AirLive WL-5460APv2_e9 User`s Manual
Contents
1. O Disable Wireless Check the box to disable the Wireless LAN Interface by so doing you won t be LAN Interface Channel Number Wireless Client Isolation able to make wireless connection with this Access Point in the network you are located In other words this device will not be visible by any wireless station You can choose one mode of the following you need 2 4GHz B 802 11b supported rate only 2 4GHz G 802 11g supported rate only 2 4GHz B G 802 11b supported rate and 802 119 supported rate The default is 2 4GHz B G mode The SSID differentiates one WLAN from another therefore all access points and all devices attempting to connect to a specific WLAN must use the same SSID It is case sensitive and must not exceed 32 characters A device will not be permitted to join the BSS unless it can provide the unique SSID An SSID is also referred to as a network name because essentially it is a name that identifies a wireless network The number of channels supported depends on the region of this Access Point All stations communicating with the Access Point must use the same channel When enabled the wireless clients are separated from each other Please refer the AP mode settings gt Wireless Client Isolation for details 31 WL5460AP v2 User s Manual Security Please refer the AP mode settings gt Security for details This setting is use between Wireless client and this device Wireless2. C WDS Repeater Setup WDS Repeater C Universal Repeater setup Universal Repeater WISP Setup WISP PEEEREE C WISP Universal Repeater Setup WISP Universal Repeater 11 WL5460AP v2 User s Manual WDS Repeater Mode A repeater s function is to extend the wireless coverage of another wireless AP or router For WDS repeater to work the remote wireless AP Router must also support WDS function WW DR WR WR WR WWW AAA B WDS Wireless Router WDS Repeater To set the operation mode to WDS Repeater Please go to Mode gt WDS Repeater and click the button for configuration WLAN Access Point Mode Status TCP IP Reboot Other Kei tw A www ovislink com be Wireless Mode CAP Setup Access Point C Client Setup Client Infrastructure Client Ad Hoc Bridge Setup Bridge e WDS Repeater Setup WG Repeater C Universal Repeater Setup Universal Repeater C WISP Setup WISP Setup C WISP Universal Repeater Setup WISP Universal Repeater 12 WL5460AP v2 User s Manual Universal Repeater Mode A universal repeater can also extend the wireless coverage of another wireless AP or router But the universal repeater does not require the remote device to have WDS function Therefore it can work with almost any wireless device Note When you are using the universal repeater mode please make sure the remote AP Router s WDS function is turned off EOI CREO PEE SG vi kl
3. Methods of measurement Product standard to demonstrate the Compliance of radio base stations and Fixed terminal stations for wireless Telecommunication System with the Basic restrictions or the reference levels related to human exposure to radio Frequency electromagnetic fields 110 MHz 40 GHz General public Safety for information technology equipment including electrical business equipment C 0560 Manufacturer Importer Albert Yeh Vice President Date 2007 4 18 Stamp WL 5450 5460 AP CE Declaration Statement OvisLink Corp timto prohlaSuje Ze tento Siuo OvisLink Corp deklaruoja kad Cesky Czech WL 5450 5460 AP je ve shod se z kladn mi Lietuvi SisWL 5450 5460 AP atitinka esminius reikalavimus po adavky a dal mi p slu n mi ustanoven mi Lithuanian ir kitas 1999 5 EB Direktyvos nuostatas sm rnice 1999 5 ES Undertegnede OvisLink Corp erkl rer herved at ni Hierbij verklaart OvisLink Corp dat het toestel Dansk Danish f lgende udstyr WL 5450 5460 APoverholder de Nederlands Dutch WL 5450 5460 AP in overeenstemming is met de v sentlige krav og vrige relevante krav i direktiv essenti le eisen en de andere relevante bepalingen 1999 5 EF van richtlijn 1999 5 EG Hiermit erkl rt OvisLink Corp dass sich das Hawnhekk OvisLink Corp jiddikjara li dan Ger t WL 5450 5460 APin bereinstimmung mit Malti Maltese WL 5450 5460 AP jikkonforma mal ti ijiet den grundlegenden
4. Su e Le sy ELV Dd Com B sy A TT Router Universal Repeater To set the operation mode to Universal Repeater Please go to Mode Universal Repeater and click the button for configuration A Li e WLAN Access Point 4 Mode Status TCP IP Reboot Other OvisLink Coi 5 www orisliink com tw A Wireless Mode C WISP Setup WISP C AP Setup Access Point C Client Setup Client Infrastructure Client Ad Hoc C Bridge Setup Bridge C WDS Repeater Setup WDS Repeater e Universal Repeater Setup Universal Repeater Seen Boop C WISP Universal Repeater Setup WISP Universal Repeater 13 WL5460AP v2 User s Manual WISP Client Router Mode WISP Client Router mode In WISP mode the AP will behave just the same as the Client mode for wireless function However Router functions are added between the wireless WAN side and the Ethernet LAN side Therefore The WISP subscriber can share the WISP connection without the need for extra router WISP FF PO Dutdoor AF Ez Client Router M7 To set the operation mode to WISP Please go to Mode gt WISP and click the button for configuration WLAN Access Point j Mode Status TCP IP Reboot Other www ovislink com tw te E Wireless Mode Ge C AP Setup Access Point C Client Setup Client Infrastructure Client Ad Hoc Bridge Setup Bridge C WDS Repeater Setup WDS Repeater C Universal
5. and your password for entering the configuration WEB UI Log system Log This page can be used to set remote log server and show the system log LC Enable Log System all Wireless only Apply Changes 47 WL5460AP v2 User s Manual This function can list all log information about device Enable Log Enabled or Disabled display system log information List system all log information List wireless log information only Refresh log information Clear all information in window NTP Time Zone Setting Current Time Year Month Day Hr Mlin Sec la C Enable NTP client update Time Zone Select GMT 08 00 Taipei se NTP server a Ol Manual IP Setting This function can setting system time from local computer or Internet Enable NTP client update Enable or Disable setting system from Internet NTP Server Reset Reset system time configurayion Refresh Refresh system time information 48 WL5460AP v2 User s Manual Appendix A Emergency Code Should firmware upgrade fail WL 5460AP will enter Emergency Mode Please do the following instructions for firmware recovery 1 Open the internet protocol dialogue and set IP address at http 192 168 1 X Internet Protocol TCP 1P Properties oe Ax General fou can get F settings assigned automatically if your network supports thie capability Otherwise pou need to ask pour network administrator hor the appropriate IP settings Obta
6. 14 WISE UNIVERSAL REPEATER MODE qa 15 EE ee 16 A eee mR PRER tic Nee A ORO cna Ta OEE a ER tc ODO rae em De eae ee RR 17 AE le een Ne 18 EE 19 EIER EE 23 CENT MODE SETTING 21 BRIDGE MODE SETIN EE 29 ME EPEA REENEN 31 UNIVERSAL REPEATER MODE SETTING a ata as 33 WISP CLINT ROUTER MODF SET TIN Gri a a ets 35 WISP H UNIVERSAL REPEATER MODE SETTING eege r 38 KR 40 TORIR E 43 EEN 45 Eeer 46 APPENDIX A nds 49 WL5460AP v2 User s Manual Introduction WL 5460APv2 is world s most popular multi function access point lt features an impressive total of 7 wireless multi function modes that are not available in normal access point In addition the ACK timeout and RSSI feature makes it suitable for long distance application From ordinary AP application to Hotspot and WISP usage you will find the WL 5460AP is the device you want WL 5460APv2 is an IEEE802 11b g compliant 11 Mbps 54 Mbps Ethernet Wireless Access Point The Wireless Access Point is equipped with two 10 100 M Auto sensing Ethernet ports for connecting to LAN and also for cascading to next Wireless Access Point WL 5460APv2 provides 64 128bit WEP encryption WPA PSK WPA2 PSK and IEEE802 1x which ensures a high level of security to protect users data and privacy The MAC Address filter prevents the unauthorized MAC Addresses from accessing your Wireless LAN Your network security is therefore double assured The web based management utility is provided for easy con
7. Client Ad Hoc Please go to Mode gt Client and click the button In the Network Type field select as infrastructure for configuration WLAN Access Point Mode Status TCP IP Reboot Other Client Mode Settings Alias Name Wireless_AP Disable Wireless LAN Interface Band 2 4 GHz B Network Type Infrastructure ae infrastructure ES SSID PES site Survey Channel Number Auto Mac Clone Single Ethernet Client a Clone foooooonconco Security setup Advanced Settings setup Apply Changes Reset 10 WL5460AP v2 User s Manual Bridge Mode In this mode 2 access points in two remote locations connect to each other to provide a wireless bridge between 2 remote LANs It is mostly used by enterprise to connect 2 remote office s network together The bridge modes are connected by using either the WDS Wireless Distribution System or Ad Hoc topology This feature is also useful when users want to bridge networks between buildings where it is impossible to deploy network cable connections between these buildings To set the operation mode to Bridge Please go to Mode Bridge and click the button for configuration WLAN Access Point Status TCP IP Reboot werw orialink com tw AL Y Wireless Mode A A ayer A EEN ue page 1s Used io erent CAP Setup Access Point C Client Setup Client Infrastructure Client Ad Hoc Bridge Setup Bridge
8. E www ovialinlccom tw gt WISP Universal Repeater Mode Settings Alias Name Wireless_AP C Disable Wireless LAN Interface Band 2 4 GHz B 5 SSID lairlive SSID of Extended Interface Clone MAC Address poooao000000 Enable Encryption On Both WAN and WLAN side e F Site Survey Security Advanced Settings Wan Port Virtual Server Special Application DMZ Remote Management Setup You can set the alias name for this device limited not exceed 32 characters able to make wireless connection with this Access Point in the network you are located In other words this device will not be visible by any wireless station You can choose one mode of the following you need 2 4GHz B 802 11b supported rate only 2 4GHz G 802 11g supported rate only 2 4GHz B G 802 11b supported rate and 802 11g supported rate The default is 2 4GHz B G mode The SSID differentiates one WLAN from another therefore all access points and all devices attempting to connect to a specific WLAN must use the same SSID In WISP mode you have to enter the WISP Outdoor AP SSID manually or click the site survey button to connect and get SSID automatically SSID of extended Please refer the Universal repeater mode settings gt SSID of extended Interface Interface for details MAC Clone Address Enter the MAC Address of Single Ethernet Client 38 WL5460AP v2 User s Manual E
9. G 802 11b supported rate and 802 119 supported rate The default is 2 4GHz B G mode The SSID differentiates one WLAN from another therefore all access points and all devices attempting to connect to a specific WLAN must use the same SSID In WISP mode you have to enter the WISP Outdoor AP SSID manually or click the site survey button to connect and get SSID automatically Site Survey Please refer the Client mode settings Site Survey for details MAC Clone Address Enter the MAC Address of Single Ethernet Client Security Please refer the AP mode settings gt Security Survey for details Not supported with RADIUS 802 1x authentication 35 WL5460AP v2 User s Manual Advance Setting Please refer the AP mode settings gt Advance Setting for details WAN Port Configuration WAN port Virtual Server Special Application WAN Access Type DNS 1 DNS 2 DNS 3 Clone MAC Address Save Reset DHCP Client D Attain DNS Automatically C Set DNS Manually 000000000000 Respond to WAN Ping Enable UPnP Enable IPsec pass through on WPN connection Enable PPTP pass through on YPN connection Enable L2TP pass through on VPN connection au AKAK You can select many WAN Access Type Static IP DHCP Client PPPOE PPTP and L2TP for WAN connection depend on you WISP provided Virtual Servers Servers Local IP Address Protocol Port Range Description Current
10. Repeater setup Universal Repeater WISP Setup WISP C WISP Universal Repeater Setup WISP Universal Repeater 14 WL5460AP v2 User s Manual WISP Universal Repeater Mode In this mode the AP behaves virtually the same as the WISP mode except one thing the AP can also send wireless signal to the LAN side That means the AP can connect with the remote WISP AP and the indoor wireless card and then provide IP sharing capability all at the same time However the output power is divided between 2 wireless sides and proper antenna installation can influence the performance greatly WISP Outdoor AP WISP Universal To set the operation mode to WISP Universal Repeater Please go to Mode gt WISP Universal Repeater and click the button for configuration WLAN Access Point Mode Status TCP IP Reboot Other werw ovislink com tea vO Wireless Mode This page ls Used to Ee AP Setup Access Point Client Setup Client Infrastructure Client Ad Hoc C Bridge Setup Bridge C WDS Repeater Setup WOS Repeater Universal Repeater SEHH Universal Repeater WISP Setup WISP GG WISP Universal Repeater Setup WISP Universal Repeater 15 WL5460AP v2 User s Manual fe S pa ri et A duh Usel ira tie fe 1 Start your computer Connect an Ethernet cable between your computer and the Wireless Access Point 2 Make sure your wired station is set to the same sub
11. SS PS et Encryption 802 1x 802 1x RADIUS security You can select None WEP WPA TKIP WPA AES WPA2 AES WPA2 Mixed method for data encryption Encryption None No data encryption and Use 802 1x Authentication is disable Encryption 802 1x Authentication is enabled and the RADIUS Server will proceed to check the 802 1x Authentication and make the RADIUS server to issue the WEP key dynamically You can select WEP 64bits or WEP 128bits for data encryption Encryption WPA TKIP WPA AES WPA RADIUS authentication use WPA Wi Fi Protect Access data encryption for 802 1x authentication 22 WL5460AP v2 User s Manual WPA is an encryption standard proposed by WiFi for advance protection by utilizing a password key TKIP or certificate It is more secure than WEP encryption Encryption WPA2 AES WPA2 Mixed The two most important features beyond WPA to become standardized through 802 11i WPA2 are pre authentication which enables secure fast roaming without noticeable signal latency Pre authentication provides a way to establish a PMK security association before a client associates The advantage Is that the client reduces the time that it s disconnected to the network Authentication RADIUS Enter the RADIUS Server IP address and Password provided by your ISP Port Enter the RADIUS Server s port number provided by your ISP The default is 1812 IP Address Enter the RADIUS Server s IP Address pr
12. Virtual Servers Table Local IP ort Address Range Enable Virtual Servers Reset Protocol Description Select Delete All Delete Selected Reset In WISP mode you can setup and enable Virtual server function Like Web FTP Email DNS Telnet server Select one virtual server type and enter the Local IP address Local Port Range and click the save button Special Applications Incoming Type Port Incoming Start Incoming End Trigger Trigger End Port Type Port Enable Dialpad O Patak BOTH y BOTH BOTH y UDP 8 You can enable some system default special application 36 a KI xI LTTE m E E tf Ke 4 like Qucktime 4 WL5460AP v2 User s Manual Audio Video application Dialpad internet phone service or define the special application manually select the incoming type TCP UDP Incoming start End port Trigger Start End port Select the Trigger Type IT Enable DMZ DMZ Host IP Address Reset Enable DMZ and enter the DMZ Host IP address Remote Management Remote Management Y Enable Web Server Access via WAN Port Number lao Save Reset Enable the function that setting configuration from Internet 37 WL5460AP v2 User s Manual WISP Universal Repeater Mode Setting SE DER L WLAN Access Point ive L 4 Mode Status TCP IP Reboot Other OvisLink Corp
13. 000 In this page you can change the TCP IP settings of this Access Point select to enable disable the DHCP Client 802 1d Spanning Tree and Clone MAC Address IP Address This field can be modified only when DHCP Client is disabled If your system manager assigned you static IP settings then you will have to enter the information provided Subnet Mask Enter the information provided by your system manager Default Gateway Enter the information provided by your system manager Select Disable Client or Server from the pull down menu Disable Select to disable DHCP server function Client Select to automatically get the LAN port IP address from ISP For ADSL Cable Modem Server Select to enable DHCP server function DHCP Client Range WL 5060AP IP addresses continuing from 192 168 100 1 to 192 168 100 253 Show Client Click to show Active DHCP Client table DNS Server Enter the Domain Name Service IP address 802 1d Spanning Tree To enable 802 1d Spanning Tree will prevent the network from infinite loops Infinite loop will happen in the network when WDS is enabled and there are multiple active paths between stations 43 WL5460AP v2 User s Manual Clone MAC Address You can specify the MAC address of your Access Point to replace the factory setting 44 WL5460AP v2 User s Manual Click the button to restart device Air Live WAN Access Point om k Mode Status TCP IP Reboo
14. 02 119 supported rate only 2 4GHz B G 802 11b supported rate and 802 119 supported rate The default is 2 4GHz B G mode Network Type Client mode have two Network type Infrastructure A wireless network that is built around one or more access points providing wireless clients access to wired LAN or Internet service It is the most popular WLAN network structure today AdHoc wireless network do not use wireless AP orrouter as the central hub of the network Instead wireless client are connected directly to each other The SSID differentiates one WLAN from another therefore all access points and all devices attempting to connect to a specific WLAN must use the same SSID It is case sensitive and must not exceed 32 characters A device will not be permitted to join the BSS unless it can provide the unique SSID An SSID is also referred to 27 WL5460AP v2 User s Manual as a network name because essentially it is a name that identifies a wireless network Site Survey Wireless Site Survey ative DE h B 0 AP nae ar wlan 00 20 e0 39 a1 bb 3 B AP WEP 26 default 00 c0 02 fe 43 68 40 B G AP na 16 PLANET 00 18 87 11 43 d6 11 B G AP WEP 15 Connect Site survey displays all the active Access Points and IBSS in the neighborhood You can select one AP to associate Press Site Survey button to search the wireless device that this client want to connect Channel Number Allow user to s
15. 66 100 252 Network Mask 255 255 255 0 Nefanlt Gatewaw 192168 100 254 system Data System Uptime Oday shiz As Firmware Version S4bOAP ei Wireless Mode AR Physical Address 00 46 0d cb 55 Band 2 4 GHz Bra SSID airlive Channel Number 13 Encryption Disabled Associated Clients O BSSID 00 42 0d cb 55 LAN Configuration Connection Method Fixed IF Physical Address 00 4 62 0d cb 54 IP Address 192 160 100 252 Network Mask 255 255 255 0 Nefault Gatewaw 197 168 100 254 40 WL5460AP v2 User s Manual Uptime The time period since the device was up Firmware Version The current version of the firmware installed in this device Wireless There are 7 modes supported The default mode is Access Point If you want to change to other mode please click the Mode and select the wireless mode you want Display wireless MAC address information Display wireless band type information Display the SSID of this device The number of channels supported depends on the region of this Access Point All stations communicating with the Access Point must use the same channel Display encryption setting information Displays the total number of clients associated to this AP You can have up to 64 clients to associate to this Access Point BSSID displays the ID of current BSS which uniquely identifies each BSS In AP mode this value is the MAC address of this Access Point LAN Configuration TCP IP Connection Method D
16. Anforderungen und den essenzjali u ma provvedimenti o rajn relevanti li brigen einschl gigen Bestimmungen der hemm fid Dirrettiva 1999 5 EC Richtlinie 1999 5 EG befindet Kaesolevaga kinnitab OvisLink Corp seadme Alul rott OvisLink Corp nyilatkozom hogy a Eesti Estonian WL 5450 5460 AP vastavust direktiivi 1999 5 EU Magyar WL 5450 5460 AP megfelel a vonatkozo alapveto pohinduetele ja nimetatud direktiivist tulenevatele Hungarian kovetelm nyeknek s az 1999 5 EC iranyelv egy b teistele asjakohastele satetele eldirasainak Hereby OvisLink Corp declares that this Niniejszym OvisLink Corp o wiadcza ze WL 5450 5460 AP is in compliance with the Polski Polish WL 5450 5460 AP jest zgodny z zasadniczymi essential requirements and other relevant wymogami oraz pozosta ymi stosownymi provisions of Directive 1999 5 EC postanowieniami Dyrektywy 1999 5 EC Por medio de la presente OvisLink Corp declara ipt OvisLink Corp declara que este que el WL 5450 5460 APcumple con los Portugu s WL 5450 5460 APest conforme com os requisitos requisitos esenciales y cualesquiera otras Portuguese essenciais e outras disposi es da Directiva disposiciones aplicables o exigibles de la 1999 5 CE Directiva 1999 5 CE ME THN MNAPOY2A OvisLink Corp AHAQNEI OvisLink Corp izjavlja da je ta WL 5450 5460 AP v EAAnvikn Greek OTIWL 5450 5460 AP YMMOPOQNETAI Slovensko skladu z bistvenimi zahtevami in ostalimi relevantnimi NPO2 TIX OY2I0AEl2 ANAITH2EI2 KAI
17. DNS server address automatically Use the following DNS server addresses Preferred DNS server b Alternate DNS server 6 Open WEB browser Enter the IP address http 192 168 100 252 to login to the paid menu ELA v2 Microsoft Internet Explorer EECH Qes O h A GD Osea Zi rege Sien El e E E Air Live p SC OvisLink Corp www ovislink com tw K WLAN Access Point Mode Status TCP IP Reboot Other Thank you for using WLAN Access Point ET oo Wien 50 WL5460AP v2 User s Manual
18. Security Setup Encryption None _ ee Apply Chay ep WDS Security Please refer to the Bridge mode settings gt WDS Security for details This setting is use between both wireless AP Router devices WDS Security Setup Encryption WEP Key Format WEP Key Pre Shared Key Format Pre Shared Key Apply Changes Close Reset Advance Setting Please refer the AP mode settings gt Advance Setting for details Access Control Please refer the AP mode setting gt Access Control for details AP MAC Address Enter 12 digits in hex numbers in the AP MAC address BSSID field and press the Add MAC Address Button to associate with other s Wireless access point Before you want to use bridge mode to connect each other to provide A wireless bridge between 2 remote LANs you need add the BSSID of other s wireless AP first Delete Selected To delete bridge from access to this Access Point you may firstly check the Select Delete All To delete all the clients from access to this Access Point just press Delete All 32 WL5460AP v2 User s Manual Universal Repeater Mode Setting ir Liwe WLAN Access Point E F 4 Mode Status TCP IP Reboot Other OvisLink Corp h WW orina Le E Universal Repeater Mode Settings Alias Name Wireless _AF Disable Wireless LAN Interface Band 2 4 GHz B G SSID lairlive Channel Number 13 Wireless Client Isolation Disabled D SSID of Extended Interf
19. TI2 Slovenian dolocili direktive 1999 5 ES AOINE 2XETIKE2 AIATA EIZ TH OAHTIAZ 1999 5 EK fr Par la pr sente OvisLink Corp d clare que sk OvisLink Corp t mto vyhlasuje Ze WL 5450 5460 AP Francais French l appareil WL 5450 5460 AP est conforme aux Slovensky Slovak spi a z kladn po iadavky a v etky pr slu n exigences essentielles et aux autres dispositions ustanovenia Smernice 1999 5 ES pertinentes de la directive 1999 5 CE Con la presente OvisLink Corp dichiara che OvisLink Corp vakuuttaa t ten ett Italiano Italian questo WL 5450 5460 AP conforme ai requisiti Suomi Finnish WL 5450 5460 AP tyyppinen laite on direktiivin essenziali ed alle altre disposizioni pertinenti 1999 5 EY oleellisten vaatimusten ja sita koskevien stabilite dalla direttiva 1999 5 CE direktiivin muiden ehtojen mukainen Ar o OvisLink Corp deklar ka H r me l sir OvisLink Corp yfir v a WL 5450 5460 AP atbilst Direkt vas 1999 5 EK_ slenska Icelandic WL 5450 5460 AP er samr mi vi grunnkr fur og b tiskaj m pras b m un citiem ar to saist tajiem a rar kr fur sem ger ar eru tilskipun 1999 5 EC noteikumiem H rmed intygar OvisLink Corp att denna OvisLink Corp erkl rer herved at utstyret WL 5450 5460 AP st r verensst mmelse med Norsk Norwegian WL 5450 5460 AP er i samsvar med de de v sentliga egenskapskrav och vriga grunnleggende krav og vrige relevante krav i relevanta best mmelser som fra
20. WPA2 PSK Mixed 802 1 RADIUS To provide a certain level of security the IEEE 802 11 standard has defined two types of authentication methods Open System or Shared Key And WL 5460APv2 also support other wireless authentication and encryption methods for enhance your wireless network With Open System authentication a wireless PC can join any network and receive any messages that are not encrypted With Shared Key authentication only those PCs that possess the correct authentication key can join the network By default IEEE 802 11 wireless devices operate in an Open System network and None data encryption If you want secure your wireless network you need to setup wireless security related function to enable security network Encryption Encryption is set to None by default If the Access Point is using Encryption None then the wireless adapter will need to be set to the same authentication mode Wireless Security Setup Encryption None gl Apply Changes Reset Encryption If selected WEP encryption you must set WEP key value 19 WL5460AP v2 User s Manual Wireless Security Setup Encryption WEP Authentication Type Key Length Key Format Hex 10 characters Default Tx Key Key ls Encryption Key 1 Encryption Key Encryption Key 3 Encryption Key 4 Apply Changes Reset You can select Open System or Shared Key type for authentication You can set 64bit or 128bit Encryption Se
21. ace 302 1d Spanning Tree Disabled D Security Advanced Settings setup Access Control Setup Apply Changes Alias Name You can set the alias name for this device limited not exceed 32 characters O Disable Wireless Check the box to disable the Wireless LAN Interface by so doing you won t be Site Surrey setup LAN Interface able to make wireless connection with this Access Point in the network you are located In other words this device will not be visible by any wireless station You can choose one mode of the following you need 2 4GHz B 802 11b supported rate only 2 4GHz G 802 11g supported rate only 2 4GHz B G 802 11b supported rate and 802 11g supported rate The default is 2 4GHz B G mode The SSID differentiates one WLAN from another therefore all access points and all devices attempting to connect to a specific WLAN must use the same SSID It is case sensitive and must not exceed 32 characters A device will not be permitted to join the BSS unless it can provide the unique SSID An SSID is also referred to as a network name because essentially it is a name that identifies a wireless network Channel Number The number of channels supported depends on the region of this Access Point All stations communicating with the Access Point must use the same channel SSID of extended When in Universal Repeater mode you have to enter the ESSID of other s Interface AP Router that device w
22. ant to connect The device SSID and the SSID of extended interface can be the same or different 33 WL5460AP v2 User s Manual When you are using the universal repeater mode please make sure the remote AP Router WDS function is turned off Please refer the Bridge mode settings gt Site Survey for details Please refer the AP mode settings gt Security for details This setting used Wireless client or remote AP to link this device Advance Setting Please refer the AP mode settings gt Advance Setting for details Access Control Please refer the AP mode setting gt Access Control for details 34 WL5460AP v2 User s Manual WISP Client Router Mode Setting Air Live WLAN Access Point Status TCP IP Reboot OvisLink Corp wwwevislink com tw 5 WISP Mode Settings Alias Name Wireless_AP Disable Wireless LAN Interface Band 2 4 GHz B SSID airlive Site Survey Clone MAC Address 000000000000 Security Setup Advanced Settings Setup Wan Port Setup Virtual Server Setup Special Application Setup DMZ Setup Remote Management Setup Apply Changes Reset able to make wireless connection with this Access Point in the network you are located In other words this device will not be visible by any wireless station You can choose one mode of the following you need 2 4GHz B 802 11b supported rate only 2 4GHz G 802 119 supported rate only 2 4GHz B
23. d of providing a remedy This value should remain at its default setting of 2347 Should you encounter inconsistent data flow only minor modifications of this value are recommended Beacon Interval Beacon Interval is the amount of time between beacon transmissions Before a station enters power save mode the station needs the beacon interval to know when to wake up to receive the beacon and learn whether there are buffered frames at the access point Data Rate By default the unit adaptively selects the highest possible rate for transmission Select the basic rates to be used among the following options Auto 1 2 5 5 110r 54 Mbps For most networks the default setting is Auto which is the best choice When Auto is enabled the transmission rate will 24 WL5460AP v2 User s Manual select the optimal rate If obstacles or interference are present the system will automatically fall back to a lower rate Preamble Type A preamble is a signal used in wireless environment to synchronize the transmitting timing including Synchronization and Start frame delimiter In a noisy network environment the Preamble Type should be set to Long Preamble The Short Preamble is intended for applications where minimum overhead and maximum performance is desired If in a noisy network environment the performance will be decreased Select enabled to allow all the wireless stations to detect the SSID of this Access Point IAPP Inte
24. e Click if you want to load a pre saved file enter the file name with the correct path and then click on Upload or click to select the file 46 WL5460AP v2 User s Manual Save in fet Desktop D e e ES Look in Fes Desktop D e El e ES N My Documents ES My Documents A My Computer E t my Computer to My Network Places History GE My Network Places al config e File name contie Save File name Open My Network P Ca My Network P L ze Save as type dat Document y Cancel Files of type all Files DI Cancel te E Reset Settings to Default Click button to restore the default configuration Password Password Setup Confirmed Password For secure reason lt is recommended that you set the account to access the web server of this Access Point Leaving the password blank will disable the protection The login screen prompts immediately once you finish setting password Remember your password for you will be asked to enter them every time you access the web server of this Access Point New Password Set your new password Password can be up to 30 characters long Password can contain letter number and space It is case sensitive Confirm Password Re enter the new password for confirmation Note when you setup the password and click the apply change button system will pop up Window and ask the username and password Please enter system default username admin not changeable
25. et the channel manually or automatically If set channel manually just select the channel you want to specify If Auto is selected user can set the channel range to have Wireless Access Point automatically survey and choose the channel with best situation for communication All stations communicating with the Access Point must use the same channel when setup infrastructure of Client mode the channel number can not Be changed You have to go to AP mode to change the channel number Auto MAC Clone Check the box to enable MAC Clone for Single Ethernet Client Manual MAC Clone Enter the MAC Address of Single Ethernet Client Address Security Please refer the AP mode settings gt Security for details In client mode are not supported with RADIUS 802 1x authentication Wireless Security Setup Encryption WPA PSK TKIP D Dre Shared Pre Shared Group Key Apply Changes Reset Advance Setting Please refer the AP mode settings gt Advance Setting for details 28 WL5460AP v2 User s Manual Bridge Mode Setting e KEE WLAN Access Point Mode Status TCP IP Reboot Other OvisLink Corp a Bridge Mode Settings Alias Hame Wireless AP Disable Wireless LAN Interface Band 2 4 GHz BH5 T Channel Number 13 802 1d Spanning Tree Disabled gt WDS Security Setup Advanced Settings Apply Changes able to make wireless connection with this Access Point in the network
26. figuration that your wireless network connection is ensured to be always solid and hassle free 1 WL5460AP v2 User s Manual E e E mN em A e e e FP H Pp A pr Ul wey Ex a 2x100Mbps LAN ports for Wireless AP cascade 2MB flash 16MB SDRAM 18dBm output Power AP Client Bridge WDS Repeater Universal Repeater mode WISP Client Router WISP Universal Repeater mode Allows WEP 64 128 bit Support WPA PSK WPA2 PSK encryption Support data rate automatic fallback Automatic channel selection Allowable channels 1 11 USA FCC 1 13 Europe ETSI Client access control Supports 802 1x Radius client with EAP TLS TKIP AES encryption Supports IAPP Adjustable Tx power Tx rate and SSID broadcast ACK Timeout Watch dog function Web interface management Support System event log and statistics MAC filtering For wireless only 2 WL5460AP v2 User s Manual Parts Names and Functions 1 Front Panel LED Indicators 5460AP 5460AP v2 WL 5460AP Power Status LinkiAct WEPAYPA MAC Ctrl Bridge LAN1 LAN2 Repeater 00C LED Status Indicator Green Turns solid green when power is N A applied to this device Turns solid red when the device is booting after boot successfully the light turn off 3 6 Wireless Green Turns solid green when connected Receiving Link Act and associated to at least a client Sending data station WEP WPA O
27. idden Node problem Hidden Node is a situation in which two stations are within range of the same Access Point but are not within range of each other Therefore they are hidden nodes for each other When a station starts data transmission with the Access Point it might not notice that the other station is already using the wireless medium When these two stations send data at the same time they might collide when arriving simultaneously at the Access Point The collision will most certainly result in a loss of messages for both stations Thus the RTS Threshold mechanism provides a solution to prevent data collisions When you enable RTS Threshold on a suspect hidden Station this station and its Access Point will use a Request to Send RTS The station will send an RTS to the Access Point informing that it is going to transmit the data Upon receipt the Access Point will respond with a CTS message to all station within its range to notify all other stations to defer transmission It will also confirm the requestor station that the Access Point has reserved it for the time frame of the requested transmission If the Hidden Node problem is an issue please specify the packet size The RTS mechanism will be activated if the data size exceeds the value you set The default value is 2347 Warning Enabling RTS Threshold will cause redundant network overhead that could negatively affect the throughput performance instea
28. in an IP address automatically f Use the following IP address IP address 192 168 1 100 Subnet mask 255 255 255 Default gateway d i Obtain DHS server address automatically Ce Use the following DNS server addresses Preferred DNS server l l Alternate DHS server Advanced 2 Open WEB broswer and enter the IP address http 192 168 1 6 to enter Emergency Mode setup page We detected your system had been crashed Please upload your Image file again System Upgrade Browse UPGRADE 3 Click the button to find and open the firmware file We detected your system had been crashed Please upload your Image file again System Upgrade Fawr253_54604Pv2e8 bin Browse UPGRADE 4 Click UPGRADE button to start upgrade firmware Wait for about 35 to 40 seconds for the firmware upgrade to complete Upload OK Please wait 49 WL5460AP v2 User s Manual 5 Reopen the internet protocol dialogue Set IP address at http 192 168 100 X Internet Protocol TCP IP Properties E 2 xi General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address IP address 192 168 100 100 Subnet mask 255 255 ee 0 ee Obtain
29. ince last time you press Apply Change Delete Selected To delete clients from access to this Access Point you may firstly check the Select checkbox next to the MAC address and Comments and press Delete Selected Delete All To delete all the clients from access to this Access Point just press Delete All without selecting the checkbox Reset If you have made any selection press Reset will clear all the select mark 26 WL5460AP v2 User s Manual Client Mode Setting WLAN Access Point Status TCP IP Reboot HN e Client Mode Settings Sly ey a ep ro ee Ps page 1s Used io setup different s WES mode Alias H ame Di reles s AP Disable Wireless LAN Interface Band 2 4 GHz Drais Network Type Infrastructure Infrastructure Ad hoc SSID site Survey Channel Number Auto Mac Clone Single Ethernet Client Manual MAC Clone Agocooooodco Address Security Setup Advanced Settings Setup Apply Changes Alias Name You can set the alias name for this device limited not exceed 32 characters O Disable Wireless Check the box to disable the Wireless LAN Interface by so doing you won t be LAN Interface able to make wireless connection with this Access Point in the network you are located In other words this device will not be visible by any wireless station You can choose one mode of the following you need 2 4GHz B 802 11b supported rate only 2 4GHz G 8
30. isplay the connection method you can setup in TCP IP section Display the internet connection method you can setup in WISP mode gt WAN Port configuration Display the AP MAC address information Display the internet IP Address you can setup in WISP mode gt WAN Port configuration Display the network mask you can setup in WISP mode gt WAN Port configuration Display the default gateway you can setup in WISP mode gt WAN Port configuration 41 WL5460AP v2 User s Manual Statistics Statistics Sent Packets 1380 Wireless L4N Received Packets 5679 Sent Packets Ethernet L4N Received Packets see E Ethernet WAN Recelwved Packets Received Packets 4858 Refresh The Statistics table shows the packets sent received over wireless and ethernet LAN respectively Active Clients Active Wireless Client Table MAC Address 7 Tx Packet EE Rx Packet 8 Tx Rate Mbps E Power Saving None Refresh Display the active Wireless Clients information include wireless MAC address TX Rx Packet TX Rate and Power Saving information 42 WL5460AP v2 User s Manual WLAN Access Point Mode Status TCP IP Reboot Other OvisLink i i wwwovislink com twoy a LAN Interface Setup E IP Address 192 168 100 262 Subnet Mask 255 255 255 0 Default Gateway 0 0 0 0 DHCP Client Range 192 168 100 100 192 168 100 200 DNS Server Clone MAC Address 000000000
31. lect ASCII if you are using ASCII characters case sensitive Select HEX if you are using hexadecimal numbers 0 9 or A F 10 hexadecimal digits or 5 ASCII characters are needed if 64 bit WEP is used 26 hexadecimal digits or 13 ASCII characters are needed if 128 bit WEP is used Shared Key is used when both the sender and the recipient share a secret key So you can choose Open system or one Shared Key authentication method WPA PSK Encryption WPA PSK TKIP or WPA PSK AES Wi Fi Protected Access WPA with Pre Shared Key PSK provides better security than WEP keys It does not require a RADIUS server in order to provide association authentication but you do have to enter a shared key for the authentication purpose The encryption key is generated automatically and dynamically Wireless Security Setup Encryption MIRA Pre Shared Key Format Passphrase y Pre Shared Key Po Group Key Life Time B6400 sec Apply Changes Reset 20 WL5460AP v2 User s Manual Wireless Security Setup Encryption s el Leg Pre Shared Key Format Passphrase gt Pre Shared Key Group Key Life Time B6400 sec Apply Changes Reset Encryption You can select WPA PSK TKIP or WPA PSK AES method for data mm fee Pre shared Key There are two formats for choice to set the Pre shared key i e Passphrase and Hex If Hex is selected users will have to enter a 64 characters string For easier the Passphrase at least 8 charac
32. ly optimize the throughput over long distance links This is especially true for 802 11a and 802 11g networks You can set as default for auto adjustment Press to save the new settings on the screen Press to discard the data you have entered since last time you press Apply Change Access Control Press the setup button for detail configurations 25 WL5460AP v2 User s Manual Wireless Access Control Wireless Access Control Mode Disable MAC Address Comment Apply Changes Reset Current Access Control List MAC Address Comment Select Delete All Reset When Enable Wireless Access Control is checked only those clients whose wireless MAC addresses listed in the access control list can access this Access Point If the list contains no entries with this function being enabled then no clients will be able to access this Access Point Wireless Access Control Select the Access Control Mode from the pull down menu Disable Select to disable Wireless Access Control Mode Allow Listed Only the stations shown in the table can associate with the AP Deny Listed Stations shown in the table won t be able to associate with the AP MAC Address Enter the MAC Address of a station that is allowed to access this Access Point Comment You may enter up to 20 characters as a remark to the previous MAC Address Apply Changes Press to save the new settings on the screen Press to discard the data you have entered s
33. mg r av direktiv direktiv 1999 5 EF 1999 5 EG A copy of the full CE report can be obtained from the following address OvisLink Corp 5F No 6 Lane 130 Min Chuan Rd Hsin Tien City Taipei Taiwan R O C This equipment may be used in AT BE CY CZ DK EE FI FR DE GR HU IE IT LV LT LU MT NL PL PT SK SI ES SE GB IS LI NO CH BG RO TR FCC Certifications This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician fo
34. nable Encryption On Kai Enable Encryption On Both WAN and WLAN side security SLAM side only Advanced Settings WAN side onl You can designate security to use for WLAN side WAN side or both sides Both WAN and WLAN side The security is used on both the WISP and the Wireless Client PC side connection WLAN side only The security used on wireless client connection only The WISP side is not encrypted WAN side only The security used on WISP connection only The WLAN side is not encrypted Security Please refer the AP mode settings gt Security Survey for details a WAN por Remote Management Please refer the WISP mode settings gt Remote Management Setting for details 39 WL5460AP v2 User s Manual In this screen you can see the current settings and status of this Access Point You can change settings by selecting specific tab described in below T Live WLAN Access Point TCP IP Reboot Other OvisLink Corp System Statistics A ww ovisiink com tw EL MEF L System Data ai eee a ed E E PES page SOS ine i current sta Wie System Af the SC Uptime Oday 3h 24m 49s Firmware Version 54604 Pv2_ eb Wireless Mode AP Physical Address OO 47 62 00 cb 55 Band 2 4 GHz B G SSID airlive Channel Number 13 Encryption Disabled Associated Clients O BSSID OO 4f62 0d cb 55 LAN Configuration Connection Method Fixed IF Physical Address OU 4f62 0d ch 54 IP Address 192 1
35. net as the Wireless Access Point Le 192 168 100 X 3 Start your WEB browser In the Address box enter the following s WL S460AP v2 Microsoft Internet Explorer File Edit view Favorites Tools Help Q Back 7 x Ej A 8 Search Favorites a Media Li 2 Address E http 192 168 100 252 home asp pes 4 The configuration menu is divided into five categories Mode Status TCP IP Reboot and Other Click on the desired setup item to expand the page in the main navigation page The setup pages covered in this utility are described below AirL ive WLAN Access Point U Mode Status TCP IP Reboot Other OvisLink Corp A wew ovislink com tw ta A Thank you for using WLAN Access Point 16 WL5460AP v2 User s Manual You can choose and setup different wireless mode for detail configurations Ser gee WLAN Access Point CT Mode Status TCP IP Reboot Other OvisLink LN a wwwovislink comi twas r system Statistics Active Clients Wireless Mode WISP Setup WISP GG AP Setup Access Point C Client Setup Client Infrastructure Client Ad Hoc C Bridge Setup Bridge C WDS Repeater Setup WOS Repeater C Universal Repeater Setup Universal Repeater _ Setup _ Setup C WISP Universal Repeater Setup WISP Universal Repeater Wireless Mode J AP Select the AP and press Setup button for Wireless AP mode configuration Client Select the Client and press Setup bu
36. omputer so that the computer can send packets from wired end to wireless interface Refer to the illustration below This station AP1 plus the connected computer 1 can associate to another Access Point AP2 and then can have the Internet access if the other Access Point AP2 has the Internet connection Client Mode Infrastructure To set the operation mode to Client Infrastructure Please go to Mode gt Client and click the button In the Network Type field select as infrastructure for configuration Se Live WLAN Access Point D 4 Mode Status TCP IP Reboot Other OvisLink E gt werwievislink com trae 3 Wireless Mode The rnana de o PS page La vsed to erent AP Setup Access Point Client Setup Client Infrastructure Client Ad Hoc Bridge Setup Bridge C WDS Repeater Setup WDS Repeater Universal Repeater Setup Universal Repeater WISP Setup WISP Eeun C WISP Universal Repeater Setup WISP Universal Repeater NO WL5460AP v2 User s Manual Client Mode Ad hoc If set to the Client Ad hoc mode this device can work like a wireless station when it is connected to a computer so that the computer can send packets from wired end to wireless interface You can share files and printers between wireless stations PC and laptop with wireless network adapter installed See the sample application below Client Moc To set the operation mode to
37. ovided by your ISP Password Enter the password that the AP shares with the RADIUS Server Accounting RADIUS Enter the Accounting RADIUS Server IP address and Password provided by your Server ISP Advanced Settings Press the setup button for detail configurations Wireless Advanced Settings Fragment Threshold baus 256 2346 RTS Threshold Du 02347 Beacon Interval ho O 20 1024 ms Inactivity Time 50000 100 50480000 ms Data Rate Auto y Preamble Type Long Preamble Short Preamble Broadcast SSID Enabled Disabled IAPP Enabled Disabled 802 11g Protection Enabled Disabled Tx Power Level Default About 18dB Enable WatchDog Watch Interval fi 1 60 minutes Watch Host 0 U 455 U Auto adjustment Unit 4usec set Default Ack timeout Apply Changes Reset lt is not recommended that settings in this page to be changed unless advanced users want to change to meet their wireless environment for optimal performance Fragment Threshold Fragmentation mechanism is used for improving the efficiency when high traffic flows along in the wireless network If your 802 11g Wireless LAN PC Card often transmit large files in wireless 23 WL5460AP v2 User s Manual network you can enter new Fragment Threshold value to split the packet The value can be set from 256 to 2346 The default value is 2346 RTS Threshold RTS Threshold is a mechanism implemented to prevent the H
38. pped with configuration that is functional right out of the box If you want to change the settings in order to perform more advanced configuration or even change the mode of operation you can use the web based utility provided by the manufacturer as described in the following sections 7 WL5460AP v2 User s Manual Access Point Mode When acting as an access point default setting this device connects all the stations PC notebook with wireless network adapter to a wired network All stations can have the Internet access if only the Access Point has the Internet connection See the sample application below Access Pc ADSL Cable Modem Internet To set the operation mode to Access Point please go to Mode gt AP and click the button Ti Live WLAN Access Point 4 Mode Status TCP IP Reboot Other system Statistics Active Clients OvisLink Corp wwwovislink com fe d Wireless Mode Bi ite A ES ae CS fue page is Used to ent EE AP Setup Access Point C Client Setup Client Infrastructure Client Ad Hor C Bridge Setup Bridge C WDS Repeater Setup WOS Repeater C Universal Repeater Setup Universal Repeater C WISP Setup WISP PEEELEE C WISP Universal Repeater Setup WISP Universal Repeater 00 WL5460AP v2 User s Manual Client Mode Infrastructure If set to Client Infrastructure mode this device can work like a wireless station when it s connected to a c
39. r Access Point Protocol is designed for the enforcement of unique association throughout a ESS Extended Service Set and a secure exchange of station s security context between current access point AP and new AP during handoff period 802 119 Protection The 802 11g standard includes a protection mechanism to ensure mixed 802 11b and 802 11g operation If there is no such kind of mechanism exists the two kinds of standards may mutually interfere and decrease network s performance TX Power Level Apply Change For countries that impose limit on WLAN output power it might be necessary to reduce TX transmit power There are 7 TX Power Levels to choose from select a level to make sure that the output power measured at the antenna end will not exceed the legal limit in your country Enable Watch dog Check and enable this watch dog function Watch Interval Setup the interval time for watch dog function between 1 to 60 mins Watch Host Enter the watch dog host ip address ACK Timeout When a packet is sent out from one wireless station to the other it will waits for an Acknowledgement frame from the remote station If the ACK is NOT received within that timeout period then the packet will be re transmitted resulting in reduced throughput If the ACK setting is too high then throughput will be lost due to waiting for the ACK Window to timeout on lost packets By having the ability to adjust the ACK setting we can effective
40. r help CAUTI ON Any changes or modifications not expressly approved by the grantee of this device could void the user s authority to operate the equipment This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body CE Mark Warning This is a Class B product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures All trademarks and brand names are the property of their respective proprietors Specifications are subject to change without prior notification WL5460AP v2 User s Manual Table of Contents INTRODUCTION e el a l EE Ee 2 PARTS NAMES AND E Be LE 3 FACTORY DEFAULT NO O 5 WES ias 5 HARDWARE CONNECTION iara N E RAE NE EEA 6 ABOUT THE WIRELESS OPERATION MODES nadaa dde 7 ACCESSPOINT MODE iiO 8 CLIENT MODE INFRASTRUCTURE WEE 9 GUIENT MODEAAD2HOG seras ad 10 Eiere aere 11 WDS REPEATER MODE e leal 12 UNIVERSAL REPEAT ee 13 WISE C OLIENT ROUTER MODE sp icrataces na E
41. range Turns solid orange when wireless N A AP e s S MAC Ctrl Orange Turns solid orange when MAC Control N A Self oe OS Bridge Orange Turn solid orange when Bridge or N A 7 8 LAN 1 Turns solid green when linked to a Receiving Green Wired LAN 2 local network Sending data Table 1 LED Indicators 3 WL5460AP v2 User s Manual 2 Rear Panel Connection Ports 5460AP 5460AP v2 Trono metan SSS Ko fioe omnes e poweradepierpig eo fuam fomes OO OOOO Factory Press over 3 seconds to reboot this device RESET Press for over 10 seconds to restore factory settings Performing the Factory Reset will erase all previously entered device settings Table 2 Connection Ports 4 WL5460AP v2 User s Manual Factory Default Settings Device Name WL 5460AP v2 WEP Default value Disabled DHCP Server e In AP Client and Repeater mode the default DHCP Server is disabled Please set your PC s IP to the same subnet as the AP to access the AP e In WISP mode the default DHCP server is enabled Please restart your PC to renew the IP address DHCP Server IP Range 192 168 100 100 192 168 100 200 Table 3 Default Setting 5 WL5460AP v2 User s Manual Hardware Connection Note Before you starting hardware connection you are advised to find an appropriate location to place the Access Point Usually the best place for the Access Point is at the center of your wireless network with line of straight to all yo
42. rate only 2 4GHz B G 802 11b supported rate and 802 11g supported rate The default is 2 4GHz B G mode The SSID differentiates one WLAN from another therefore all access points and all devices attempting to connect to a specific WLAN must use the same SSID It is case sensitive and must not exceed 32 characters A device will not be permitted to join the BSS unless it can provide the unique SSID An SSID is also referred to as a network name because essentially it is a name that identifies a wireless network The default SSID is airlive Channel Number Allow user to set the channel manually or automatically If set channel manually just select the channel you want to specify If Auto is selected user can set the channel range to have Wireless Access Point automatically survey and choose the channel with best situation for communication The number of channels supported depends on the region of this Access Point All stations communicating with the Access Point must use the same channel The default channel is 13 18 WL5460AP v2 User s Manual Client Allow user to set the function Enabled or Disabled By the function all wireless clients can t mutual link but wireless client still link with LAN port adapter The default value is Disabled Press the setup button for detail configurations Wireless Security Setup Encryption None l oe Apply h t WPA PSK TKIP WPA PSK AES WPA2 PSK AES
43. ss AP first Site Survey Site survey displays all the active Access Points and IBSS in the neighborhood Press Site Survey button to search the wireless device Wireless Site Survey sem BSSID Channel Type Encrypt Signal PLANET 00 18 67 11 43 d6 11 B AP WEP Zb default 00 c0 0 2 te d3 b0 10 Du AP na 18 wlan 00 20 e0 39 a1 bb 316 AP WEP 16 Refresh Add MAC Address Enter MAC address of remote access point Press to discard the data you have entered since last time you press Apply Change Show Statisties Ustallpactelsinfomaton orrae Delete Selected To delete bridge from access to this Access Point you may firstly check the Select eg Delete All To delete all the clients from access to this Access Point just press Delete All ee ses 30 WL5460AP v2 User s Manual WDS Repeater Mode Setting Mir L ive OvisLink E y WLAN Access Point Mode Status TCP IP Reboot Other Upgrade Firmware Save Reload Settings Password Log NIP e aerate i Alias Name WDS Repeater Mode Settings Alias Name Wireless_AP Disable Wireless LAN Interface Band 24 GHz B G SSID lairlive Channel Number 13 El Wireless Client Isolation Disabled 902 1d Spanning Tree Disabled zl Security Setup WDS Security Advanced Settings Access Control Apply Changes You can set the alias name for this device limited not exceed 32 characters
44. t Other isLink N 9 bere werw ovislink com twag Reboot System Ae You want to warn boot this device Hor any puMmoses Reboot System Reboot 45 WL5460AP v2 User s Manual WLAN Access Point Mode Status TCP IP Reboot Other cave Reload Settings Password Log NIP Upgrade Firmware Select File Browse Browse Upload Reset Upgrade Firmware Upgrade Firmware Select File Browse Upload Reset 1 Download the latest firmware from your distributor and save the file on the hard drive 2 Start the browser open the configuration page click on Other and click Upgrade Firmware to enter the Upgrade Firmware window 3 Enter the new firmware s path and file name i e C FIRMWARE firmware bin or click the button to find and open the firmware file the browser will display to correct file path 4 Click button to start the upgrade function or button to clear all the settings on this page If firmware upgrade fail please see Appendix A Save Reload Settings Save Reload Settings Save Settings to File DAVE Load Settings from A File Browse Upload Reset Settings to Default Peset This function enables users to save the current configuration as a file i e config dat or loades configuration from a file Enter the file name or click to find the file from your computer Save Settings to File Click to save the current configuration to file Load Settings From Fil
45. ters format is recommended Group Key Life Time Enter the number of seconds that will elapse before the group key change ree ay Temuco O Encryption or WPA2 PSK authentication method is almost like WPA PSK You can choose the Pre Shared Key format and enter the Pre shared key Wireless Security Setup Encryption i EGS Pre Shared Key Format Passphrase y Pre Shared Key Group Key Life Time 86400 sec Apply Changes Reset Wireless Security Setup Encryption AIRE Pre Shared Key Format Passphrase Pre Shared Key Po Group Key Life Time B6400 sec Apply Changes Reset 21 WL5460AP v2 User s Manual Encryption You can select WPA2 PSK AES or WPA2 PSK Mixed method for data encryption Pre shared Key There are two formats for choice to set the Pre shared key e Passphrase and Hex If Hex is selected users will have to enter a 64 characters string For easier configuration the Passphrase at least 8 characters format is recommended Group Key Life Time Enter the number of seconds that will elapse before the group key change A cscs Mestanenutowae Wireless Security Setup Encryption 802 1 RADIUS Security Authentication RADIUS Server Port 1812 IP address Password IT Enable Accounting Accounting RADIUS Server Port 1813 IF address Password Apply Changes Reset Wireless Security Setup Encryption loz Tx FRADIUS Dm WPA AES AccountinyyPA2 AES WPA2 Mixed
46. tton for Wireless Client mode pt amea Bridge Select the Bridge and press Setup button for Wireless Bridge mode me ees WDS Repeater Select the WDS Repeater and press Setup button for Wireless WDS Repeater We ds configuration Universal Repeater Select the Universal Repeater and press Setup button for Wireless Universal repeater mode configuration Select the WISP and press Setup button for WISP Client Router mode configuration WISP Universal Select the WISP Universal Repeater and press Setup button for WISP Repeater Universal Repeater mode configuration 17 WL5460AP v2 User s Manual AP Mode Setting WLAN Access Point Mode Status TCP IP Other AP Mode Settings Alias Name Wireless AP Disable Wireless LAN Interface Band 2 4 GHz DH T SSID airlive sts lt CSsSCS Channel Number 13 IR Wireless Client Isolation Disabled zl Security Se Advanced Settings Access Control Apply Changes Alias Name You can set the alias name for this device Limited not exceed 32 characters O Disable Wireless Check the box to disable the Wireless LAN Interface by so doing you won t be able LAN Interface to make wireless connection with this Access Point in your located network In other words this device will not be visible by any wireless station Band You can choose one mode of the following you need 2 4GHz B 802 11b supported rate only 2 4GHz G 802 11g supported
47. ur wireless stations Also remember to adjust the antenna usually the higher the antenna is placed the better will be the performance 1 Connect to your local area network connect an Ethernet cable to one of the Ethernet port 2 LAN1 or LAN2 of this Wireless Access Point and the other end to a hub switch router or another wireless access point 3 Power on the device connect the included AC power adapter to the Wireless Access Point s power port and the other end to a wall outlet Check the LED The Power and LAN LED should be ON LAN LED will even blink if there is traffic The Link Act LED will be on in static when associated with a station and blink whenever this AP receives data packets in the air If the Status LED glows after self test it means the Wireless Access Point fails on self test Please ask your dealer for technical support 4 Please make sure your computer IP is in the same subnet as the AP i e 192 168 100 x 5 please make sure your computer has wireless network adapter installed 6 Open the web browser and enter http 192 168 100 252 6 WL5460AP v2 User s Manual About the Wireless Operation Modes The WL 5460AP v2 device provides all 7 modes of wireless operational applications with Access Point Mode Client Mode Bridge Mode WDS Repeater Mode Universal Repeater Mode WISP Client Router Mode WISP Universal Repeater Mode NO 0 bb ND eh This device is shi
48. www airlive com 802 11g Multi function Wireless Access Point User s Manual Declaration of Conformity We Manufacturer Importer OvisLink Corp SF NO 6 Lane 130 Min Chuan Rd Hsin Tien City Taipei County Taiwan Declare that the product 802 11 Multi function Wireless Access Point WL 5460AP WL 5450AP is in conformity with In accordance with 89 336 EEC EMC Directive and 1999 5 EC R amp TTE Directive Clause WEN 300 328 V1 6 1 2004 11 mw EN 301 489 1 V1 4 1 2002 08 mw EN 301 489 17 V1 2 1 2002 08 WEN 55022 1998 A1 2000 42 2003 WEN 55024 1998 A1 2001 42 2003 Mi EN 50385 WEN 60950 1 2001 A11 2004 E CE marking Signature Name Position Title Description Electromagnetic compatibility and Radio spectrum Matters ERM Wideband transmission equipment operating in the 2 4GHz ISM band And using spread spectrum modulation techniques Part 1 technical Characteristics and test conditions Part2 Harmonized EN covering Essential requirements under article 3 2 of the R amp TTE Directive Electromagnetic compatibility and Radio spectrum Matters ERM Electromagnetic compatibility EMC standard for radio equipment and Services Part 17 Specific conditions for wideband data and HIPERLAN equipment Limits and methods of measurement of radio disturbance characteristics of information technology equipment Information Technology equipment Immunity characteristics Limits and
49. you are located In other words this device will not be visible by any wireless station You can choose one mode of the following you need 2 4GHz B 802 11b supported rate only 2 4GHz G 802 11g supported rate only 2 4GHz B G 802 11b supported rate and 802 119 supported rate The default is 2 4GHz B G mode Channel Number In Bridge mode both wireless AP Router device need set to the same Channel e Security Please refer the AP mode settings gt Security for details kass WDS Security To enable security between wireless AP Router you can select WEP 64bits WEP 128bits WPA TKIP WPA2 AES for data encryption For WEP encryption Select ASCII if you are using ASCII characters Select HEX if you are using hexadecimal numbers 0 9 or A P For WPA WPA2 encryption you need enter the Pre Shared Key Information for the authentication purpose 29 WL5460AP v2 User s Manual WDS Security Setup Encryption WEP Key Format WEP Key Pre Shared Key Format Pre Shared Key Apply Changes Close Reset Advance Setting Please refer the AP mode settings gt Advance Setting for details AP MAC address Enter 12 digits in hex numbers in the AP MAC address BSSID field and press the Add MAC Address Button to associate with other s Wireless access point Before you want to use bridge mode to connect each other to provide A wireless bridge between 2 remote LANs you need add the BSSID of other s wirele
Download Pdf Manuals
Related Search