa gt Programs Search Control Panel Pl Those with Linux and other non Windows operating systems will not be able to use WinDiscovery For Windows and non Windows users alike a terminal style configuration interface is available via Telnet to specify the IP address of the clock as
Download Pdf Manuals
Related Search