Manual
Contents
1. eo PRODUCT OVERVIEW 25 PRODUCT FEATURES 6 PACKING LIST 7 ONE CHANNEL MEDIA CONVERTER PHYSICAL PORTS Port STATUS LEDs INSTALLATION 9 SELECTING A SITE FOR THE EQUIPMENT 9 CONNECTING TO POWER cescceeeseesseeereneneneneeeneneceseeeeteneee 9 INSTALLING INA 5 8 9 SPECIFICATIONS isscnsoscosassestenensadnodgevcntudentasvesssteasusestassesserensnenrsncsesssbestase 10 ORDERING INFORMATION csssssssscsssssscssscesssessscesssnssessssssssesssssseseseeeees 11 APPENDIX ssssssvsssensssssensssnsvsesssessunesenchsvasssutusessedscbassossnseseascvevassosvesesbesvess 11 User s Manual Gigabit Ethernet Media Converter Introduction The Gigabit Ethernet Media Converter provides one channel for media conversion between 1000Base T and 1000Base SX LX with link fault pass through function It can be used as a stand alone device or with a standard 19 chassis as shown below Product Overview Figure 1 1000Base T to Gigabit SFP socket Media Converter with link fault pass through function lt NOTE gt The chassis is to be ordered separately User s Manual 5 Gigabit Ethernet Media Converter Product Features e One channel media conversion between 1000Base T and 1000Base SX LX e socket for Gigabit fiber optic expansion e Fiber media allows either Multi mode fiber Single mode fiber or WDM Single mode fiber Full wire speed forwarding rate Front panel2. 0Base LX SMF of 1300nm 9 or 10 125um SFP 10km 1000Base LX SMF of 1300nm 9 or 10 125um SFP 20km 1000Base LX SMF of 1550nm 9 or 10 125um SFP 50km 1000Base LX WDM SMF of TX 1310nm RX 1550nm 9 10 125um SFP 20km 1000Base LX WDM SMF of TX 1550nm RX 1310nm 9 10 125um SFP 20km 1000Base LX WDM SMF of TX 1310nm RX 1550nm 9 10 125um SFP 40km 1000Base LX WDM SMF of TX 1550nm RX 1310nm 9 10 125um SFP 40km lt NOTE gt The maximum node to node network distance is in full duplex operation MMF denotes Multi Mode Fiber SMF denotes Single Mode Fiber MMF can be applied for 1000Base LX as well Appendix Fiber budget Distance 1000Base SX 7 5dBm 220m 850nm 62 5 125 1000Base SX 7 5dBm 550m 850nm 50 125um 1000Base LX 14dBm 10km 1300nm 9 10 125um 1000Base LX 19dBm 20km 1300nm 9 10 125um 1000Base LX 19dBm 50km 1550nm 9 or 10 125um 1000Base LX 12dBm 20km TX 1310nm RX 1550nm 9 10 125um 1000Base LX 12dBm 20km TX 1550nm RX 1310nm 9 10 125um 1000Base LX 20dBm 40km TX 1310nm RX 1550nm 9 or 10 125um 1000Base LX 20dBm 40km TX 1550nm RX 1310nm 9 10 125um User s Manual 11
3. Gigabit Ethernet Media Converter Quick Start Guide This quick start guide describes how to install and use the Gigabit Ethernet media converter The converter introduced here provides one channel media conversion solution Physical Description Product Overview This Gigabit Ethernet media converter is a plug and play device Connect the supplied AC to DC power adaptor to the receptacle on the rear panel of the Gigabit Ethernet media converter and then attach the plug into a standard AC outlet with a voltage range from 100 to 240V AC DIP Switch DIP Up Default Setting Down switch Left hand The fiber port auto detects Force the fiber port to full side duplex mode duplex mode Right hand Disable LFPT Enable LFPT LFPT side link fault pass through function The 1000Base T and 1000Base SX LX Connectors The 1000Base T Connections Ss The following lists the pinouts of 1000Base T port 3 The 1000Base SX LX Connections The SFP socket for Gigabit fiber optic expansion User s Manual 1 Gigabit Ethernet Media Converter The Port Status LEDs LEDs State Indication Power Steady Power feeding in Off No power LNKC Steady TX port A valid network connection established LNKC stands for LINK Copper Off No connection LNKF Steady FX port A valid network connection established LNKF stands for LINK Fiber Off No connection FDX COL Steady Conn
4. ation instructions for the Converter Selecting a Site for the Equipment As with any electric device you should place the equipment where it will not be subjected to extreme temperatures humidity or electromagnetic interference Specifically the site you select should meet the following requirements e The ambient temperature should be between 32 and 113 degrees Fahrenheit 0 to 45 degrees Celsius e The relative humidity should be less than 95 percent non condensing e Surrounding electrical devices should not exceed the electromagnetic field RFC standards for IEC 801 3 Level 2 3V M field strength Make sure that the equipment receives adequate ventilation Do not block the ventilation holes of the equipment e The power outlet should be within 1 8 meters of the product Connecting to Power This Converter is a plug and play device e Connect the supplied AC to DC power adapter to the receptacle at the back of the converter e Attach the plug into a standard AC outlet Installing in a Chassis The Converter is designed to fit into any of the expansion slots on a rackmount chassis e Unscrew the carrier from the desired expansion slot on the chassis Fitthe converter onto the carrier e When the converter is completely seated onto the carrier insert the carrier to the guide rails of the expansion slot e Carefully slide in the carrier until it is fully and firmly fit the chassis e Fasten the carrier to the chass
5. ection in full duplex mode FDX stands for FULL DUPLEX RX Steady Receiving data Off No reception TX Steady Transmitting data Off No transmission Functional Description DIP switch configuration for Link Fault Pass Through fiber auto force mode 1000Mbps Auto Full duplex Auto Negotiation Auto MDI MDIX SFP socket for Gigabit fiber optic expansion Full wire speed forwarding rate 0 8A 12VDC external universal PSU 0 to 45 C 32 F to 113 F operating temperature range Aluminum case Supports Wall Mounting installation or use with media converter chassis system User s Manual Gigabit Ethernet Media Converter FCC Statement The FCC Federal Communications Commission restricts the amount of radio frequency emission and radiation coming from computer equipment The equipment introduced in this manual has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user is required to correct the inte
6. is by the screws NOTE Never insert any converter into the chassis directly without using the supplied carriers The carriers allow secure and consistent placement of the converters into the chassis backplane without causing any damage User s Manual 9 Gigabit Ethernet Media Converter Specifications Applicable Standards IEEE 802 3ab 1000Base T IEEE 802 3z 1000Base SX LX Fixed Ports 1000Base T to 1000Base SX LX 1 TX port 1 Gigabit SFP socket Speed 2000Mbps for full duplex Forwarding rate 1 488 100pps for 1000Mbps LED Indicators 1000T to 1000SX LX Power TX RX FDX COL LNKF LNKC Dimensions 80 3mm W x 109 2mm D x 23 8mm H 3 16 W x 4 3 D x 0 94 H Weight 150g 0 33lb Power External power adaptor 0 2A 12VDC Power Consumption 2 4W Max Operating Temperature 0 45 C 32 F 113 F Storage Temperature 10 C 70 C 14 F 158 F Humidity 5 95 non condensing Emissions FCC part 15 Class A CE Mark Class A 10 Manual User s Gigabit Ethernet Media Converter Ordering Information 1000T to 1000SX LX Media Converter Gigabit Ethernet Cable Connector Distance Port One 1000Base T 4 pairs Cat 5 RJ 45 100m Port Two Options 1000Base SX MMF of 850nm 62 5 125 SFP 220m 1000Base SX MMF of 850nm 50 125um SFP 550m 100
7. lease inspect the contents and report any apparent damage or missing items immediately to your authorized reseller The Media Converter e User s Manual e AC to DC Power Adaptor User s Manual 7 Gigabit Ethernet Media Converter One Channel Media Converter Physical Ports 1000T to 1000SX LX Media Converter This converter provides one TX port and one Gigabit SFP socket For the Gigabit SFP socket it provides options of multi mode single mode or WDM single mode fiber For the TX port it uses RJ 45 connector and supports auto MDIX for uplink purpose Port Status LEDs The LED indicators give you instant feedback on status of the converter LNKF PWR LNKC soll Im o TX FDX 10008 5 7 DCi2V coL 1 Figure 2 1000Base T to Gigabit SFP socket Media Converter with link fault pass through function LEDs State Indication Power Steady Power feeding in Off No power LNKC Steady TX port A valid network connection established LNKC stands for LINK Copper No connection LNKF Steady FX port A valid network connection established LNKF stands for LINK Fiber Off No connection FDX COL Steady Connection in full duplex mode FDX stands for FULL DUPLEX RX Steady Receiving data Off No reception TX Steady Transmitting data Off No transmission 8 User s Manual Gigabit Ethernet Media Converter Installation This chapter gives step by step install
8. rference at his her own expense Any changes or modifications not expressly approved by the manufacture would void the user s authority to operate the equipment Trademarks Product names mentioned in this manual may be trademarks or registered trademarks of those products All trademarks or brand names mentioned are properties of their respective companies Preface This manual describes how to install and use the Gigabit Ethernet Media Converter The Converter introduced here provides one channel media conversion solution 1000Base T to 1000Base SX LX multi mode single mode with link fault pass through function 1000Base T to 1000Base LX WDM single mode with link fault pass through function The Gigabit Ethernet Media Converter fully complies with IEEESO2 3ab 1000Base T and IEEE802 3z 1000Base SX LX Gigabit Ethernet standards In this manual you will find Product overview Features on the media converter Illustrative LED functions Installation instructions Specifications User s Manual 3 Gigabit Ethernet Media Converter Table of Contents QUICK START GUIDE PHYSICAL DESCRIPTION FUNCTIONAL DESCRIPTION cessere 2 FCC STATEMENT wisesesssssessenesssessssosensutestasvocstscdsoaessacbevseneasoevsieseosensessassen 3 TRADEMARES aisits tiaia i 3 PREFACE TABLE OF CONTENTS wisssessesssssssscsosensussssasvocsononsnasssasvocseseasoessanseosensensassse 4 INTRODUCTION
9. status LEDs Used as a stand alone device or with a chassis Hot swappable when used with a chassis Make sure to make a connection to the TX port before make a connection to the fiber port a link condition will be sensed on the fiber port whenever the media converter detects a link condition on the TX port There are two pins on the DIP switch of the 1000Base T and 1000Base SX LX one channel media converter gt Toggle up the pin on the left hand side to let the fiber port auto detect duplex mode gt Toggle down the pin on the left hand side to force the fiber port to full duplex mode gt Toggle up the on the right hand side to disable the link fault pass through function gt Toggle down the on the right hand side to enable the link fault pass through function DIP Up Default Setting Down switch Left hand The fiber port auto Force the fiber port to full side detects duplex mode duplex mode Right hand Disable LFPT Enable LFPT LFPT side link fault pass through function e fiber port should be forced to full duplex mode when two 1000Base T and 1000Base SX LX one channel media converters are connected to each other via fiber port e The TX port auto detects duplex mode e The TX port supports auto MDIX for uplink purpose 6 User s Manual Gigabit Ethernet Media Converter Packing List When you unpack this product package you will find the items listed below P
Download Pdf Manuals
Related Search