SBS-01V
Contents
1. the ESC on the wires that are connected to the battery by soldering them and then protecting them with heat shrink The manual for the Telemetry system should be referred to after the setup is complete checking to make sure it functions as desired and that it provides the correct voltage on the display FUTABA CORPORATION 1080 Yabutsuka Chosei mura Chosei gun Chiba ken 299 4395 Japan Phone 81 475 32 6982 Facsimile 81 475 32 6983 7 FUTABA CORPORATION 2012 10 12. Futaba Voltage sensor SBS 01V Instruction Manual 1M23N26714 Thank you for purchasing Futaba s SBS 01V Voltage Sensor This sensor used in conjunction with a telemetry enabled transmitter receiver is used to indicate the voltage of the item to which it is attached Although the telemetry receiver of Futaba s has a function which measures voltage if SBS 01V is used it can measure more battery voltage To maximize your enjoyment and to ensure proper sensing please read through this manual thoroughly We also encourage you to retain the manual for future reference should the need arise to EXT Battery EXT Line s ca Fuse mount in either direction Heat Shrink Tube EED Indication Red Nosignal reception Green Red When setting up the slot Green Red Unrecoverable error Alternate blink Slot Number Setup SBS 01V uses two continuous slots Please note that the proper default start slot for this accessory is number 6 When setup changing or adding it is the following numbers that are made to a start slot 1 2 3 4 5 6 8 9 10 11 12 13 14 16 17 18 19 20 21 22 24 25 26 27 28 29 30 Information on how to change the slot assignment is included in the transmitter s manual What is measured is total voltage when the battery which you want to measure has two or more cells One cell of a battery with many cells cannot be measured Don t carry out connection wiring at one cell If it co
3. could result in damage to the cable receiver etc Always mount the cable in accordance with the instructions included in this manual Normal Line Allow a slight amount of slack in the cable E If necessary fasten this cable at a suitable location to prevent any damage from vibration during flight O Turn on the receiver prior to connecting the Extra Voltage Input To prevent any short circuits please ensure that the cable is routed away from any condu cive materials Don t apply voltage higher than 100V to Ex tra voltage line E There is fear of explosion ignition and breakage It is cautious of the burn and fire in wiring work enough O The work of wiring must not connect a bat tery E The example of wiring Two drive batteries are measured R7008SB use Drive battery 1 EXT Battery to S BUS2 Drive battery 2 EXT Battery mea Futaba El EXT Line Normal Line Receiver battery R7008SB Battery voltage measurement for receivers R7008SB use The drive battery 1 is measured in an EXT port R7008SB use The drive battery 2 is measured in an EXT line SBS 01V use Two drive batteries and power supplies for servos are measured R7008SB use SBS 01V measures two voltage One corresponds to high voltages such as a drive battery with an EXT line Another is a normal line and is measurement of the battery for receivers of a line connected to 3P connector or th
4. e battery for servos Drive battery 1 7 EXT Battery to S BUS2 EXT Line Normal Line Drive battery 2 EXT Battery Futaba H t Power supplies ci Another power for servos S BUS2 servos supply Hub R7008SB Switch Receiver battery Battery voltage measurement for receivers R7008SB use The drive battery 1 is measured in an EXT port R7008SB use The drive battery 2 is measured in an EXT line SBS 01V use The voltage for servos is measured in a power supply line SBS 01V use 2 Cut approximately 30mm of the negative black line from the cable Solder the fuse inline on the negative wire and then reattach the section of wire that was previously removed The fuse should be attached as close to the external power supply as possible Solder welding The fuse should be attached as close to the eh external power supply as possible Zh E x Fuse to Black line Fuse mount in either direction Place a piece of heat shrink tubing over the fuse ensuring that it covers the soldered areas Shrink the tubing snug to the fuse and the wire using a heat gun P Heat shrink tube 4 va Heat shrink Heat shrink tube The cable should be connected as shown in the diagram below The cable _ gets connected to the wires that come off the ESC and connect to the battery 0 ee eee motor s controller To Motor To Power Battery The connection is affixed to
5. nnects with one cell there is fear of ignition The SBS 01V is designed for use with Futaba telemetry systems Features Measures receiver battery voltage and the voltage of a second battery or power supply External Line Range 0 100V s Normal Line Range 3 5 8 4V s Weight 0 20z 6 0g Length 34 25in 870mm SBS 01V SBS Ol1V Futaba M LED 3P Connector to S BUS2 port A WARNING Failure to follow these safety precautions may result in severe injury to yourself and others To utilize the SBS 01V altitude sensor connect it to the S BUS2 port of the Futaba telemetry enabled receivers E The SBS 01V will not function properly if connected to an S BUS port or other channel ports Ensure that the unit is connected properly to the receiver Failure to do so could result in damage to the sensor Ensure that the unit is mounted in an area that will eliminate exposure to fuel water and vibration E As with any electronic components proper precautions are urged to prolong the life and increase the performance of the SBS 01V To ensure that the SBS 01V is functioning as desired please test accordingly E Do not fly until inspection is complete Do not use the SBS 01V with anything other than an R C model In order to prevent any short circuits please observe the polarity of all connections E Ensure that the unit is connected properly failure to do so
Download Pdf Manuals
Related Search
SBS 01V sbs-01v sbs 01 obrazac sbs 01a sbs01 sbs019 sbs016s sbs01/lec