2.4GHz Digital Wireless A/V/Data Transmitter and Receiver KIT
Contents
1. 2 4GHz Digital Wireless A V Data Transmitter and Receiver KIT USER MANUAL MODEL 15 2400DK 1 Key Features a Offer a wireless link solution audio video data signals connection 2 4 GHz frequency hopping spread PEC LL module and supported max 25 Auto hopping channels for resisting interferences to other 2 4G devices LOOmW RF output Average Point to point mode only MPEG 4 D1 standard video compression and stereo audio inputs 5 bit I D pairing key for security Max 250 meters light of sight 2 Panel View gonn 9 15 2400DT 2 4G TX av n with rreauency Hoppinc O O LEO L AUDIO VIDEO IN n O O DC 12V IN QQ Lnn R POWER RS 485 O if RS 485 OUT OUT O O Termination O DC 12V IN DC 12V power input RS 485 I O 2 wire half duplex RS 485 supported AUDIO I O RCA female connectors for the stereo audio signal VIDEO I O BNC female for the analog CVBS video signal POWER ON or RF LINK LED Power RF LINK LED RF Link Loss Low Flashing RS 485 LED Indicated to RS485 data are transmitted or received ID Setting ID setting is use for paring with 15 2400DK transmitter and receiver each other It must be make a same ID code first before you setup the devices BAUD RATE and TERMINATION Baud rate and 120 Ohm termination setting by DIP switch Note After changing the baud rate setting by DIP switch please re boot the device again Baud Rate Setting 600 bps 2400 b2. 150 Meters 20 30 fos NTSC 17 25 fps PAL 100 Meters 30 fos NTSC 25 fps PAL Video Compression MPEG 4 Max Frame Rate NTSC 30 fps at 720 x 480 D1 vs Resolution PAL 25 fps at 720 x 576 D1 Bit Rate Up to 6Mbps Sampling Rate 48KHz Stereo S N Ratio 63dB Data RS 485 2 wire RS 485 Half Duplex Baud Rate 2400 4800 9600 bps Fixed Formats 1 Start bit 1 Stop bit 8 Data Bits No Parity 120 Ohm Termination Resistor ON OFF Setting Red LED Green LED RS 485 Data Link Status Dimensions 118 x 75 x 25mm without Antenna Weight without antenna 237 g 235 g FCC Part 15 Notice This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation
3. between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help 1 This Transmitter must not be co located or operating in conjunction with any other antenna or transmitter 2 This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body 3 Any changes or modifications including the antennas made to this device that are not expressly approved by the manufacturer may void the user s authority to operate the equipment Q2012 02 20
4. ps ANT SMA connector for connected to 2 4 GHz antennas 1 3 Quick Installation 3 1 To set the same ID code with Transmitter and Receiver each other by 5 bit DIP switch 3 2 To set the same Baud Rate with Transmitter and Receiver each other by 2 bit DIP switch 3 3 Plug the Video and Audio signals to the BNC and RCA connectors 3 4 Plug the 2 4G Antenna to SMA connector 3 5 Please check 12VDC input then power on the devices REMARK Avoid the frequency channels have the interference please don t close to the 802 11 a b g n AP routers and other 2 4GHz devices 4 Caution for Installation 4 1 Be careful never let any water in this equipment 4 2 If necessary use a soft cloth moistened with alcohol to wipe off the dust 4 3 Be extra careful not to shake the unit 4 4 Avoid places where temperatures exceed 50 C or higher 4 5 Avoid places where there are frequent vibrations or shocks When any abnormalities occur make sure to unplug the unit and contact your local dealer 5 Packing 5 1 Transmitter x1 5 2 Receiver x1 5 2 Antenna 5dBi x2 5 3 User manual x1 5 4 Screws x8 5 5 Plastic Conical Anchor x4 5 6 Power Adaptor x2 Option 6 Specification Items Models 15 2400DT 15 2400DR RE Frequency Channels 2400 2480 MHz 25 CH Auto Hopping FCC amp CE RTTE RF TX Power Modulation Min RX Sensitivity pe 80dBm RF Impedance 500 Distance vs Frame Rate 250 Meters 15 25 fps NTSC 13 21 fps PAL
Download Pdf Manuals
Related Search